Biomass Conversion Efficiency Research Articles

Biomass source influence on hydrogen production through pyrolysis and in line oxidative steam reforming.

This study evaluates the potential of several biomasses differing in nature and composition for their valorization by pyrolysis and in-line oxidative steam reforming. The first task involved the fast pyrolysis of the biomasses in a conical spouted bed reactor at 500ºC, in which product yields were analyzed in detail. Then, the oxidative steam reforming of pyrolysis volatiles (gases and bio-oil) was approached in a fluidized bed reactor. The reforming experiments were performed at 600 ºC, with an steam/biomass (S/B) ratio of 3 and catalyst (Ni/Al2O3) space times of 7.5 and 20 gcat min gvol-1. Concerning equivalence ratio (ER), a value of 0.12 was selected to ensure autothermal operation. Remarkable differences were observed in H2 production depending on the type of biomass. Thus, pine wood led to a H2 production of 9.3 wt%. The lower productions obtained with rice husk (7.7 wt%) and orange peel (5.5 wt%) are associated with their higher ash and fixed carbon content, respectively, which limit the efficiency of biomass conversion to bio-oil. However, in the case of the microalga, the poor performance observed is due to the lower conversion in the reforming step toward gases due to the composition of its pyrolysis volatile stream.

Developing a new ethylene glycol/H2O pretreatment system to achieve efficient enzymatic hydrolysis of sugarcane bagasse cellulose and recover highly active lignin: Countercurrent extraction

Improving pretreatment efficiency is a critical premise in achieving efficient biomass conversion, and obtaining high-performance natural polymers is the guarantee of high-value conversion of biomass. In this study, a new pilot-scale continuous countercurrent pretreatment reaction unit about ethylene glycol-alkali solution was designed for pretreating sugarcane bagasse in order to achieve efficient separation of the three major components of lignocellulose when expanding the scale of pretreatment, reduce lignin deposition on the fiber surface, and obtain highly active lignin and excellent enzymatic hydrolysis efficiency of cellulose. X-ray diffractometer (XRD), X-ray photoelectron spectrometer (XPS), brunauer-emmett-teller (BET) and scanning electron microscope (SEM) methods are used to analyze the structural properties of sugarcane bagasse before and after pretreatment, and high-performance liquid chromatography (HPLC) is used to analyze the monosaccharide components in the enzymatic solution. In addition, the structural properties of the recovered lignin are analyzed by gel permeation chromatography (GPC), 31P NMR and 2D-HSQC-NMR methods. The results indicate that the system can gain a high cellulose recovery of 92.99 % along with a lignin removal of 95.33 %, and recovered lignin has low lignin carbohydrate complexes, low condensation, and rich in phenolic hydroxyl groups for 1.95 mmol/g. Meanwhile, the countercurrent pretreatment system can effectively reduce the deposition of lignin on the cellulose surface, which is evidently superior to the non-countercurrent pretreatment and facilitates the efficiency of enzymatic saccharification of substrate, achieving a high glucose yield of 99% as well as a total sugar yield of 91.11 %. The method efficiently separates biomass in a green manner, and solid residues are easily hydrolyzed, showing potential for industrial-scale production.

Insights into heavy components evolution in the condensed volatiles from amino acids pyrolysis

