Electrical Properties Research Articles

Enhanced Activation in Phosphorous-Doped Silicon via Dual-Beam Laser Annealing

In this study, we conduct a comparative analysis of single-beam laser annealing (SBLA) and dual-beam laser annealing (DBLA) techniques for semiconductor manufacturing. In the DBLA approach, two laser beams were precisely aligned to simultaneously heat a phosphorus-doped silicon (Si) wafer. The main objective was to investigate the impact of the two annealing techniques on the electrical properties, crystalline structure, and diffusion profile of the treated phosphorus-doped Si at equivalent laser powers. Both SBLA and DBLA improved the electrical properties of the phosphorus-doped Si, evidenced by increased carrier concentration and reduced carrier mobility. Additionally, the crystalline structure of the phosphorus-doped Si showed favorable modifications, with no defects and improved crystallinity. While both SBLA and DBLA produced similar phosphorus profiles with no significant redistribution of dopants compared to the as-implanted sample, DBLA achieved a higher activation ratio than SBLA. Although the results suggest improved dopant activation with minimal diffusion, further studies are needed to clearly confirm the effect of DBLA on dopant activation and diffusion.

Electrical Properties and Reliability of AlGaN/GaN High Electron Mobility Transistor under RF Overdrive Stress at High Temperature

Electrical Properties and Reliability of AlGaN/GaN High Electron Mobility Transistor under RF Overdrive Stress at High Temperature

Impact of Structural Alterations from Chemical Doping on the Electrical Transport Properties of Conjugated Polymers

Impact of Structural Alterations from Chemical Doping on the Electrical Transport Properties of Conjugated Polymers

Investigating the optical and electrical performance of rod coated silver nanowire-based transparent conducting films

Silver nanowires (Ag NWs) are highly promising building blocks for developing transparent conducting films (TCFs) due to their high electrical conductivity and good optical transparency. The large-scale production of Ag NW-based high-quality TCFs using low-cost processing methods can replace the traditional oxide based TCFs. Therefore, developing a reliable technique for large-scale fabrication of Ag NW-based TCFs is vital. This work involves the synthesis of Ag NWs, the fabrication of large-area Ag NW-based TCFs using a simple rod coating process, its optimization, and the performance analysis of the fabricated TCFs, including their demonstration as transparent heaters. The polyol synthesis method produces Ag NWs of lengths ranging from 25-110µm and diameters from 80-180 nm. The effect of Ag NW length, the number of coating passes, and the volume of the NW dispersion used per coating pass on the electrical and optical properties of the TCFs are studied by quantifying sheet resistance(Rs)and transmittance (T) of the film. The performance of the fabricated film is evaluated by estimating the figure of merit (FoM) in both percolative and bulk regimes. The TCF made with NWs of length 25.7µm and diameter 85.1 nm had the largest value of bulk FoM (101.3), percolative FoM (43.9), and, conductivity exponent (0.6). This elucidated the superior performance of the fabricated TCFs over those fabricated by other techniques. The critical thickness of the film (tmin), at the crossover between the percolation and bulk, scales with the shortest dimension of the NW, namely its diameter. The percolative FoM showed an increase, with a decrease in both sheet resistance and diameter of the NWs, with lowern. The fabricated TCF is tested as a transparent heater and the demonstration proves that rod coated Ag NW-based TCFs can be used for transparent electrode applications.

Effect of compositional modification of (NixCoyMn3−x–y) O4 on electrical properties for the application to temperature sensor

Effect of compositional modification of (NixCoyMn3−x–y) O4 on electrical properties for the application to temperature sensor

Carbon fiber and PVA fiber reinforced concrete: Electrical resistivity and piezoresistive properties

This study examines the effects of carbon fiber (CF) and polyvinyl alcohol fiber (PVAF) on the mechanical and electrical properties of fiber-reinforced concrete by using four-electrode system and piezoresistive testing platforms. The optimal combination of 0.6 % CF and 0.6 % PVAF significantly improved piezoresistive properties, with a 45 % increase in relative resistivity. Additionally, 0.6 % CF with 0.9 % PVAF achieved a 13 % boost in compressive strength. SEM analysis revealed enhanced interfacial bonding between fibers, leading to improved mechanical and electrical performance. These findings highlight the composite’s potential for structural health monitoring, electromagnetic shielding, and winter snow removal applications

Simulation of synaptic properties of ferroelectric memory capacitors and neural network applications

In this work, the electrical properties and synaptic characteristics of hafnium oxide-based ferroelectric memory capacitor with metal - ferroelectric layer - metal (MFM) structure were simulated using TCAD (technology computer aided design) software. Based on the synaptic potentiation/depression characteristics of the simulated memory capacitor, a multilayer perceptron (MLP) network was constructed, and the recognition accuracy and convergence speed of the MLP network in the MNIST recognition task were simulated, and the feasibility of the ferroelectric memory capacitor synaptic device for real neural network operation was analyzed. The results show that the recognition accuracy of the MLP network reaches 93% and stabilizes after 50 iterations of training, and the recognition accuracy of the MLP network is already at a high usable level after a smaller number of training times of 20, which suggests that the synaptic plasticity of the ferroelectric memory capacitor has a good potential for the practical application of the weight updating of the MLP network.

