Electromagnetic Wave Radiation Research Articles

Piezo‐Turned Magnet Rotation for ELF/SLF Cross‐Medium Communication in Omni‐Direction

AbstractExtremely/super low frequency (ELF/SLF) electromagnetic (EM) waves offer efficient propagation in challenging cross‐medium environments. However, conventional coil antennas, when emitting ELF/SLF EM waves, face constraints related to size, radiation efficiency, and high power consumption. To overcome these limitations, a disc‐rod structured piezoelectric rotating resonator is proposed, which can turn a NdFeB permanent magnet disc into rotation with an impressive high‐speed up to 10 000 r min−1 via wobbling motion of the rod tip, effectively generating ELF/SLF magnetic field radiation via rotational oscillation other than common linear and swinging oscillation of the magnetic dipole moments. The piezo‐turned magnetic rotation (PTMR) method leads to a two to five‐fold enhancement in magnetic field emission compared to existing piezo‐actuated acoustic resonant antennas, and a 370 times higher emitting efficiency compared to the traditional coil antenna with a comparable size. In contrast to unidirectional EM wave radiation at their solely resonant frequencies, the PTMR antenna showcases omnidirectional B‐field radiation with continuous tunability in a dual frequency band spanning from 10 to 100 Hz. Moreover, an air–seawater cross‐medium magnetic field communication is successfully demonstrated. With outstanding performance metrics, the PTMR antenna emerges as a promising solution for efficient long‐distance ELF/SLF cross‐medium communication.

Artery Pulse Waveform Acquired with a Fabry-Perot Interferometer.

For most patients admitted to a hospital, it is a requirement to continuously monitor their vital signs. Among these are the waveforms from ECG and the pulmonary arterial pulse. At present, there are several electronic devices that can measure the arterial pulse waveform. However, they can be affected by electromagnetic wave radiation, and the fabrication of electronic sensors is complicated and contributes to the e-waste, among other problems. In this paper, we propose an optical method to measure arterial pulse based on a Fabry-Perot interferometer composed of two mirrors. A pulse sensor formed by an acrylic cell with a thin membrane is used to gather the vasodilatation of the wrist, forming an air pulse that is enacted by means of a tube to a metallic cell containing a mirror that is glued to a thin silicone membrane. When the air pulse arrives, a displacement of the mirror takes place and produces a shift of the interference pattern fringes given by the Fabry-Perot. A detector samples the fringe intensity. With this method, an arterial pulse waveform is obtained. We characterize this optical device as a test of concept, and its application to measuring artery pulse is presented. The optical device is compared to other electronic devices.

SiC particles/Ti3C2Tx aerogel with tunable electromagnetic absorption performance in Ku band

In response to the issues stemming from electromagnetic wave (EMW) radiation or pollution, there has been a growing emphasis on the research and development of novel electromagnetic wave absorbing materials. In this work, we synthesized an EMW absorbing aerogel composed of SiC particles and Ti3C2Tx, with the structure regulated by PVA. The aerogel features a well-organized 3D network comprising Ti3C2Tx nanosheets (NSs), SiC particles, and PVA wires. At a mass ratio of 1:1 for SiC particles to Ti3C2Tx, the aerogel, when combined with PVA, demonstrated a remarkable reflection loss of -54.5 dB in the Ku band and an effective absorption bandwidth (EAB) of 5.4 GHz at a thickness of 2.04 mm. Even at low densities of 8.8 mg cm−3, the aerogel demonstrated significant mechanical strength, supporting a load equivalent to 1000 times its weight. The superior absorption capabilities of the SiC particles/Ti3C2Tx aerogel can be ascribed to the multiple interface polarization between Ti3C2Tx and SiC particles, and the impedance matching improved by the presence of PVA. These findings underscore the exceptional EMW absorption properties of the SiC particles/Ti3C2Tx aerogel, particularly in the Ku band.

