Effect Of Lime Research Articles

Synergistic Effects of Red Clay and Lime for Improving Phyllite Soil

Phyllite soil and red clay belong to the soils that negatively impact the engineering performance of railway subgrade and may cause subgrade bulges, uneven subgrade settlement, and other subgrade distresses. In order to make full use of these two soils, a collaborative improvement plan was proposed. A series of tests were conducted to analyze the synergistic effects of lime and red clay on the improvement of phyllite soil. The tests included the no loading swelling ratio, swelling pressure, consolidation, and direct shear tests. Additionally, scanning electron microscopy was used to investigate the role of lime and red clay in soil improvement. The test results show that a red clay ratio of 60% + lime content of 3% is the optimal composite improvement scheme. The scheme led to a 93% reduction in the no loading swelling ratio and an 88% reduction in swelling pressure. Additionally, cohesion, the internal friction angle, and the compression modulus increased by 345%, 73%, and 373%. Red clay and lime had weak synergistic improvement effects on the no loading swelling ratio, the swelling pressure, and the internal friction angle of phyllite soil, that is, the synergistic improvement effect of red clay and lime was less than the sum of the single improvement effect but greater than the single improvement effect. Red clay and lime had a strong synergistic improvement effect on the cohesion and the compression modulus of phyllite, that is, the synergistic improvement effect of red clay and lime was greater than the sum of the single improvement effect. The microstructure analysis test results show that red clay can fill the pores of phyllite soil and improve its immediate strength. Through hardening and cementation, lime can enhance the strength of phyllite soil as well as address the issue of the reduced engineering properties of phyllite soil and red clay when exposed to water. Red clay and lime promote each other’s reactions and have a synergistic improvement effect on phyllite soil.

Effect of Electrochemical Interaction between Chalcopyrite and Hexagonal Pyrrhotite on Flotation Separation

The mechanism of electrochemical interaction between chalcopyrite and hexagonal pyrrhotite was analyzed via electrochemical interaction, copper ion concentration testing, and X-ray photoelectron spectroscopy (XPS) characterization. Besides, the effect of electrochemical interaction between the two minerals on the flotation separation was investigated using the mineral flotation tests, adsorption capacity tests, and a microcalorimetric test. Our research results showed that chalcopyrite had higher electrochemical activity than hexagonal pyrrhotite, and when the former acted as an anode during the electrochemical interaction of the two, the corrosion current density was three times higher than that when it acted alone, and the surface oxidation corrosion was intensified. At the same time, the interaction between the two minerals was accompanied by a large number of copper ions dissolved and adsorbed on the surface of the hexagonal pyrrhotite, so that adsorption of butyl xanthate intensified, adsorption increased, and flotation recovery increased by 5%–20%. However, owing to the increase in metal defects and the generation of hydrophilic sulfate, the surface of chalcopyrite hindered the adsorption of butyl xanthate on its surface, and the flotation recovery decreased by nearly 10% compared with that before the occurrence of the electrochemical interaction. This action also significantly weakened the inhibition effect of lime on hexagonal pyrrhotite and increased the difficulty of the flotation separation of the two minerals. The research results of this study provide theoretical guidance for the flotation separation of copper–sulfur ores containing pyrrhotite.

Effect of Micro Lime on The Ambient Cured Sugarcane Bagasse Ash-Based Geopolymer Concrete

Geopolymer concrete has been the ideal replacement for Ordinary Portland cement concrete in producing green concrete. The binder in geopolymer concrete is a cementitious paste made from amorphous Aluminosilicate and activated by an Alkaline solution. The geopolymerization process is initiated at elevated temperatures. Thus, the curing requires elevated temperatures. This curing method limits the application of geopolymer concrete in the construction industry. In a geopolymer mix, the presence of Calcium ions allows the formation of Calcium Aluminate Silicate and Calcium Silicate Hydrate gels, allowing ambient temperature curing. Therefore, this study investigates the effect of micro lime on the Sugarcane Bagasse Ash-based geopolymer concrete. The micro lime was added to the geopolymer concrete in 1, 3, 5 and 7% by the Sugarcane Bagasse Ash weight. A mix design was based on a Densified Mix Design Algorithm. The tests carried out included compressive strength and water absorption. Ambient curing of the SCBA-based geopolymer concrete was achieved with 1% of the micro lime. The compressive strength increased with the increase of the micro lime, 10N/mm2 at 1%, to 18.25N/mm2 at 7% micro lime. The ambient temperature-cured geopolymer concrete at 3% micro lime had the lowest water absorption rate.

