Electrochemiluminescence Research Articles

Simple hydrated electron-induced electrochemiluminescence determination of alkaline phosphatase with novel time-resolved internal standard strategy at boron doped diamond electrodes

Hydrated electrons were generated at boron doped diamond electrodes in fully aqueous solutions during cathodic pulse polarization and utilized for the electrochemiluminescence (ECL) determination of alkaline phosphatase (ALP) by adapting one of the most common fluorescent methods. In this approach, highly fluorescent 4-methylumbelliferyl (MU) is enzymatically generated from non-fluorescent 4-methylumbelliferyl phosphate (MUP) substrate and chemically excited in the presence of oxidizing radicals and reducing hydrated electrons. A novel time-resolved internal standard strategy is presented to counter matrix effects to certain degree and to lower signal variation among concurrent measurements. In this unique approach, the cathodic ECL signals of MU and Tb(III)-chelate were separated on the basis of their exceptionally different excited state lifetimes. This enabled more precise determination of ALP by simply measuring the ratio of ECL emissions during and after cathodic excitation pulse with simple two-electrode, single photomultiplier tube setup. The ratiometric ECL signals in the absence and presence of 1.0 % serum (v/v) were interchangeable whereas ratiometric signal recovery in the presence of 10.0 % serum was ∼85 %.

Highly Electroactive Co2+-Based Metal-Organic Frameworks as an Efficient Coreaction Accelerator for Amplifying Near-Infrared Electrochemiluminescence of Gold Nanoclusters in Biomarkers Immunoassay.

Metal nanoclusters (NCs) as a new kind of luminophore have acquired sufficient interest, but their widespread application is restricted on account of their relatively low electrochemiluminescence (ECL) efficiency. Then, aqueous metal NCs with high ECL efficiency were strongly anticipated, especially for the ultrasensitive analysis of biomarkers. Herein, a near-infrared (NIR) ECL biosensing strategy for the test of neuron-specific enolase (NSE) was proposed by utilizing N-acetyl-l-cysteine (NAC)- and cysteamine (Cys)-stabilized gold NCs (NAC/Cys-AuNCs) as ECL emitters with the NIR ECL emission around 860 nm and a metal-organic framework/palladium nanocubes (ZIF-67/PdNCs) hybrid as the coreaction accelerator through their admirable electrocatalytic activity. The NIR emission would reduce photochemical injury to the samples and even realize nondestructive analysis with highly strong susceptibility and suitability. Furthermore, the utilization of ZIF-67/PdNCs could improve the ECL response of NAC/Cys-AuNCs by facilitating the oxidation of the coreactant triethylamine (TEA), leading to the production of a larger quantity of reducing intermediate radical TEA•+. Consequently, NAC/Cys-AuNCs with ZIF-67/PdNCs displayed 2.7 fold enhanced ECL emission compared with the single NAC/Cys-AuNCs using TEA as the coreactant. In addition, HWRGWVC (HWR), a heptapeptide, was introduced to immobilize antibodies for the specially binding Fc fragment of the antibodies, which improved the binding efficiency and sensitivity. As a result, a "signal-on" immunosensor for NSE analysis was obtained with an extensive linear range of 0.1 to 5 ng/mL and a low limit of detection (0.033 fg/mL) (S/N = 3). This study provides a wonderful method for the development of an efficient nondestructive immunoassay.

Novel Nucleic Acid-Assisted Ion-Responsive ECL Biosensor Based on Hollow AuAg Nanoboxes with Excellent SPR and Effective Coreaction Acceleration.

