Particle Capture Efficiency Research Articles

Effect of seasonal changes in temperature on capture efficiency in the blue mussel, Mytilus edulis, fed seston and microplastics

AbstractSuspension‐feeding bivalve molluscs are dominant benthic fauna in many near‐shore environments, with phytoplankton often being their main prey type. Feeding, which involves hydrosol filtration and mucociliary processes to capture particles and process them for digestion, occurs at low Reynolds numbers. Changes in water temperature have been shown to affect feeding processes of bivalves as a result of altered physiological processes or temperature‐dependent changes in kinematic viscosity of water. Most studies, however, have focused on feeding rates and have manipulated temperature under laboratory conditions. In this study, experiments were conducted using ambient seawater and acclimatized blue mussels, Mytilus edulis, to examine particle capture efficiency over a 1‐year period. During this period, water temperature decreased from ~18°C to 5°C with a concomitant increase in viscosity of ~41%. The capture of a wide variety of bacteria and phytoeukaryotes (0.8–8 μm), as well as two sizes of polystyrene microspheres (1 and 6 μm), was quantified to calculate capture efficiency. Data demonstrate that temperature, and the concomitant change in water viscosity, had no significant effect on capture efficiency. Cyanobacteria were captured at significantly higher rates than other bacteria of similar size. These results suggest that the laterofrontal cirri of blue mussels act as paddles rather than sieves because capture efficiency was constant over a range of viscosities and Reynolds numbers. Additionally, the efficient capture of some bacteria and smaller phytoeukaryotes by the mussels suggests that these plankters could play a larger role in the diet of M. edulis than previously considered. The ecological impact of these findings, especially regarding differences in capture efficiency of different bacterial cells, warrants further study.

High-temperature deposition model for molten particle prediction based on droplet-surface interaction criteria

Particle deposition in gas turbine engines damages blade surfaces and diminishes engine performance. Deposition results from heat and momentum exchanges between fluid and particles, coupled with the interactions between particles and surfaces. The increasing turbine inlet temperatures cause particles to become molten, complicating their interaction with surfaces. Existing models fail to convincingly explain the deposition behaviors of molten particles. In the present study, considering particle fluidity and the nonlinear accumulation of deposits, the deposition criteria for viscous droplets and the maximum steady deposit layer model were incorporated to establish an unsteady high-temperature deposition model. The new model, validated against experiment results in the literatures, predicts molten particle deposition behavior with an average error of 3.89 % in capture efficiency at high-temperature conditions. It accurately predicts crown-like deposit morphology and nonlinear accumulation, matching experimental observations. Applied to nozzle guide vanes with film cooling, results show that deposits primarily occur on the leading edge and pressure side near the trailing edge. The particle capture efficiency initially rises before diminishing as particle size increases, whereas an inverse trend is noted with the escalation of the mass flow ratio. At a mass flow ratio of 0.15, the capture efficiency hits the minimum of about 13.2 %.

Enhancing capture efficiency of drug-carrier particles in the carotid sinus by utilizing a combination of magnetic fields: A numerical approach

Magnetic drug targeting is a relatively new method to treat vascular occlusion in different body parts. However, the effectiveness of this method can be affected due to the severity and location of the occlusion. This can lead to the injection of high dosages of drugs, which can cause serious side effects due to the deposition of drugs in unwanted parts. To mitigate these effects, this study investigates the potential of a guiding magnetic field in enhancing drug absorption for vascular occlusion treatment. The method relies on guiding magnetic nanoparticles (NPs) loaded with drugs toward the occlusion site using two external magnetic fields. Blood flow was modeled as non-Newtonian, considering shear-rate-dependent viscosity and unsteady at the inlet. To test this idea, a computational fluid dynamic (CFD) coupled with a discrete phase model (DPM) approach has been employed to simulate drug delivery in three-vessel structures with varying degrees of occlusion (45 %, 60 %, and 90 %). To avoid the escape of drug carriers, a secondary magnetic field was applied at the bifurcation point to direct the NPs to the site of blockage where the primary magnetic field acts. Then, the states with or without a guiding source at the bifurcation site are compared based on the capture efficiency of each structure. The simulation demonstrated a significant increase in NP capture at the target site, ranging from 2 % to 15 %, depending on the NP size. However, the severity of occlusion substantially impacted the secondary magnetic field's effectiveness. In the 90 % occlusion scenario, the method's efficiency decreased significantly from 26 % to 16 % for NP sizes exceeding 1.5μm. This study highlights the potential of guiding magnetic fields in improving drug delivery to target sites in vascular occlusion.