PERUBAHAN KADAR TSS ( Total Suspended Solid) DAN PHOSPHATE AIR LIMBAH LAUNDRY DENGAN METODE KOAGULASI DAN FLOKULASI

Community life is growing along with increasing population and technological advancements. One of them is the use of laundry services that increases directly proportional to the waste produced. Laundry waste containing phosphate derived from Sodium Trypoliphosphate and high TSS (Total Disolved Solid) levels can cause eutrophication and turbidity in water bodies. The purpose of this study was to examine the effect of lime and alum addition in reducing phosphate and TSS (Total Suspended Solid) levels. The research method used is the experimental method, covering the principles of chemical and physical precipitation through the addition of 0.01 lime coagulant; 0.015; 0.02; 0.025 and 0.03 g and alum 0.1; 0.5; and 1.0 g. From the experiments, the best dose of lime and alum was obtained in reducing phosphate and TSS (Total Disolved Solid) levels in laundry wastes in lime weight 0.025 g and 1,000 g alum with a 99.80% removal percentage. Whereas for TSS (Total Disolved Solid) levels with a removal percentage of 90.89%. The processing of laundry waste using the ANOVA test showed an effect of the addition of variations in lime weight and alum to the decrease in phosphate and TSS levels in laundry waste. The results of the Tukey method showed that phosphate and TSS levels from each weight variation had different averages.

Investigation of the influence of lime content in the charge and its quality on the sintering process of iron ore raw materials

Main objectives of the work was to study the influence of degree of roasting of lime contained in the charge on the sintering process and sinter quality, as well as comparing the impact of changes in the mass fraction of active CaO in the charge by varying degrees of burning lime, and by varying the content of lime in the charge. It is shown that the intensifying effect of lime on the sintering process occurs as a result of a decrease in the content of small classes in the charge. When the lime content in the charge is equal to 3 %, an increase in the degree of lime firing from 5 to 96 % led to an increase in the specific productivity of the plant from 0.96 to 1.87 t/(m 2 · hour). The independence of sintering parameters from the content of active CaO in lime with its constant content in the sinter charge and the decisive role of the content of active CaO in the sinter charge with its constant content in lime are confirmed. A new approach to the production of lime for agglomeration processes is proposed: it should have the lowest cost of the active CaO contained in it.

Impact of Lime on Compaction Characteristics of Jamshoro Shale

The most complex problem for any civil engineering work is when the structure which is laying on the soil is weak. Jamshoro shale is an example of such problematic soil, which gets expanded as soon as it is exposed to moisture and shrinks back once it dries. Such phenomenon is very critical for the structures and road networks built on shale forming settlements and cracks. Such kinds of soil must be stabilized by chemical or mechanical techniques to make them strong enough to carry the loads and resist settlements and cracking. The stabilization of the ground by utilizing or adding any chemical agent is a sustainable approach; it strengthens the soil properties without replacing or wasting the soil present. In this research, the treatment of lime with shale is been performed to observe the modification of the geotechnical characteristics of the soil. The different proportions of Hydrated Lime 0%, 7%, 8%, and 9% were mixed by the dry weight of soil to investigate the effect of lime on the compaction and plasticity characteristics of the shale. Various tests such as the modified proctor test, liquid limit test, and plastic limit test performed in the laboratory. From the results, it was observed that the properties of Jamshoro shale such as plasticity index, optimum moisture content, and maximum dry density were improved. The plasticity index of shale dropped to 2% from 24%. That suggests lime can be used as an economical and eco-friendly stabilizing agent.

Biochar derived from invasive plants improved the pH, macronutrient availability and biological properties better than liming for acid rain-affected soil

