Adsorption Efficiency Research Articles

Carbon-doped CuO nanoparticle-constructed single tube adsorbent for high efficient adsorption of Pb2+ at near room temperature

How to prepare adsorbents using economical, environmentally friendly and simple methods has become the focus of research. In this paper, silk cotton (SC) was used as a biomass template impregnated with copper nitrate solution and then calcined to prepare CuO-based adsorbent. Carbon-doped CuO (C/CuO-400) adsorbent was obtained under 400 °C air calcination calcination. It completely replicates the morphology of kapok and consists of uniformly smaller nanoparticles. The effects of different calcination temperatures, adsorption temperatures, adsorption times, adsorbent dosages and different concentrations on the adsorption of lead ions were investigated. The results showed that C/CuO-400 had a good adsorption effect on Pb2+, which was suitable for Pseudo second-order and Langmuir, and the maximum adsorption amount of Pb2+ was 588.24 mg/g with good Reusability. This environmentally friendly, economical and simple to operate biomass template prepared adsorbent of single tube C/CuO has good adsorption effect on lead ions, which is very meaningful and easy to promote the preparation of adsorbent.

BioMOF@PAN Mixed Matrix Membranes as Fast and Efficient Adsorbing Materials for Multiple Heavy Metals' Removal.

Heavy metal ions are a common source of water pollution. In this study, two novel membranes with biobased metal-organic frameworks (BioMOFs) embedded in a polyacrylonitrile matrix with tailored porosity were prepared via nonsolvent induced phase separation methods and designed to efficiently adsorb heavy metal ions from oligomineral water. Under optimized preparation conditions, stable membranes with high MOF loading up to 50 wt % and a cocontinuous sponge-like morphology and a high water permeability of 50-60 L m-2 h-1 bar-1 were obtained. The tortuous flow path in combination with a low water flow rate guarantees maximum contact time between the fluid and the MOFs, and thus a high heavy metal capture efficiency in a single pass. The performances of these BioMOF@PAN membranes were investigated in the dynamic regime for the simultaneous removal of Pb2+, Cd2+, and Hg2+ heavy metals from aqueous environments in the presence of common interfering ions. The new composite adsorbing membranes are capable of reducing the concentration of heavy metal pollutants in a single pass and at much higher efficiency than previously reported membranes. The enhanced performance of the mixed matrix membranes is attributed to the presence of multiple recognition sites which densely decorate the BioMOF channels: (i) the thioether groups, deriving from the S-methyl-l-cysteine and (S)-methionine amino acid residues, able to recognize and capture Pb2+ and Hg2+ ions and (ii) the oxygen atoms of the oxamate moieties, which preferentially interact with Cd2+ ions, as revealed by single crystal X-ray diffraction. The flexibility of the pore environments allows these sites to work synergically for the simultaneous capture of different metal ions. The stability of the membranes for a potential regeneration process, a key-factor for the effective feasibility of the process in real life applications, was also evaluated and confirmed less than 1% capacity loss in each cycle.

Fabrication of a cost-effective metal oxide-based adsorbent from industrial waste slag for efficient CO2 separation under flue gas conditions

Efficient and affordable adsorbents for CO2 capture are essential in implementing carbon capture technology to mitigate the negative impact of greenhouse gas emissions. This study focuses on synthesizing new nanoporous adsorbents from industrial waste slag using a simple and cost-effective coprecipitation method. In this method, raw slag was milled for 48 h and used as a benchmark for comparing two newly synthesized adsorbents. Selectivity and pure gas isotherm experiments were conducted for all adsorbents in the 25–65°C temperature range and under harsh industrial conditions of 65°C and 15 % CO2. This study utilized the response surface methodology (RSM) to optimize the CO2 adsorption parameters. Specifically, the optimized adsorption conditions were determined for the 15/85 % CO2/N2 condition, and the optimal values for pressure and temperature were found to be 5 bar and 45°C, resulting in CO2/N2 selectivity of 5.65. The NH3-slag adsorbent was identified as the superior choice based on its selectivity and maximum adsorption capacity. The maximum adsorption capacity and cyclic efficiency were determined to be 4.15 mmol/g and 98.1 %, respectively, at a temperature, pressure, and composition of 45°C, 5 bar, and 15 % CO2. Isotherm and thermodynamic models were employed to further investigate the adsorption process. The isotherm results indicated that the adsorption of CO2 by adsorbents occurred heterogeneously in patch-wise sites. Meanwhile, the thermodynamic parameters showed that the process was exothermic and spontaneous, with ΔH° falling below 20 (kJ/mol), showing physisorption phenomena.

