Effective Viscosity Research Articles

Effect of resin cement viscosities and surface roughness on shear bond strength of conditioned polymer infiltrated ceramic network

BackgroundHybrid ceramics bonding with the dentinal substrate is crucial for clinical success and longevity. To enhance adhesion, the surface of ceramic restorations is modified through various conditioning techniques AimEffect of Different Surface Conditioners Erbium-doped yttrium aluminum garnet (ER: YAG) laser and Low-level laser therapy (LLLT) activated Methylene blue (MB) on the surface roughness (Ra) and shear bond strength (SBS) of Polymer infiltrating ceramic network (PICN) discs bonded using different viscosity resin cement before and after thermal aging. Material and MethodsOne hundred and fifty human central incisors and one hundred and fifty-three PICN discs were prepared. PICN discs were randomly allocated into three groups based on the surface conditioning(n = 51) Group 1:10 % HF acid-S, Group 2: LLLT (MB), and Group 3: Er: YAG laser. Following conditioning Ra scores of ten samples were performed. Surface topography of samples was performed using a scanning electron microscope (SEM). Bonding of forty PICN discs from each conditioning group was performed with high (A) or low viscosity (B) dual-curing resin cement (n = 20 each). Each subgroup was divided into two cohorts and subjected to varying storage conditions. The SBS test and failure mode analysis were performed using a universal testing machine and stereomicroscope. Descriptive statistics of SBS and Ra for each group were analyzed using ANOVA and Tukey post hoc tests. HF acid-S attained the highest Ra scores. ResultsGroup 1A (HF-S+HIGH) samples achieved the highest SBS values at baseline. Group 3A, on the other hand, displayed the lowest bond score (Er: YAG laser+HIGH) after thermal aging. Intergroup comparison analysis at baseline unveiled that Group 1A and Group 1B (HF(S) + LOW) displayed no significant difference in their bond strength scores (p>0.05). Following artificial aging, it was observed that Group 2A (LLLT (MB) + HIGH) and Group 3A (Er:YAG laser + HIGH) ) presented comparable SBS(p > 0.05). Thermal aging decreased SBS significantly in all groups. PICN conditioned with HF-S results in high surface roughness. ConclusionPICN conditioned with HF acid with silane and bonded with low-viscosity resin cement to the dentinal substrate is preferable. Aging influences SBS.

The Influencing Factors and Mechanism of Anionic and Zwitterionic Surfactant on Viscosity Reduction in Heavy O/W Emulsions.

The high viscosity of heavy crude oil has been an obstacle to its safe production and economic transportation. In this work, a screened emulsified viscosity reducer system is conducted. Experimental results demonstrate that the most effective viscosity reducing agent comprises sodium oleate (NaOl) and cocamidopropyl betaine (CAB-35) in a ratio of 1:2, achieving a viscosity reduction rate of 94.65%. Additionally, the interfacial tension between oil and water decreases from 27 to 4 mN/m with 0.1 mass % TEOA and NaOH in a 1:1 ratio. The oil droplet size is uniformly distributed with D mean is 14 μm and D 50 is 11 μm. Droplets flocculate as the salinity increases to 0.2 mol/L, which corresponds to the apparent increase of viscosity. The adsorption of long alkyl chain lipophilic groups on surfactant molecules at the oil-water interface and the water film alters the wettability of pipe steel to water-wet, further enhancing the application of emulsification and viscosity reduction effects. The primary mechanism behind the viscosity reduction in emulsification is attributed to strong electrostatic interactions stemming from molecular electrostatic potential distributions.

