Effect Of Addition Research Articles

Effects of Vitamin C on the Gonad Growth, Texture Traits, Collagen Content and Synthesis Related Gene Expression of Sea Urchin (Mesocentrotus nudus)

The market value of sea urchin gonads is determined by the specific characteristics associated with gonad size and texture. Formulated feeds can effectively promote the gonad growth of sea urchins but cannot assure essential gonad texture traits. The objective of this study was to investigate the impact of vitamin C (VC) on the gonad growth, texture, collagen content, and the expression of genes involved in the collagen synthesis of sea urchins (Mesocentrotus nudus). Graded amounts of VC (0, 3000 and 6000 mg/kg) were supplemented to make three formulated feeds. Fresh kelp (Saccharina japonica) was used as the control diet. Each diet was randomly distributed to three tanks of M. nudus. The results indicated that the gonadosomatic index (GSI) and texture traits of M. nudus fed C3000 were significantly greater than those fed C0 and C6000. Collagen type I (Col I) in the gonads of M. nudus fed C3000 showed significantly greater areas than those fed C0 and C6000. Consistently, the expression levels of collagen alpha-1 (colp1α) of M. nudus fed C3000 were significantly higher than those fed C0 and C6000. As for the transforming growth factor beta (tgf-β)/Smads pathway, the expression levels of collagen synthesis genes (tgf-β receptor 1 and 2, smad nuclear-interacting protein 1 (snip1) and prolyl 4-hydroxylase subunit beta (p4hβ)) in the C3000 group were significantly greater than those in the C0, C6000 and kelp groups. On the contrary, the expression levels of collagen degradation genes (lysyl oxidase-like 2 (loxl2) and matrix metalloproteinase 14 (mmp14)) in the C3000 group were significantly lower than those in the C0, C6000 and kelp groups. In conclusion, VC at an addition level of 3000 mg/kg significantly increased the gonad texture and collagen contents of M. nudus, which could be accomplished by increasing collagen synthesis and inhibiting collagen degradation through the tgf-β/Smads pathway. These results could contribute to better understanding the beneficial effects of VC addition on the gonad texture quality of M. nudus.

Effect of Cumulative Amendment of Soil with Fly Ash in Combination with Other Nutrients on Change in Grain Yield, Crude Protein, NPN and True Protein Contents of Rice

An experiment was planned and conducted at Instructional Farm (IF), Odisha University of Agriculture & Technology (OUAT), Bhubaneswar in the years 2022 and 2023 during the Kharif seasons to study the effect of the cumulative addition of nine varieties of nutrients on the yield and protein contents of two varieties of rice namely Gayatri and Vandana. The applied fly ash (FA) was alkaline in nature whereas the soil was acidic. The grain yield of the Kharif crop in 2022 (Gayatri) varied from the lowest of 31.56 qha-1 to the highest of 37.21 qha-1. It varied from the lowest of 38.66 qha-1 to the highest of 43.82 qha-1 in 2023. The crude protein content varied from the lowest of 7.97% to the highest of 9.16% in 2022 but it varied from the lowest of 7.31% to the highest of 8.39% in 2023. The non-protein nitrogen (NPN) content varied from the lowest of 7.97% to the highest of 9.16% in 2022 but it varied from the lowest of 7.31% to the highest of 8.39% in 2023. The true protein content varied from the lowest of 6.90% to the highest of 7.97% in 2022 but it varied from the lowest of 6.12% to the highest of 7.50% in 2023. It was observed that the grain yield, crude protein, non-protein nitrogen (NPN) and true protein content decreased by the application of FA over control (only NPK fertilizer). The crude protein content decreased in all the treatments in 2023 over its 2022 counterpart whereas NPN increased by the cumulative addition of nutrients. This resulted in higher values of true protein content in the grains in the year 2023. Grain yield increased in all the treatments in 2023 over the previous year resulting in higher yield of true protein content. Hence more amount of protein rich grains per hectare can be obtained by the cumulative addition of nutrients in spite of varietal difference of the grains.

