Effect Of Temperature Research Articles

Temperature dependence of spin transport behavior in Heusler alloy CPP-GMR

In this study, we investigate the effect of temperature on the performance of a read sensor by utilizing an atomistic model coupled with a spin transport model. Specifically, we study the temperature dependence of spin transport behavior and MR outputs in a Co2FeAl0.5Si0.5\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$\ ext {Co}_2\ ext {FeAl}_{0.5}\ ext {Si}_{0.5}$$\\end{document} (CFAS)(5nm)/Cu(5nm)/CFAS(5nm) trilayer with diffusive interfaces. Initially, the two-channel model of spin-dependent resistivity is used to calculate the temperature dependence of spin transport parameters which serves as essential input for the spin accumulation model. Our findings demonstrate that as the temperature increases, the spin transport parameters and magnetic properties decrease due to the influence of thermal fluctuation. At a critical temperature, where the ferromagnet transitions to a paramagnetic state, we observe zero spin polarization. Furthermore, at elevated temperatures, the spin accumulation deviates from the equilibrium value, leading to a reduction in the magnitude of spin current and spin transport parameters due to thermal effects. As a consequence, the MR ratio decreases from 65% to 20% with increasing temperature from 0 to 400 K. Our results are consistent with previous experimental measurements. This study allows to deeply understand the physical mechanism in the reader stack which can significantly benefit reader design.

Effect of shear rate, temperature, and salts on the viscosity and viscoelasticity of semi‐dilute and entangled xanthan gum

Effect of shear rate, temperature, and salts on the viscosity and viscoelasticity of semi‐dilute and entangled xanthan gum

Effect of Tempering Temperature on the Aqueous Corrosion Resistance of 9Cr Series Heat-Resistant Steel

In this investigation, the aqueous corrosion resistance of 9Cr series heat-resistant steel during tempering was investigated. Optical Microscopy (OM), Scanning Electron Microscopy (SEM), and Energy Dispersive Spectrometer (EDS) were used to analyze the effect of tempering temperature on the microstructure and precipitation behavior of precipitates. The heat-resisting steel was heated to 1150 °C for 1 h, and then tempered at different temperatures between 680 °C and 760 °C for 2 h. The microstructure of the heat-resistant steel after tempering was composed of lath-tempered martensite and fine precipitates. The hardness decreased with increasing tempering temperature, ranging from HBW 261 to HBW 193. The aqueous corrosion resistance improved as the tempering temperatures increased from 680 °C to 720 °C but deteriorated at higher temperatures, such as 760 °C, which was obtained by an electrochemical corrosion performance test. The aqueous corrosion resistance was affected by the decrease in dislocation density and the decrease in Cr solution in the tempered martensite. With the increase in the tempering temperature, the aqueous corrosion potential first increases and then decreases, the self-corrosion current density first decreases and then increases, and the polarization resistance first increases and then decreases. Furthermore, the increase in corrosion resistance is attributed to the reduction in dislocation density and chromium depletion in the martensitic structure as the tempering temperature approaches 720 °C. This paper reveals the effect of tempering temperature on the corrosion resistance of 9Cr series heat-resistant steel, which is a further exploration of a known phenomenon.

Effects of temperature and drought stress on the seed germination of a peatland lily (Lilium concolor var. megalanthum)

Sexual reproduction through seeds is an effective way to renew plant populations and increase their genetic diversity, but seed germination process is complicated and relatively difficult due to the restriction of environmental conditions. Wetland plants that reproduce sexually through seeds may be affected by changes in moisture and temperature. This study aims to explore the ecological adaptation strategies of seed germination of Lilium concolor var. megalanthum under different hydrothermal conditions. Controlled experiments were conducted to investigate the germination performance of L. concolor var. megalanthum seeds at different temperatures (10°C, 15°C, 20°C, 25°C, and 30°C) and simulated drought stress conditions using PEG-6000 solutions (0%, 5%, 10%, 15%, and 20%). The results showed that temperature, drought stress, and their interaction significantly affected the days to first germination, germination percentage, coefficient of germination rate, germination energy, germination index, and vigor index of seeds (p<0.01). The germination percentage, germination index, and vigor index of seed were significantly higher at 25°C compared to other temperatures (p<0.01). The interaction between low temperature and drought stress significantly delayed the days to first germination. The inhibition of drought stress on seed germination was enhanced by PEG-6000 solution under high temperature. Under the conditions of 25°C and 5% PEG-6000 solution concentration, seeds of L. concolor var. megalanthum exhibited optimal germination parameters. At 10°C and 15°C, the seeds exhibited the highest tolerance to PEG-6000-simulated drought stress. Rehydration germination results showed that extreme temperatures and drought stress conditions inhibit seed germination of L. concolor var. megalanthum without damaging seed structure. The germination pattern of seeds under variable temperature and drought stress conditions reflects their adaptive strategies developed over long-term evolution to cope with the environmental conditions.