Flotation separation of maghara coal in Egypt for the removal of hazardous Cr(VI) from industrial wastewater

ABSTRACT Due to its serious toxicity, wastewater contaminated with hexavalent chromium (Cr(VI)) has become an increasing environmental concern. Herein, a novel flotation separation of maghara coal in Egypt for Cr(VI) removal was proposed to separate coal to three types of maceral group fractions including liptinite, vitrinite, and inertinite via controlling in density as a function in the degree of coalification. The results implied that the activated inertinite macerals (AIM) have the highest carbon and lowest nitrogen levels among the entire maceral groups. The Langmuir isotherm model exhibited a high adsorption capacity of the AIM sample (1226. 21 mg/g) compared to pre-flotation separation sample (877.55 mg/g). Therefore, the flotation separation of maghara coal played a vital role in the Cr(VI) removal. The residuary concentration of Cr(VI) after adsorption onto AIM was close to 0.037 mg L−1 at pH = 2, which satisfies the industrial wastewater discharge standard. In addition, the removal of Cr(VI) onto AIM surface has been demonstrated to be highly effective via the adsorption and reduction process. The oxygen-containing functional groups could strengthen the interaction between Cr(VI) and AIM surface through the reducing reactions. The accelerating effect of organic acids was investigated for the capture of Cr(VI) and the efficiency in the presence of tartaric acid was improved up to 99.96% within 48 h compared to other organic acids. Therefore, this research provides a sophisticated strategy for separating coal to highly efficient adsorbents for wastewater remediation.

Adsorption, photocatalysis, and sonocatalytic activities of LaFeO3/methylcellulose/multi-walled carbon nanotubes-NiCu2O4/Zn for removal of organic pollutant: preparation, main factor, and mechanism

The primary objective of this study was to create and analyze a new type of LaFeO3/methylcellulose/multi-walled carbon nanotubes-NiCu2O4/Zn nanocomposite, called LFO/MC/MWCNT-NCO/Z, which has multiple functions. Structural investigation using field emission scanning electron microscopy showed that the nanoparticles (40–50 nm) were evenly distributed throughout the nanocomposite, suggesting that they were successfully incorporated without any clumping. FTIR research verified the existence of functional groups that facilitate electrostatic interactions with contaminants, hence strengthening catalytic performance and improving adsorption efficiency. The BET analysis revealed a significantly high specific surface area of 72.61 m2/g, which greatly enhances its ability to adsorb substances. The nanocomposite demonstrated high removal efficiency in adsorption (74.55%), photocatalysis (68.19%), and sonocatalysis (91.22%) procedures, highlighting its potential for effectively removing bisphenol A as organic pollutants. The synthesized LFO/MC/MWCNT-NCO/Z nanocomposite shows great potential in effectively eliminating organic contaminants from water solutions. This offers a sustainable way to address water pollution and protect human health and the environment.

Preparation and characterization of hierarchically porous hybrid gels for efficient dye adsorption.

Water treatment faces significant challenges due to the increasing complexity of pollutants and the need for more efficient, sustainable treatment methods. However, current adsorbent materials often struggle with issues such as low adsorption capacity, slow kinetics, and poor reusability, limiting their practical application. In this study, we developed a novel hierarchical porous hybrid gel (HPHG) for water treatment to address the limitations of conventional adsorbents. The HPHG features a multi-level porous structure (from 48 ± 28 nm to 4385 ± 823 nm) that significantly enhances its porosity and specific surface area. We systematically investigated the relationship between the material's structure and its adsorption performance. Kinetic studies revealed a tendency towards a pseudo-second-order adsorption model, attributed to the material's unique structural features that facilitate rapid mass exchange channels inside HPHG and provide abundant active sites for pollutant adsorption. Reusability tests demonstrated that the material retained 85.4% of its initial adsorption capacity after five adsorption-desorption cycles, highlighting its potential for practical applications. This study provides valuable insights into structure-performance relationships in advanced water treatment materials, offering a promising approach for designing next-generation adsorbents with superior efficiency and sustainability.

