Electrode Materials For Batteries Research Articles

Dual Ion Co-Insertion Induced Spontaneous and Reversible Phase Conversion Chemistry for Unprecedented Zn2+ Storage.

Prussian blue analogues are highly promising electrode materials due to their versatile electrochemical activity and low cost. However, they often suffer from severe structural damage caused by the Jahn-Teller distortion and dissolution of high-spin outer metal ions, resulting in poor cycle life. Material modification and electrolyte regulation have been the common approaches to address this issue, albeit with very limited success. We report here a novel and efficient strategy to preserve structural stability by co-inserting Co2+ and Zn2+ ions in KCo[Fe(CN)6]. This co-insertion induced a spontaneous and reversible phase conversion by the replacement of low-spin inner ion (Fe3+), which efficiently relieves structural damage caused by Jahn-Teller distortion and metal-ion dissolution, leading to an outstanding Zn2+ storage capacity and an exceptional improvement of cycle life with a capacity retention of 97.7 % over 4400 cycles at 40 C. We also demonstrated the enhancement of co-intercalation on ion migration using a combined approach of experimental and density functional theory (DFT) calculations. This work provides an important progress to solve the cycle stability of Prussian blue analogues towards their practical application as electrode materials for aqueous batteries.

Dual Ion Co‐Insertion Induced Spontaneous and Reversible Phase Conversion Chemistry for Unprecedented Zn2+ Storage

AbstractPrussian blue analogues are highly promising electrode materials due to their versatile electrochemical activity and low cost. However, they often suffer from severe structural damage caused by the Jahn–Teller distortion and dissolution of high‐spin outer metal ions, resulting in poor cycle life. Material modification and electrolyte regulation have been the common approaches to address this issue, albeit with very limited success. We report here a novel and efficient strategy to preserve structural stability by co‐inserting Co2+ and Zn2+ ions in KCo[Fe(CN)6]. This co‐insertion induced a spontaneous and reversible phase conversion by the replacement of low‐spin inner ion (Fe3+), which efficiently relieves structural damage caused by Jahn–Teller distortion and metal‐ion dissolution, leading to an outstanding Zn2+ storage capacity and an exceptional improvement of cycle life with a capacity retention of 97.7 % over 4400 cycles at 40 C. We also demonstrated the enhancement of co‐intercalation on ion migration using a combined approach of experimental and density functional theory (DFT) calculations. This work provides an important progress to solve the cycle stability of Prussian blue analogues towards their practical application as electrode materials for aqueous batteries.

In Situ Synthesis of MoO3 by Surface Oxidation of Mo2C (MXene) for Stable Near-Surface Reactions in Aqueous Aluminum-Ion Battery.

Molybdenum trioxide (MoO3) is a promising positive electrode material for aqueous aluminum-ion batteries (AAIBs) due to its high theoretical capacity. However, MoO3 faces several challenges in an aqueous electrolyte, such as easy dissolution of reaction products, volume expansion, and low conductivity, which severely limit its application in aqueous batteries. In this work, we effectively increased the overall conductivity of the electrode by in situ growing MoO3 on the Mo2C MXene layer. MXene can effectively inhibit the dissolution and structural loss of MoO3 reaction products. Additionally, the coordination effect of Mo2C and MoO3 achieves a stable near-surface reaction on the MXene laminates, resulting in the Mo2C/MoO3 composite exhibiting excellent aluminum storage properties (123.5 mAh/g after 200 cycles at 0.4 A/g). The energy storage mechanism of H+/Al3+ co-insertion/extraction was elucidated through ex situ characterization, and the promotion effect of Mo2C on MoO3 reaction kinetics was verified by density functional theory (DFT) calculations. This work provides new insights into improving the stability of AAIBs cathodes and extends the application of Mo-based MXene in aqueous batteries.

Development of Sodium-Lithium-Manganese-Cobalt Oxide with B Doping or B/F Dual Doping as Cathode Electrode Materials for Sodium-Ion Batteries

Development of Sodium-Lithium-Manganese-Cobalt Oxide with B Doping or B/F Dual Doping as Cathode Electrode Materials for Sodium-Ion Batteries

Intercalation Behavior of a Spiro-bipyrrolidinium Cation into a Graphite Electrode from Dimethyl/Propylene Carbonates.