Nanoscale Graded Nitrogen-Doping of TiO2 via Pulsed Laser Deposition for Enhancing Charge Transfer in Perovskite Solar Cells.

An electron transport layer (ETL) for highly efficient perovskite solar cells (PSCs) should exhibit superior electrical transport properties and have its band levels aligned with interfacing layers to ensure efficient extraction of photo-generated carriers. Nitrogen-doped TiO2 (TiO2:N) is considered a promising ETL because it offers higher electrical conductivity compared to conventional ETLs made from spray-pyrolyzed TiO2. However, the application of highly doped TiO2:N in PSCs is often limited by the misalignment of energy band levels with adjacent layers and reduced optical transparency. In this study, a novel approach is introduced to enhance the charge transport characteristics and accurately align the electronic band alignment of TiO2:N layer through nanoscale doping level grading, achieved through the pulsed laser deposition (PLD) technique. The TiO2:N ETL with a graded doping profile can combine characteristics of both highly doped and lightly doped phases on each side. Furthermore, a nanoscale doping gradation, employing an ultrathin sub-layer structure with graded doping levels, creates a smoothly cascading band-level alignment that bridges the adjacent layers, enhancing the transport of photo-generated carriers. Consequently, this method leads to a substantial increase in the power conversion efficiency (PCE), exceeding 22%, which represents a relative improvement of 11% compared to traditional spray-pyrolyzed TiO2-based PSCs.

Photocatalysis and microwave absorption performance of cobalt particles dispersed on activated carbon surface under the role of surface, optical, and magnetic properties

Ensuring the availability of clean water and solve electromagnetic interference are a fundamental action to support a better life. Here, the bifunctional material as photocatalyst and absorber microwave were prepared from activated carbon composite with Cobalt (AC-Co (0, 10, & 20)%) by stirring-assisted impregnation method as an easy and environmentally friendly procedure. The effectiveness of the material as a catalyst is observed from its surface condition as an active site, and we also consider the electrical and magnetic properties as aspects of the role in photodegradation capability. It was found that AC-Co (10) showed a methylene blue and pesticide degradation capability of >90 % for an adsorbent mass of 1.5 g within 5 days treated without artificial irradiation and stirring to imitate the environmental conditions. The microwave absorption capability by the composite shows a maximum absorption of −19.1 dB at 10.12 GHz for AC-Co (0), while the presence of Co manages to provide a higher working frequency shift but reduced absorption performance. These reported performances are supported by the appropriate distribution of Co particles scattered on the AC surface, larger μ'', and higher consistency of Δ(LO−TO) positions.

Influence of Fiber Type on Electrical, Thermal and Mechanical Properties of Glass Fiber Reinforced Polymer Composites for Insulation Panel Applications

Influence of Fiber Type on Electrical, Thermal and Mechanical Properties of Glass Fiber Reinforced Polymer Composites for Insulation Panel Applications

Polar Metallicity Controlled by Epitaxial Strain Engineering.

The discovery of polar metal opens the door to incorporating electric polarization into electronics with the potential to invigorate next-generation multifunctional electronic devices. Especially, electric polarization can be induced by geometric design in non-polar perovskite oxides. Here, the epitaxial strain exerted on the deposited single-crystalline NdNiO3 thin films is systematically varied in both sign and amplitude by choosing substrates with different lattice mismatch. The pseudocubic NdNiO3(111) film, which is non-polar in its bulk state, is induced to be polar under both compressive and tensile strain. The fine-tuning of epitaxial strain is realized by continuously varying the film thickness using the "thickness-wedge" growth technique, and from the elucidated thickness dependence, the electric polarization and metallicity can be further optimized. Moreover, transitioning from isotropic to anisotropic epitaxial strain gives rise to an ideal polar metal state in the pseudocubic NdNiO3(102) film on an orthorhombic substrate, achieving a remarkably low resistivity of 173 µΩcm at room temperature. The metal-insulator transition in NdNiO3 is completely suppressed and the polar metal state becomes the ground state at all temperatures. These results demonstrate alluring possibilities of induction and manipulation of both electric polarization and electric transport properties in functional perovskite oxides by epitaxial strain engineering.