Tribological Performance of Soft Magnetic Composite Materials for Gas Turbine Applications

Abstract Soft magnetic composites (SMCs) have gained attention in the last years of their usage in more compact and powerful electromechanical systems. These materials are used to combine the application of metallic material to the capability of generating (without external supply) a magnetic field. Automotive and aerospace technologies push the applications of these original materials to even higher power and mechanical stress to reduce the number of components, the size, and, in turn, the weight of complex systems. Considering gas turbine application, SMCs were formerly developed for bearings, but in the last decades, the new era of gas turbine electrification (e.g., hybrid-electric fly) has determined the need for mechanical improvement of such materials. At the same time, the reliability of soft magnetic material has to be discovered to avoid failure and reduce the maintenance schedule. In the present work, tribological behaviors of SMCs were investigated by standard wear tests. Two different types of SMSc were prepared through the powder metallurgy technique. Tests were conducted by a tribometer using a ball-on-disk configuration in lubricated condition. The effect of oil temperature and applied load were investigated. In addition, an extensive post-mortem analysis was conducted on the worn surface to recognize the mechanisms responsible for the deterioration of the materials. The results showed the effects of the oil viscosity on the useful operating life of the SMCs. Removal mechanisms depend on the load conditions, and the proper selection of the oil characteristics and load was assessed.

A study on the combined effects of variable viscosity and thermal conductivity on forced convection in bidisperse porous medium

This research focuses on exploring the flow and temperature distribution of forced convection in a channel of horizontally placed parallel plate under the existence of a bidisperse porous medium (BDPM) emphasizing the consequences of viscous dissipation. The temperature-dependent thermal conductivity and viscosity are considered while maintaining the momentum slip and constant wall temperature at the channel walls. Analysis of the dynamics of fluid flow and the temperature distributions in both the fluid and solid phases is conducted by following the two-velocity and two-temperature models in this work. The model governing equations are non-dimensionalized following the relevant dimensionless parameters and the study calculates the temperature and velocity profiles for each phase using the Homotopy Analysis Method (HAM). The obtained temperature and velocity are discussed and explained with the help of graphs. Certain fluids exhibit varying behaviors at different temperatures. Therefore, it is crucial to consider the temperature-dependent physical properties of the fluid for specific applications. This highlights the importance of implementing temperature-dependent physical properties in the analysis. Throughout the investigation, it is discovered that the viscosity parameter has a greater influence on velocity as compared to temperature, the same for thermal conductivity on temperature. The impact of physical parameters including skin friction, volume flow rate, and Nusselt number on both plates are also examined in this study. The findings are discussed, and tables displaying numerical values for various physical characteristics are provided for both the liquid and solid phases. The results obtained were also compared with existing literature, revealing a strong alignment between them.

Effect of viscosity of gelatin methacryloyl-based bioinks on bone cells

The viscosity of gelatin methacryloyl (GelMA)-based bioinks generates shear stresses throughout the printing process that can affect cell integrity, reduce cell viability, cause morphological changes, and alter cell functionality. This study systematically investigated the impact of the viscosity of GelMA-gelatin bioinks on osteoblast-like cells in 2D and 3D culture conditions. Three bioinks with low, medium, and high viscosity prepared by supplementing a 5% GelMA solution with different concentrations of gelatin were evaluated. Cell responses were studied in a 2D environment after printing and incubation in non-cross-linked bioinks that caused the gelatin and GelMA to dissolve and release cells for attachment to tissue culture plates. The increased viscosity of the bioinks significantly affected cell area and aspect ratio. Cells printed using the bioink with medium viscosity exhibited greater metabolic activity and proliferation rate than those printed using the high viscosity bioink and even the unprinted control cells. Additionally, cells printed using the bioink with high viscosity demonstrated notably elevated expression levels of alkaline phosphatase and bone morphogenetic protein-2 genes. In the 3D condition, the printed cell-laden hydrogels were photo-cross-linked prior to incubation. The medium viscosity bioink supported greater cell proliferation compared to the high viscosity bioink. However, there were no significant differences in the expression of osteogenic markers between the medium and high viscosity bioinks. Therefore, the choice between medium and high viscosity bioinks should be based on the desired outcomes and objectives of the bone tissue engineering application. Furthermore, the bioprinting procedure with the medium viscosity bioink was used as an automated technique for efficiently seeding cells onto 3D printed porous titanium scaffolds for bone tissue engineering purposes.