High throughput detection of veterinary drug residues in chicken and eggs

Co-extraction of multiple types of target substances is the key to achieve high throughput detection. In this work, PDA@MOF-808/PAN NFsM was prepared by co-modified polyacrylonitrile nanofiber membrane (PAN NFsM) with polydopamine (PDA) and metal-organic framework-808 (MOF-808), and its potential as a solid-phase extraction (SPE) adsorbent was investigated by using the most typical nine veterinary drug residues in eggs and chicken as model target substances. The results show that PDA@MOF-808/PAN NFsM could effectively co-extract all the target substances (adsorption efficiency ranged from 81.46 % to 96.78 %), and had good capability of sample matrix purification (matrix effect was lower than −15.26 %), so a new SPE method has been established. Combined with UPLC-MS/MS, the detection limits were 0.3 to 3.1 μg/kg, the recoveries were between 71.02 % and 106.48 %, and the relative standard deviations were lower than 12.03 %, indicating that the method has considerable good sensitivity, accuracy and precision.

Efficient adsorption of acid orange 7 from wastewater using novel bio-natural granular bentonite-sawdust-corncob (GBSC): Mixture optimization, adsorption kinetic and regeneration

The removal of dyes from industrial wastewater is one of the most environmental challenges that should be addressed through sustainable technologies. In this study, a novel green and cost-effective granular from bentonite and bio-wastes of sawdust and corncob (GBSC) was prepared for sustainable treatment of acid orange 7 (AO7) dye wastewater. The d-optimal mixture method was employed to determine the optimum combination of the GBSC in terms of dye adsorption and structure stability. Characterizations of the GBSC were investigated using SEM, XRD, FTIR and BET analyses and compared with bentonite powder (BP), modified bentonite powder (MBP), and granular modified bentonite (GMB). According to the results, a mixture of bentonite 60 wt%, sawdust 20 wt% and corncob 20 wt% at 550 °C yielded the optimal combination of the GBSC which resulted to the highest adsorption capacity 135.22 mg/g, the lowest mass loss 3.1% and maximum crushing strength 12.275 N. The kinetic and isotherm of the adsorption data were fitted well by the pseudo-second-order model and Langmuir isotherm. Our finding suggested a green circular economy model by utilizing agriculture wastes (sawdust and corncob) to synthesize GBSC for sustainable dye wastewater treatment, which offers a cost-effective adsorbent (0.907 $/g) with high regeneration (4 times reusability with 40.5% removal rate) to keep them in circulation for as long as possible.

Room-temperature synthesis of covalent organic frameworks with dual functional groups for high-performance adsorption of diclofenac sodium from aqueous solution

Diclofenac sodium (DCF) are commonly found in ambient waterways due to its widespread use, and this poses significant risks to both human health and ecosystems. In this study, we have designed and synthesized a series of imine-linked covalent organic frameworks (COFs) with dual functional groups using a triple assembly strategy. Specifically, the platform molecules 2,5-dimethoxyterephthalaldehyde (DMTP), 2,5-dihydroxyterephthalaldehyde (DHTP), and 1,3,5-tris(4-aminophenyl)benzene (TAPB) were employed for the direct fabrication of COFs through Schiff base condensation reactions. As a proof of concept, three room-temperature synthesized COFs (COF TAPB-DMTP-[OH]n, where n represents the molar mass of DHTP, with n values of 0.02, 0.03, and 0.04) were used for DCF adsorption from water. The adsorption isotherms, kinetics, pH effects, ionic strength, co-existing ions, and COF regeneration for DCF were thoroughly investigated. The incorporation of methoxy (-OMe) and hydroxyl (-OH) groups serves as a functional strategy to facilitate hydrogen bonding interactions with DCF molecules. Consequently, the developed COFs, featuring an ultrahigh surface area and mesoporous structure, demonstrated a maximum adsorption capacity of 413.2mg/g and a rate constant k2 of 0.0435g/mg/min, which exceeds the performance of the majority of previously described adsorbents. The adsorption capacity toward DCF remained nearly unchanged after five regeneration cycles of the COF. Furthermore, the self-prepared adsorbent demonstrated efficient adsorption of DCF from real environmental water, indicating its potential for practical DCF removal applications.