Corrosion-Resistant Ultrathin Cu Film Deposited on N-Doped Amorphous Carbon Film Substrate and Its Use for Crumpleable Circuit Board.

Copper (Cu) is widely used as an industrial electrode due to its high electrical conductivity, mechanical properties, and cost-effectiveness. However, Cu is susceptible to corrosion, which degrades device performance over time. Although various methods (alloying, physical passivation, surface treatment, etc.) are introduced to address the corrosion issue, they can cause decreased conductivity or vertical insulation. Here, using the nitrogen-doped amorphous carbon (a-C:N) thin film is proposed as a substrate on which Cu is directly deposited. This simple method significantly inhibits corrosion of ultrathin Cu (<20nm) films in humid conditions, enabling the fabrication of ultrathin electronic circuit boards without corrosion under ambient conditions. This study investigates the origin of corrosion resistance through comprehensive microscopic/spectroscopic characterizations and density-functional theory (DFT) calculations: i) diffusion of Cu atoms into the a-C:N driven by stable C-Cu-N bond formation, ii) diffusion of N atoms from the a-C:N to the Cu layer heading the top surface, which is the thermodynamically preferred location for N, and iii) the doped N atoms in Cu layer suppress the inclusion of O into the Cu lattice. By leveraging the ultrathinness and deformability of the circuit board, a transparent electrode and a crumpleable LED lighting device are demonstrated.

The Influence of Annealing Temperature on the Microstructure and Electrical Properties of Sputtered ZnO Thin Films

The Influence of Annealing Temperature on the Microstructure and Electrical Properties of Sputtered ZnO Thin Films

A comparative study on the electrical properties of Ba0.6Sr0.4TiO3 film capacitors with different top electrodes

Au/Ba0.6Sr0.4TiO3 (BST)/La0.5Sr0.5CoO3 (LSCO) and Pt/BST/LSCO ferroelectric capacitors were successfully constructed on (001) LaAlO3 substrates via off-axis magnetron sputtering. X-ray diffraction (XRD) and Phi scan patterns confirmed that the BST film was epitaxial with an out-of-plane tetragonal phase. The ferroelectric and dielectric measurements reveal that, compared with the Pt/BST/LSCO capacitor, the Au/BST/LSCO capacitor exhibits a larger coercive field (∼139.7 kV/cm), smaller permanent polarization (∼2.94 μC/cm2), and lower tunability (∼65.22 %), which may be attributed to the higher difference in work function and weaker depolarization field screen effect of the top electrode, as well as smaller interfacial capacitance of the Au/BST interface than those of the Pt/BST interface. Therefore, based on series capacitor model and leakage behavior analysis, the thickness and dielectric constant of interfacial layer are quantitatively determined to be 3.52 nm and 12.13 for Pt/BST, and 4.42 nm and 5.82 for Au/BST, respectively. Our results pave a way for improving the dielectric performance in electrically tunable microwave devices.

Investigation of thermal, optical properties, AC conductivity and broadband dielectric spectroscopy of poly(ethyl methacrylate)/poly(vinyl chloride) polymer blend

This work reports the structural, thermal, optical and electrical properties of PEMA, PVC and their polyblends. These properties are investigated by FTIR, TGA, UV/Vis and broadband dielectric spectroscopy. FTIR spectra showed that the characteristic bands of PEMA and PVC are affected by blending and displayed red and blue shifts confirming that an intermolecular interaction between PEMA and PVC is occurred. Thermal degradation kinetics of PEMA, PVC and its polyblend samples is investigated in details and the thermal properties of each decomposition stage are estimated. UV measurements analysis revealed that Urbach energy (EU) is increased while optical bandgap decreased upon increasing the PVC content. The indirect and direct band gap (Eig/Edg) values are decreased from (3.95/4.21) to (3.10/3.92) eV. Also, upon increasing the content of PVC, the lattice dielectric constant (εL) is increased from 2.71 to 7.83. Wemple-DiDomenico model is applied for investigating the refractive index dispersion and to calculate the oscillator and dispersion energies. It is observed that the linear/nonlinear parameters are increased nonlinearly with increasing the PVC content. χ(1), χ(3) and n2 values are found to increase from 0.104, 0.213 × 10−13 and 4.01 × 10−12 to 0.363, 31.26 × 10−13 and 5.33 × 10−12. These results make PEMA/PVC polyblend strong candidates for use in the development and design of advanced optoelectronic devices. AC conductivity (σac) and dielectric measurements are carried out at various temperatures in wide frequency range. Jonscher power law is applied and showed that the predominant conduction mechanism in our samples is overlapping large-polaron tunneling (OLPT). The dielectric constant and electrical impedance are found to be frequency and temperature dependent. The investigation of the electric modulus (M*) revealed that M′ is increased non-linearly with increasing the frequency, while M″ spectra displayed two different modes of relaxation. The interfacial polarization (IP) is observed in low frequency region, while, dipolar relaxation is detected in high frequency region.