Rapid development in industrialization and urbanization causes serious environmental issues, of which acid rain is one of the quintessential hazards, negatively affecting soil ecology. Liming has been investigated for a long time as the most effective amendment to alter the adverse effects of soil acidity resulting from acid rain. Herein, this study tested the biochar produced from invasive plants as an alternative amendment and hypothesized that biochar can maintain better availability of macronutrients under acid rain than liming by improving soil chemical and biological properties. Therefore, a pot experiment was conducted to compare the effects of lime and biochar at two rates (1% and 3%) on soil available nitrogen (N), phosphorous (P) and potassium (K) under simulated acid rain of two pH levels (4.5: pH4.5 and 2.5: pH2.5) as compared with tap water (pH7.1) as a control treatment. Biochar was produced using different invasive plants, including Blackjack (Biden Pilosa), Wedelia (Wedelia trilobata) and Bitter Vine (Mikania micrantha Kunth). Liming decreased the availability of soil N, P, and K by 36.3% as compared with the control due to the great increment in soil pH and exchangeable calcium (Ca2+) by 59% and 16-fold, respectively. Moreover, liming reduced the alpha diversity of soil bacteria and fungi by 27% and 11%, respectively. In contrast, biochar at different types and rates resulted in a fourfold increment in the available N, P, and K as an average under acid rain (pH4.5 and pH2.5) owing to maintaining a neutral pH (6.5–7), which is the most favorable level for soil microbial and enzymatic activites, and the bioavailability of soil nutrients. Furthermore, biochar caused balanced increments in Ca2+ by threefold, cation exchange capacity by 45%, urease activity by 16%, and fungal diversity by 10%, while having a slight reduction in bacterial diversity by 2.5%. Based on the path, correlation, and principal component analyses, the exchangeable aluminum was a moderator for the reductions in macronutrients’ availability under acid rain, which decreased by 40% and 35% under liming and biochar, respectively. This study strongly recommended the use of biochar from invasive plants instead of lime for sustainable improvements in soil properties under acid rain.Graphical

Properties of Poultry-Manure-Derived Biochar for Peat Substitution in Growing Media.

Peat is considered a contentious input in horticulture. Therefore, there is a search for suitable alternatives with similar properties that can be used for partial or complete peat substitution in growing media. Poultry-manure-derived biochar (PMB) is considered such an alternative. This study aimed at determining the properties of PMBs obtained through pyrolysis at selected temperatures and assessing their potentials to substitute peat in growing media based on the selected properties. The scope included the laboratory-scale pyrolysis of poultry manure at the temperatures of 425-725 °C; the determination of selected physico-chemical and physical properties of the obtained biochars, including the contaminants; and the assessment of the potentials of produced biochars to be used as peat substitutes. PMBs contained less than 36% of total organic carbon (TOC). The contents of P and K were about 2.03-3.91% and 2.74-5.13%, respectively. PMBs did not retain N. They can be safely used as the concentrations of heavy metals, polycyclic aromatic hydrocarbons (PAHs), polychlorinatd biphenyls (PCBs), dioxins, and furans are within the permissible values (except for Cr). Due to high pH (9.24-12.35), they can have a liming effect. High water holding capacity (WHC) in the range of 158-232% w/w could allow for the maintenance of moisture in the growing media. PMBs obtained at 525 °C, 625 °C, and 725 °C showed required stability (H/Corg < 0.7).

Mechanical Properties and Dry–Wet Stability of Soda Residue Soil

To effectively utilize the effectively the solid waste-soda residue (SR) and fly ash (FA), a mixture of 70% SR, 20% FA, and 10% clay was formed to produce soda residue soil (SRS). By adding cement and/or lime, four different SRS proportions were prepared. The compaction properties, mechanical properties, and dry–wet stability. Furthermore, the mechanical mechanisms of SRS were explored, and the improvement effect and efficiency of cement and/or lime on the mechanical performance of SRS were analyzed. The results show that the SRS is lightweight and easy to compact and shape, which is conducive to construction. Compared to cement, lime has a greater impat on the compaction properties of SRS. The mechanical properties of SRS are enhanced after adding cement and/or lime; the unconfined compressive strength (UCS), California Bearing Ratio (CBR), and resilient modulus all increase significantly. The UCS, CBR, and resilient modulus of SRS with different proportions all increase with the increase of compaction degree; the CBR and resilient modulus can meet the requirements of the subgrade, and the UCS can meet the requirements of the base and sub-base. The contribution rate of cement per unit amount is better than that of lime to the mechanical performance of SRS. As dry–wet cycles increase, the dry–wet stability of SRS with different proportions first increases and then decreases, which is affected by hydration and dry–wet deterioration together, with a critical cycle number for the strength transition. The excellent mechanical performance of SRS benefits from the gradation and chemical action. The particles of SR, FA, and clay can complement each other and perform an interlocking action. Therefore, SRS has a good gradation and forms a dense and stable structure. Also, the chemical reactions between materials are very important. The cement and/or lime have a hydration and gelling effect, FA and clay participate in pozzolanic reactions, and SR and FA have certain alkali-activated effects.