Fluid-structure interaction of flexible collectors affects particle capture efficiency at ecologically relevant collector Reynolds numbers

Introduction: The capture of suspended particles, which is an important process in many aquatic and terrestrial ecosystems, has been modeled using stationary rigid collectors and, more recently those that move in response to flow-induced vibrations. These models do not, however, account for collector flexibility, despite the fact that many biological collectors, especially aquatic collectors, exhibit flexibility.Methods: This study examined the effect of collector flexibility (indicated by the Young’s Modulus, E; range = 10–3–102 GPa) on particle capture efficiency (η; flux of captured particles: flux of particles) at different collector Reynolds numbers (Rec where the collector diameter [dc] is the length scale; range = 30–508) in a recirculating flow chamber.Results: Patterns in η were generally similar for flexible and rigid collectors until moderate Rec (∼374) when higher η were observed on the most flexible collectors. This threshold corresponded to periods of vortex induced motions in which the oscillation frequency of the collector transverse to the flow direction was >4 Hz and the maximum amplitude of the oscillation relative to dc was >60% in the transverse and >100% in the longitudinal direction.Discussion: Given the range in E examined in this study, it is likely that particle capture on flexible natural collectors has been underestimated using the standard model of a rigid stationary or oscillating collector. The role of collector flexibility should be considered in models and studies of particle capture in natural systems.

Biodegradable Biconstituent Melt-Blown Nonwovens for Air Filtration: Fabrication and Characterization

Melt-blown polypropylene (PP) is extensively used in air filtration due to its low cost, low weight, and easy processing, but there are increasing environmental concerns due to its non-degradability. On the other side biodegradable polymers such as polylactic acid (PLA) present insufficient strength and limited toughness. Polymer blending is a well-known approach to reach optimum properties from at least two polymers. This study aims to produce biodegradable PP-PLA-based filter materials that possess enhanced elasticity and superior filtration performance. The addition of PLA raises the average fiber diameter (AFD), causing the PP-PLA filters to have AFD ranging from 0.73 to 0.91 μm. However, the incorporation of zinc stearate (ZnSt) decreased the melt viscosity, resulting in thinner fiber formations with AFD ranging from 0.6 to 0.75 μm for PP-PLA-ZnSt. The efficiency of the corona-charged optimized sample (double-layer 75PP-25PLA-ZnSt) showed 97.42% particle capture efficiency and filtration performance of 0.12 mmH2O−1. Despite the presence of hydrophobic surfaces in all filter materials, the addition of ZnSt further improves the resistance to surface wettability. 75PP-25PLA-ZnSt filter material exhibits high stretchability, with a maximum tensile strength of 380 ± 70 kPa. The proposed tricomponent (PP-PLA-ZnSt) approach would be used to reduce the environmental impact of non-degrading polymers.Graphical abstract

Design and Analysis of Gas Cyclone with Arc-Shaped Cone Using Bézier Curve for Improved Performance

Abstract The research investigates novel gas cyclone separators with curved conical sections, comparing eight configurations with varying curvature sizes. Gas cyclones are traditionally used as particle separators to remove dust from gas streams, aiming to achieve a dust-free gas flow at the exit pipe while recovering particles to the dust outlet. Computational fluid dynamics (CFD) was employed to model the gas cyclone using the Reynolds stress turbulence model (RSM); the study examines flow fields and pressure losses. It finds that increased curvature correlates with reduced pressure drop. The curved profile is derived from the Bézier curve, characterized by a set of control points determining its shape. This study examines eight cyclone configurations with the intermediate point placed at varying fractions of the main radius: 1/8, 1/4, 3/8, 1/2, 5/8, 3/4, 7/8, and the main radius itself. The investigation focuses on the impact of different conical segment shapes on cyclone performance, highlighting how convex variants outperform others at higher flow rates while concave variants exhibit higher pressure drop. The pressure drop in the convex variant with an intermediate point position equal to the main radius decreased by 50%. These findings suggest the potential of the convex variant in certain operating conditions over traditional designs with improved particle capture efficiency.