Novel hollow AuAg nanoboxes (AuAg NBs) were designed for an innovative electrochemiluminescence (ECL) sensor to ultrasensitively detect Pb2+ and Hg2+ with the aid of DNAzyme and "thymine-Hg2+-thymine" ("T-Hg2+-T") structure. AuAg NBs are employed as an excellent surface plasma resonance (SPR) source, as well as an effective coreaction accelerator for the CoNi NFs/S2O82- system to greatly improve ECL performance. To detect Pb2+, the DNAzyme catalyzes the cleavage of ribonucleic acid targets into numerous small nucleic acid fragments, leading to an ECL signal. When Hg2+ is added, the thymine-thymine (T-T) mismatches of the Hg2+ aptamer bind Hg2+ to form the "T-Hg2+-T" structure, which not only inhibits the SPR process but also produces a large steric hindrance, thus quenching the ECL signal and allowing quantification of Hg2+. The novel ECL sensor quantifies Pb2+ in the range of 0.1 fM to 0.1 μM with a limit of detection of 0.07 fM and Hg2+ in the range of 10 pM to 1 μM with a LOD of 4.07 pM.

Pyrenetetrasulfonate-grafted 2D ultrathin metal–organic layer as new electrochemiluminescence emitters for ultrasensitive microRNA-21 assay

The exploration of novel electrochemiluminescence (ECL) luminophores with excellent ECL properties is a current research hotspot in the ECL field. Herein, a novel high-efficiency Ru-complex-free ECL emitter PyTS-Zr-BTB-MOL has been prepared by using porous ultrathin Zr-BTB metal–organic layer (MOL) as carrier to coordinatively graft the cheap and easily available polycyclic aromatic hydrocarbon (PAH) derivative luminophore PyTS whose ECL performance has never been investigated. Gratifyingly, the ECL intensity and efficiency of PyTS-Zr-BTB-MOL were markedly enhanced compared to both PyTS monomers and PyTS aggregates. The main reason was that the distance between pyrene rings was greatly expanded after the PyTS grafting on the Zr6 clusters of Zr-BTB-MOL, which overcame the aggregation-caused quenching (ACQ) effect of PyTS and thus enhanced the ECL emission. Meanwhile, the porous nanosheet structure of PyTS-Zr-BTB-MOL could distinctly increase the exposure of PyTS luminophores and shorten the diffusion paths of coreactants and electrons/ions, which effectively promoted the electrochemical excitation of more PyTS luminophores and thus achieved a further ECL enhancement. In light of the remarkable ECL property of PyTS-Zr-BTB-MOL, it was employed as an ECL indicator to build a novel high-sensitivity ECL biosensor for microRNA-21 determination, possessing a satisfactory response range (100 aM to 100 pM) and an ultralow detection limit (10.4 aM). Overall, this work demonstrated that using MOLs to coordinatively graft the PAH derivative luminophores to eliminate the ACQ effect and increase the utilization rate of the luminophores is a promising and efficient strategy to develop high-performance Ru-complex-free ECL materials for assembling ultrasensitive ECL biosensing platforms.

Automatic Electrochemiluminescence Method for the Detection of Cancerous Exosomes Incorporating Specific Aptamer-Magnetic Beads and Signal Nanoprobes.

Exosomes, as an emerging biomarker, have exhibited remarkable promise in early cancer diagnosis. Here, a highly sensitive, selective, and automatic electrochemiluminescence (ECL) method for the detection of cancerous exosomes was developed. Specific aptamer-(EK)4 peptide-tagged magnetic beads (MBs-(EK)4-aptamer) were designed as a magnetic capture probe in which the (EK)4 peptide was used to reduce the steric binding hindrance of cancerous exosomes with a specific aptamer. One new universal ECL signal nanoprobe (CD9 Ab-PEG@SiO2ϵRu(bpy)32+) was designed and synthesized by using microporous SiO2 nanoparticles as the carrier for loading ECL reagent Ru(bpy)32+, polyethylene glycol (PEG) layer, and anticluster of differentiation 9 antibody (CD9 Ab). A "sandwich" biocomplex was formed on the surface of the magnetic capture probe after mixing the capture probe, target exosomes, and ECL signal nanoprobe, and then it was introduced into an automated ECL analyzer for rapid and automatic ECL measurement. It was found that the designed signal nanoprobe shows a 270-fold improvement in the signal-to-noise ratio than that of the ruthenium complex-labeled CD9 antibody signal probe. The relative ECL intensity was proportional to MCF-7 exosomes as a model in the range of 102 to 104 particle/μL, with a detection limit of 11 particle/μL. Furthermore, the ECL method was employed to discriminate cancerous exosomes based on fingerprint responses using the designed multiple magnetic capture probes and the universal ECL signal nanoprobe. This work demonstrates that the utilization of a designed automated ECL tactic using the MBs-(EK)4-aptamer capture probe and the CD9 Ab-PEG@SiO2ϵRu(bpy)32+ signal nanoprobe will provide a unique and robust method for the detection and discrimination of cancerous exosomes.