Effect of temperature and current density on PbO2 composite electrodes

Effect of temperature and current density on PbO2 composite electrodes

Theoretical Investigation into Polymorphic Transformation between β-HMX and δ-HMX by Finite Temperature String

Polymorphic transformation is important in chemical industries, in particular, in those involving explosive molecular crystals. However, due to simulating challenges in the rare event method and collective variables, understanding the transformation mechanism of molecular crystals with a complex structure at the molecular level is poor. In this work, with the constructed order parameters (OPs) and K-means clustering algorithm, the potential of mean force (PMF) along the minimum free-energy path connecting β-HMX and δ-HMX was calculated by the finite temperature string method in the collective variables (SMCV), the free-energy profile and nucleation kinetics were obtained by Markovian milestoning with Voronoi tessellations, and the temperature effect on nucleation was also clarified. The barriers of transformation were affected by the finite-size effects. The configuration with the lower potential barrier in the PMF corresponded to the critical nucleus. The time and free-energy barrier of the polymorphic transformation were reduced as the temperature increased, which was explained by the pre-exponential factor and nucleation rate. Thus, the polymorphic transformation of HMX could be controlled by the temperatures, as is consistent with previous experimental results. Finally, the HMX polymorph dependency of the impact sensitivity was discussed. This work provides an effective way to reveal the polymorphic transformation of the molecular crystal with a cyclic molecular structure, and further to prepare the desired explosive by controlling the transformation temperature.

Thermal transport in C6N7 monolayer: a machine learning based molecular dynamics study

The successful synthesis of a novel C6N7carbon nitride monolayer offers expansive prospects for applications in the fields of semiconductors, sensors, and gas separation technologies, in which the thermal transport properties of C6N7are crucial for optimizing the functionality and reliability of these applications. In this work, based on our developed machine learning potential (MLP), molecular dynamics (MD) simulations including homogeneous non-equilibrium, non-equilibrium, and their respective spectral decomposition methods are performed to investigate the effects of phonon transport, temperature, and length on the thermal conductivity of C6N7monolayer. Our results reveal that low-frequency and in-plane phonon modes dominate the thermal conductivity. Notably, thermal conductivity decreases with an increase in temperature due to temperature-induced increase in phonon-phonon scattering of in-plane phonon modes, while it increases with an extension in sample length. Our findings based on MD simulations with MLP contribute new insights into the lattice thermal conductivity of holey carbon nitride compounds, which is helpful for the development of next-generation electronic and photonic devices.

Heatwave events and concurrent ozone concentrations between 2006 and 2022 at two sites in southern and northern Spain.

Hotter-than-usual days are becoming more common, such that heat waves are expected to increase in intensity, frequency, duration, and spatial extent in Spain. Within this framework, this paper looks at the combined effects of extreme temperatures and air pollution in two cities in Spain, Córdoba and Valladolid, over the period 2006-2022. Synoptic patterns and air mass movement were analysed during the eleven coincident heat waves at both locations in order to study what impact orography and local meteorology have on ozone concentrations. Weak flow conditions were the most frequent synoptic pattern in the Iberian Peninsula during heat waves. Moreover, west and local circulations characterised the main air trajectories at low levels (500m agl), while southwest maritime advections and African air mass transport were more frequent at higher levels (1500 and 3000m agl) in Córdoba and Valladolid, respectively. On average, maximum ozone values were higher in Córdoba (105.1µgm-3) than in Valladolid (80µgm-3) and were strongly correlated with extreme temperatures at both locations (r up to 0.8, p-value < 0.05). Mean temperature in Córdoba was 31.9°C, with the maximum value reaching 43.7°C, while temperatures in Valladolid were lower (28.3°C and 37.3°C, respectively). Calculation and assessment of some indices helped to understand the impact of extreme events. Caution actions based on the Heat Index characterised heat wave periods. Moderate risk was the general Air Quality Health Index feature recorded and reached a very high risk of unhealthy air quality in the June 2022 event in Córdoba.