Quaternary ammonium-graphite intercalation compounds (QA+-GICs) are promising negative electrode materials in dual-carbon batteries by virtue of safety, low cost, and environmental friendliness. However, the intercalation behavior of QA+ into graphite electrodes in mixed solvents has never been reported. Herein, spiro-(1,1')-bipyrrolidinium tetrafluoroborate dissolved in a dimethyl/propylene carbonate (DMC/PC) binary solvent system was employed in graphite/activated carbon (AC) capacitors. The storage behavior of the spiro-(1,1')-bipyrrolidinium cation into graphite is very related to the solvent composition of the electrolyte solutions. In situ X-ray diffraction tests revealed that the graphite electrodes can form different QA+-GICs during cycling, which is a key factor influencing the electrochemical performance of graphite/AC capacitors. Besides, the reversible thickness change of graphite in graphite/AC capacitors with different electrolytes during the charge-discharge process was also addressed. These findings provide sound evidence for the co-intercalation of the solvent with the cation.

Multilayer-coating process for the synthesis of nickel-silicate composite with high Ni loading as high-rate performance lithium-ion anode material

BackgroundMetal silicates possess several important advantages as electrode materials for lithium-ion batteries (LIBs), including straightforward synthesis, low cost, and high thermal stability. A green synthesis routes that are capable of increasing metal loading and reducing the impact on the environment are required. MethodsA Ni-silicate with a multilayer structure and a Ni/Si molar ratio of 0.25 is first prepared using the co-precipitation method. The as-synthesized product is then repeatedly immersed in a Ni2+ solution to obtain Ni-silicate with the desired Ni contents (Ni/Si molar ratio: 0.50–2.00). Finally, the resulting Ni-silicate is reconstructed by hydrothermal treatment under various temperatures (70 °C, 100 °C, 150 °C) and durations (3 h and 24 h) to obtain Ni-phyllosilicate. The effects of the hydrothermal treatment temperature, hydrothermal time, and Ni/Si ratio on the structure, morphology, and surface area of the Ni-silicate composites are examined. Significant FindingsThe Ni-silicate with a Ni/Si ratio of 1.5 has a reversible capacity of 729 mAhg-1, which exceeds traditional graphite anodes (372 mAhg-1). Furthermore, the material exhibits a capacity retention of up to 80 % as the current density is increased from 0.025 Ag-1 to 0.5 Ag-1. Thus, the synthesized Ni-silicate composite is a promising candidate material for LIB anode.

A metallic lithium anode for solid-state batteries with low volume change by utilizing a modified porous carbon host

Lithium metal is a promising negative electrode material for solid-state batteries (SSBs). However, uncontrolled lithium deposition and stripping cause several issues during cycling. Herein, the microporous carbon YP-50F and its modifications obtained by thermal ethene-based chemical vapor deposition (CVD) are investigated as 3D host to accommodate and control the deposition of metallic lithium. In half-cells vs. lithium, the CVD-YP composite electrode with Li6PS5Cl electrolyte shows significantly higher initial coulombic efficiency (79.5 %) than the pristine carbon (55.3 %) due to the reduction of side reactions. The metallic character of the deposited lithium is evidenced by 7Li Nuclear Magnetic Resonance spectroscopy. However, full cells with nickel-rich NCM (LiNi0.9Co0.05Mn0.05O2) positive electrode and CVD-YP composite negative electrode show reasonable performance over 50 cycles without occurrence of (micro-) short-circuits (in contrast to 2D reference electrodes). In addition, small prototype pouch cells are investigated and the thickness change during (dis)charging is less than one third compared to a bare lithium metal electrode. This demonstrates low breathing behavior of the CVD-YP electrode and confirms the reversible storage of metallic lithium within the 3D carbon-based composite electrode.