Charge Protection in Electret Air Filtration Nonwoven Materials

AbstractNonwoven media used as electret air filters are often embedded with charges to improve particle capture efficiency. These charged filters are invariably exposed to low surface tension fluids such as oils and alcohols leading to charge loss. In this study, filtration media are endowed with charge protection through increased surface repellency using melt additives that can migrate to the surface during processing. Nonwovens containing fluorochemical melt additives are produced, and examined to determine the relationship between surface chemistry, isopropyl alcohol (IPA) repellency, resultant charge retention, and filtration characteristics. Surface fluorine/carbon (F/C) ratios of ≈0.2 are sufficient to protect filtration performance from vapor discharging methods. Samples with bulk additive loadings of 1.2% or higher are found to achieve the necessary repellency to resist discharging independent of the migration state of the sample, while samples loaded at the 0.6% level required sufficient migration to achieve the requisite F/C ratio of 0.2 in order to be protected. Samples that achieved the necessary surface chemistry to provide significant IPA repellency retained > 80% of electret charge and corresponding filtration performance. These results have special significance in the design of filtration media relevant in global healthcare and other industrial settings.

Evaluation and prediction of fibrous filters' operating performance in residential fresh air system

Fibrous filters play a crucial role in determining indoor air quality and protect people from bacteria, particulates, and viruses such as COVID-19. However, there is a lack of comprehensive research on methods for effectively evaluating and predicting the operating performance of these filters. In this study, we conducted laboratory and field tests on coarse (G4) and medium (F9 or F7) filters from four different brands to assess both their initial and operating performance. We discovered that a fluffy fiber structure in coarse filters could achieve an impressive threefold increase in dust holding capacity (DHC) compared to normal filters. Utilizing initial pressure drop, initial particle capture efficiency, and DHC, we introduced a new quality factor (QF) that integrates these parameters to evaluate the filter's long-term performance. This approach addresses the limitations of traditional quality factor, which neglects DHC and tends to underestimate the performance of filters with high DHC. Additionally, we proposed a simple method to predict the filter's operating pressure drop, using particle concentration data from weather report. This allows for convenient assessment of the fresh air system's operating status, offering potential integration into a user-friendly mobile application or computer software. These findings contribute innovative ideas for enhancing the intelligent and energy-efficient operation of fresh air systems.

Development of Cellulose Air Filters for Capturing Fine and Ultrafine Particles through the Valorization of Banana Cultivation Biomass Waste

Outdoor and indoor atmospheric pollution is one of the major problems that humanity continues to face. As a mitigation pathway, numerous technologies have been developed for air purification, including the use of fibrous filters. In this study, the particle capture efficiencies and pressure drops of air filters manufactured with cellulose pulp extracted from banana pseudostems were studied across three particle size ranges (PM10, PM2.5, and PM1). Two pretreatments were applied, alkaline with soda-antraquinone (alkali-treated pulp) and a subsequent bleaching process (bleached pulp), and four manufacturing processes were tested: crushing, freeze-drying, vacuum filtration, and pressing. In addition, a study varying filter grammage (70, 100, and 160 g·m−2) and pressing pressures (2, 4, 6, and 8 t) was also performed. After conducting these particle tests, the filter manufactured with bleached pulp, having a grammage of 160 g·m−2 and pressed at 4 t, was deemed the optimal individual solution. It demonstrated high particle retention efficiencies across all particle size ranges (with values exceeding 80%), a moderate pressure drop below 1000 Pa, and high thermal stability (degradation above 220 °C). However, combining freeze-drying and two-ton pressing processes yielded improved results (83% for the smallest particles and 89% for others) with approximately half the pressure drop. Based on these results, this study stands as a noteworthy contribution to waste valorization and the advancement of environmentally friendly materials for particle air filters. This is achieved through the adoption of simple and cost-effective technology, coupled with the utilization of 100% natural agricultural waste as the primary manufacturing material.

The Effect of the Non-Newtonian Behavior of Blood on Capture Efficiency of Particles in a Vessel with a Local Symmetrical Stenosis

The Effect of the Non-Newtonian Behavior of Blood on Capture Efficiency of Particles in a Vessel with a Local Symmetrical Stenosis

Influence of Acoustic Streams on the Efficiency of Ultrasonic Particle Agglomeration