Self-similar flow behind a shock wave in a gas under the effect of viscosity, heat conduction, and variable ambient density

Self-similar solutions have been investigated to describe the propagation of planar shock waves in a non-ideal gas generated by a piston under viscous stress and heat flux. The equation of state for non-ideal gas incorporates the correction in pressure and volume of the gas. The piston position and ambient density vary exponentially with time. Newton’s law of viscosity is used for the viscous stress and Fourier’s law of heat conduction is taken for heat flux. The viscosity coefficient is taken as constant whereas the thermal conductivity coefficient varies with temperature and density following the power law. The shock jump conditions have been derived for the viscous non-ideal gas using integral form of conservation laws. The shock Reynolds number Re s has been introduced to study the effect of viscosity on shock propagation in non-ideal gas. It is found that similarity solution exists only in an ideal gas under the condition that the ambient density exponent is equal to twice the shock position exponent. This study shows that shock Reynolds number Re s and heat conduction parameter Γ c can be used to control the variation of the flow variables and piston position significantly. The shock strength decreases with increase in the value of shock Reynolds number Re s but is independent of the heat conduction parameter Γ c . The pressure, density, and adiabatic compressibility have significant deviations from high to low viscous flow of ideal gas but the velocity and heat flux undergo negligible change. The results do not support the claim of negligible effect of viscosity in earlier studies and establish the impact of viscosity and heat flux on shock propagation in an ideal gas.

On Mapping Local Foam Mobility in Porous Media from Computed Tomography Data

Summary Recovering apparent viscosity and foam texture fields from coreflooding experiments is challenging, even with modern computed tomography (CT) scan equipment. In this work, we present an explicit expression for efficiently calculating effective foam viscosity and propose an improved procedure for processing CT scan images to obtain accurate water saturation profiles. Using these techniques, we processed data from a CT scan of a coreflooding experiment, showing that the increase in effective foam viscosity due to foam generation occurs early during injection and before breakthrough. The fast increment in apparent viscosity is due to foam generation before breakthrough. After breakthrough, foam texture reaches its maximum, and effective foam viscosity grows logarithmically over time as the foamed gas sweeps out the water phase. The pressure drop obtained by using the effective foam viscosity showed good agreement with the experimentally obtained values before breakthrough. The workflow proposed here could be readily adapted to other foam models, provided reasonable estimates for these new quantities can be determined from experiments.

Effect of viscosity on wind-driven gravitation waves

Effect of viscosity on wind-driven gravitation waves

Microstructural analysis on the compatibility of various dilution oils on magnetorheological grease performance

This research explores the effects of dilution oils on the storage stability of magnetorheological grease (MRG) by studying the effect of dilution oil viscosity on the microstructure of carrier fluids medium for MRG, which can help address practical challenges encountered in the development and deployment of MRG. Three samples of MRG with 70 wt% CIP are prepared; a control, and 2 samples diluted until 10 wt% hydraulic fluid and kerosene respectively. The resulting samples were analysed using a modular compact rheometer (MCR) for oscillatory strain sweep and rotational current sweep. Rheological analyses were repeated after one year in storage. Fourier-Transform Infrared (FTIR) spectroscopy and Atomic Force Microscopy (AFM) results show significant microstructural and performance deterioration of grease thickener in the sample with kerosene, which concludes that kerosene had a very significant effect on the degradation of the grease thickener. From this study, it was revealed that low viscosity oils disrupt the reconstruction of the thickener of lithium grease, which in turn causes deteriorating shear rheological performance of MRG at off-state conditions. This comprehensive analysis explains the relationships between MRG composition, microstructural characteristics, and performance parameters, offering a foundational framework for further exploration and advancement in this scientific field.

Migration characteristics of bubbles moving in gas–liquid countercurrent two-phase flow in an inclined pipe