DFT and AIMD studies of SnFe2O4 as a promising anode for Li-ion batteries

Tin ferrite (SnFe2O4) is considered as a perspective lithium ion battery anode, owing to its low cost, large theoretical capacity, low toxicity, structural stability, and easy synthesis method. Prior research has been done on the performance of lithium storage in SnFe2O4. However, the electrochemical processes that take place during the lithiation-delithiation cycle of LIBs have not been explained in depth yet. In order to understand the discharge mechanism in the LixSnFe2O4 anode (x = 0 to 2), we systematically investigated its electrochemical characteristics, structural and electronic properties, average formation energies, open-circuit voltages, diffusion coefficient, and volume expansion using density functional theory. According to our calculations, an increase in Li concentration x up to 1.125 leads to enhanced stability of the LixSnFe2O4 systems. During this process, Li+ ions prefer to be intercalated at the octahedral 16c sites, inducing the displacement of Sn2+ ions from tetrahedral sites 8a to 16c and 48f sites. However, for 1.125 < x < 2, lithium ions tend to occupy the less stable sites 48f , which reduces the stability of LixSnFe2O4 systems.Additionally, the calculated lithium intercalation voltage for full lithiation Li1.125SnFe2O4 is equal to 1.5 V, and the distortion of the LixSnFe2O4 system occurs at a voltage of 0.75 V, which is in well agreement with experimental results. The Li-coefficient diffusion on SnFe2O4 at 300 K is calculated by ab initio molecular dynamic simulation and equal to 8.22 × 10−8 cm2/s, which indicates the excellent mobility of Li ions in SnFe2O4. Considering all these results, we can suggest SnFe2O4 as a promising negative electrode material for lithium-ion batteries.

In-situ synthesis AgO/AgNPs composite as binder-free cathode for high-performance aqueous AgO-Al batteries

Aqueous AgO-Al batteries are promising systems due to their ultrahigh specific capacity, energy density, and stable output voltage. However, they still suffer from the low utilization and sluggish kinetics of the cathode. In this study, the binder-free AgO/AgNPs composites were synthesized in-situ using a simple electrodeposition method. Due to the excellent conductivity and rich mesoporous structure of AgO/AgNPs materials, the electron and ion transfer kinetics were enhanced, thereby improving the charge storage performance of the electrode. As expected, the AgO-Al battery with the optimized AgO/AgNPs composite cathode demonstrated excellent rate performance, achieving a high discharge capacity of 325.1 mAh g−1, and a stable operating voltage platform of 1.55 V at the current density of 1000 mA cm−2. The maximum energy and power density were 687 Wh kg−1 and 6.2 kW kg−1, respectively. This work presents an effective strategy for designing high-performance AgO electrode materials for AgO-Al batteries.

Unveiling electrochemical insights of lithium manganese oxide cathodes from manganese ore for enhanced lithium-ion battery performance

Implementing manganese-based electrode materials in lithium-ion batteries (LIBs) faces several challenges due to the low grade of manganese ore, which necessitates multiple purification and transformation steps before acquiring battery-grade electrode materials, increasing costs. At present, most Lithium Manganese Oxide (LMO) materials are synthesized using electrolytic manganese dioxide, and the development of new processes, such as hydrometallurgical processes is important for achieving a cost-effective synthesis of LMO materials. In this work, we develop a full synthesis process of LMO materials from manganese ore, through acid leaching, forming manganese sulfate monohydrate (MnSO4·H2O), an optimized thermal decomposition (at 900, 950 or 1000 °C) producing different Mn3O4 materials and a solid-state reaction, achieving the synthesis of LMO. The latter was used as a cathode material for LIB exhibiting a specific capacity comparable to the state-of-the-art LMO cathode with a remarkable cycling stability of 800 cycles with <20 % in capacity loss. These performances were attributed to the excellent redox reversibility of the LMO cathode, characterized by voltammetry and in operando and in situ characterization by Raman and XRD.

Pushing the Energy-Lifetime Frontier of Li-Ion Batteries: Study of Ni-Rich, Co-Free NMAW Cathode Material

Abstract Dopants and coatings have been widely used to improve the performance of Ni-rich positive electrode active materials. Previous studies have aimed to elucidate the mechanism by which Al and W improve lithium metal oxides, providing valuable insight on the design of enhanced electrode materials for Li-ion batteries. In this work, Al and W are compared as individual dopants as well as co-dopants in order to design an optimal Ni-rich, Co-free material. This involved studying the effect of synthesis temperature in the presence of Al and/or W as well as the effect that these metals have on the morphology of the resultant polycrystalline materials. In addition, structural analysis by X-ray diffraction, electrochemical analysis, and characterization of the mechanical strength of the materials were also conducted. The change in performance with the addition of Al and W depends greatly on particle size and chemical composition. Small sized Ni-rich polycrystalline particles (Ni content of 94%) with low contents of Al (3%) and W (1%) showed the greatest enhancement in energy density with good cycle life.