A novel electropolymerized molecularly imprinted dual-mode sensor for bisphenol AF detection in pond mud

Recently, bisphenol AF (BPAF) as most commonly used bisphenol A analogs had the increasing higher level in the environment with unknown risks. Herein, a synchronous dual-mode sensor had been established based on differential pulse voltammetry (DPV) and electrochemiluminescence (ECL) for the detection of BPAF in pond mud. Firstly, the sensing molecularly imprinted polymer (MIP) films were prepared by electrochemical polymerization procedure with 3,4-ethoxylene dioxy thiophene (EDOT) as the functional monomer, BPAF as the template molecule and MXene as the supporting electrolyte. Due to unique characters of PEDOT and MXene, the constructed MIP films were stable and highly conductive. Meanwhile, zinc-doped bismuth sulfide quantum dots (Zn-Bi2S3 QDs) were synthesized as a nano-emitter to generate strong ECL signals in the MIP film. In the sensing process, a pulsed voltage applied to the PEDOT/MXene MIP film to generate both DPV and ECL signals for simultaneous dual-mode detection. Additionally, the liquid-liquid extraction with deep eutectic solvent (menthol: octanol 1:1) was used for the pre-concentration of the BPAF in the pond mud. Based on the sensing system, the ECL and DPV response showed the good linear relationships with the concentration of BPAF with the ranges of 0.01 μM–50 μM and 0.1 μM–50 μM and the detection limits of 0.0060 μM and 0.059 μM, respectively.

Flexible and Dynamic Light-Guided Electrochemiluminescence for Spatiotemporal Imaging of Photoelectrochemical Processes on Hematite.

Here, we report an electrochemiluminescence (ECL)-based approach for imaging of local photoelectrochemical processes on hematite in a spatially and temporally controlled manner. The local processes were guided by flexible and dynamic light illumination, not requiring any prepatterned conductive features or photomasks, with a digital micromirror device (DMD). The imaging approach was based on light-addressable electrochemical reactions on hematite, resulting in photoinduced ECL emission for spatiotemporally resolved imaging of photoelectrochemical processes selectively guided by light illumination. After clarifying the capability of hematite as a photosensitive electrode, we validated that the illuminated hematite exhibited stable light-guided ECL emission in correspondence with the illuminated area, with a spatial resolution of 0.8 μm and a temporal resolution of 1 μs, even over a long period of 6 h. More importantly, this study exemplified the simple yet effective ECL-based approach for electrochemical visualization of local photoelectrochemical processes guided by flexible and dynamic adjustment of light illumination in a spatiotemporally controlled way.

Discovering Facet-Dependent Formation Kinetics of Key Intermediates in Electrochemical Ammonia Oxidation by a Electrochemiluminescence Active Probe.

Facile evaluation of formation kinetics of key intermediate is crucial for a comprehensive understanding of electrochemical ammonia oxidation reaction (AOR) mechanisms and the design of efficient electrocatalysts. Currently, elucidating the formation kinetics of key intermediate associated with rate-determining step is still challenging. Herein, 4-phtalamide-N-(4'-methylcoumarin) naphthalimide (CF) is developed as a molecular probe to detect N2H4 intermediate during AOR via electrochemiluminescence (ECL) and further investigated the formation kinetics of N2H4 on Pt catalysts with different crystal planes. CF probe can selectively react with N2H4 to release ECL substance luminol. Thus, N2H4 intermediate as a key intermediate can be sensitively and selectively detected by ECL during AOR. For the first time, Pt(100) facet is discovered to exhibit faster N2H4 formation kinetics than Pt(111) facet, which is further confirmed by Density functional theory calculation and the finite element simulation. The AOR mechanism under the framework of Gerischer and Mauerer is further validated by examining N2H4 formation kinetics during the dimerization process (NH2 coupling). The developed ECL active probe and the discovered facet-dependent formation kinetics of key intermediates provide a promising new tool and strategy for the understanding of electrochemical AOR mechanisms and the design of efficient electrocatalysts.