Heavy components, comprised of molecules with a substantial molecular mass, are essential constituents within volatiles. Within these molecules, nitrogen-containing compounds have a tendency to undergo transformation into coke during thermal treatment, exerting a substantial impact on the efficient and secure utilization of biomass. Three amino acids- alanine with an aliphatic structure, phenylalanine with additional aromatic features, and tryptophan with an extra heterocyclic ring were selected as model compounds, individually subjected to pyrolysis within the temperature range of 450 to 650 °C. The evolution of heavy components and the associated reaction mechanisms were comprehensively explored through extensive characterization and network analysis. The results showed that alanine transformed into heavy components mainly through dehydration followed by dissociation of CH2 and CH. In contrast, phenylalanine and tryptophan tended to undergo fragmentation into C8H7N· and C12H10N2· derivatives, subsequently recombining to form heavy molecules. As the temperature increased, heavy components in alanine-derived volatiles monotonously decreased due to elimination reactions and the breaking of C–C bonds. Conversely, heavy components in phenylalanine and tryptophan initially increased and then decreased due to the enhanced cracked fragments, along with the competitive relationship between aromatization and polymerization reactions. For all three amino acids, there is a positive correlation among the average mass of heavy components, tar yield, and the intensity of permanent free radicals in the char. This implies that we may rapidly predict the evolutionary patterns of heavy components and tar through free radical detection. HCN dissociation is mathematically identified as a pivotal reaction in heavy component evolution, irrespective of amino acid type, possibly unveiling an important pathway for NOx formation. This study shows substantial theoretical significance for the eco-friendly and efficient conversion of nitrogen-rich biomass.

GhMYB52 Like: A Key Factor That Enhances Lint Yield by Negatively Regulating the Lignin Biosynthesis Pathway in Fibers of Upland Cotton (Gossypium hirsutum L.).

In the context of sustainable agriculture and biomaterial development, understanding and enhancing plant secondary cell wall formation are crucial for improving crop fiber quality and biomass conversion efficiency. This is especially critical for economically important crops like upland cotton (Gossypium hirsutum L.), for which fiber quality and its processing properties are essential. Through comprehensive genome-wide screening and analysis of expression patterns, we identified a particularly high expression of an R2R3 MYB transcription factor, GhMYB52 Like, in the development of the secondary cell wall in cotton fiber cells. Utilizing gene-editing technology to generate a loss-of-function mutant to clarify the role of GhMYB52 Like, we revealed that GhMYB52 Like does not directly contribute to cellulose synthesis in cotton fibers but instead represses a subset of lignin biosynthesis genes, establishing it as a lignin biosynthesis inhibitor. Concurrently, a substantial decrease in the lint index, a critical measure of cotton yield, was noted in parallel with an elevation in lignin levels. This study not only deepens our understanding of the molecular mechanisms underlying cotton fiber development but also offers new perspectives for the molecular improvement of other economically important crops and the enhancement of biomass energy utilization.

Direct Degradation of Fresh and Dried Macroalgae by Agarivorans albus B2Z047.

Marine macroalgae are increasingly recognized for their significant biological and economic potential. The key to unlocking this potential lies in the efficient degradation of all carbohydrates from the macroalgae biomass. However, a variety of polysaccharides (alginate, cellulose, fucoidan, and laminarin), are difficult to degrade simultaneously in a short time. In this study, the brown alga Saccharina japonica was found to be rapidly and thoroughly degraded by the marine bacterium Agarivorans albus B2Z047. This strain harbors a broad spectrum of carbohydrate-active enzymes capable of degrading various polysaccharides, making it uniquely equipped to efficiently break down both fresh and dried kelp, achieving a hydrolysis rate of up to 52%. A transcriptomic analysis elucidated the presence of pivotal enzyme genes implicated in the degradation pathways of alginate, cellulose, fucoidan, and laminarin. This discovery highlights the bacterium's capability for the efficient and comprehensive conversion of kelp biomass, indicating its significant potential in biotechnological applications for macroalgae resource utilization.

Mild γ-Butyrolactone/Water Pretreatment for Highly Efficient Sugar Production from Corn Stover.

In this study, γ-butyrolactone/water (GBL/H2O) was explored as a mild, efficient, and cost-effective binary solvent pretreatment to enhance hydrolyzability of corn stover (CS). Key pretreatment parameters-reaction time, temperature, and H2SO4 concentration-were systematically investigated for their effects on the physicochemical properties of CS. Specifically, increased temperature and acid concentration significantly decreased cellulose crystallinity (from 1.39 for untreated CS to 1.04 for CS pretreated by GBL/H2O with 100 mM H2SO4 at 120°C for 1h) and promoted lignin removal (47.3% for CS pretreated by GBL/H2O with 150 mM H2SO4 at 120°C for 1h). Acknowledging the cellulase's limited hydrolysis efficiency, a dual-enzyme scheme using a low cellulase dosage (10 FPU/g) supplemented with β-glucosidase or xylanase was tested, enhancing hydrolysis of CS pretreated under low temperature-long duration and high temperature-short duration conditions, respectively. Optimum sugar release was obtained from CS pretreated with GBL/H2O and 150 mM H2SO4 at 120°C for 1h, achieving 98% glucan and 82.3% xylan conversion, compared with 53.9% and 17% of glucan and xylan conversion from untreated CS. GBL/H2O pretreatment outperformed other binary systems in literature, achieving the highest sugar conversions with lower enzyme loading. These results highlight the potential of GBL/H2O pretreatment for efficient biomass conversion, contributing to the goals of the green economy.