SICK BUILDING SYNDROME experimental study on the effect of bio geometry design on electromagnetic (wi fi) waves in architectural spaces

ABSTRACT Electromagnetic wave are one of the most important source of the invisible pollutants, As these radiation increases with the advancement of the various transmission and wireless technology, When the rate of these electromagnetic wave radiation exceeds the safe or permissible limits, it becomes an environmental pollution affecting human health, especially within the architectural spaces, Which led to the emergence of science comes in the forefront of bio geometry, Which helps to protect against these harmful effects of modern technology while retaining them. The research attempts to reorganize the relationship between architectural design and negative effects of electromagnetic waves, and taking advantage of the organized energy of geometric shape, by conducting a set of laboratory experiments to verify the effect of bio geometry on electromagnetic contaminants within architectural spaces, The study of the effect of Wi Fi waves on groups of mice, Given the similarity of rat characteristics with human characteristics, to be studied, Access to results can be generalized to human, In collaboration with a group of health care professionals. One of the most important basic keys for generating this energy from geometric shapes is the center of the circle or any formation that results in movement (such as overlap, repetition, transparency), chromatic harmony, balance, and the qualitative effect of angles and numbers.

Development of high performance microwave absorption modified epoxy coatings based on nano-ferrites

With the rapid spread of wireless technologies and increasing electromagnetic energy, electromagnetic waves (EMW) have become a severe threat to human health. Therefore, minimizing the harmful effects of electromagnetic wave radiation is possible through the development of high-efficiency EMW absorption coatings. The aim of this work was to generate microwave absorbance coatings containing synthesized nano-CuFe2O4 and nano-CaFe2O4. Firstly, nano-CuFe2O4 and nano-CaFe2O4 were synthesized using the sol–gel method. Then, their structure, electrical, dielectric, and magnetic properties were investigated to find out the possibility of using these materials in high-frequency applications (e.g., microwave absorbance coatings). After that, two dosages (2.5 wt% and 5 wt%) of nano-CuFe2O4 and nano-CaFe2O4 were incorporated into epoxy resin to prepare modified epoxy resin as microwave coatings. The dielectric studies show that the AC conductivity of the prepared samples is high at high frequencies. Additionally, the magnetic properties reveal a low coercivity value, making these samples suitable for high-frequency devices. The microwave results illustrate that adding nano-ferrites with high content enhances the absorption characteristics of the tested films. The results showed that the two films have two absorption bands with RL < –10 dB ranging from 10.61 to 10.97 GHz and from 10.25 to 11.2 GHz. The minimum return loss achieved for the two cases is −13 and −16 dB, respectively. Indicating that the film coated with CuFe has a better absorption value than the one coated with CaFe.

Partial Discharge Detection Method of Electrical Equipment Based on UHF Method

Partial discharge is an early symptom of insulation defects. In the field application, the detection method can not accurately identify those noise signals mixed in the partial discharge signal, which limits the detection to a certain extent. Based on UHF method, a partial discharge detection method for electrical equipment is designed. When partial discharge occurs, the exchange between charges, the radiation of electromagnetic waves and the consumption of energy will occur at the discharge position, causing the change of electrode potential. For the phase distribution spectrum, the signal characteristics produced by partial discharge are extracted from three aspects: statistical information, time domain information and frequency domain information. During detection, UHF sensor is placed on the basin insulator, and then UHF signal is received. Insulation defects are identified according to various differential discharge patterns formed by the discharge characteristics of different defects. Test results show that the signal spectrum detected by UHF partial discharge roughly matches the typical discharge spectrum, and it is determined that there is partial discharge in this area. This method has high positioning accuracy and meets the detection requirements of electrical equipment.

Second Harmonic Electromagnetic Wave Emissions from a Turbulent Plasma with Random Density Fluctuations

In the solar wind, electromagnetic waves at the harmonic plasma frequency 2ω p can be generated as a result of coalescence between forward- and backward-propagating Langmuir waves. A new approach to calculate their radiation efficiency in plasmas with external background density fluctuations is developed. The evolution of Langmuir wave turbulence is studied by solving numerically the Zakharov equations in a two-dimensional randomly inhomogeneous plasma. Then, the dynamics of the nonlinear electric currents modulated at frequencies close to 2ω p are calculated, as well as their radiation into harmonic electromagnetic waves. In the frame of this non-self-consistent approach where all transformations of Langmuir waves on density inhomogeneities are taken into account, the electromagnetic wave radiation rate (emissivity) is determined numerically as well as analytically, providing in both cases similar results. Moreover, scaling laws of the harmonic wave emissivity as a function of the ratio of the light velocity to the electron plasma thermal velocity are found. It is also shown how the emissivity depends on the average level of density fluctuations and on the isotropic/anisotropic character of the Langmuir waves’ and density fluctuations’ spectra.