Ultrasensitive Assay for the Sports Banned Stimulant Clenbuterol Enabled by Polystyrene-Gold Nanocomposite Platform

An electrochemical biosensor based on a polystyrene-gold nanocomposite was fabricated for the ultrasensitive sensing of clenbuterol. The PS-Au nanocomposite was synthesized by modifying polystyrene with triazine and aminothiazole groups, followed by the in-situ reduction of AuNPs. The PS-Au/SPCE exhibited a linear range (0.01-10μM) with a limit of detection of 3.2nM towards clenbuterol along with high selectivity and good stability. The sensor platform showcased its prowess by accurately quantifying clenbuterol in milk specimens fortified with known analyte concentrations, yielding recovery percentages within the range of 96.5% to 102.8%, accompanied by relative standard deviations below 4.2%. The superior performance of the PS-Au/SPCE is due to the synergistic effect of the high surface area and electrocatalytic activity of the AuNPs, the efficient adsorption of clenbuterol on the functionalized polystyrene matrix, and the enhanced electron transfer kinetics.

Fluorescent cellulose nanofibrils hydrogels for sensitive detection and efficient adsorption of Cu2+ and Cr6+

Increasing chromium and copper pollution poses a significant threat to the global environment and human health. It is crucial to detect and remove Cu (II) and Cr (VI) from water. Cellulose nanofibrils (CNF)-based hydrogels were a natural, abundant, and biocompatible material that has attracted great attention for bio adsorption applications. In this work, a new fluorescent CNF-based hydrogel (PAA-CNF-W) was prepared for the high-efficiency adsorption and sensitive detection of Cu (II) and Cr (VI). CNF was introduced as a natural backbone to construct a three-dimensional porous structure, which increased the specific surface area and provided additional active sites, exhibiting excellent adsorption properties for Cu (II) (159.24 mg/g) and Cr (VI) (173.87 mg/g). Moreover, the synthesized dansyl chloride derivatives with fluorescent properties were introduced to the hydrogel and formed chelates with the metals leading to fluorescence quenching. PAA-CNF-W hydrogels showed high sensitivity to the detection limit (LOD) of Cu (II) (28.70 mg/L) and Cr (VI) (1.45 mg/L). The kinetic study revealed that pseudo-second order kinetics was the best-fitting model. The Langmuir isotherm was the best adjustment model. The study provides a new idea for efficient detection and removal of Cu (II) and Cr (VI) from wastewater by cellulose materials.

Eco-friendly tea waste magnetite nanoparticles for enhanced adsorptive removal of norfloxacin and paroxetine from water

Traces of pharmaceuticals have been detected in water cycle raising concerns regarding the potential risks to human health and aquatic environment. Accordingly, removal of such compounds from water samples is a major concern. Herein, a facile and green NaOH modified tea waste magnetite nanoparticles have been fabricated for the adsorptive removal of a commonly used antibiotic (norfloxacin) and antidepressant (paroxetine) from water samples. The synthesized nanoparticles were characterized using TEM, FT-IR, DLS and VSM. Factors affecting the adsorption efficiency have been investigated with respect to pH (5, 7 and 9), adsorbent amount (0.125, 0.25 and 0.5 g), initial drug concentration (25, 50 and 100 µg/mL) and contact time (0.5, 1 and 2 h). The adsorption isotherms have been calculated. A percentage removal of 98 % and 99 % were obtained for simultaneous removal of 50 µg/mL norfloxacin and paroxetine, respectively in 2 h. Monitoring norfloxacin and paroxetine concentrations was performed through a validated HPLC-DAD method. The reusability of the nanoparticles has been studied for 3 adsorption–desorption cycles. No significant loss in adsorption efficiency was observed offering a sustainable water treatment. This study would offer a facile, green and economic protocol for the removal of complex organic compounds from water resources.

