Elastin-like Polypeptides Sequence Research Articles

Surface and adsorption characteristics of three elastin-like polypeptide coatings with varying sequence lengths

The surface properties of a family of elastin-like polypeptides (ELPs), differing in molecular weight and sequence length, were investigated to understand how the nature of the polypeptide film might contribute to their thrombogenic profile. Physical adsorption of the ELPs onto Mylar increased surface wettability as the sequence length decreased while X-ray spectroscopy analysis showed an increasing amide content with sequence length. Chemical force microscopy analysis revealed that the ELP-coated surfaces displayed purely hydrophilic adhesion forces that increased as the ELP sequence length decreased. Adsorption isotherms performed using the quartz crystal microbalance with dissipation, showed that the surface coverage increased with ELP sequence length. The longer polypeptides (ELP2 and ELP4) also displayed higher specific dissipation values indicating that they established films with greater structural flexibility and associated water content than the shorter polypeptide, ELP1. Additionally, the stability of the ELP coating was lower with the shorter polypeptides. This study highlights the different surface properties of the ELP coatings as well as the dynamic nature of the ELP adsorbed layer wherein the conformational state may be an important factor contributing to their blood response.

Platelet Adhesion and Fibrinogen Accretion on a Family of Elastin-Like Polypeptides

Previous work in our laboratory showed the potential of using a human recombinant elastin-like polypeptide (ELP) as a thromboresistant coating. In this work we investigate the use of three particular ELPs (ELP1, ELP2 and ELP4), that differ by molecular weight and number of repeating hydrophobic and cross-linking domains, as coatings to improve blood-contacting properties. All three ELPs were passively adsorbed on Mylar surfaces. Differences in water contact angle and surface concentration were found among the three ELP coatings, with the shortest polypeptide, ELP1, being the most hydrophilic and abundant on the surface (55°, 0.76 μg/cm2), followed by ELP2 (55°, 0.35 μg/cm2) and ELP4, the longest of the three (66°, 0.25 μg/cm2), respectively. The blood interactions of the ELP coatings were investigated by measuring fibrinogen adsorption and platelet adhesion in whole blood under laminar flow in a cone and plate viscometer configuration. In general, platelet adhesion to the ELP-coated surfaces was found to correlate with fibrinogen adsorption. Decreases in fibrinogen accretion and platelet adhesion were observed for ELP-coated compared to uncoated surfaces. The magnitude of the decreases was found to depend on the ELP sequence length, with ELP4 exhibiting the lowest levels of fibrinogen adsorption and platelet adhesion at 43 ± 24 ng/cm2 and 113 ± 77 platelets/mm2, respectively.

Development and characterisation of novel cross-linked bio-elastomeric materials

Recombinantly-engineered elastin-like polypeptides (ELPs) possess many of the favourable attributes of the native elastin protein, making them an attractive option for designing biomaterials for tissue-engineering applications. The focus of this study was to synthesize and characterise the bulk material properties of two ELP sequences, ELP2 and ELP4, cross-linked with lysine diisocyanate (LDI). The two distinct ELPs consist of repeating hydrophobic and hydrophilic cross-linking domains in a block co-polymer structure, however, differ by the number of respective domains. Depending on the conditions sets for the cross-linking reactions, two different ELP-based materials were synthesized: a gel-like relatively non-porous material and a porous foam-like material, from both ELP sequences. The physical material properties were characterised by scanning electron microscopy, compression testing, differential calorimetry analysis and swelling analysis. The bulk material properties were found to vary depending on the ELP sequence investigated. ELP gels were also found to have a more dense solidified morphology, lower compressive moduli, higher melting temperature and greater swelling capacity than the porous ELP foams. These novel cross-linked bio-elastomeric materials show promising properties for soft tissue replacement, particularly in load-bearing applications.

Quantification of the effects of chain length and concentration on the thermal behavior of elastin-like polypeptides.

At a specific temperature, elastin-like polypeptides (ELPs) undergo a sharp solubility transition that can be exploited in a variety of applications in biotechnology and medicine. The temperature of the transition varies with ELP sequence, molecular weight, and concentration. We present a single equation of three parameters that quantitatively predicts the transition temperature as a function of ELP length and concentration for an ELP of a fixed composition. This model should be useful both for the design of new ELP sequences that exhibit a desired transition temperature and for the selection of variables to trigger the phase transition of an ELP for a given application.

Genetically encoded synthesis of protein-based polymers with precisely specified molecular weight and sequence by recursive directional ligation: examples from the elastin-like polypeptide system.

We report a new strategy for the synthesis of genes encoding repetitive, protein-based polymers of specified sequence, chain length, and architecture. In this stepwise approach, which we term "recursive directional ligation" (RDL), short gene segments are seamlessly combined in tandem using recombinant DNA techniques. The resulting larger genes can then be recursively combined until a gene of a desired length is obtained. This approach is modular and can be used to combine genes encoding different polypeptide sequences. We used this method to synthesize three different libraries of elastin-like polypeptides (ELPs); each library encodes a unique ELP sequence with systematically varied molecular weights. We also combined two of these sequences to produce a block copolymer. Because the thermal properties of ELPs depend on their sequence and chain length, the synthesis of these polypeptides provides an example of the importance of precise control over these parameters that is afforded by RDL.