Electromagnetic radiation estimation at the ground plane near fifth‐generation base stations in China by using machine learning method

AbstractA novel method based on machine learning is proposed to estimate the electromagnetic radiation level at the ground plane near fifth‐generation (5G) base stations. The machine learning model was trained using data from various 5G base stations, enabling it to estimate the electric field intensity at any arbitrary radiation point when the base station provides service to different numbers of 5G terminals which are in different service modes. The inputs required for the model include the transmit power of the antenna, the antenna gain, the distance between the 5G base station and 5G terminals, terminal service modes, the number of 5G terminals and the environmental complexity around the 5G base station. Experimental results demonstrate the feasibility and effectiveness of the estimation method, with the mean absolute percentage error of the machine learning model being approximately 5.98%. This level of accuracy showcases the reliability of the approach. Moreover, the proposed method offers low costs when compared with on‐site measurements. The estimated results can be utilised to reduce test costs and provide valuable guidance for optimal site selection, thereby facilitating radio wave coverage or electromagnetic radiation regulation of 5G base stations.

Mapping of Electromagnetic Field Radiation Intensity in the JL Base Transceiver Station (BTS) Area. Kenangan 05 and the Impact of Health in Society

&#x0D; &#x0D; &#x0D; &#x0D; Electromagnetic waves are a type of wave phenomenon. Electromagnetic waves are transverse waves that arise due to changes in electric fields and magnetic fields that oscillate with each other. Electromagnetic waves can be generated, one of the ways, from BTS towers so that they can produce intense electromagnetic field radiation. Health problems resulting from exposure to electromagnetic wave radiation cannot be felt directly. However, the longer you are exposed to electromagnetic wave radiation, the more dangerous it will be to your body's health. The aim of this research is to carry out mapping from measuring the intensity of electromagnetic field radiation in the BTS area and to determine the health impact of large electromagnetic field radiation on the surrounding community. Data processing in this research was carried out using quantitative techniques and qualitative techniques, namely by measuring the intensity of the electric field and magnetic field of electromagnetic waves and evaluating the results of the intensity of electromagnetic field radiation as well as conducting interviews as a public health survey. The data obtained in this research was processed using ArcGis and Surfer software for mapping results. Based on the evaluation and mapping results, it shows that the intensity of electromagnetic field radiation is still below the threshold value according to the 2020 ICNIRP standards. Based on the results of this research, there are no significant health effects occurring in the surrounding community.&#x0D; &#x0D; &#x0D; &#x0D;

Investigation of electrical conductivity and electromagnetic wave absorption capabilities of water hyacinth biocarbon impregnated with Cu atom

This paper discusses the impregnation of Cu atoms at carbonization temperature of water hyacinth bio carbon composite. This composite is used as an absorber of electromagnetic waves. Because the inference of electromagnetic waves can cause damage to other electronic equipment. In addition, electromagnetic wave radiation can cause various human health problems. The purpose of the research is to obtain a material that is able to absorb electromagnetic waves and increase electrical conductivity, impregnation of Cu atoms at carbonization temperature of water hyacinth bio carbon composite. The composite material uses a composition ratio of water hyacinth powder and phenol-formaldehyde of 30:70. The carburization temperatures used were 600 °C, 800 °C, and 1000 °C with a heat increase rate of 7 °C/minute. This study used Scanning Electron Micrograph (SEM), X-Ray Diffraction (XRD), LCR Meter, and vector network analyzer. The results show that the impregnation of Cu atoms at carbonization temperature can increase the area of the nanostructure, thereby increasing the formation of micropores in the composite. The higher the carbonization temperature, the percentage of Cu and carbon compounds can increase, while the percentage of crystal structure decreases. Impregnation of Cu atoms further strengthens the composite's absorption of electromagnetic wave radiation. Impregnation of Cu atoms in water hyacinth bio carbon composites at carbonization temperature can increase the electrical conductivity of the composite. The results of this research have potential applications in the electronics industry, batteries, and electrical devices, and can be used to protect devices from electromagnetic interference, especially in telecommunications and the medical field

Lightweight aramid nanofibers/carbon nanotubes/MnFe2O4 composite aerogel for highly efficient microwave absorption