In-situ bioprocessing of bacterial cellulose aerogel with covalent organic frameworks for enhanced uranium extraction

Developing efficient and cost-effective uranium adsorbents remain a significant challenge due to the complex composition of seawater. Herein, this study for the first time utilized an in-situ spray gel-assisted biosynthesis strategy to homogeneously incorporate the covalent organic frameworks (COF) into the three-dimensional pores of bacterial cellulose (BC) hydrogel during the culture of K. sucrofermentans. The BCCOF-SO3NH4 aerogel was fabricated through ammoniating modification of BC/COF (BCCOF-SO3H) hydrogel and freeze-drying processes. The BCCOF-SO3NH4 aerogels are characterized by the in-situ entanglement of COF within the three-dimensional network of BC, resulting in enhanced mechanical strength and groups interactions. The experimental maximum adsorption capacity of BCCOF-SO3NH4 aerogel reached 883.44 mg g−1, demonstrating exceptional uranium adsorption capacity compared with most of the reported adsorbents. The adsorption process follows the pseudo-second-order model and Langmuir isotherm. Throughout seven adsorption–desorption cycles, BCCOF-SO3NH4 maintained a stable adsorption capacity and desorption efficiency. The adsorption mechanism is verified by experiments and DFT calculations, which involves not only the ion exchange between uranyl and NH4+, but also the strong coordination interaction between the active groups (sulfonic acid group, hydroxyl group) and uranium. The in-situ biosynthesis strategy of composites shows a great application prospect in the preparation of high adsorption performance materials.

Hierarchically porous MgO/biochar composites for efficient CO2 capture: Structure, performance and mechanism

For enhancing the CO2 uptake performance of MgO-based materials, hierarchically porous MgO/biochar composites were prepared using a microwave-assisted hydrothermal method. The CO2 adsorption properties was investigated in detail and the adsorption mechanism was revealed by considering structure − function relationships and performing density functional theory calculations. The MgO/biochar-1 had hierarchical pore structure and high specific surface area (1453 m2·g−1) with abundant narrow micropores (<1.0 nm), facilitating the adsorption of CO2. The results demonstrated that MgO/biochar-1 exhibited the highest CO2 capture capacity of 6.65 mol⋅kg−1 (273 K, 1 bar) and excellent selectivity for CO2/N2 (96.70 at CO2/N2 = 15:85, v/v). After 3 cycles, the adsorption capacity of MgO/biochar-1 still remained at 5.70 mol⋅kg−1 (273 K, 1 bar), suggesting the well cycling performance. The results of density functional theory calculation indicated that the oxygen-containing functional groups and MgO particles substantially enhanced the CO2 capture performance due to the enhanced interactions between MgO/biochar and CO2. This study provides novel insights for the construction of efficient and cheap solid adsorbents for CO2 capture.

Mechanism of one-step hydrothermal nitric acid treatment for producing high adsorption capacity porous materials from coal gasification fine slag

The increasing amount of coal gasification fine slag (CGFS) necessitates its resource utilization. CGFS, mainly composed of porous carbonaceous particles and partially fused spherical or agglomerated ash particles, is an inexpensive and high-quality raw material for preparing adsorbent materials. However, the challenge remains in developing a simple, low-cost, and environmentally friendly method to produce high-performance porous materials from CGFS. In this study, a one-step treatment method using 2 mol/L nitric acid under hydrothermal conditions was proposed for CGFS. The adsorbent material (CGFS-2 M) prepared under a solid–liquid ratio of 2:5 and an initial concentration of 200 mg/L methylene blue (MB) exhibited an equilibrium adsorption capacity as high as 210.20 mg/g. The excellent adsorption performance of CGFS-2 M can be attributed to several factors: acid leaching for mineral removal and pore formation, resulting in a specific surface area and total pore volume 2.2 and 1.6 times that of untreated CGFS, respectively, and an optimized mesoporous pore size distribution favorable for MB adsorption; optimal mineral removal and a well-defined carbon microcrystal structure providing more space for MB adsorption; nitric acid treatment increasing the surface oxygen content and hydrophilicity, enhancing its ability to remove MB. The synergistic effect of pore structure improvement and surface modification indicates a feasible research direction for enhancing the performance of CGFS-based adsorbent materials. These results provide theoretical support for the development of efficient CGFS-based adsorbents.