A dual-mode biosensor based on CdIn2S4 hollow microsphere combined with Au@CuO/Cu2O nanozyme for sensitive detection of Sa-16S rDNA

A dual-mode biosensor used CdIn2S4 hollow microspheres as electrochemiluminescence (ECL) and photoelectrochemistry (PEC) dual signal probes combined with Au@CuO/Cu2O nano-enzyme catalysis was fabricated for sensitive detection of Sa-16S rDNA. Firstly, CdIn2S4 microspheres displayed excellent ECL and PEC signals, then the target Sa-16S rDNA introduced a large number of Au@CuO/Cu2O nanoparticles to the electrode via Exo-III amplification strategy. Au@CuO/Cu2O is a highly efficient peroxidase mimicase, and can effectively promote H2O2 to produce ·OH, which further oxidized 4-chloro-1-naphthol (4-CN) to produce a large amount of insoluble precipitate on the electrode surface, then significantly reduced the PEC and ECL signals of CdIn2S4 for target detection. This study opens up a new multifunctional photoelectric microspheres and a flexible biosensor by using CdIn2S4 and nanozymes, showing a new channel for the detection of DNA molecules and providing valuable insights for the development of PEC biosensing technologies based on nanozymes.

Metal-Organic framework incorporated luminescent PTCA combined with novel co-reactant accelerator for ultra-sensitive electrochemiluminescence detection of CA19-9

Polycyclic aromatic hydrocarbons (PAHs) are commonly used as electrochemiluminescence (ECL) luminophores. However, PAHs are limited by the aggregation-caused quenching (ACQ) effect, which reduces ECL emission. Therefore, developing an ECL system from PAHs with efficient luminescence is a significant challenge. In this work, a two-ligand strategy was proposed to assemble 3, 4, 9, 10-perylenetetracarboxylic acid (PTCA) into zeolitic imidazole framework-8 (ZIF-8). The ACQ effect of PTCA was inhibited by participating in the formation of metal–organic frameworks (MOFs) and a luminescent ZIF-8-PTC (Z8P) composite was obtained. Satisfactorily, conceptual experiments demonstrated that the significantly higher ECL efficiency of Z8P was achieved compared with PTCA monomers and aggregates. On the sensing substrate, a novel co-reactant accelerator (Au@MFNC) was used to achieve continuous catalysis of the persulfate (K2S2O8) with the Prussian blue analogues (PBAs) as a template under the efficient synergistic effect of MoS2. Through the reversible transformation of the transition metal valence states, a sufficient amount of sulfate radicals (SO4•−), again amplifying the ECL signal of Pd@Z8P. Under ideal conditions, the constructed dual-MOFs ECL immunosensor had a wide response range (1 × 10−4 − 1 × 102 U/mL) and a low limit of detection (LOD) (6 × 10−5 U/mL), which provided an alternative method for CA19-9 ultrasensitive detection, and broadened a new idea for the development of high-performance luminescent MOFs.

Recent Advances in Electrochemiluminescence Visual Biosensing and Bioimaging.

Electrochemiluminescence (ECL) is one of the most powerful techniques that meet the needs of analysis and detection in a variety of scenarios, because of its highly analytical sensitivity and excellent spatiotemporal controllability. ECL combined with microscopy (ECLM) offers a promising approach for quantifying and mapping a wide range of analytes. To date, ECLM has been widely used to image biological entities and processes, such as cells, subcellular structures, proteins and membrane transport properties. In this review, we first introduced the mechanisms of several classic ECL systems, then highlighted the progress of visual biosensing and bioimaging by ECLM in the last decade. Finally, the characteristics of ECLM were summarized, as well as some of the current challenges. The future research interests and potential directions for the application of ECLM were also outlooked.