Effects of Pollen Germination and Pollen Tube Growth under Different Temperature Stresses in Mango (Mangifera indica L.) by Metabolome

Background: The dramatic temperature fluctuations spurred by global warming and the accompanying extreme weather events inhibit mango growth and threaten mango productivity. Particularly, mango flowering is highly sensitive to temperature changes. The mango fruit setting rate was significantly positively correlated with pollen activity, and pollen activity was regulated by different metabolites. Methods: In this study, the in vitro pollen of two mango varieties (‘Renong No.1’ and ‘Jinhuang’), in which sensitivity to temperature differed significantly, were subjected to different temperature stresses (15 °C, 25 °C and 35 °C), and their metabolomics were analyzed. Results: The present results showed that 775 differential metabolites were screened by liquid chromatography–mass spectrometry and divided into 12 categories. The two varieties had significant differences in metabolite expression under different temperature stresses and the effect of low temperature on ‘Renong No.1’ mainly focused on amino acid metabolism, while the effect on ‘Jinhuang’ was mainly related to glycolysis. However, under the 35 °C temperature stress, ‘Renong No.1’ responded by redistributing riboflavin and betaine in vivo and the most obvious metabolic pathway of ‘Jinhuang’ enrichment was pyrimidine metabolism, which had undergone complex main body formation and extensive regulatory processes. The changes of metabolites of different varieties under low temperature and high temperature stress were different. Among them, flavonoids or flavonoid derivatives were included in class A (216 metabolites), C (163 metabolites) and D (233 metabolites) metabolites, indicating that flavonoid metabolites had an obvious regulatory effect on mango pollen metabolism under different temperature stress. Conclusions: The present results provide valuable information for reproductive biology studies and breeding in mango, in particular, the selection and breeding of the most suitable varieties for different production areas.

Effect of pressure, temperature, and particle size on cold sintered ZnO for transparent thick films on polymer substrates

AbstractThe role of pressure, temperature, and particle size on cold sintering of ZnO has been investigated with a view to developing transparent thick films for device applications. Coarse ZnO (∼90–250 nm, cZnO) particles exhibited equiaxed grain growth under all conditions eventually achieving grain sizes of ∼ 0.5–1.0 µm at 300°C/375 MPa. In contrast, nano‐ZnO (40–80 nm, nZnO), exhibited grain growth along the c‐axis with a broader grain size distribution (0.5–4 µm) at higher temperatures and pressure (300°C/375 MPa) than cZnO. The broader grain size distribution is attributed to greater dissolution for nZnO compared with cZnO coupled with redistribution of Zn acetate/acetic acid into pores. ZnO continues to dissolve and reprecipitate within the pores throughout the densification process resulting in localized, larger grain sizes. In plane grain growth normal to the pressing direction was observed at and near the sample surface particularly in nZnO, which is attributed to constrained‐sintering. Some abnormal grain growth (10–20 µm) was also sporadically observed near or at the surface of nZnO (300°C/375 MPa) due to greater rates of reprecipitation as the transient solvent volatilizes adjacent to the die wall/plunger. Tape casting was used to fabricate single and multiple layers (≈30 µm) of ZnO on Kapton® to demonstrate the potential for device fabrication. Transparency was achieved by choosing cold sintering conditions (200°C/250 MPa) for nZnO that gave ∼95% relative density while restricting a majority of grain growth to &lt;200 nm so that internal light scattering from grain boundaries was avoided.

The Impact of Meteorological Factors on Stroke Incidence in the Transdanubian Region of Hungary

Cerebrovascular diseases are the leading cause of death and disability. The epidemiological background and predisposing factors have been the basis of many studies. We aimed to assess the effect of seasonal variability and meteorological factors on stroke incidence in Hungary. National and county-level secondary data were assessed for 2018–2019. We identified stroke with ICD codes I60, I61, I62 (hemorrhagic), I63, I65, and I66 (ischemic). The data were obtained from the University of Pécs Clinical Centre (number of patients per day according to sex and disease subtype, n = 1765). Daily average and maximum wind speed [m/s], precipitation [mm], temperature [°C], and frontal effect [warm/cold/mixed/no effect]) were provided by the Hungarian Meteorological Service. We found that 89.92% of the patients were hospitalized for ischemic and 10.08% for hemorrhagic stroke. We observed a significantly higher number of cases in the other months compared to winter (spring: +35.9%; p = 0.007, summer: +59.0%; p = 0.016, autumn: +36.5%; p = 0.01). In autumn, an increase in temperature increased the incidence of stroke (r = 0.210; p = 0.004). Temperature change affected ischemic stroke incidence (r = 0.112; p = 0.003). In contrast, the number of hemorrhagic stroke cases showed a mild but significant negative association with daily temperature change (r = −0.073; p = 0.049). Overall, a 1 °C temperature change compared to the previous day increased the daily number of admissions by 2.9% (p = 0.017). Air pressure change also affected hemorrhagic stroke incidence (r = 0.083; p = 0.025). Changes in temperature and frontal effects can increase the incidence of stroke. Modern forecasting technology can help the healthcare system prepare for possible increased workloads during critical periods.