With the booming development and wide applications of modern communication technology, wearable devices are becoming more and more popular in our life. Meanwhile, the pollution and radiation of electromagnetic wave (EMW) is becoming increasingly prominent and threating to human health, equipment operation and military security. Multi-component regulation and spatial microstructure design of microwave absorption materials is an effective strategy for solving the pollution and radiation of electromagnetic wave. Herein, aramid nanofibers/carbon nanotubes/MnFe2O4 (ACF) composite aerogel were prepared through the combination of freeze-drying technique and hydrothermal method. Impedance matching of aramid nanofibers/carbon nanotubes aerogel is improved by introducing MnFe2O4 particles, inducing to that EMW is more easily incident into aerogel and then attenuated by microwave absorber. In addition, the three-dimensional networks structure of aerogel can enhance the multiple reflection and scattering, and improve the loss capacity of EMW. ACF05 aerogel exhibits a minimum reflection loss of −64.6 dB at 12.0 GHz and broad effective absorption bandwidth of 5.0 GHz under thickness of 2.1 mm. The excellent microwave absorption (MA) performance of ACF aerogel mainly comes from the synergistic effect of three-dimensional networks structure, impedance matching, dielectric loss and magnetic loss.

A COMPACT HONEYCOMB-STRUCTURED RECONFIGURABLE ANTENNA WITH COPLANAR WAVEGUIDE FEED FOR MULTIBAND WIRELESS APPLICATIONS

The design and implementation of reconfigurable antennas in wireless applications play a tremendous role in minimizing the hardware size of wireless devices. An antenna with the potential to vary its frequency of operation, radiation pattern, and polarization according to the requirement is known as a reconfigurable antenna. Here a novel honeycomb-structured frequency and pattern-reconfigurable monopole antenna has been designed. A honeycomb structure provides better bandwidth as it has multiple edges; angles of the hexagon allow for more efficient radiation and reception of electromagnetic waves and it offers a symmetric radiation pattern. It is compact, with higher packing density. A lowcost FR-4 substrate with a thickness of 1.5 mm and a compact size of 25 mm &amp;times; 42 mm is used in the design. The antenna can be operated in four modes using two PIN diodes. In mode 0 it can resonate at 2.4 GHz, which is commonly used for Wi-Fi and Bluetooth communication, while in mode 1 it operates at 2.8 GHz and 1.8 GHz for mobile communication. In mode 2 it operates at 2.7 GHz as well as 1.8 GHz, and in mode 3, it works at 1.8 GHz and 3.6 GHz for WiMAX communication. This antenna has a peak gain value of 3.99 dBi. Thus, by changing the geometry/structure, antenna performance can be improved. The proposed design is fabricated on FR-4 substrate material, and the parameters such as return loss (S&lt;sub&gt;11&lt;/sub&gt;) and bandwidth are validated. The simulated results and the measured results match well.

Terahertz microcomb oscillator stabilized by molecular rotation

Controlling the coherence between light and matter has enabled the radiation of electromagnetic waves with a spectral purity and stability that defines the Système International (SI) second. Transitions between hyperfine levels in atoms are accessible in the microwave and optical domains, but faithfully transferring such stability to other frequency ranges of interest requires additional components such as optical frequency combs. Such spectral purity and stability are specifically sought out for the terahertz domain for both scientific and commercial applications, including precision studies of molecular physics, next-generation wireless communications, quantum sensors, and terahertz frequency standards. Currently, there is a lack of native frequency references in this spectral range, which is essential for the consistency of measurements and traceability. Small-scale terahertz oscillators, which leverage dissipative Kerr soliton microcombs, present a promising avenue for the generation of terahertz waves that rival the spectral purity of electronic alternatives. Here, we experimentally demonstrate the rotational spectroscopy of nitrous oxide (N2O) with a microcomb-based oscillator. To mitigate the frequency drift encompassed in such waves, we lock the frequency of the microcomb terahertz oscillator to that of a rotational transition of N2O, reducing the fractional frequency stability to a level of 5 × 10−12 at 10 s of averaging time. These results constitute a high performance terahertz oscillator that can be scaled down to a compact size while circumventing the need for frequency multiplication or division of frequency standards. This demonstrates a foundational component needed for future terahertz applications.