While exploring and developing oil and gas, well kick and overflow accidents are inevitable. In such an accident, if the drilling bit is not at the bottom of the well, the drilling tool is blocked, or the reservoir contains toxic gases such as hydrogen sulfide, the traditional technique for well control is no longer suitable, and the bullheading method must be adopted to kill the well. However, during bullheading, the flow patterns of gas and liquid are intricate, making gas velocity hard to predict. To solve these problems, a set of visual simulation experimental device for directional well bullheading was built to find out the effects of wellbore inclination, liquid viscosity, gas and liquid velocities, and bubble size on bubble migration characteristics in gas–liquid countercurrent (gas flowing in opposite direction to the liquid). Prediction models of bubble distribution coefficient and rising velocity considering liquid viscosity, bubble size, and wellbore inclination angle were worked out. The experimental results show that small bubbles are mainly located in the center of the wellbore and large bubbles tend to approach the wellbore wall in gas–liquid countercurrent. Increasing wellbore inclination, viscosity, and the velocity of the liquid flowing against the bubbles results in a gradual decrease in Taylor bubble migration speed, which promotes the bubbles' pressing-back, as inhibiting the upward movement of large bubbles is essential for effective bullheading operations. The prediction models of distribution coefficient and bubble migration velocity have an error of less than 10% and 9. 78%, respectively.

Cost-effective production of density-controllable monodisperse spheres for experiments in fluids

Cost-effective production method for making density-controllable monodisperse spheres is demonstrated. A sodium alginate aqueous solution containing gelatin is emulsified with canola oil. The droplet surface is covered with a calcium alginate membrane by dropping the emulsion into a calcium lactate aqueous solution. The content of the canola oil can control the sphere's density. To demonstrate the applicability of the spheres to experimental research, rheological measurements of the suspensions of the spheres were performed. The effective viscosity agrees with the theoretical formula at volume fractions of 0.7%–11.7%. The demonstration highlights that the spheres can function as neutrally buoyant solid particles in studies for the physics of fluids.

Effects of temperature-dependent viscosity on thermal drawdown-induced fracture flow channeling in enhanced geothermal systems

Harnessing geothermal energy from an enhanced geothermal system (EGS) highly depends on fracture flow and heat transport processes. Thermal drawdown-induced thermal stress has been characterized as a major reason for severe fracture flow channeling (short-circuiting), which further leads to premature thermal breakthrough and impairs long-term thermal performance. In the present study, we quantitatively analyzed a potential flow channeling mitigation mechanism, i.e., the increase of water viscosity with temperature reduction. Through a field-scale single-fracture EGS model that incorporates thermal-hydro-mechanical coupled processes and temperature-dependent water viscosity, we demonstrate that the increase of water viscosity during heat extraction promotes a dispersed fracture flow pattern, which can effectively mitigate thermal drawdown-induced flow channeling and improve long-term thermal performance. The mitigation effect is more noticeable for homogeneous aperture scenarios than for heterogeneous aperture scenarios, especially in the early period of heat production. With a higher in-situ stress and smaller rock Young's modulus, the flow channeling effect of thermal stress becomes weak, and therefore the temperature-dependent viscosity exhibits a more significant flow channeling mitigation effect. The results from the current study provide valuable insights into the optimization of fracture flow and heat transport to achieve more efficient and sustainable energy production from EGSs.

Effect of organic solvent additives on the enhancement of ultrasonic cavitation effects in water for lithium-ion battery electrode delamination

Ultrasonic delamination is a low energy approach for direct recycling of spent lithium-ion batteries. The efficiency of the ultrasonic delamination relies both on the thermophysical properties (such as viscosity, surface tension, and vapour pressure) of the solvent in which the delamination process is carried out, and the properties of the ultrasound source as well as the geometry of the containment vessel. However, the effect of tailoring solutions to optimise cavitation and delamination of battery cathode coatings has not yet been sufficiently investigated. Acoustic detection, high-speed imaging, and sonochemiluminescence (SCL) are employed to study the cavitation processes in water-glycol systems and identify the effect of tailoring solvent composition on cavitation strength. The addition of small volume fractions of organic solvent (ca. 10–30 vol%), including ethylene glycol or glycerol, to the aqueous delamination solution were found to significantly improve the delamination efficiency of lithium-ion battery cathode coatings due to the alteration of these thermophysical properties. However, greater volume fractions of glycol decrease delamination efficiency due to the signal-dampening effect of viscosity on the ultrasonic waves. The findings of this study offer valuable insights for optimising ultrasonic bath solution composition to enhance film delamination processes.