Performance evaluation of carbon-negative syngas production via chemical looping reforming of methane from biomass pyrolysis volatiles

To realize the clean and efficient directional conversion of biomass, chemical looping reforming of biomass volatile CH4 based on a decoupling strategy is expected to carry out carbon-negative production of hydrogen-rich syngas. In this paper, a multi-functional oxygen carrier (NiFe2O4@SBA-16) for encapsulating the active metal oxide component NiFe2O4 with a three-dimensional interconnecting pore molecular sieve SBA-16 was designed. The experimental results showed that the modification strategy of composite metal oxide encapsulation improved syngas selectivity and CH4 conversion based on the fixed-bed reactor. 20 %NiFe2O4@SBA-16 showed 22.1 % CH4 conversion and 92.6 % CO selectivity under 750 °C, and it maintained good cycle stability after 15 cycles. The H2/CO ratio was effectively improved by adding part of CO2 into the feed gas, and the CH4 conversion reached over 35 %. This study provides essential data for the clean preparation of hydrogen-rich syngas from biomass and the development and design of multifunctional oxygen carriers.

Expression of cellobiose dehydrogenase gene in Aspergillus niger C112 and its effect on lignocellulose degrading enzymes.

Cellobiose dehydrogenase (CDH) is one of the cellulase auxiliary proteins, which is widely used in the field of biomass degradation. However, how to efficiently and cheaply apply it in industrial production still needs further research. Aspergillus niger C112 is a significant producer of cellulase and has a relatively complete lignocellulose degradation system, but its CDH activity was only 3.92 U. To obtain a recombinant strain of A. niger C112 with high cellulases activity, the CDH from the readily available white-rot fungus Grifola frondose had been heterologously expressed in A. niger C112, under the control of the gpdA promoter. After cultivation in the medium with alkali-pretreated poplar fiber as substrate, the enzyme activity of recombinant CDH reached 36.63 U/L. Compared with the original A. niger C112, the recombinant A. niger transformed with Grifola frondosa CDH showed stronger lignocellulase activity, the activities of cellulases, β-1, 4-glucosidase and manganese peroxidase increased by 28.57, 35.07 and 121.69%, respectively. The result showed that the expression of the gcdh gene in A. niger C112 could improve the activity of some lignocellulose degrading enzymes. This work provides a theoretical basis for the further application of gcdh gene in improving biomass conversion efficiency.

Artificial intelligence methods for modeling gasification of waste biomass: a review.