The article is devoted to the study of ultrasonic agglomeration of PM 2.5 in homogeneous and inhomogeneous ultrasonic fields. The possibility of increasing the efficiency of ultrasonic agglomeration by initiating acoustic streams in a resonant inhomogeneous ultrasonic field is shown. A inhomogeneous ultrasonic field with zones of high and low sound pressure levels formed using a bending-oscillating disk transmitter made it possible to initiate acoustic vortex-type streaming that promotes the movement of particles into the nodal areas of a standing wave and between them. Due to the formation of a inhomogeneous ultrasonic field, the efficiency of particle collection is increased: for PM 2.5, the efficiency reaches 95%; PM 1.5—92%; PM 0.5—85%. The results were obtained under the following conditions: concentration 2 × 10−2 g/m3, sound pressure level 165 dB, flow rate 6.2 m3/h. For comparison, when a homogeneous ultrasonic field is formed in the agglomeration chamber (under similar conditions), the efficiency of particle capture by inertial gas cleaning equipment does not exceed the following: for PM 2.5—89%; PM 1.5—85%; and PM 0.5—76%. The obtained research results made it possible to propose a design for an agglomeration chamber that can greatly increase the productivity of ultrasonic flow processing.

Analysis and research on inherent angle ventilation control of residential kitchen range hoods

The emission of oil fume particles during kitchen cooking processes constitutes a significant factor that impacts indoor air quality and human health. Range hoods, as indispensable ventilation devices in kitchens, play a crucial role in reducing indoor particle concentrations. This study employs a combined approach of orthogonal experiments and computational fluid dynamics simulations to investigate the exhaust characteristics of inherent-angle-measurement-based range hoods. It analyzes the diffusion patterns of cooking-generated particulate matter under various cooking scenarios, considering factors such as the opening and closing of windows, cooking source velocities, and different airflow rates of the range hood. Based on different airflow organization patterns, a supplementary ventilation system is designed. The rationality and effectiveness of the supplementary ventilation system are analyzed to establish an effective control scheme for reducing particulate matter in various kitchen environments. The simulated research results indicate that particles disperse along the inclined surface of the side-draft range hood, resulting in higher pollutant concentrations in the breathing zone compared to the cooking zone. Increasing the exhaust airflow rate of the range hood enhances particle capture efficiency by 9.8 %. The induced airflow generated by opening windows improves particle capture efficiency by 12.9 %. However, when the velocity of the window-induced airflow exceeds 1.5 m/s, it hampers the promotion of particle capture efficiency. In the case of windows being unconditionally open, implementing a ceiling-mounted supplementary air supply system effectively improves the kitchen's particle concentration, achieving a maximum particle capture efficiency of 97.66 %. When windows can be opened, setting a baffle on the range hood, the simulation results revealed that with a baffle angle of 120° and a length of 0.3 m, the particle concentration capture efficiency in the breathing zone increased by 34.59 %. This achieved the standard limit requirement of 50 µg/m3, thus meeting the indoor air quality requirements.

Modelling the Spatial Distribution of Industrial Facilities and Green Areas to Reduce the Ecological Footprint

The work solves conjugated problems of a stationary and non-stationary nature for the processes of transfer and diffusion of harmful substances into the atmosphere emitted by industrial facilities to protect the ecology and environment from man-made factors. When mathematically modelling mass transfer in air, absorption coefficients were considered depending on climatic conditions and external disturbances, as well as adhesion coefficients of aerosol particles with vegetation and other weather and climatic factors. Analytical solutions and dual functionality were obtained, and solutions have been developed to optimize the location of industrial facilities in the region from the perspective of economic development and environmental protection. Numerical calculations have shown that the efficiency of particle capture by vegetation is a key factor depending on the type and size of vegetation and varying throughout the year. Experiments have confirmed that the concentration of harmful substances in the ground layer of the atmosphere decreases with increasing coefficients of absorption and capture of particles by vegetation. Computational experiments carried out on a computer have established that with an increase in the diffusion coefficient, the zone of distribution of pollutants expands.

Designing Multi-Layer electret filters via numerical simulation

The deposition of neutral and charged particles inside an electrostatically charged filter can affect its performance by decreasing its ability to capture additional particles and by increasing its pressure drop. The particle-loaded behavior of a composite filter comprised of three fibrous layers is studied in this paper using a macroscale simulation approach. Each of these fibrous layers were assumed to have fibers with the same amount of charge but different charge polarities of only unipolar positive, only unipolar negative, or only bipolar. The charged layers were stacked on top of one another in three different configurations with respect to the flow direction and their filtration efficiency and pressure drop were compared during particle loading with neutralized particles (having the Boltzmann equilibrium charge distribution), singly-charged particles, and neutral particles. Our simulations revealed that placing the bipolarly-charged layer downstream of the unipolarly charged layers helps to lower the negative impact of particle deposition on pressure drop and filtration efficiency of the resulting composite filter. This study introduces a design tool which can be used to optimize the configuration of a composite filter for enhanced particle capture efficiency and reduced pressure drop increase.