Electrochemiluminescence Sensor Based on TPEA‐RuMOF: For Highly Selective and Sensitive Detection of Copper Ions

AbstractIn this study, we present the novel combination of AE‐TPEA with RuMOF to construct an electrochemiluminescence (ECL) sensor using a TPEA‐RuMOF composite material specifically for copper ions (Cu2+) detection. Using K2S2O8 as a co‐reactant, we explored the ECL behavior of the TPEA‐RuMOF modified electrode, enabling the quantitative detection of Cu2+. Remarkably, this sensor exhibited a wide linear range from 1×10−5 to 1×10−9 M (R2=0.998) and boasted a detection limit as low as 0.41 nM, which is considerably below the EPA (Environmental Protection Agency) permissible copper ion concentration in drinking water of <1.3 mg/L. our synthesized probe offers enhanced stability and selectivity in copper ion detection. This indicates its considerable potential for high‐performance copper ion detectors. We further validated the analytical applicability of this sensor using river water samples.

Dual-Ligand Ruthenium Coordination Polymer-Derived Self-Enhanced Electrochemiluminescent Emitters for Sensitive Detection of Procalcitonin.

Ru-based electrochemiluminescence (ECL) coordination polymers are widely employed for bioanalysis and medical diagnosis. However, commonly used Ru-based coordination polymers face the limitation of low efficiency due to the long distance between the ECL reagent and the coreactant dispersed in detecting solution. Herein, we report a dual-ligand self-enhanced ECL coordination polymer, composed of tris(4,4'-dicarboxylic acid-2,2'-bipyridyl) ruthenium(II) dichloride (Ru(dcbpy)32+) as ECL reactant ligand and ethylenediamine (EDA) as corresponding coreactant ligand into Zn2+ metal node, termed Zn-Ru-EDA. Zn-Ru-EDA shows excellent ECL performance which is attributed to the effective intramolecular electron transport between the two ligands. Furthermore, the dual-ligand polymer allows an anodic low excitation potential (+1.09 V) luminescence. The shift in the energy level of the highest occupied molecular orbital (HOMO) upward after the synthesis of the Zn-Ru-EDA has resulted in a reduced excitation potential. The low excitation potential reduced biomolecular damage and the destruction of the modified electrodes. The ECL biosensor has been constructed using Zn-Ru-EDA with high ECL efficiency for the ultrasensitive detection of a bacterial infection and sepsis biomarker, procalcitonin (PCT), in the range from 1.00 × 10-6 to 1.00 × 10 ng·mL-1 with outstanding selectivity, and the detection limit was as low as 0.47 fg·mL-1. Collectively, the dual-ligand-based self-enhanced polymer may provide an ideal strategy for high ECL efficiency improvement as well as designing new self-enhanced multiple-ligand-based coordination in sensitive biomolecular detection for early disease diagnostics.

Stable detection of diazinon residues in vegetables by an electrochemiluminescent aptasensor based on the in-situ production of H2O2 from dual-catalytic glucose

Stable detection of diazinon (DZN) residues in vegetables is important for food safety. In this work, an electrochemiluminescence (ECL) aptasensor with dual-catalytic glucose in-situ production of H2O2 was constructed for the stable detection of DZN in vegetables. Firstly, MWCNTs@MB was prepared using π-π stacking interactions between methylene blue (MB) and multi-walled carbon nanotubes (MWCNTs) to enhance the loading of MB on an electrode and thus catalyze the generation of H2O2 from glucose. Secondly, Cu2O@AuNPs was formed by loading AuNPs on the surface of Cu2O through spontaneous reduction reaction, which improved the interfacial charge transfer, Cu2O nano-enzyme had glucose oxidase mimicking activity and could further catalyze the production of more H2O2 from glucose. MWCNTs@MB and Cu2O@AuNPs played a key role in the in-situ generation of co-reacting reagent H2O2, which solved the problem of unstable detection caused by the easy decomposition of the H2O2 solution added to the luminescence system. In addition, the aptamer was immobilized on the electrode surface by forming Au–S bonds with Cu2O@AuNPs. As a result, the ECL aptasensor performed good linearity in 1.00 pg mL−1-1.00 μg mL−1 and a low limit of detection (LOD) to 0.39 pg mL−1 (S/N = 3). This work provided an effective method for the accurate and stable detection of DZN residues in vegetables, which was of great significance in ensuring food safety and assessing the environmental risk of DZN.