METHOD OF REDUCING THE LEVEL OF BACK RADIATION OF ELECTROMAGNETIC WAVES OF APERTURE ANTENNAS

A method has been proposed and developed that allows you to significantly reduce the level of back radiation of electromagnetic waves of aperture-type antennas of any design. The essence of the method is the excitation of slowed surface waves on the outer side of the edge of the antenna aperture, which are in antiphase with electromagnetic waves of back radiation. Slowed surface waves are formed by an impedance metal comb, which performs the function of a retarding system, placed on the outer side of the opening edge of the antenna. The dependence of the formed characteristics of the electromagnetic field on the design parameters of the impedance comb is shown. The method was tested on the horn-slot ship antenna of the “Mius” type navigation radar station. The results of modeling and calculation of the directional pattern (DP) of the antenna confirm that the proposed method allows to reduce the level of the rear lobe of the directional pattern of the horn-slit antenna with an impedance comb by approximately 1.4 times.

Development of barium hexaferrite core–shell composites as high-performance microwave absorption by optimizing hydrothermal synthesis

In conjunction with the enhancement of societal living standards and the rapid development of information technology, an extensive variety of high-capacity electronic devices are being introduced to the market. The heightened demands result in the generation of electromagnetic wave radiation, which poses a potential risk to human well-being. Barium hexaferrite (BHF) is one of the radar-absorbing materials (RAMs) that can absorb electromagnetic waves because it has a high anisotropic field. However, its drawbacks are narrow absorption and less stability. Molybdenum disulfide (MoS2), is the best candidate for the reinforcement of BHF. The study investigated the impact of increasing the thiourea, temperature, hydrothermal holding time, and sample thickness on reflection loss. This study used a two-step molten salt and hydrothermal synthesis to make a BaFe12O19@MoS2 core-cell composite. Two-step molten salt and hydrothermal synthesis methods created single-phase BaFe12O19@MoS2 core-cell composites that worked well. The results showed that adding MoS2 to BHF changed BHF's magnetic properties from hard to soft. Increasing the hydrothermal temperature up to 220 °C effectively reduced the reflection loss of BaFe12O19@MoS2. On a 2 mm thick sample containing 100 mmol thiourea, the study achieved an electromagnetic wave absorption of 99.97 % with a reflection loss of –35.41 dB (17.37 GHz). The results of this research can be applied to protect electronic devices vulnerable to signal interference from satellite radar systems at frequencies of 12–18 GHz

МАТЕМАТИЧНА МОДЕЛЬ ДОСЛІДЖЕННЯ КОЕФІЦІЄНТІВ ВІДБИТТЯ ВІД РУПОРНИХ ВИПРОМІНЮВАЧІВ ФАЗОВАНИХ АНТЕННИХ РЕШІТОК

The article is devoted to the problem of researching reflection coefficients from horn emitters that are part of a phased antenna array. It was found that the advantage of using horn antennas is the high directivity of their radiation, a significant efficiency and a fairly high amplification factor. However, their main drawback is the back radiation (scattering) of electromagnetic waves by the elements of the antenna design. This affects the radar visibility of samples of weapons and military equipment and their electromagnetic compatibility. To eliminate these shortcomings, the article analyzes the differential characteristics of the backscatter diagrams of aperture antennas in order to improve the mathematical model of the reradiated field study, taking into account the reflection coefficients from horn emitters. In the course of the study, the causes and regularities of such a phenomenon as the reflection of electromagnetic waves from internal inhomogeneities of horn antennas were clarified, in order to reduce it. The given graphs of the dependence of the amplitudes of the reflected electromagnetic field on the observation angles show that the improvement of the alignment in the antenna path will cause an increase in the maximum signal amplitude in the transmission mode. According to the principle of inversion of antennas, such an arrangement will improve the absorption of waves of higher types directed to the openings of a single emitter or an equidistant antenna array. This will reduce the voltage standing wave factor and the level of side lobes. Therefore, the sounding radar station will receive a reduced level of the reflected signal, which will improve the defense of weapons samples that include a horn as a separate antenna or as part of equidistant linear phased antenna arrays. Keywords: phased antenna array; pyramidal horn emitter; reduction of the effective scattering surface; reflection coefficient.

Numerical Simulation on Microwave Melting of Hastelloy C-276

Melting of metals is of utmost importance in the manufacturing industry as it is the primary manufacturing process to obtain the desired shape and size. microwave melting is a novel technique that uses electromagnetic wave radiation to heat materials. In the present work, the melting of Hastelloy C-276 inside a multimode microwave applicator operating at 2.45 GHz and 900 W input power, is explored in numerical and experimental. This results in a significant reduction in processing time and leads to lesser material wastage. The distribution of temperature, electric field, and resistive losses was analysed to understand the microwave melting of the Hastelloy C-276 sample. The study revealed that the melting time taken was ~440 seconds for microwave melting of Hastelloy C-276.