Gasification is a highly promising thermochemical process that shows considerable potential for the efficient conversion of waste biomass into syngas. The assessment of the feasibility and comparative advantages of different biomass and waste gasification schemes is contingent upon a multifaceted combination of interrelated criteria. Conventional analytical approaches employed to facilitate decision-making rely on a multitude of inadequately defined parameters. Consequently, substantial efforts have been directed toward enhancing the efficiency and productivity of thermochemical conversion processes. In recent times, artificial intelligence (AI)-based models and algorithms have gained prominence, serving as indispensable tools for expediting these processes and formulating strategies to address the growing demand for energy. Notably, machine learning (ML) and deep learning (DL) have emerged as cutting-edge AI models, demonstrating exceptional effectiveness and profound relevance in the realm of thermochemical conversion systems. This study provides an overview of the machine learning (ML) and deep learning (DL) approaches utilized during gasification and evaluates their benefits and drawbacks. Many industries and applications related to energy conversion systems use AI algorithms. Predicting the output of conversion systems and subjects linked to optimization are two of this science's critical applications. This review sheds light on the burgeoning utility of AI, particularly ML and DL, which have garnered significant attention due to their applications in productivity prediction, process optimization, real-time process monitoring, and control. Furthermore, the integration of hybrid models has become commonplace, primarily owing to their demonstrated success in modeling and optimization tasks. Importantly, the adoption of these algorithms significantly enhances the model's capability to tackle intricate challenges, as DL methodologies have evolved to offer heightened accuracy and reduced susceptibility to errors. Within the scope of this study, an exhaustive exploration of ML and DL techniques and their applications has been conducted, uncovering existing research knowledge gaps. Based on a comprehensive critical analysis, this review offers recommendations for future research directions, accentuating the pivotal findings and conclusions derived from the study.

Influence of Impurities in the Chemical Processing Chain of Biomass on the Catalytic Valorisation of Cellulose towards γ-Valerolactone

The conversion of lignocellulosic biomass to valuable chemicals such as levulinic acid and γ-valerolactone is a promising approach for achieving a sustainable circular economy. However, the presence of impurities during the stepwise chemical processing chain of the biomass feedstock can significantly impact both the hydrolysis and hydrogenation steps implemented to convert the cellulosic feedstock to levulinic acid and further to γ-valerolactone, respectively. This review article explores the effects of those impurities by classifying them into two groups, namely endogenous and exogenous types, based on whether they originate directly from the raw lignocellulosic biomass or arise during its multi-step chemical processing. Endogenous impurities include heavy metals, alkali metals, alkaline earth metals, proteins, and side products from the downstream treatment of cellulose, while exogenous impurities are introduced during physical pre-treatments such as ball milling or during the hydrolysis step, or they might originate from the reactor setup. The specific catalyst deactivation by carbonaceous species such as humins and coke is considered. The mechanisms of impurity-induced catalyst deactivation and by-product formation are thoroughly discussed. Additionally, strategies for minimizing the detrimental effects of impurities on biomass conversion and enhancing catalytic efficiency and stability are also proposed.

Biomass conversion and radiocaesium (Rad-Cs) leaching behaviors of radioactive grass in anaerobic wet fermentation systems: Effects of pre-treatments

Persistent concerns regarding environmental hazards arise from the difficulty in disposing of radioactive plant-based wastes originating from the nuclear accident at the Fukushima Daiichi Nuclear Power Plant (FNPP) in Japan in 2011. In this study, three anaerobic digestion (AD) strategies were proposed: Sole anaerobic wet fermentation, and wet fermentations with either alkaline-heat or ultrasonic pre-treatment, which were employed for long-term anaerobic treatment of a genuine radioactive grass stemming from the FNPP accident. The objectives of this work are to investigate the effects of pre-treatments on biomass conversion efficiency and to gain insight into the leaching behavior of radiocaesium (Rad-Cs) within AD processes. Experimental results indicate that by introducing alkaline-heat and ultrasonic pre-treatments to AD systems, the removal efficiencies of total solids (TS) from the raw grass increased by 60.8 % and 42.5 %, respectively, compared to sole wet fermentation. Pre-treatments have been shown to enhance the stability of AD systems, both in terms of enhancing methane production and mitigating pH fluctuations triggered by the accumulation of organic acids. Remarkably, even though the Rad-Cs leaching rate was highest when the AD system was fed with the alkaline-heat pre-treated grass, it remained unsatisfactory at only 5.77 %. We inadvertently isolated a soil-like component from the raw grass, and analyzed both its proportion in the raw grass and the radioactivity intensity. The results indicate that although the soil constituted only 9.51 % TS of the raw grass, it accounted for a significant 81.35 % of the total radioactivity. The soil, which has a pronounced affinity for ionic Cs, being mixed into the raw grass, was identified as the primary factor limiting the leaching efficiency of Rad-Cs throughout both the pre-treatment and wet fermentation phases.