Nanocrystallization tuning of structural, thermoelectric and electrical properties of SrTiO3-doped vanadate glasses

Nanocrystallization tuning of structural, thermoelectric and electrical properties of SrTiO3-doped vanadate glasses

Intraoperative Cavity Local Delivery System with NETs-Specific Drug Release for Post-Breast Cancer Surgery Recurrence Correction.

Postoperative breast cancer recurrence is tricky due to the limited therapeutic options. Transforming growth factors-β (TGF-β) is vital in promoting postoperative tumor recurrence. However, conventional blocking strategies fail to satisfy both bio-safety and sufficient relapse correction. Neutrophil extracellular traps (NETs) are essential for the spatiotemporal dynamics of TGF-β at tumor-resection sites, whose unique mechanism for local TGF-β amplification could remarkably increase the risk of relapse after surgery. Herein, the principle of NETs formation is ingeniously utilized to construct a surgical residual cavity hydrogel that mimics NETs formation. The hydrogel is prepared based on the electrostatic interaction between histidine (His) and sodium alginate (Alg). Then, arginine deiminase 4 (PAD4) protein is released during NETs formation. Simultaneously, the electrical property of His in hydrogel changes automatically, which further lead to promising localized release of anti-TGF-β. The hydrogel system can realize specific and selective drug release at targeted NETs site over a prolonged period while exhibiting excellent biocompatibility. Superior breast cancer recurrence inhibition is achieved by suppressing TGF-β and related indicators, impeding epithelial-mesenchymal transition (EMT) progression, and rectifying the locally exacerbated immunosuppressive environment within NETs. The novel NETs local microenvironment drug release functional hydrogel will provide inspiration for postoperative recurrence correction strategies.

Structural Analysis and Electrical Property of Acid‐Treated MWCNT

Structural Analysis and Electrical Property of Acid‐Treated MWCNT

Impact of hydrogen plasma treatment on ITO substrate for enhanced performance of CdS/CdTe solar cells

The indium tin oxide (ITO) film was treated with 100 W-power hydrogen plasma for 5 min before being used as a substrate to fabricate thermally evaporated CdS thin films. The structural, optical, and electrical properties of ITO and grown CdS films affected by pre-deposition plasma treatment were studied. SEM images show that the surface of ITO film becomes smoother after treatment. AFM analysis determines a decrease and increase in the surface roughness of ITO and CdS thin films after treating the ITO substrate. The XRD patterns show an improvement in the crystallinity of the fabricated thin films. Increasing the optical energy bandgap up to 3.699 eV and.2.481 eV for ITO and deposited CdS films respectively. So, design simple CdS/CdTe solar cells at a device temperature of 300 K. Enhancing the photovoltaic parameters and an increment of about 20 % in solar cell performance.

Advancing DBD Plasma Chemistry: Insights into Reactive Nitrogen Species such as NO2, N2O5, and N2O Optimization and Species Reactivity through Experiments and MD Simulations.

This study aims to fine-tune the plasma composition with a particular emphasis on reactive nitrogen species (RNS) including nitrogen dioxide (NO2), dinitrogen pentoxide (N2O5), and nitrous oxide (N2O), produced by a self-constructed cylindrical dielectric barrier discharge (CDBD). We demonstrated the effective manipulation of the plasma chemical profile by optimizing electrical properties, including the applied voltage and frequency, and by adjusting the nitrogen and oxygen ratios in the gas mixture. Additionally, quantification of these active species was achieved using Fourier transform infrared spectroscopy. The study further extends to exploring the aerosol polymerization of acrylamide (AM) into polyacrylamide (PAM), serving as a model reaction to evaluate the reactivity of different plasma-generated species, highlighting the significant role of NO2 in achieving high polymerization yields. Complementing our experimental data, molecular dynamics (MD) simulations, based on the ReaxFF reactive force field potential, explored the interactions between reactive oxygen species, specifically hydroxyl radicals (OH) and hydrogen peroxide (H2O2), with water molecules. Understanding these interactions, combined with the optimization of plasma chemistry, is crucial for enhancing the effectiveness of DBD plasma in environmental applications like air purification and water treatment.