Continuous wave laser ablation for tailored titanium nanoparticle synthesis: temperature and liquid medium effects

Continuous wave laser ablation for tailored titanium nanoparticle synthesis: temperature and liquid medium effects

Influence of temperature on the cathodic polarization behavior and calcareous deposit properties of X65 steel in sea water

Purpose This paper aims to investigate how cathodic polarization behavior significantly affects the selection of cathodic protection parameters and the effectiveness of protecting underwater metal structures. Factors such as water depth and operating conditions impact seawater temperature, making it crucial to understand the effects of temperature on cathodic protection parameters for underwater pipelines. Design/methodology/approach In this paper, potentiostatic polarization was carried out by three-electrode method, and morphology, X-ray diffraction and electrochemical analysis. Findings It was determined that the stable current densities at the minimum negative potential (−0.8 VSSC) for pipeline steel varied at different temperatures: 7°C, room temperature and 60°C. The cathodic protection potential corresponding to the lowest stable current density was observed to be −1.0 VSSC at 7°C and −0.95 VSSC at room temperature and 60°C. Originality/value This study elucidates the mechanisms by which different temperatures affect the protective performance of calcareous deposits and current densities.

The State of the Art on Phase Change Material-Modified Asphalt Pavement

During the construction and maintenance of asphalt pavement, a lot of non-renewable resources are consumed, which discharge a variety of waste gasses and smoke, causing a serious impact on the environment. Reducing society’s reliance on non-renewable resources is therefore key to improving sustainability. It is found that phase change materials (PCMs), as environmentally friendly materials, can spontaneously store and release heat energy by changing the phase state, thus reducing the adverse effect of temperature on asphalt pavement, reducing the occurrence of high-temperature stress, minimizing the cost of road construction and maintenance, and saving resources. In order to promote the application of PCMs in asphalt pavement, to promote self-controlling temperature technology for asphalt pavement, and to improve the sustainable development of asphalt pavement, this paper reviews the research status of PCMs in asphalt pavement, both domestically and abroad. The results show that the thermal conductivity of the modified asphalt binder can reach 0.29–0.39 W/mK, and the thermal diffusivity can reach 0.2–0.3 mm2/s, but the influence on the viscosity of the asphalt is limited, and both are less than 2000CP. The durability and thermal stability of the modified asphalt mixture are improved, and the maximum temperature can be lowered by 9 °C, which effectively reduces the occurrence of hightemperature stress. This review will help to better understand the function of PCMs and promote the sustainable development of green and environmentally friendly asphalt pavement.

Refined prediction of thermal transport performance in amorphous silica

Thermal transport in amorphous silica (a-SiO2) and silica aerogel is critically important for thermal protection and microelectronics applications. However, notable disparities exist between the predicted and measured thermal conductivity of a-SiO2. Inspired by the dual-phonon theory proposed by Luo et al. [Nat. Commun. 2020, 11, 2554] for crystalline materials, this work introduces a dual-diffuson transport method for amorphous materials. The criterion based on the thermal diffusivity is employed to differentiate between normal diffusons and phonon-like diffusons. Herein, the thermal conductivity of a-SiO2 is investigated by combining a modified Allen-Feldman (AF) theory with the dual-diffuson transport method. The present method is validated well by the measurement using the transient plane source (TPS) method. In addition, the results indicate that normal diffusons primarily govern the thermal transport in a-SiO2, with only a minor contribution from phonon-like diffusons. The temperature dependence of specific heat capacity and mode linewidth contributes to the positive temperature-dependent thermal conductivity. The quantum effect of specific heat capacity is the primary influencing factor in the temperature range of 100–1000 K, while the mode linewidth becomes dominant at higher temperatures. Finally, a theoretical framework for predicting the solid thermal conductivity of silica aerogel is introduced by including the temperature effect on the inherent thermophysical properties of the backbone. This work uncovers the physical mechanisms underlying temperature-dependent thermal transport in a-SiO2 and silica aerogels.