A generalized strain model for spectral rate-dependent constitutive equation of transversely isotropic electro-viscoelastic solids

We model the constitutive equation for nonlinear electro-viscoelastic transversely isotropic solids with short term memory via a generalized strain method, where the method is a change with respect to the methods that have been done in the last decades regarding mechanics of nonlinear solids. Our generalized strain model uses spectral invariants with a clear physical interpretation and hence they are attractive for use in experiments. The constitutive equation contains single-variable functions, which are easy to deal with when compared to multivariable functions. The effects of viscosity and electric fields are analyzed via the boundary value problem results. The efficacy the proposed prototype is scrutinized by comparing our theory with experimental data.

Nonlinear stability analysis of thermal convection in a fluid layer with slip flow and general temperature boundary condition

The current article presents a comprehensive analysis of the influence of inconstant viscosity into thermal convection, incorporating the influence of generalized velocity (slip boundary condition) and temperature boundary conditions (physically represent imperfectly conducting boundary) within a fluid layer. Slip boundary conditions are often considered more practical than no-slip conditions (Neto et al. (2003)). Therefore, in the present work, slip boundary condition is used to discuss the effect of temperature and pressure dependent viscosity. Both linear and nonlinear stability analyses are explored, revealing a noteworthy finding: the precise alignment of the nonlinear stability boundary with the linear instability threshold. Additionally, the exchange of stability is illustrated, indicating that convection exclusively manifests in a stationary mode. The findings are derived across a spectrum of boundary scenarios, ranging from free-free to rigid-free, and rigid-rigid boundaries, encompassing both isothermal and adiabatic conditions. Notably, the slip length parameter exhibits a destabilizing effect, while convection is observed to occur more swiftly under adiabatic boundary conditions compared to isothermal conditions. The Chebyshev pseudo-spectral technique is applied to solve the eigenvalue problems obtained from linear and nonlinear stability analysis.

An anisotropic damage visco-hyperelastic model for multiaxial stress-strain response and energy dissipation in filled rubber

In this article, we introduce a novel physically-based anisotropic damage visco-hyperelastic model designed to predict the history-dependent inelastic behavior of multiaxially stretched filled rubber. The model integrates both the anisotropic Mullins effect and intrinsic viscosity through the consideration of internal physics, represented by two distinct networks: an elastic ground network and a superimposed viscous network. The rupture of molecular bonds within the elastic network chain backbone is modeled using statistical mechanics, while the effects of anisotropy-induced chain orientation at the upper scale are addressed through a microsphere-based scale transition method. The intrinsic viscosity is represented by the viscous network, which is governed by time-dependent equations to account for the viscous overstress. The influence of fillers is captured through the concept of strain amplification, applied to the two networks within the rubber matrix. The effectiveness of the model in capturing the biaxial behavior of filled rubber is evaluated by comparing its outputs with experimental data from a filled rubber system. This assessment specifically considers the impact of pre-stretching under various loading conditions and across a wide range of filler concentrations. Notably, it successfully predicts anisotropic stress-strain response and energy dissipation, and the coupled effects of damage and viscosity.

Linear stability analysis of the viscoelastic Navier–Stokes–Voigt fluid model through Brinkman porous media: Modal and non-modal approaches

The linear stability analysis of a viscoelastic Navier-Stokes-Voigt fluid flow, or the Kelvin-Voigt fluid of zero order in a Brinkman porous medium, is investigated using both modal and non-modal analysis. The numerical solution is obtained using the Chebyshev collocation method. The combined effects of the medium's porosity, represented by the porous parameter, the fluid viscosity, represented by the ratio of effective viscosity to fluid viscosity, and the fluid elasticity, represented by the Kelvin-Voigt parameter are investigated using both modal and non-modal analysis. The modal analysis describes the long-term behavior of the system, obtained through plotting the eigenspectrum, eigenfunctions, growth rate curves, neutral stability curves, and streamline plots, along with accurate values of critical triplets. In non-modal analysis, the pseudospectrum of the Orr-Sommerfeld operator, transient energy growth curves, and regions of stability, instability, and potential instability are depicted. The results obtained from modal analysis indicate that the porous parameter, Kelvin-Voigt parameter, and the ratio of effective viscosity to fluid viscosity act as stabilizing agents. However, using non-modal analysis, it is observed that while the porous parameter and the ratio of effective viscosity to fluid viscosity act as stabilizing agents, the Kelvin-Voigt parameter acts as a destabilizing agent over shorter periods.