Pulsatile blood flow simulations of magnetic drug targeting (MDT) for drug particles dispersion through stenosis asymmetric and symmetric vessels

Magnetic drug delivery has emerged as an innovative strategy for addressing medical conditions like tumors and vascular occlusions. In this study, we delve into the influence of magnetic fields on three-dimensional models representing various vessel configurations, including unobstructed, asymmetric, and symmetric vessels. We take into account critical factors such as non-Newtonian viscosity, pulsatile flow, and the presence of vessel obstructions. By investigating drug particles ranging from 1 to 4 µm in diameter, our findings illuminate the central role that magnetic particles play in Magnetic Drug Targeting (MDT). Importantly, we observe a substantial enhancement in drug particle capture efficiency in the presence of a magnetic field, particularly for larger particle diameters. Nevertheless, this efficiency saturates at 100% for diameters exceeding 3 µm due to particle–wall interactions. Interestingly, within potential obstruction areas, particle capture efficiency exhibits a nuanced relationship with diameter. Even at a diameter of 4 µm, the magnetic field's influence on vessel walls leads to particle capture before reaching obstructions, thus reducing efficiency. Comparing scenarios without a magnetic field, it is found that symmetrical obstructions yield higher capture efficiency compared to asymmetrical vessels, and asymmetric vessels outperform their smoother counterparts. Moreover, the presence of vessel obstructions amplifies drug particle capture efficiency. Consequently, our simulations unveil significant potential for the application of MDT in the treatment of atherosclerosis. From a physics perspective, these results offer promising prospects for the application of Magnetic Drug Targeting in the realm of cardiovascular diseases.

The Numerical Investigation of Solid–Liquid Two-Phase Flow Characteristics Inside and Outside a Newly Designed 3D Sediment Trap

Sediment transport serves as a link for material exchange between land and sea. Using sediment traps, we can observe the capture and transport processes of sediments. Based on the sediment particle size distribution characteristics in Jiaozhou Bay, this paper analyzes the influence of a newly designed 3D sediment trap on the water–sand two-phase flow process inside and outside a trap device during its operation. Meanwhile, under a certain concentration condition, a numerical formula model is researched and proposed to evaluate the impact of the device’s structure, the environmental flow speed, and the particle size on particle capture efficiency. This model is based on the CFD-DPM coupling in Fluent 2021R1 software, and the particle filtration process is solved using a combination of porous media and UDF functions. Finally, by analyzing the distribution of sediment movement in the fluid domain, two concepts, namely the percentage of particles entering the tube and the effective capture rate, are proposed. Suggestions for optimizing the structure of the trap are put forward to achieve optimal capture effects.

Characteristics of ash formed by different lubricant additives and its effect on DPF performance

Diesel Particulate Filter (DPF) is an important technology to reduce diesel exhaust particles. The ash formed by the combustion of lubricant oil will be deposited in the DPF, which will affect the filtration efficiency of DPF. In this paper, the ash generated in the burner by combustion of two lubricant additives mixed with diesel fuel were obtained by the burner test of ash rapid loading. The microscopic morphology of ash was studied by scanning electron microscopy and the fractal dimension was calculated based on fractal theory. Chemical composition analysis was performed using energy-dispersive X-ray spectroscopy. The filtration efficiency of DPF was tested with EEPS 3090 when loaded with different ash fractions. The results show that the average fractal dimension of Mg-based ash (1.5791) is higher than that of Ca ash (1.5420), indicating a more detailed surface structure at the microscopic level. This suggests that Mg-based ash is more likely to plug, sinter and even form bridging phenomenon in the DPF inlet channel. The filtration efficiency of DPF increases and then decreases with the loading of ash. The capture efficiency of large particles of 40–200 nm is increasing with the loading of Ca-based ash. However, due to the higher fractal dimension, the loading of Mg-based ash can significantly improve the capture efficiency of small particles of about 10 nm. This work is beneficial to explain the influence of ash on the efficiency of DPF in filtering particles of different sizes.