Effects of Dye Addition on the Rheological Properties of Aqueous Polymer Solutions.

In many commercial applications, polymer-dye interactions are frequently encountered from food to wastewater treatment, and while shear rheology has been well characterized, the extensional properties are not well known. The extensional viscosity ηE and relaxation time λE are the extensional rheological parameters that provide valuable insights into how aqueous polymers respond during deformation, and this study investigated the effect of dyes on the extensional rheology of three different aqueous polymer solutions (e.g., anionic, cationic, and neutral) paired with two different dye salts (e.g., anionic and cationic) using drop pinch-off experiments. We have found that the influence of dyes on the pinch-off dynamics is complex but generally leads to a decrease in, for example, the apparent extensional relaxation time. We have utilized the dripping-onto-substrate method to probe the uniaxial deformation of widely used polymers such as xanthan gum (XG), poly(diallyldimethylammonium chloride) (PDADMAC), and poly(ethylene oxide) (PEO) as the anionic, cationic, and neutral polymers, respectively, paired with either fluorescein (Fl) or methylene blue (MB) as the anionic and cationic dyes, respectively. Polymer-dye pairs with opposite charges (e.g., XG-MB and PDADMAC-Fl) displayed a pronounced decrease in pinch-off times, but even PEO, which is a neutral polymer, resulted in decreased pinch-off times, which was restored by the addition of NaCl. The pinch-off times for the Boger fluid (mixture of poly(ethylene glycol) and PEO), however, were surprisingly uninfluenced by dyes. These results showed that not only did the small addition of dyes strongly decrease the polymer relaxation times, but the relative importance of the dye salts on the polymer pinch-off dynamics was also different from that of pure salts such as NaCl.

Change in functional trait diversity mediates the effects of nutrient addition on grassland stability

Abstract Nutrient enrichment impacts grassland plant diversity such as species richness, functional trait composition and diversity, but whether and how these changes affect ecosystem stability in the face of increasing climate extremes remains largely unknown. We quantified the direct and diversity‐mediated effects of nutrient addition (by nitrogen, phosphorus, and potassium) on the stability of above‐ground biomass production in 10 long‐term grassland experimental sites. We measured five facets of stability as the temporal invariability, resistance during and recovery after extreme dry and wet growing seasons. Leaf traits (leaf carbon, nitrogen, phosphorus, potassium, and specific leaf area) were measured under ambient and nutrient addition conditions in the field and were used to construct the leaf economic spectrum (LES). We calculated functional trait composition and diversity of LES and of single leaf traits. We quantified the contribution of intraspecific trait shifts and species replacement to change in functional trait composition as responses to nutrient addition and its implications for ecosystem stability. Nutrient addition decreased functional trait diversity and drove grassland communities to the faster end of the LES primarily through intraspecific trait shifts, suggesting that intraspecific trait shifts should be included for accurately predicting ecosystem stability. Moreover, the change in functional trait diversity of the LES in turn influenced different facets of stability. That said, these diversity‐mediated effects were overall weak and/or overwhelmed by the direct effects of nutrient addition on stability. As a result, nutrient addition did not strongly impact any of the stability facets. These results were generally consistent using individual leaf traits but the dominant pathways differed. Importantly, major influencing pathways differed using average trait values extracted from global trait databases (e.g. TRY). Synthesis. Investigating changes in multiple facets of plant diversity and their impacts on multidimensional stability under global changes such as nutrient enrichment can improve our understanding of the processes and mechanisms maintaining ecosystem stability.