In-situ induced formation of Fe-OM association in soil: Theory and practice of remediation of cadmium contaminated paddy fields in high cadmium geological background areas

Cadmium (Cd) pollution in rice paddies, attributable to high geological Cd backgrounds, has emerged as a global concern. This study leverages the passivation mechanism of bioavailable Cd by iron-organic matter associations (Fe-OM) to explore a novel strategy for Cd immobilization. We examined the adsorptive capacity and removal efficiency of Cd by laccase-mediated Fe-OM association and assessed their natural stability using 57Fe isotopic tracing. Additionally, we conducted in-situ remediation trials in a Cd-enriched paddy soil. Our results indicate that the theoretical maximum adsorption capacity for Cd by the laccase-mediated Fe-OM is 100.0 mg/g, which is a 15% improvement over the common Fe-OM and a 150% enhancement over inorganic iron oxides (ferrihydrite). The 57Fe isotope tracing test showed that the affinity of laccase-modified organic matter for iron increased by 55.6%, and it exhibited better stability than common Fe-OM under anaerobic conditions. The field-scale remediation, predicated on the in situ synthesis of Fe-OM association, effectively reduced the bioavailable Cd concentration in the soil from 0.91 mg/kg to 0.40 mg/kg. Concurrently, the Cd concentration in rice grains was lowered from 0.63 mg/kg to 0.15 mg/kg, thus falling beneath the national safety threshold. This study represents a significant advancement in the safe reclamation and utilization of agricultural soils with elevated geological Cd burdens.

Synthesis, characterization, and kinetic approach of a polyvinyl chloride embedded-thiosemicarbazide sequestering agent for efficient uranium adsorption from aqueous solution

A new promising polyvinyl chloride embedded-thiosemicarbazide sequestering agent (PVC-TSC), was exploited to separate U(VI) from its water solution. Specifications for PVC-TSC were carried out efficaciously using respective performances such as BET, TGA, 1H NMR, SEM-EDX, 13C NMR, FT-IR, XPS, and GC–MS analyses, which assure a satisfactory synthesis. Variables like initial pH, agitation duration, temperature, starting U(VI) concentration, PVC-TSC dosage, co-existing ions, and eluting agents have all been fine-tuned by experimental optimization. In conditions of 298 K, pH 4.5, 30 min of agitation, and 0.63 × 10−3 mol/L uranium ions, the maximal sorption competence of PVC-TSC is 30 mg/g. Based on the adsorption-distribution isotherm estimation, the experimental value of 30.12 mg/g is similar to the theoretical value that Freundlich came up with. However, Langmuir's value is higher and more in line with the practical data. Modeling of the U(VI) kinetics adsorption by PVC-TSC yielded a theoretical retaining capacity of 29.66 mg/g for first-order (PFO) modeling and 32.051 mg/g for second-order (PSO) modeling, as suggested by a hybrid PFO and PSO kinetic model. By taking into account the thermodynamical factors ΔS° (−0.063 kJ/mol.K), ΔH° (−16.2 kJ/mol), and ΔG°, the adsorption evolution was anticipated to be exothermic, spontaneous, and best performed at down temperatures. From a cost perspective, eluting the loaded PVC-TSC composite with 0.5 M H2SO4 yields a 90 % efficiency rate for U(VI) ions.

Enhanced phosphorus removal from anoxic water using oxygen-carrying iron-rich biochar: Combined roles of adsorption and keystone taxa