Machine learning-assisted DFT-prediction of pristine and endohedral doped (O and Se) Ge12C12 and Si12C12 nanostructures as anode materials for lithium-ion batteries

Nanostructured materials have gained significant attention as anode material in rechargeable lithium-ion batteries due to their large surface-to-volume ratio and efficient lithium-ion intercalation. Herein, we systematically investigated the electronic and electrochemical performance of pristine and endohedral doped (O and Se) Ge12C12 and Si12C12 nanocages as a prospective negative electrode for lithium-ion batteries using high-level density functional theory at the DFT/B3LYP-GD3(BJ)/6-311 + G(d, p)/GEN/LanL2DZ level of theory. Key findings from frontier molecular orbital (FMO) and density of states (DOS) revealed that endohedral doping of the studied nanocages with O and Se tremendously enhances their electrical conductivity. Furthermore, the pristine Si12C12 nanocage brilliantly exhibited the highest Vcell (1.49 V) and theoretical capacity (668.42 mAh g− 1) among the investigated nanocages and, hence, the most suitable negative electrode material for lithium-ion batteries. Moreover, we utilized four machine learning regression algorithms, namely, Linear, Lasso, Ridge, and ElasticNet regression, to predict the Vcell of the nanocages obtained from DFT simulation, achieving R2 scores close to 1 (R2 = 0.99) and lower RMSE values (RMSE < 0.05). Among the regression algorithms, Lasso regression demonstrated the best performance in predicting the Vcell of the nanocages, owing to its L1 regularization technique.

Synthesis and characterization of MoS2-carbon based materials for enhanced energy storage applications

The article delves into the synthesis and characterization of MoS2-carbon-based materials, holding promise for applications in supercapacitors and ion batteries. The synthesis process entails the preparation of MoS2 and its carbon hybrids through exfoliation, hydrothermal treatment, and subsequent pyrolysis. Various analytical techniques were employed to comprehensively examine the structural, compositional, and morphological properties of the resulting materials. The article explores the electrochemical performance of these electrode materials in supercapacitors and ion batteries (LiB, SiB, KiB). Electrochemical measurements were conducted in aqueous electrolyte for supercapacitors and various aprotic electrolytes for ion batteries. Results highlight the impact of the synthesis process on electrochemical performance, emphasizing factors such as capacitance, rate capability, and charge/discharge cycle performance. Hydrothermally treated MoS2-carbon exhibited a specific capacitance of approximately 150 F g-1 in supercapacitors, attributed to its high surface area and efficient charge storage mechanisms. Additionally, for Li-ion battery materials without hydrothermal treatment showed impressive capacity retention of around 88% after 500 charge-discharge cycles, starting with an initial specific capacity of about 920 mAh/g. Long-term stability was demonstrated in both supercapacitors and lithium-ion batteries, with minimal capacitance degradation even after extensive charge-discharge cycles. This research underscores the potential of MoS2-based materials as effective energy storage solutions.

Preparation of high strength and rigidity carbon layer on SiO material surface by dynamic CVD method using gas carbon source C2H2

The main issue in the application of silicon-based negative electrode materials is the inevitable volume expansion, leading to negative electrode material fracture, which severely impacts the performance of batteries. This study employed Chemical Vapor Deposition (CVD) (C2H2@SiO), solid-phase coating method (Pitch@SiO), and liquid-phase coating method (RGFQ@SiO) to coat the surface of SiO materials with a dense amorphous carbon structure. Material property analysis revealed that C2H2@SiO has a relatively small specific surface area (1.8 m2 g−1) and surface carbon increment (2.4 %). It exhibited high reversible specific capacity (1563.4 mAh g−1), high initial Coulombic efficiency (81.45 %), and low volume expansion rate (9.3 %). Mechanical performance testing indicated that the surface carbon layer Young's modulus of C2H2@SiO was the highest (35 GPa), suggesting that using the CVD method to obtain a dense carbon layer can enhance the structural strength of the material. Based on the electrochemical-mechanical coupling theory simulation analysis of the stress during the charge-discharge process of electrode materials, the evolution of concentration and stress field during lithium insertion process was obtained, showing that the coating can further improve the electrochemical and mechanical performance of the negative electrode materials effectively. Additionally, the negative electrode sheets fabricated using sample C2H2@SiO were assembled into 18650 cylindrical batteries, exhibiting excellent cycling performance in 1000 cycles at 25 °C with a capacity retention rate of 85.7 %, along with good rate capability and high/low-temperature performance. The conclusions of this study provide certain guidance for the design and optimization of negative electrode materials for battery electrodes.