Dual assistance of surfactants in glycerol organosolv pretreatment and enzymatic hydrolysis of lignocellulosic biomass for bioethanol production

This study investigated an innovative strategy of incorporating surfactants into alkaline-catalyzed glycerol pretreatment and enzymatic hydrolysis to improve lignocellulosic biomass (LCB) conversion efficiency. Results revealed that adding 40 mg/g PEG 4000 to the pretreatment at 195 °C obtained the highest glucose yield (84.6%). This yield was comparable to that achieved without surfactants at a higher temperature (240 °C), indicating a reduction of 18.8% in the required heat input. Subsequently, Triton X-100 addition during enzymatic hydrolysis of PEG 4000-assisted pretreated substrate increased glucose yields to 92.1% at 6 FPU/g enzyme loading. High-solid fed-batch semi-simultaneous saccharification and co-fermentation using this dual surfactant strategy gave 56.4 g/L ethanol and a positive net energy gain of 1.4 MJ/kg. Significantly, dual assistance with surfactants rendered 56.3% enzyme cost savings compared to controls without surfactants. Therefore, the proposed surfactant dual-assisted promising approach opens the gateway to economically viable enzyme-mediated LCB biorefinery.

Energy Recovery Efficiency of Integrating Anaerobic Co-Digestion of Pig Slurry and Feedlot Cattle Manure and Hydrothermal Carbonization of Anaerobic Sludge Cake

Hydrothermal carbonization (HTC) is a technology designed to improve the efficiency of bioenergy recovery by subjecting biomass to high-temperature and high-pressure conditions. By integrating this technical feature with anaerobic digestion (AD), enhanced energy recovery efficiency is achieved in treating anaerobic digestate (AD-T). The study investigates enhancing bioenergy recovery efficiency through an integrated process, combining AD of livestock manure and HTC. The primary objective is to improve the energy conversion efficiency of biomass characterized by varying solid contents and chemical compositions. Shortening the hydraulic retention time (HRT) in AD of livestock manure resulted in decreased degradation rate efficiency within the AD-T. This led to increased solid material accumulation, which was crucial for the subsequent HTC reaction. The HTC reaction exhibited its maximum bioenergy recovery at 160 °C. The input energy of the livestock manure, obtained by mixing pig slurry and feedlot cattle manure in a 1:1 (w/w) ratio, was 171,167 MJ/day. Under different HRT conditions (40, 30, and 20 days), recoverable energy from AD of livestock manure ranged from 60,336 to 68,517 MJ/ton. Integration of HTC increased net bioenergy recovery to 106,493 to 130,491 MJ/day under corresponding HRT conditions, highlighting the potential of integrating HTC with AD from livestock manure for enhanced bioenergy recovery efficiency.

Lignocellulolytic Potential of Microbial Consortia Isolated from a Local Biogas Plant: The Case of Thermostable Xylanases Secreted by Mesophilic Bacteria.

Lignocellulose biomasses (LCB), including spent mushroom substrate (SMS), pose environmental challenges if not properly managed. At the same time, these renewable resources hold immense potential for biofuel and chemicals production. With the mushroom market growth expected to amplify SMS quantities, repurposing or disposal strategies are critical. This study explores the use of SMS for cultivating microbial communities to produce carbohydrate-active enzymes (CAZymes). Addressing a research gap in using anaerobic digesters for enriching microbiomes feeding on SMS, this study investigates microbial diversity and secreted CAZymes under varied temperatures (37 °C, 50 °C, and 70 °C) and substrates (SMS as well as pure carboxymethylcellulose, and xylan). Enriched microbiomes demonstrated temperature-dependent preferences for cellulose, hemicellulose, and lignin degradation, supported by thermal and elemental analyses. Enzyme assays confirmed lignocellulolytic enzyme secretion correlating with substrate degradation trends. Notably, thermogravimetric analysis (TGA), coupled with differential scanning calorimetry (TGA-DSC), emerged as a rapid approach for saccharification potential determination of LCB. Microbiomes isolated at mesophilic temperature secreted thermophilic hemicellulases exhibiting robust stability and superior enzymatic activity compared to commercial enzymes, aligning with biorefinery conditions. PCR-DGGE and metagenomic analyses showcased dynamic shifts in microbiome composition and functional potential based on environmental conditions, impacting CAZyme abundance and diversity. The meta-functional analysis emphasised the role of CAZymes in biomass transformation, indicating microbial strategies for lignocellulose degradation. Temperature and substrate specificity influenced the degradative potential, highlighting the complexity of environmental-microbial interactions. This study demonstrates a temperature-driven microbial selection for lignocellulose degradation, unveiling thermophilic xylanases with industrial promise. Insights gained contribute to optimizing enzyme production and formulating efficient biomass conversion strategies. Understanding microbial consortia responses to temperature and substrate variations elucidates bioconversion dynamics, emphasizing tailored strategies for harnessing their biotechnological potential.