Anthropogenic enrichment of phosphorus (P) in water environment can cause eutrophication, harmful algal blooms, and water quality deterioration. Adsorbents are often used for the removal and recovery of P from water, however, P is highly susceptible to re-release in anoxic benthic environments. As a response, this study prepared oxygen-carrying iron-rich biochar (O-Fe-BC) as an effective oxygen micro-nanobubble carrier (Q = 8.7024 cm³/g STP at 1.5 MPa) and P adsorbent (qm = 16.7097 mg P/g, q0.1 = 3.1974 mg P/g). Over the 90-day experimental period with O-Fe-BC, dissolved oxygen (DO) levels in the overlying water could maintain at ∼4 mg/L (peaking at ∼9.5 mg/L), and total phosphorus (TP) and soluble reactive phosphorus (SRP) levels decreased by over 96 %. The higher inorganic phosphorus content in the surface sediment-biochar mixture, along with the lower labile P and Fe concentration in the sediment pore water in the O-Fe-BC group compared to other groups, suggested the enhanced P immobilization. Further mechanism exploration revealed the combined roles of adsorption and microbial response, in which O-Fe-BC achieved efficient phosphate adsorption primarily through inner-sphere complexation via ligand exchange and keystone taxa (particularly Candidatus Electronema) played a crucial role in driving water chemistry divergence. Specially, these cable bacteria could provide large pools of Fe oxides in the surface sediment, binding with P to prevent its release, as supported by significant correlations between Ca. Electronema abundance and oxidation–reduction potential (ORP), TP, SRP, and sediment Fe-P variations. Additionally, a pot experiment with mung bean seedlings showed that the recovered O-Fe-BC significantly promoted the seed germination and growth, indicating its potential as a novel material for removing and recovering P from eutrophic waters. Taken together, our work provided a promising strategy for sustainable anoxia and P pollution mitigation, and also highlighted the indispensable roles of inner-sphere adsorption in P recovery and microbial keystone taxa in P cycling regulation.

Synthesis of ZIF-8/chitosan composites for Cu2+ removal from water

ABSTRACT In this work, a kind of novel Chitosan (Cs)-doped zeolite imidazole framework (ZIF-8@Cs) with a larger surface area and a smaller pore size was synthesised via a facial solvothermal approach and applied to remove Cu2+ from mine wastewater. Compared to nondoped ZIF-8, ZIF-8@Cs exhibited a stronger adsorption performance and removal efficiency. The reason was that ZIF-8@Cs doped by the Cs could suppress the aggregation and increase the monodispersity of ZIF-8. Using the high-performance ZIF-8@Cs, as a novel adsorbent, was successfully developed for the efficient removal of Cu2+ from mine wastewater. Various parameters, such as contact time, initial Cu2+ concentration, adsorbent dosage, and pH, were investigated. The results showed that a removal efficiency of 85% was obtained at 4 h contact time for a Cu2+ concentration of 30 mg/L at the optimum pH of 6.0. Equilibrium data were analysed using different isothermal models and kinetic models, analytic results indicated that the capture of Cu2+ by ZIF-8@Cs could favourably comply with the pseudo-first-order kinetic model and Langmuir isotherm model. The single-layer adsorption of Cu2+ on ZIF-8@Cs was dominated by diffusional mass transfer. Additionally, the results of the thermodynamic analysis indicated that the adsorption of Cu2+ by ZIF-8/Cs was a spontaneous, exothermic, and ordered process. Overall, the results reported herein indicated that ZIF-8/Cs with high adsorption efficiency are very attractive and imply a potential practical application for the removal of potentially toxic elements in wastewater.

Novel utilization exploration for the dephosphorization waste of Ca–modified biochar: enhanced removal of heavy metal ions from water

Phosphorus-modified biochar has been proven to enhance the precipitation and complexation of heavy metal ions from wastewater. However, the current modification methods require large amounts of exogenous P and have high energy consumption. Hence, this study proposes and analyzes a strategy integrating biochar production, phosphorus wastewater treatment, dephosphorization waste recovery, and heavy metal removal. “BC-Ca-P” was derived from Ca-modified biochar after phosphorus wastewater treatment. The adsorption of Pb(II) by BC-Ca-P followed the Langmuir isotherm and pseudo–second–order kinetic models. The maximum adsorption capability of 361.20 mg·g−1 at pH 5.0 for 2 h was markedly greater than that of external phosphorous-modified biochar. The adsorption mechanisms were dominated by chemical precipitation and complexation. Furthermore, density functional theory calculations indicated that oxygen-containing functional groups (P-O and C-O) contributed the most to the efficient adsorption of Pb(II) onto BC-Ca-P. To explore its practical feasibility, the adsorption performance of BC-Ca-P recovered from an actual environment was evaluated. The continuous-flow adsorption behavior was investigated and well-fitted utilizing the Thomas and Yoon–Nelson models. There was a negligible P leakage risk of BC-Ca-P during heavy metal treatment. This study describes a novel and sustainable method to utilize dephosphorization waste for heavy metal removal.Graphical