Research of the influence of adhesive additives on the bond strength between layers of polyvinyl chloride awning materials

To create polyvinyl chloride (PVC) tent materials with high adhesive strength between layers, formulations of plastisols using adhesive additives – ED-20 epoxy resin and polyethylene polyamine (PEPA) crosslinking agent, diisocyanate and perchlorovinyl resin – have been developed. Rheological properties of plastisols containing adhesion additives of different nature have been studied. The effect of adhesion additives on the bond strength between polyester fabric and PVC coating have been investigated.

Evaluation of impacts of biosolids application and drainage water management on soil N2O and CH4 emissions using the flux gradient method

Existing studies have shown contradictory findings with respect to whether biosolids applications on agricultural lands lead to intensification of soil greenhouse gas (GHG) emissions. Here, we describe the results of deployment of the micrometeorological flux gradient method to quantify post-biosolid soil emissions of nitrous oxide (N2O) and methane (CH4) on a farm with drainage water management (DWM) on the Eastern Shore of Maryland. The fluxes following biosolid additions to cornfields in 2020 were compared with fluxes from the same farm in 2018, when no fertilizer was applied to soybeans, and in 2019, when urea ammonium nitrate (UAN) was applied to corn. Extractable soil nitrate was highest following biosolids application, contributing to the highest N2O emissions in the growing season of 2020 compared to 2018 (no fertilizer) and 2019 (UAN). Other contributing factors include the low C:N ratio of the biosolids and the above average precipitation in 2020. In contrast, different fertilization regimes did not generate distinct differences for CH4 fluxes, which were very low in all three years. No statistically significant treatment effect of DWM was found for either N2O or CH4 during the peak emission period after biosolids application, which aligns with the result of our earlier research. Annualized estimated N2O emission factors (EFs) for biosolids addition were 5–6 % in the DWM and 3–4 % in the non-DWM fields, although this includes uncertainties associated with gap filling. These biosolids EFs are 2–3 times the N2O EF for synthetic fertilizer application at this same farm in 2019 (1–2.5 %) and 2–4 times the IPCC Tier 1 EF (1.6 %) for synthetic fertilizer, demonstrating the intensification effect of biosolids addition on soil N2O emissions for the cropland studied here.

Effects of Fe addition on the mechanical and corrosive properties of biomedical Co-Cr-W-Ni alloys for balloon-expandable stents

Co-20Cr-15W-10Ni (mass%, CCWN) alloy is extensively used as a platform material for balloon-expandable stents. In this study, the mechanical properties of CCWN alloy are improved following the addition of Fe, and the effects of Fe addition on the mechanical and corrosive properties of the alloy are investigated. As-cast specimens were fabricated by adding pure Fe to a commercially available CCWN alloy (base alloy) such that the resulting alloys contained 4, 6, and 8 mass% Fe. The as-cast specimens were subjected to homogenization heat treatment at 1523 K for 7.2 ks and then hot-forged at 1473 K (as-forged specimens). The as-forged specimens were cold-rolled at a reduction rate of 30% and heat-treated at 1473 K for 300 s (recrystallized specimens). The matrix of the recrystallized base- and Fe-containing alloys consisted of a single γ (face-centered cubic)-phase. The Fe-added alloys revealed precipitates composed of the η-phase (M6X-M12X-type phase, M: metallic element, X: C and/or N). The average grain size of the recrystallized base and Fe-added alloy specimens was approximately 34 μm and the amount of added Fe had no significant effect on the static recrystallization behavior of the resulting alloys. Alloys containing 6 mass% or more Fe showed improvements in strength and ductility compared with the base alloy. When the Fe-added alloys were compared, their strength decreased whereas their ductility increased when the added Fe increased. Because Fe acts as a γ-phase-stabilizing element for Co, Fe addition increases the stacking fault energy of the base alloy, resulting in the formation of the ε (hexagonal close-packed)-phase owing to the suppression of strain-induced martensitic transformation (SIMT), and improvements in ductility. No deterioration in corrosion resistance was observed following the addition of up to 8 mass% Fe to the base alloy. Based on these results, the addition of Fe to CCWN alloy may be considered an effective method to improve its mechanical properties, especially ductility, without impairing its corrosion resistance. The results of this study will be useful for the future development of Ni-free Co-Cr alloys for next-generation, small-diameter stents.