Horizontal buoyant jets into viscoplastic ambient fluids

This study investigates the horizontal injection of a heavy Newtonian fluid into a lighter viscoplastic ambient fluid, in a large reservoir. The flow dynamics is experimentally captured via camera imaging, laser-induced fluorescence, and particle image velocimetry techniques. The flow parameters include various density differences, injection velocities, and ambient fluid viscoplastic properties. Our analysis identifies two key dimensionless numbers, the Froude number (Fr) and the effective viscosity ratio (m), which includes the rheology of the viscoplastic fluid. Our study also examines the effects of these dimensionless numbers on critical jet characteristics, such as bifurcation length, transition length, deviation length, and jet trajectory, and provides correlations using Fr and m, to predict these characteristic lengths. A regime classification based on the bifurcation phenomenon is also presented in the Fr−m plane.

Analysis of impulse withstand voltage of ester-based nanofluids

Ester-based nanofluids constitute an effective ecological alternative to petroleum-derived dielectric fluids for electrical engineering industry. Pulse induced dielectric breakdown is a key cause of power device failure. In this paper, we deal with the lightning impulse breakdown voltage (LI BDV) in natural and synthetic ester-based (NE and SE) nanofluids with various concentrations of magnetite (Fe3O4) and fullerene (C60) nanoparticles. The nanofluids show a decrement in positive polarity LI+ BDV as compared with the base ester. Negative polarity LI- BDV in the nanofluids is similar to that of base oils. Weibull statistical distributions are applied to analyse the results at different cumulative probabilities of 1 %, 10 %, and 50 %. Natural ester with C60 nanoparticles shows higher positive LI+ BDV values at a low probability level, while the negative LI- BDV reaches higher values at higher probability levels. The decreased LI BDV in NE and SE due to the magnetite nanoparticles are attributed to the nanoparticle clustering and percolation. The tendency of C60 nanoparticles to enhance the LI BDV in NE but not in SE is interpreted in the view of the nanoparticle concentration and oil's viscosity effect on the streamer branching and propagation.

A numerical study on MHD Casson fluid flow in a non-uniform rough channel with temperature-dependent properties using OHAM

This study explores the complex dynamics of magnetohydrodynamic (MHD) Casson fluid in a non-uniform rough channel, focusing on the effects of temperature-dependent viscosity and variable thermal conductivity under no-slip boundary conditions. The study employs an innovative approach by utilising a rough surface with irregular textures to analyse flow patterns and assess drag forces on channel objects. A novel mathematical model, governed by continuity, momentum, and heat transfer equations, is developed and transformed into dimensionless, nonlinear Ordinary Differential Equations (ODEs) using non-dimensional quantities and fundamental assumptions. The Optimal Homotopy Analysis Method (OHAM) is applied to solve these equations to enhance convergence speed and accuracy. The research explores the impact of surface roughness on velocity profiles and temperature distributions under various physical constraints. Numerical simulations are conducted to determine skin friction coefficients and Nusselt numbers. Furthermore, the study examines the influence of confined boluses on fluid flow in diverse physiological conditions. A comprehensive analysis is performed to elucidate the combined effects of surface roughness on fluid passage, including flow separation, pattern alterations, pressure distribution and drop, heat transfer characteristics, and flow resistance. The intricate interplay between temperature-dependent viscosity, varying thermal conductivity, and surface roughness is thoroughly investigated to explain the complex dynamics of MHD Casson fluid movement in non-uniform channels. Implementing a magnetic field over the rough, non-uniform channel is found to provide stability and prevent fluid overflow. This research has significant real-world applications, including soil erosion prevention, blood flow regulation in arteries, and optimisation of hydropower channels and penstocks. By enhancing our understanding of flow dynamics through rough and non-uniform channels, this study contributes valuable insights into both theoretical fluid mechanics and practical engineering applications.