Detection of urokinase based on ECL resonance energy transfer between block copolymers encapsulated iridium complex and ReS2 nanosheets

The encapsulation of water insoluble iridium complex in SiO2 nanoparticles can be used to fabricate aqueous electrochemiluminescence (ECL) sensor, however, the ECL signal is greatly reduced. It is urgent to explore more suitable method to encapsulate iridium complex and improve its ECL efficiency. Pluronic block copolymers has good biocompatibility and high load capacity, which might be used to encapsulate iridium complex. In the present work, one kind of concentric nanospheres were assembled by encapsulating iridium complexes into block copolymers using poly (styrene-co-maleicanhydride) (PSMA@Ir). Strong anodic ECL signal was obtained at PSMA@Ir nanospheres modified electrode without additional coreactant. The light absorption character of ReS2 nanosheets (ReS2NS) endowed it the ability to accept energy from PSMA@Ir ECL. As a result, a novel ECL resonance energy transfer (ECL-RET) system was constructed with PSMA@Ir as energy donor while ReS2NS as energy acceptor. Based on the above results, an ECL aptasensor was designed to detect urokinase (UPA). The ECL intensity changed linearly with the logarithm of UPA concentration in the range of 1.0 × 10−16–1.0 × 10−12 mol/L with a detection limit of 2.95 × 10−17 mol/L. The prepared sensor owned high sensitivity and selectivity, and provided new avenue for the application of water insoluble iridium complex in ECL sensing.

Strategies and trends in the amplification of electrochemiluminescence signals for biosensing

This article offers a thorough summary of recent studies on the amplification of electrochemiluminescence (ECL) signals in biosensing applications using nanomaterials, enzymes, rolling circle amplifications (RCA), hybridization chain reaction (HCR), DNA-mediated amplification, and nanozymes. Recent developments on the influence of nanoparticles on ECL properties were covered in this review. Defect, valence state, shape, surface ligand, and the spatial distribution of the composition of the nanomaterial are examples of the microstructures of nanomaterials. The review aims to illustrate how the features of ECL signal amplification for biosensing are related to the microstructures of nanomaterials. It also discusses different enzymatic (allosteric and entrasteric) methods for amplifying ECL signals. Nucleic acids are suitable for the robust creation of nanostructures due to their programmed self-assembly and intrinsic diverse selective molecular recognition. By virtue of their distinctive structures and structural feature these are considered as promising candidates as ECL signal amplifiers.

Electrochemiluminescence Microscopy.

Electrochemiluminescence (ECL) is rapidly evolving from an analytical method into an optical microscopy. The orthogonality of the electrochemical trigger and the optical readout distinguishes it from classic microscopy and electrochemical techniques, owing to its near-zero background, remarkable sensitivity, and absence of photobleaching and phototoxicity. In this minireview, we summarize the recent advances in ECL imaging technology, emphasizing original configurations which enable the imaging of biological entities and the improvement of the analytical properties by increasing the complexity and multiplexing of bioassays. Additionally, mapping the (electro)chemical reactivity in space provides valuable information on nanomaterials and facilitates deciphering ECL mechanisms for improving their performances in diagnostics and (electro)catalysis. Finally, we highlight the recent achievements in imaging at the ultimate limits of single molecules, single photons or single chemical reactions, and the current challenges to translate the ECL imaging advances to other fields such as material science, catalysis and biology.