Biochar-Acid Soil Interactions—A Review

Soil acidity is a major problem of agriculture in many parts of the world. Soil acidity causes multiple problems such as nutrient deficiency, elemental toxicity and adverse effects on biological characteristics of soil, resulting in decreased crop yields and productivity. Although a number of conventional strategies including liming and use of organic and inorganic fertilizers are suggested for managing soil acidity but cost-effective and sustainable amendments are not available to address this problem. Currently, there is increasing interest in using biochar, a form of biomass derived pyrogenic carbon, for managing acidity while improving soil health and fertility. However, biochar varies in properties due to the use of wide diversity of biomass, variable production conditions and, therefore, its application to different soils can result in positive, neutral and or negative effects requiring an in-depth understanding of biochar-acid soil interactions to achieve the best possible outcomes. Here, we present a comprehensive synthesis of the current literature on soil acidity management using biochar. Synthesis of literature showed that biochars, enriched with minerals (i.e., usually produced at higher temperatures), are the most effective at increasing soil pH, basic cation retention and promoting plant growth and yield. Moreover, the mechanism of soil acidity amelioration with biochar amendments varies biochar types, i.e., high temperature biochars with liming effects and low temperature biochars with proton consumption on their functional groups. We also provide the mechanistic interactions between biochar, plant and soils. Altogether, this comprehensive review will provide guidelines to agricultural practitioners on the selection of suitable biochar for the reclamation of soil acidity.

Impact Of Poultry Manure And Agricultural Lime On Acidic Soil Of Fiji

The objective of this study is to prove whether Poultry Manure (PM) is a suitable organic alternative to Lime Stone (LS) to neutralize acidic soil in Fiji. A greenhouse experiment was conducted to compare the effects of poultry manure and agricultural Lime on soil fertility on selected chemical properties of an acidic soil series of Fiji. The pots received seven treatments, an unamended control, 5.0, 7.5 and 1.0Mg/ha-1 PM and lime. All treatments were replicated three times and were arranged in the greenhouse in the randomized design. The pots received 200 mL water continually for four weeks. The results indicated that the application of PM increased the soil pH, %N, exchangeable Ca, Mg, K and P levels amended soil compared to CaCO3. The study clearly demonstrate that the fertility of acidic soil can be corrected by either (CaCO3) or PM addition. It is evident that PM maybe used as an alternative to CaCO3. The conventional liming materials such as calcium carbonate are not only scarce and expensive. There is needed to focus on development of locally adapted indigenous and sustainable way of managing soil acidity.

Lime and gypsum application to low-acidity soils: Changes in soil chemical properties, residual lime content and crop agronomic performance

Crop yield gains and improvements in surface and subsurface soil chemical properties are evident when agricultural lime and gypsum are used in high-acidity soils. However, there is scarce information on the effects of lime and gypsum application on no-till tropical soils previously treated with these additives (low-acidity soils). The duration of the effects of lime applied to the soil surface varies according to lime rate, product characteristics, soil conditions, and water and thermal regimes. Such residual effects influence the timing of lime reapplication. This study aimed to investigate the effects of surface application of agricultural lime and gypsum on soil chemical properties, soybean and second-crop corn yields, and lime residual contents. The experiment was conducted on a Red Latosol with a very clayey texture in Floresta, Paraná, Brazil. Four rates of dolomitic lime (0.0, 2.6, 5.4, and 8.1 Mg ha−1) and agricultural gypsum (0, 4, 8, and 12 Mg ha−1) were used. The experimental design was a randomized complete block with subplots and four replications. The experiment lasted for four soybean seasons and three second-crop corn seasons. At 6, 12, 24, and 36 months after treatment, soil samples were collected from the 0.00–0.05, 0.05–0.10, 0.10–0.20, 0.20–0.30, 0.30–0.40, and 0.40–0.60 m layers for chemical analysis. No significant interaction effects were observed on soil chemical properties. Liming resulted in soil alkalization, with a consequent reduction in Al3+ and an increase in Ca, Mg, base saturation, and pH. Residual lime was not detected in layers deeper than 0.05 m, suggesting a lack of physical movement of particles in the soil pore space. Residual lime was detected on surface soil (0.00–0.05 m) up to 36 months after application, demonstrating the low reactivity of lime on no-till soils. At 6 months after gypsum application, there was an increase in Ca2+ levels up to the 0.6 m layer, whereas Mg2+ levels were reduced throughout the soil profile for up to 36 months. In no-till soybean–second-crop corn rotation systems, use of agricultural gypsum alone did not provide consistent effects on crop yield and reduced foliar Mg contents. Under the studied conditions of low acidity, liming did not produce significant differences in crop yield but improved soil chemical properties for plant growth under no-till.