Effects of the internal temperature on vertical mixing and on cloud structures in ultra-hot Jupiters

The vertical mixing in hot-Jupiter atmospheres plays a critical role in the formation and spacial distribution of cloud particles in their atmospheres. This affects the observed spectra of a planet through cloud opacity, which can be influenced by the degree of cold trapping of refractory species in the deep atmosphere. We aim to isolate the effects of the internal temperature on the mixing efficiency in the atmospheres of ultra-hot Jupiters (UHJs) and the spacial distribution of cloud particles across the planet. We combined a simplified tracer-based cloud model, a picket fence radiative-transfer scheme, and a mixing length theory to the Exo-FMS general circulation model. We ran the model for five different internal temperatures at typical UHJ atmosphere system parameters. Our results show the convective eddy diffusion coefficient remains low throughout the vast majority of the atmosphere, with mixing dominated by advective flows. However, some regions can show convective mixing in the upper atmosphere for colder interior temperatures. The vertical extent of the clouds is reduced as the internal temperature is increased. Additionally, a global cloud layer gets formed below the radiative--convective boundary (RCB) in the cooler cases. Convection is generally strongly inhibited in UHJ atmospheres above the RCB due to their strong irradiation. Convective mixing plays a minor role compared to advective mixing in keeping cloud particles aloft in UHJs with warm interiors. Higher vertical turbulent heat fluxes and the advection of potential temperature inhibit convection in warmer interiors. Our results suggest that isolated upper atmosphere regions above cold interiors may exhibit strong convective mixing in isolated regions around Rossby gyres, allowing aerosols to be better retained in these areas.

Effect of temperature and extraframework cation type on CHA framework flexibility

The sorption properties of zeolites are controlled by several factors, i.e. Si/Al ratio of the aluminosilicate framework [AlSiO4]-, the type and position of the extraframework (EF) cations, and the applied temperature. Here we investigate the flexibility of CHA framework as a function of EF cation-content and temperature (20–350 °C). Two CHA forms (Na- and Cu-CHA) with Si/Al = 2 were analysed. The main objectives were: (i) to shed light on the HT behaviour of Na-CHA, for which contrasting results exist in literature; (ii) define the role of temperature and EF cation-type in the response to the heating stimuli. We show that at 75 °C, Na-CHA undergoes a severe contraction of the unit-cell volume (-12%) accompanied by a symmetry lowering (R-3m to I2/m). The transformation is reversible, if the dehydrated Na-CHA is exposed to ambient conditions. In contrast, Cu-CHA experiences a significant different dehydration path, which involves minor changes of the CHA framework, and a net positive thermal-expansion after dehydration. The implications of the observed transformations for gas separation processes are finally discussed.

Effect of Temperature and Duration of Storage on Seed Germination in Litchi (Litchi chinensis Sonn.)

Effect of Temperature and Duration of Storage on Seed Germination in Litchi (Litchi chinensis Sonn.)

Effect of Core Temperature at HPDC on the Internal Quality of the Casting

Effect of Core Temperature at HPDC on the Internal Quality of the Casting

Numerical simulation of condensation of supercritical water gasification products in a supersonic nozzle

The clean and efficient separation of supercritical water gasification products (SCWGP) has emerged as a significant challenge in supercritical water gasification technology. This paper proposes the use of a supersonic nozzle for the condensation and separation of H2 and CO2 from SCWGP, leveraging the high-pressure characteristics of these products. By establishing a flow model and a condensation model for the supersonic nozzle, the effects of inlet pressure and inlet temperature on the condensation process are analyzed. The analysis reveals that the latent heat released during condensation causes an abnormal distribution of pressure and temperature within the nozzle. When the inlet pressure of the nozzle is increased from 7.0 to 9.0 MPa, the liquid phase mass fraction at the outlet rises from 5.3 × 10−3 to 0.056. Similarly, when the inlet temperature is lowered from 300.0 to 290.0 K, the liquid phase mass fraction at the outlet also rises from 5.3 × 10−3 to 0.058. The increase in inlet pressure leads to the condensation location shifting toward the throat by ∼8.5 × 10−3 m⋅MPa−1, while the impact of inlet temperature is approximately −2.3 × 10−3 m⋅K−1. The nucleation rate in the nozzle is always concentrated in a small region.