Synergistic bioconversion of organic waste by black soldier fly (Hermetia illucens) larvae and thermophilic cellulose-degrading bacteria.

This study examines the optimum conversion of Wuzhishan pig manure by Black Soldier Fly Larvae (BSFL) at various phases of development, as well as the impact of gut microbiota on conversion efficiency. In terms of conversion efficiency, BSFL outperformed the growing pig stage (GP) group, with significantly higher survival rates (96.75%), fresh weight (0.23 g), and larval conversion rate (19.96%) compared to the other groups. Notably, the GP group showed significant dry matter reductions (43.27%) and improved feed conversion rates (2.17). Nutritional composition varied, with the GP group having a lower organic carbon content. High throughput 16S rRNA sequencing revealed unique profiles, with the GP group exhibiting an excess of Lactobacillus and Clostridium. Promising cellulose-degrading bacteria in pig manure and BSFL intestines, including Bacillus cereus and Bacillus subtilis, showed superior cellulose degradation capabilities. The synergy of these thermophilic bacteria with BSFL greatly increased conversion efficiency. The BSFL1-10 group demonstrated high growth and conversion efficiency under specific conditions, with remarkable larval moisture content (71.11%), residual moisture content (63.20%), and waste reduction rate (42.28%). This study sheds light on the optimal stages for BSFL conversion of pig manure, gut microbiota dynamics, promising thermophilic cellulose-degrading bacteria, and the significant enhancement of efficiency through synergistic interactions. These findings hold great potential for sustainable waste management and efficient biomass conversion, contributing to environmental preservation and resource recovery.

Efficient Conversion of Waste Plant Biomass to Bioethanol fuel as Environmental Recycling Process and Renewable Energy: A useful for Climate Change

Agricultural waste biomass has already been transferred to bioethanol and used as energy related products, although many issues such as efficiency and productivity still exist to be overcome. In this chapter, the protein engineering was applied to generate enzymes with completely reversed coenzyme specificity and developed recombinant yeasts containing those engineered enzymes for construction of an efficient biomass-ethanol conversion system. Recombinant yeasts were constructed with the genes encoding a wild type xylose reductase (XR) and the protein engineered xylitol dehydrogenase (XDH) (with NADP) of Pichia stipitis. These recombinant yeasts were characterized based on the enzyme activity and fermentation ability of xylose to ethanol. The protein engineered enzymes were expressed significantly in Saccharomyces cerevisiae as judged by the enzyme activity in vitro. Ethanol fermentation was measured in batch culture under anaerobic conditions. The significant enhancement was found in Y-ARS strain, in which NADP+-dependent XDH was expressed; 85% decrease of unfavorable xylitol excretion with 26% increased ethanol production, when compared with the reference strain expressing the wild–type XDH.