The Effect of Different Lime Forms on Cadmium Uptake of Durum Wheat Varieties

Cadmium (Cd) accumulation in durum wheat (Triticum durum L.) and its human transport with food chain is a major environmental issue worldwide. The research was based on a pot experiment conducted on fifteen durum wheat cultivars, grown on acid soil pH 5.2. The effect of application of two different lime form (lime1=CaO; Calcium oxide and lime2=CaCO3; limestone) and on shoot dry weight and shoot concentrations of cadmium (Cd). Durum wheat cultivars were grown in strongly acid soil pH 5.2 treated with control (lime0), lime1 (CaO3 g kg-1 soil), lime2 (5.36 g CaCO3) and Cd (5 and 10 mg kg-1 soil) and harvested after 62 days of growth under greenhouse conditions. Durum wheat cultivars without lime fertilization caused decrease in shoot growth, in all durum wheat cultivars and at high Cd treatment. On the other hand, application of lime to the soil resulted in an increase in dry matter yield at both Cd5 and Cd10 doses. While average shoot dry matter yield of lime0 conditions of cadmium 10 dose was 47 mg plant-1, this yield increased to 120 mg plant-1 in lime1 application and to 111 mg plant-1 in lime2 application. Shoot Cd concentrations of durum wheat varieties caused a statistically significant decrease with lime1 and lime2 applications, whereas lime0 and lime2 applications of Cd5 dose caused 46% and 30% decrease in average Cd concentrations, respectively. The results indicated that all durum wheat cultivars were more susceptible to both without lime and Cd toxicity as compared to lime treatment. Cadmium toxicity in the shoot was relieved by lime1 and lime2 treatment. The results indicate that lime protects plants from Cd toxicity in durum wheat cultivars.

Comparative Study on the Impact of Sand and Lime on the Physical and Mechanical Characteristics of Unfired and Fired Earth Bricks

Earth bricks represent one of the most important and widely used building materials in current era, due to its unique physical and mechanical properties compared to other materials. Earth bricks are available in two main types: raw earth bricks and fired bricks. The physical and mechanical properties differ for each type, which affects their performance in various applications and their long-term durability. Several studies have been conducted to improve the properties of raw and fired bricks and address their weaknesses. In this research, we aim to investigate the effects of adding dune sand and lime on the physical and mechanical properties of raw earth and fired bricks, and compare the results. Sand was added by 25%, while lime was added by 0, 6, 8, 10, and 12% of the soil matrix weight. Initially, we determined the properties of the raw materials used. After creating the samples, they underwent tests for bulk density, longitudinal shrinkage, compressive strength, and flexural strength. The study revealed the positive impact of adding sand on the physical and mechanical properties of raw and fired bricks. It contributed to reducing the bulk density and longitudinal shrinkage of the samples, while increasing their compressive and flexural strength to varying extents. The results also showed the positive effect of lime on the physical and mechanical properties of raw bricks, as long as it was added at a ratio not exceeding 10%. However, the addition of lime to fired bricks affected the physical properties positively but it has a negative effect on the mechanical properties.

Physiological response of new citrus rootstocks under the effect of lime induced iron chlorosis stress conditions