Augmenting Microstructure and Tribological Performance of Wire Arc Additive Manufactured PH13-8Mo Stainless Steel via TiC/TiB2 Nano-particles Incorporation

This study aimed to investigate the effect of TiC and TiB2 nano-inoculants addition on the microstructure and tribological behavior of PH13-8Mo stainless steel processed through wire arc additive manufacturing (WAAM). The incorporation of TiC/TiB2 inoculants demonstrated notable efficiency in mitigating the anisotropic wear and scratch response and enhancing wear resistance observed in the as-printed state. This improvement was ascribed to the refinement of the grain structure, disruption of the columnar structure, and increased content of the retained austenite. Notably, TiB2 inoculation exhibited superior grain refinement and achieved the highest hardness. However, the TiC-inoculated condition demonstrated the best wear resistance, attributed to its excellent combination of hardness and fracture resistance, and a higher contribution of strain-induced martensite transformation during wear testing. Additionally, the implementation of post-printing solutionizing and aging treatment was found to improve the scratch and wear resistance of the alloy, attributed to the formation of nano-sized β-NiAl precipitates. The main wear mechanism observed involved oxidation wear, adhesive wear, and three-body abrasive wear. The findings of this study highlight the significant potential of incorporating ceramic-based nano-particles for improving the wear resistance of WAAM PH13-8Mo components, particularly in demanding applications like injection molding dies where superior abrasion resistance is paramount.

Effect of Si additions on microstructure and properties of TiZrHfNbSix high-entropy alloys as potential biomaterials

High-entropy alloys (HEAs) have emerged as promising biomaterials owing to their favorable mechanical properties and resistance to corrosion. This investigation focuses on the impact of incorporating Si on the microstructure and properties of TiZrHfNbSix HEAs. The inclusion of Si leads to the formation of complex compositional silicides, showing multiple structures as the Si content varies. At low Si content, the BCC-silicide eutectic structure blocks the expansion of the shear zone during the deformation process, accounting for the increase in strength. The TiZrHfNbSi0.25 alloy presents a balanced combination of yield strength (∼1129 MPa) and plasticity (∼17%). Additionally, TiZrHfNbSi0.5 exhibited optimal corrosion resistance in Hank’s solution (Icorr = 1.713 × 10-7 A·cm-2, Ecorr = -0.327 V, 310 K) owing to the reduction in the number of protocells brought about by Si. The remarkable properties of TiZrHfNbSix HEAs renders it a highly promising option for application of silicide reinforcement in biomedical materials.

Effect of surfactant type and concentration on the gas-liquid mass transfer in biotrickling filters used for air pollution control

Volatile organic compounds (VOCs) emitted into the atmosphere negatively affect the environment and human health. Biotrickling filtration, an effective technology for treating VOC-laden waste gases, faces challenges in removing hydrophobic VOCs due to their low water solubility and therefore limited bioavailability to microorganisms. Consequently, the addition of (bio)surfactants has proven to be a promising strategy to enhance the removal of hydrophobic VOCs in biotrickling filters (BTFs). Yet, up to now, no single study has ever performed a mass transfer characterization of a BTF under (bio)surfactants addition. In this study, the effect of (bio)surfactant addition on the gas-liquid mass transfer characteristics of two BTFs was measured by using oxygen (O2) as a model gas. Through an empirical correlation, the mass transfer coefficients (kLa) of two hydrophobic VOCs, toluene and hexane, which are of industrial and environmental significance, were estimated. One BTF was filled with expanded perlite, while the other with a mixture of compost and wood chips (C+WC). Both BTFs were operated under different liquid velocities (UL: 0.95 and 1.53 m h-1). Saponin, a biological surfactant, and Tween 80, a synthetic surfactant, were added to the recirculating liquid at different critical micelle concentrations (CMCs: 0 - 3 CMC). The higher interfacial and surface area of the perlite BTF compared to the C+WC BTF led to higher kLaO2 values regardless of the operational condition: 308±18 - 612±19 h-1 versus 42±4 - 177±24 h-1, respectively. Saponin addition at 0.5 and 1 CMC had positive effects on the perlite BTF, with kLaO2 values two times higher compared to those at 0 CMC. Tween 80 exhibited a neutral or slightly positive effect on the mass transfer of both BTFs under all conditions. Overall, the CMC, along with the physical characteristics of the packing materials and the operational conditions evaluated explained the results obtained. This study provides fundamental data essential to improve the performance and design of BTFs for hydrophobic VOCs abatement.