ANALYSIS OF RESISTANCE OF CASSAVA TAPE BY EXPOSURE TO 1000 μT INTENSITY ELF MAGNETS

Extremely Low Frequency (ELF) electromagnetic waves are electromagnetic waves with a frequency range of 0 to 300 Hz. ELF electromagnetic wave radiation produces non-thermal effects on the biological objects used, meaning that it does not cause temperature changes when interacting with or inducing the system. Electromagnetic waves are waves that arise due to changes in electric fields and strong magnetic fields. This research aims to prove the effect of Extremely low frequency (ELF) magnetic field on the food resilience process. The research method used is experimental research method. This research was carried out in the basic physics laboratory at the University of Jember. Data collection techniques using observation. Based on the research, it can be concluded that ELF magnetic field radiation has the potential as an alternative method in increasing the nutritional value and durability of fermented food ingredients. Exposure to Extremely Low Frequency magnets with an intensity of 1000 μT for 45 minutes resulted in changes in pH value and physical quality that affect food durability in cassava tape.

Антенна импульсного георадара

Resistive-loaded dipoles of various lengths, for different frequency ranges, are widely used in GPR suvey of subsurface ground structures. At the same time, in most cases, a transmitter with a fixed pulse length is used, which does not always allow you to fully use the characteristics of the antenna. Directional antennas for high-power georadars with amplitudes of the generated signal of 5 kV and higher are considered. A method of matching a directional resistively loaded antenna with a transmitter, implemented using a gas-filled spark gap, is proposed, while some elements are transferred from the transmitter to the antenna and resistors of a resistively loaded dipole are part of a pulse generator. As a result, the antenna is aligned with the pulse duration and produces more efficient electromagnetic wave radiation. Also, the antenna design allows you to select the necessary directional pattern by selecting either the maximum of the main lobe, or maximize the side lobes. The use of a metal shield reduces the emission of electromagnetic radiation to the operator of the georadar, and may allow to increase the radiated power of classical georadars and, consequently, increase their dynamic range.

THE EFFECTIVENESS OF USING SCREENS ON COMPUTER MONITORS AGAINST EYE MUSCLE FATIGUE OF EMPLOYEES AT THE AMBON CITY EDUCATION OFFICE IN 2023

Eye fatigue is a somatic disorder in the ciliary muscle of the eye that is forced to work to see close objects for long periods of time. Computers as electronic devices use electrical energy and electromagnetic radiation waves that are harmful to eye health. The installation of Antiglare Screen on a computer monitor is believed to reduce complaints of eye muscle fatigue so it needs to be reviewed for the effectiveness of its use. It is known the effectiveness of using screens on computer monitors to reduce eye muscle fatigue of employees at the Ambon City Education Office in 2023. Quantitative research design with quasy experiment method. Using Simple Random Sampling technique as many as 30 respondents. Data collection techniques using questionnaires and interventions using screen monitors measured by the photostress recovery test method. The measurement results are analyzed by the repeated-measured anova statistical test. The average prevalence value of eye muscle fatigue ≥ 50 seconds before the screen installation intervention on a computer monitor. After the intervention, post-measurement of 1 right eye on the fourth day amounted to 14.833 seconds, the OR value was 0.028, for the left eye it was 14.633 seconds, the OR value was 0.001. Post measurement-2 of the right eye on the sixth day of 26.367 seconds of OR value of 0.026, for the left eye of 25.533 seconds OR value 0.016. Furthermore, Post measurement-3 right eye on day 10 amounted to 35,200 seconds OR value -0.001, for left eye 35,700 seconds OR value -0.038. There was a difference in the average fatigue of the eye muscles in three post-measurements using the photostress recovery test method. Post-measurement variable-3 on day 10 of the intervention using a computer monitor screen had an effect on reducing eye muscle fatigue. The longer respondents use antiglare screen, the less eye muscle fatigue. Although there were respondents who had refractive errors, the use of screen monitors was effective in reducing fatigue of the right eye OR (-0.001) and left eye OR (-0.038). Computer users must have occupational safety and health awareness in using computers. Pay attention to the arrangement of the workspace and optimize eye rest time by occasionally turning your eyes to the green area filled with trees outdoors.