Obtaining V2(PO4)3 by sodium extraction from single-phase NaxV2(PO4)3 (1 < x < 3) positive electrode materials.

We report on single-phase NaxV2(PO4)3 compositions (1.5 ≤ x ≤ 2.5) of the Na super ionic conductor type, obtained from a straightforward synthesis route. Typically, chemically prepared c-Na2V2(PO4)3, obtained by annealing an equimolar mixture of Na3V2(PO4)3 and NaV2(PO4)3, exhibits a specific sodium-ion distribution (occupancy of the Na(1) site of only 0.66(4)), whereas that of the electrochemically obtained e-Na2V2(PO4)3 (from Na3V2(PO4)3) is close to 1. Unlike conventional Na3V2(PO4)3, when used as positive electrode materials in Na-ion batteries, the NaxV2(PO4)3 compositions lead to unusual single-phase Na+ extraction/insertion mechanisms with continuous voltage changes upon Na+ extraction/insertion. We demonstrate that the average equilibrium operating voltage observed upon Na+ deintercalation from single-phase Na2V2(PO4)3 is increased up to an average value of ~3.70 V versus Na+/Na (thanks to the activation of the V4+/V5+ redox couple) compared to 3.37 V versus Na+/Na in conventional Na3V2(PO4)3, thus leading to an increase in the theoretical energy density from 396.3 Wh kg-1 to 458.1 Wh kg-1. Electrochemical and chemical Na+ deintercalation from c-Na2V2(PO4)3 enables complete Na-ion extraction, increasing energy density.

A review on progress and prospects of diatomaceous earth as a bio-template material for electrochemical energy storage: synthesis, characterization, and applications

AbstractThis comprehensive review explores the remarkable progress and prospects of diatomaceous earth (DE) as a bio-template material for synthesizing electrode materials tailored explicitly for supercapacitor and battery applications. The unique structures within DE, including its mesoporous nature and high surface area, have positioned it as a pivotal material in energy storage. The mesoporous framework of DE, often defined by pores with diameters between 2 and 50 nm, provides a substantial surface area, a fundamental element for charge storage, and transfer in electrochemical energy conversion and storage. Its bio-templating capabilities have ushered in the creation of highly efficient electrode materials. Moreover, the role of DE in enhancing ion accessibility has made it an excellent choice for high-power applications. As we gaze toward the future, the prospects of DE as a bio-template material for supercapacitor and battery electrode material appear exceptionally promising. Customized material synthesis, scalability challenges, multidisciplinary collaborations, and sustainable initiatives are emerging as key areas of interest. The natural abundance and eco-friendly attributes of DE align with the growing emphasis on sustainability in energy solutions, and its contribution to electrode material synthesis for supercapacitors and batteries presents an exciting avenue to evolve energy storage technologies. Its intricate structures and bio-templating capabilities offer a compelling path for advancing sustainable, high-performance energy storage solutions, marking a significant step toward a greener and more efficient future. Graphical Abstract

Enhanced storage performance of a low-cost hard carbon derived from biomass

Hard Carbon is the most widely used negative electrode material for sodium-ion batteries today. Achieving high storage capacity and increasing the plateau capacity, as opposed to the sloping profile, are crucial for enhancing energy density of the full cells. While several publications address the synthesis of hard carbon, the economic viability for commercial scale-up hinges on the choice of precursors. In this study, we report the electrochemical properties of hard carbon derived from two biomass precursors, sugarcane waste (bagasse) and corn waste, and compare their performances with commercially available hard carbon. The hard carbon derived from bagasse delivers a capacity of 307 mAh/g at C/10 rate and retains approximately 234 mAh/g at 3C discharge rate. We integrate surface area, pore size distribution, Raman spectroscopy, small-angle X-ray and neutron scattering data to elucidate the sodium storage mechanism in these hard carbon samples. Correlated graphitic domains with hexagonal ordering along with fractal like agglomeration of the nanosheets are quantified. The high plateau capacity of the bagasse-derived hard carbon is attributed to the characteristic morphology and size distribution of the nanosheets and their nature of agglomeration.