A randomized phase 1/2a trial of ExPEC10V vaccine in adults with a history of UTI

The safety, reactogenicity, and immunogenicity of 3 doses of ExPEC10V (VAC52416), a vaccine candidate to prevent invasive Escherichia coli disease, were assessed in a phase 1/2a study (NCT03819049). In Cohort 1, ExPEC10V was well tolerated; the high dose was selected as optimal and further characterized in Cohort 2. Cohort 2 comprised a maximum 28-day screening, vaccination (Day 1), double-blind 181-day follow-up, and open-label long-term follow-up until Year 1. Healthy participants (≥60 years) with a history of urinary tract infection (UTI) within 5 years were randomized to receive ExPEC10V or placebo. The primary endpoint evaluated the safety and reactogenicity of ExPEC10V (solicited local and systemic AEs [until Day 15]; unsolicited AEs [until Day 30], SAEs [until Day 181], and immunogenicity [Day 30]) via multiplex electrochemiluminescent (ECL) and multiplex opsonophagocytic assay (MOPA). 416 participants (ExPEC10V, n = 278; placebo, n = 138) were included (mean age [SD], 68.8 [6.52] years; female, 79.6%; White, 96.1%). The incidence of solicited AEs was higher with ExPEC10V (local, 50.0% [n = 139]; systemic, 50.0% [n = 139]) than placebo (15.9% [n = 22]; 38.4% [n = 53]); rates of unsolicited AEs were comparable (ExPEC10V, 28.4% [n = 79]; placebo, 26.1% [n = 36]). No vaccine-related SAEs or deaths were reported. ExPEC10V elicited a robust antibody-mediated immunogenic response across all serotypes with ECL (Day 30 geometric mean fold increase, 2.33–8.18) and demonstrated functional opsonophagocytic killing activity across all measured serotypes (Day 30 geometric mean fold increase, 1.81–9.68). ExPEC10V exhibited an acceptable safety profile and a robust vaccine-induced functional immunogenic response in participants with a history of UTI. Clinical trial registration details: https://clinicaltrials.gov/study/NCT03819049.

Electrochemiluminescence enhanced by molecular engineering linear π-conjugated polymer: An ingenious ECL emitter for the construction of exosome sensing platform

Linear π-conjugated polymers (LCPs) with π-electron conjugation system have many remarkable optical characteristics such as fluorescence and electrochemiluminescence (ECL). However, the extremely strong interchain interaction and π-π stacking limit the luminescence efficiency. In this work, 1H-1,2,4-triazole-3,5-diamine was chosen as the polymer monomer and reacted with terephthalaldehyde via simple Schiff base condensation to synthesize LCPs. Subsequently, molecular engineering strategy was adopted to construct zirconium-based LCPs (MLCPs), which not only prevented π-π stacking but also ensured that extended π-coupling was maintained in the LCPs, thus effectively promoting charge transport and achieving strong luminescence. Second, the coreactant polyethyleneimine (PEI) was assembled onto the MLCPs (MLCPs@PEI) to further promote the emission of ECL. To further explore the potential of the obtained MLCPs@PEI as emerging ECL emitter, colorectal cancer exosome was chosen as model biomarker, and an innovative ECL ratiometric system based on MLCPs@PEI and luminol was designed to improve the validity and accuracy of the sensors. This research provides a fresh nanoplatform for exosome detection and broadens the application of LCPs in ECL immunoassay.

Eu-doped chitosan carbon dot/dendritic silver nanostructure-based biosensor for BRAF detection in thyroid cancer exosome

In this work, a novel electrochemiluminescence (ECL) biosensor has been constructed with Eu-doped chitosan carbon dot (Eu: Cs dot) and dendritic silver nanostructure. Firstly, Eu: Cs dots were synthesized as ECL tags, which not only possessed exceptional electrochemical characters and intense luminescence, but also can reacted with H2O2 as co-reactant to generate ECL signal. Furthermore, dendritic silver nanostructure with conductive gel was successfully prepared as sensing interface. The dendritic silver nanostructure with conductive gel displayed the ideal conductivity, good electrochemical stability, which can enhance the ECL intensity of Eu: CS dots. Finally, BRAF V600E from thyroid cancer exosome in the clinic eluate can be captured and detected. The results indicated the relative association between BRAF V600E mutation and lymphatic metastasis, which can be used in assessing thyroid cancer progression for advancing clinical diagnosis applications.