Selective hydrogenation of furfural to furfuryl alcohol through hydrogenation spillover over amorphized HA zeolite encapsulated platinum clusters

Design of heterogeneous catalyst to achieve efficient conversion of biomass to high added-value chemicals is still very attractive. Herein, taking industrially important selective hydrogenation of furfural to furfuryl alcohol as an example, the designed amorphized HA zeolite encapsulation of platinum clusters (denoted as Pt@HA) exhibited excellent catalytic selectivity at totally conversion of the reactant furfural, along with good reusability and poison resistance ability. The selected amorphized HA zeolite with very small pore size constrained the reactant furfural to be reacted through hydrogen spillover process at zeolite surface, instead of to be adsorbed and activated onto Pt surface. Resulting from the stronger interaction between nucleophilic oxygen atom of aldehyde group and acid site at HA zeolite surface than that of furan ring group, furfural preferred to adsorb onto Pt@HA surface with the end of aldehyde group rather than the end of furan ring group, thus facilitating the spilled H atom to react with aldehyde group to give desired furfuryl alcohol product exclusively.

LIGNOCELLULOSE BIOMASS DELIGNIFICATION USING ACID HYDROTROPE AS GREEN SOLVENT: A MINI-REVIEW

"Efficient and cost-effective conversion of lignocellulosic biomass into usable forms of energy presents unique challenges. Lignocellulosic biomass, comprising cellulose, hemicelluloses, and lignin, necessitates advanced conversion technologies. Common commercial delignification techniques, including kraft pulping, sulfite pulping, acid hydrolysis, and organosolv pulping, often involve harsh conditions leading to structural changes in lignin and environmental impacts. To address these issues, acid hydrotropes have emerged as a promising method for lignin extraction. Acid hydrotropes, represented by p-toluenesulfonic acid (p-TsOH), enable the solubilization of hydrophobic substances like lignin. This mini-review provides an overview of various lignocellulose fractionation techniques and explores the acid hydrotrope approach. The mechanism behind acid hydrotropic fractionation is discussed, and its performance is evaluated. In conclusion, the review emphasizes the pivotal role of the acid hydrotrope approach in advancing lignocellulosic biomass conversion technology, promoting a sustainable and efficient bio-based economy."

Biohydrogen improvement from reactive honeycomb wood based on inert heat recirculating

Hydrogen production from biomass is an efficient and clean utilization way for renewable energy to significantly alleviate the energy crisis. In order to improve the biomass conversion efficiency, a device combining honeycomb structure wood and inert porous pellets was proposed, and the combustion characteristics of honeycomb wood was studied with different biomass species and pore structures. The results indicated that softwood had the higher syngas yield compared with hardwood, and the hydrogen yield was up to 9.0 %. The increasing of inlet air velocity improved combustion temperature, but it was not conducive to syngas production. In addition, circle shape structure showed the stable combustion rate and the high conversion efficiency due to the uniform pore distribution. With the increasing of pore number, outlet temperature and hydrogen production increased first and then decreased. Moreover, syngas yield improved as the pore diameter increased and the maximum hydrogen growth rate reached 256 %. Meanwhile, the co-combustion mechanism of honeycomb wood and inert pellets was revealed, and the efficient realization of heat-hydrogen coproduction had practical guiding significance for optimizing the energy structure.

Characterization of a novel thermostable α-l-arabinofuranosidase for improved synergistic effect with xylanase on lignocellulosic biomass hydrolysis without prior pretreatment

Utilizing thermostable enzymes in biomass conversion processes presents a promising approach to bypass pretreatment, garnering significant attention from the biorefinery industry. A novel discovered α-l-arabinofuranosidase, Abf4980, exhibits exceptional thermostability by maintaining full activity after 24 h of incubation at 70 °C. It effectively acts on polyarabinosides, cleaving α-1,2- and α-1,3-linked arabinofuranose side chains from water-soluble wheat arabinoxylan while releasing xylose. When synergistically combined with the thermostable bifunctional xylanase/β-glucanase CbXyn10C from Caldicellulosiruptor bescii at an enzyme-activity ratio of 6:1, Abf4980 achieves the highest degradation efficiency for wheat arabinoxylan. Furthermore, Abf4980 and CbXyn10C demonstrated remarkable efficacy in hydrolyzing unmodified wheat bran and corn cob to generate arabinose and xylooligosaccharides. This discovery holds promising opportunities for improving the efficiency of lignocellulosic biomass conversion into fermentable sugars.