ABSTRACT Citrus orchards are highly affected by iron chlorosis in Mediterranean Basin, which is the second-highest producing region worldwide. In addition, citrus orchards from the Mediterranean Basin are exposed to emerging diseases, such as Huanglongbing, the most devastating citrus disease worldwide. Consequently, citrus rootstock can serve as an interesting tool to reduce crop losses caused by these abiotic and biotic stresses. In our study, we evaluated the effect of four Fe-chlorosis stress treatments on six new citrus rootstocks under greenhouse conditions and compared with Carrizo citrange and Forner-Alcaide 5. Above-ground symptoms and chlorophyll index (SPAD) were recorded on a regular basis during the experiment. At the end of the assay, root, stem, and leaves biomass and Fe concentration in leaves were recorded. Plant symptoms were detected under Fe-chlorosis stress treatments, in which 2247 × 6070-02-2 and UFR-6 displayed lower incidence than other citrus rootstocks. These plant symptoms were in keeping with the SPAD response per citrus rootstock. Almost all citrus rootstock reported the highest biomass reduction under the treatment of 1 g CaCO3/l pH 9. Only two citrus rootstocks (Carrizo citrange and B11R5T49) achieved the highest Fe concentration on leaves under control conditions compared with the other treatments per citrus rootstock. Abbreviations: F: iron; FC-R: Ferric Chelate Reductase; HLB: Huanglongbing or citrus greening; Without Fe: nutritive solution without iron; SAUASPC: standardised area under the abiotic stress progress curve; D1: day 1; D10: day 10; D21: day 21; D32: day 32; D42: day 42; D52: day 52; D64: day 64; D84: day 84; FW: fresh weight per section plant; DW: dry weight per section plant; FWT: total fresh weight; DWT: total dry weight; PBR: percentage of biomass reduction; CW: weight (g) of control treatment plants averaged eight replicates; TW: weight (g) of treated plants at each concentration of Fe tested; ICP-OES: inductively coupled plasma optical emission spectroscopy

Ligneous amendments increase soil organic carbon content in fine-textured boreal soils and modulate N2O emissions.

Organic soil amendments are used to improve soil quality and mitigate climate change. However, their effects on soil structure, nutrient and water retention as well as greenhouse gas (GHG) emissions are still poorly understood. The purpose of this study was to determine the residual effects of a single field application of four ligneous soil amendments on soil structure and GHG emissions. We conducted a laboratory incubation experiment using soil samples collected from an ongoing soil-amendment field experiment at Qvidja Farm in south-west Finland, two years after a single application of four ligneous biomasses. Specifically, two biochars (willow and spruce) produced via slow pyrolysis, and two mixed pulp sludges from paper industry side-streams were applied at a rate of 9-22 Mg ha-1 mixed in the top 0.1 m soil layer. An unamended fertilized soil was used as a control. The laboratory incubation lasted for 33 days, during which the samples were kept at room temperature (21°C) and at 20%, 40%, 70% or 100% water holding capacity. Carbon dioxide (CO2), nitrous oxide (N2O) and methane (CH4) fluxes were measured periodically after 1, 5, 12, 20 and 33 days of incubation. The application of ligneous soil amendments increased the pH of the sampled soils by 0.4-0.8 units, whereas the effects on soil organic carbon content and soil structure varied between treatments. The GHG exchange was dominated by CO2 emissions, which were mainly unaffected by the soil amendment treatments. The contribution of soil CH4 exchange was negligible (nearly no emissions) compared to soil CO2 and N2O emissions. The soil N2O emissions exhibited a positive exponential relationship with soil moisture. Overall, the soil amendments reduced N2O emissions on average by 13%, 64%, 28%, and 37%, at the four soil moisture levels, respectively. Furthermore, the variation in N2O emissions between the amendments correlated positively with their liming effect. More specifically, the potential for the pulp sludge treatments to modulate N2O emissions was evident only in response to high water contents. This tendency to modulate N2O emissions was attributed to their capacity to increase soil pH and influence soil processes by persisting in the soil long after their application.

Effect of Boron and Lime on Boron Transformation in a Fluvaquentic Humaquepts Soil Concerning Uptake and Yield of Green Gram

Understanding different fractions and availability of boron (B) is essential while studying the response of crops towards B. Fractionation provides information about the chemistry of B and quantifies its bioavailability. Therefore, a pot experiment was performed during the 2019 pre-kharif season in acid soil to study soil B fractions and response of green gram (Vigna radiata L.) to B application. Lime is applied to such soils with the primary objective of increasing the productivity of crops by enhancing the availability of native and applied plant nutrients. On the contrary, availability of B in soil was increase due to liming. The treatments comprised of five levels of soil applied B (0, 0.5, 1.0, 1.5 and 2.0 mg B kg−1) and two levels of lime, lime and no lime was used. The experiment was laid out in factorial randomized block design (FRBD) with three replications. The soil and pant growth parameters were recorded at a regular interval of 15 days after sowing, and at harvest. All the result revealed that the changes in different fractions of B (viz., readily soluble, specifically adsorbed, oxide bound, organically bound, residual and total B), its plant uptake and yield of green gram are significantly affected by the application of B and lime. All the fractions contribute towards plant available boron form. Inter conversion between B fractions was also observed. The application of B and lime significantly influenced different B pools, boron uptake and yield of green gram.