High-gradient magnetic separation of colloidal uranium oxide particles from soil components in aqueous suspensions

The separation of uranium oxide (UO2) particles from soil-surrogate particles in aqueous suspensions was achieved using filtration enhanced by a magnetic field. Enhanced attraction of paramagnetic UO2 colloids to a ferromagnetic stainless-steel filter placed in a strong magnetic field arises because of the positive magnetic susceptibility of the particles and the high-gradient field generated near ferromagnetic fibers. Enhanced uptake of smaller particles over larger ones occurs through Brownian motion that promotes the collision of particles with the ferromagnetic fibers of the filter. Hence, this work focused on UO2 particles in the colloidal size range. Experiments used a water-cooled electromagnet and an array of permanent magnets. Chemical analysis showed that the magnetic field increased the capture efficiency of uranium particles from a range of 27–53% with the magnet off up to 98% with the magnet on after a single pass of the suspension through the filter. The recovery of the UO2 particles from the filter, however, was more difficult to achieve. Small amounts of UO2, together with significant amounts of background SiO2 particles, were removed from the filter during a first flush with the magnetic field on. A much larger recovery of UO2 was not observed until a second out-of-field flush was performed, which also released some SiO2. The degree to which particle separation was enhanced through the use of multi-stage filtration compared to single pass-through filtration was also examined. A design was suggested that could be used to optimize the separation efficiency for a continuous process.

Inertial capture of aerosol particles using liquid bridges in cross flow

We investigate the inertial capture of aerosol particles, suspended in a laminar cross flow between parallel plates, by stationary cylindrical liquid bridges. We track the motion and fate of individual aerosol droplets (3–9 μm diameter) suspended in a flow moving across a single liquid bridge or two-bridge systems, using high-speed imaging under a microscope. First, we measure the capture efficiency by inertial impaction of an isolated liquid bridge collector as a function of the aerosol particles Stokes number and show that it agrees with the efficiency calculated for rigid particles moving in a potential flow past a solid cylinder. We then consider two-bridge systems, that is two parallel cylindrical collectors oriented perpendicular to the flow, but offset from each other. We investigate the effect that the upstream collector has on the effective capture efficiency of the downstream test collector, depending on the transverse offset and Stokes number. The offset is the relative displacement of the downstream collector normal to its axis and in the direction perpendicular to the freestream flow. For small values of the transverse offset, smaller than the radius of the collector, small (zero) effective efficiencies are measured for the test collector, due to a partial (complete) shielding effect by the upstream collector. The effective efficiency thus increases from zero with increasing transverse offset, above a threshold value for complete shielding. As the transverse offset increases further, effective efficiencies larger than the efficiency of an isolated bridge are measured for the test collector, showing enhanced capture due to the redistribution of particles moving past the upstream collector. The relative increase in the inertial capture efficiency is significant for Stokes numbers around (but below) unity, 0.45≲St≲0.9, with relative gains as large as approximately 50%. There is an optimum offset displaying maximum effective efficiency and larger offset values lead to a slight decrease in measured efficiencies. These results demonstrate the importance of the relative arrangement of individual collectors on the overall inertial capture efficiency of aerosol particles and suggest that an array of bridges in a slanted configuration (with optimal transverse offsets) could be used as a high-performance filtration system for aerosol particles.

Dimensional analysis of magnetophoresis

Magnetophoresis is used in various applications requiring selective collection of magnetic particles. This study is aimed at quantitatively describing magnetophoretic systems via dimensional analysis to assess the relative contribution of hydrodynamics, electromagnetism, and particle dynamics. We introduce dimensionless numbers characterizing the transport of magnetic particles in a fluid. Analytical and numerical studies were conducted for magnetophoretic systems where magnetic particles were suspended in a fluid exposed to magnetic fields generated by permanent magnets. The magnetically induced mobility of the magnetic particles was simulated for a range of parameters relevant in biomedical applications, including the particle and fluid properties, flow velocity, and geometries of the particle, flow channel, and magnet. The numerical results obtained in multiphysics modeling of magnetophoretic systems were analyzed based on the proposed dimensionless numbers, resulting in a functional relationship for the particle capture efficiency (CE), defined as the ratio of captured particles to all particles injected in the flow. The performance of magnetophoretic systems predicted with the dimensional analysis was verified in comparison with published experimental data. Using dimensional analysis, 12 input parameters determining the particle CE were reduced to 3 dimensionless numbers characterizing the ratios of magnetophoretic and hydrodynamic forces, cross-sectional areas of the magnet and the flow channel, and length and diameter of the magnet. A set of curves predicting particle CE was obtained using these dimensionless numbers. A close agreement was found between the CEs predicted by the curves and those obtained in both numerical simulations and experiments where cylindrical magnets were placed in a flow through a cylindrical pipe. This study provides a promising framework for analyzing and predicting performance of various magnetophoretic systems for a range of applications.