Organometallic Polymer Constructed by Active Fe-C12N8 Centers for Boosting Sodium-Ion Storage.

Organic-metal coordination materials with rich structural diversity are considered as promising electrode materials for rechargeable sodium-ion batteries. However, the electrochemical performance can be constrained by the limited number of active sites and structural instability under the discharge/charge process. Herein, organometallic polymer microspheres (Fe-PDA-220) with a unique d-π conjugated structure was designed and successfully constructed through a simple synchronous polymerization and coordination reactions. Polymerization of phenylenediamine was initiated by Fe3+ and Fe2+ ions generated synchronously during the polymerization integrated with poly-aminoquinone chains to form Fe-C12N8 active centers. Used as electrode materials for sodium-ion batteries, the distinctive Fe-C bond significantly boosts the structural stability, and the π-d conjugation system could facilitate electron transfer. A high reversible capacity of 345 mAh g-1 was delivered at 0.1 A g-1 and a capacity of 106 mAh g-1 was maintained even after discharged/charged at 1.0 A g-1 for 5000 cycles, outperforming most reported coordination materials. Spectroscopic and electronic analyses revealed that a two-electron reaction occurred per active unit, accompanied by the reversible redox evolution of the C=N groups and Fe ions during the sodiation/desodiation. This work provides a promising and efficient strategy for boosting the electrochemical performance of organic electrode materials by the design of organometallic polymers.

Recent Advancements of Graphene and Some Selected Graphene-Based Electrode Materials for Lithium-Ion Battery

Graphene is a two-dimensional monolayer of carbon atoms arranged in a hexagonal lattice consisting of sp2 hybridized conjugated carbon atoms and serves as a promising electrode material for lithium-ion batteries (LIBs) owing to its superior properties, including a high specific surface area (2630 m2g-1), a high theoretical capacity (744 mAhg-1), excellent electrical conductivity, and a wide electrochemical potential window. Despite having these superior properties, the restacking as well as the van der Waals forces of attraction among the graphene layers and the long path for Li-ion diffusion are factors that reduce the specific surface area and active site for Li-ion storage, which in turn influence the electrochemical performance of LIBs. The functionalization of graphene to porous graphene, graphene quantum dots, and graphene oxides, as well as the integration of graphene with other foreign materials such as transitional metal oxides, various heteroatoms (boron, nitrogen, sulfur, etc.), and covalent organic frameworks (COF), are the two main strategies that have been widely applied to improve the properties of graphene for Li-ion battery applications. In this review, recent works regarding the performance of graphene and graphenebased electrode materials for LIBs applications were reviewed and presented in detail. Moreover, various graphene fabrication techniques in terms of quality and quantity of graphene produced as well as the future overview of graphene and some selected graphene-based materials for LIBs applications have been assessed and summarized.

Exploring the potential of two-dimensional MB4 (M=Cr, Mo, and W) monolayer as a high-capacity negative electrode material for Al-ion batteries

Rechargeable metal-ion batteries can employ two-dimensional transition metal tetraboride monolayers because of their numerous accommodating sites, high specific surface area, and layered structure. Li-ion batteries (LIBs) can be efficiently replaced by aluminum ion batteries (AIBs) because aluminum is a cheap and abundant resource. In this work, the density functional theory approach has been used for Al-ion batteries to predict MB4(M= Cr, Mo, W) monolayers performance as anode material. We analyze these monolayers' structures, which are mechanically, thermally, and dynamically stable. Utilizing the energy-efficient adsorption of six Al-atom layers and their lightweight properties, with large storage capacities of 5066 mA h g−1, 3466 mA h g−1, and 2124 mA h g−1, with relatively low average open circuit voltages of 0.18 V, 0.15 V, and 0.11 V for CrB4, MoB4, and WB4, respectively, these monolayers show significant superiority over other 2D anode materials. Likewise, MB4 monolayer showed faster Al ion mobility as seen by the low activation barriers of 0.95 eV, 0.83 eV, and 0.49 eV for CrB4, MoB4, and WB4, respectively. Additionally, even after the full content of Al ions was adsorbed, the metallic characteristics of the materials were mostly retained. These traits suggest that monolayer CrB4, MoB4, and WB4 are promising anode materials for AIBs, with impressive rate capacities.