Liming and spring salamander abundance

AbstractEnvironmental acidification is affecting ecosystems around the globe, and as a result, managers are using limestone applications to mitigate the effects of acid rain and acid mine drainage. Limestone applications attempt to reverse acidification by increasing stream pH; however, liming can have variable effects on stream biota. We examined the effects of liming on spring salamander (Gyrinophilus porphyriticus) abundance in West Virginia, USA, from 10 June to 1 September 2013. We used multiple methods (i.e., leaf litterbags, visual encounter surveys, area constrained flip and search) to sample spring salamanders within 11 different streams in the Monongahela National Forest. Using N‐mixture models, which allow for estimation of abundance from count data and account for imperfect detection probabilities, we examined the effects of direct application liming (DAL) on spring salamander abundance. Direct application liming at a higher lime frequency did not have a significant effect on salamander abundance; however, we observed differences in spring salamander size in areas near the DAL site. These results have influenced management of limed streams and will enlighten managers to the effects of high frequency liming on salamander communities and other stream organisms, and will provide insights on how to mitigate potential impacts as a result of liming practices.

Pengaruh Ukuran Butir Kapur Berbeda terhadap pH, Fe-larut dan Al-tukar Tanah pada Lahan Pasang Surut

Swampland in Indonesia covers an area of ​​34.93 million ha spread over various islands such as Sumatra, Java, Kalimantan, Sulawesi, and Papua. One type of swamp land that is often used in agriculture is tidal lands. The problems faced in the development of tidal lands for agriculture include acidic soil pH, high levels of soluble Fe and Al. One of the efforts to overcome the problem of acidic soil pH, high levels of soluble Fe and Al-dd is liming. The finer grain level of lime may increase the effectiveness of liming. The purpose of this study was to quantify the effect of lime grain sizes on changes in pH, dissolved Fe, and exchangeable Al of tidal lands. This study employed a one-factor completely randomized design (CRD) consisting of 6 treatments (Control; CaCO3 more than 1.00 mm (&gt; 18 mesh); CaCO3 lime, 0.5-100 mm (18 -35mesh); CaCO3 measuring 0.21-0.50 mm (35-70 mesh); CaCO3 measuring 0.21 mm (&lt;70 mesh); CaCO3 lime measuring 0.15-1.00 mm (18 -100 mesh)). The results showed that the difference in the size of the CaCO3 lime granules had a significant effect on changes in pH, soluble Fe and exchangeable Al. The application of CaCO3 lime granules 0.21 mm (&lt;70 mesh) result in increases in soil pH and suppress soluble Fe and exchangeable Al.

Soil potassium regulation by initial K level and acidification degree when subjected to liming: A meta-analysis and long-term field experiment

Potassium (K) is the most commonly neglected macronutrient in global change, especially in acidified areas. Lime is a typical management to eliminate soil acidification in agroecosystem soils; however, its impact on soil K dynamics remains inconsistent under different acidic environments. Here, we combine a meta-analysis based on 407 observations from 89 papers and a long-term experiment to investigate the effect and main driving factors of liming on soil K change. The meta-analysis showed that lime application significantly reduced topsoil exchangeable K (EK) content by an average of 4.8% globally. The decrease in topsoil EK content due to liming depended on various soil properties, crop types, fertilizer regimes, and experiment types. Boosted regression tree analysis showed that initial soil exchangeable K (IEK) and pH were the main factors affecting soil EK change under the lime application. The field experiment results further evidence that the decrease of soil EK after the lime application was mainly due to increased K uptake by the crop, and EK transformed to non-exchangeable K (NEK). The application of lime has a greater impact on reducing subsoil EK content at a higher IEK thresholds. Soil EK showed a significant negative relationship with exchangeable calcium (Ca) and a significant positive relationship with exchangeable aluminum (Al). Redundancy analysis revealed that K input (KI), IEK, lime, Ca, Al, pH, and exchangeable magnesium significantly affected the K in soil and crops. The partial least squares path model showed that lime application and IEK levels combined indirectly influence soil K (EK and NEK) by directly affecting soil Ca and Al, K uptake, and K balances. The findings highlight the importance of the lime effect on K management in globally adverse environmental agroecosystems and indicate the key role of initial soil EK levels and acidification degree for regulating crops to excavate the subsoil potassium when subjected to liming.