Effect of zirconium addition on microstructural characteristics and nano-mechanical properties of P9 steel

Micro-alloying in steels has significant effects on microstructure and its properties. The main objective of the work is to understand the influence of zirconium (Zr) addition to P9 ferritic/martensitic (F/M) steel on phase stability, microstructure, and nanomechanical properties. The alloy compositions in this study were designed using thermodynamic calculations, based on which steels with Zr concentration in the range of 0.05–2 wt% were synthesized using vacuum arc melting. The cast alloy was subjected to thermo-mechanical treatments followed by austenitization and tempering treatments. Zr concentration of the steel was found to influence the nature of secondary phases formed, which were quantified through detailed synchrotron X-ray diffraction (XRD) analysis and also characterised extensively using electron microscopy techniques. Detailed structural analysis of the Fe23Zr6 phase using aberration corrected transmission electron microscopy is reported for the first time. The nano-mechanical properties of the heat-treated steels were evaluated using instrumented indentation (IIT) tests at room temperature with a sphero-conical indenter. A systematic variation in hardness and yield strength with Zr content of P9 steel was observed, which is correlated to the microstructural changes. The P9 F/M steel with optimum concentration of Zr, with better mechanical properties is proposed through this structure-property correlation study.

Effects of NiO addition on the microstructural evolution and performance of sintered magnesia aggregates

This study introduces a novel approach to enhance the properties of sintered magnesium oxide (MgO) aggregates by incorporating nickel oxide (NiO) powder as a solid-solution modification additive. The addition of NiO improves the densification of the specimens and promotes grain growth through the activation of sintering via the solid-solution reaction of MgO–NiO at high temperatures. The formation of the (Mg, Ni)O solid-solution structure enhances the strength of the specimens, while gradually reducing thermal conductivity. However, excessive addition of NiO (>6mol%) adversely affects the sintering properties of the specimens due to limited diffusive mass transfer rate during sintering and the Zener effect, resulting in diminished grain size and strength. Although thermal conductivity is not significantly affected, at 1000 °C, one specimen (MN-6) demonstrates a 61.03% decrease in thermal conductivity compared to a specimen without NiO addition. These findings suggest that the incorporation of a moderate amount of NiO enhances the corrosion resistance of the cement clinker of the specimens primarily by increasing densification, grain size, and high-temperature contact angle.

Effect mechanism of Nb addition on grain refinement and inhibition of discontinuous precipitation of Cu-15Ni-8Sn alloy

Cu-15Ni-8Sn-xNb alloys (x = 0, 0.2, 0.6 wt.%) were prepared using a medium-frequency induction melting furnace. The effect of Nb addition on grain refinement and inhibition of discontinuous precipitation (DP) in Cu-15Ni-8Sn alloys was systematically studied to elucidate the mechanism by which microstructural characteristics contribute to strength improvement. The results indicate that the increase the Nb content from 0 to 0.6 wt.% reduces the average grain size of the as-cast alloy from approximately 524.8 μm to approximately 81.3 μm, and significantly decreases the lamellar transition structure region (α+γ). During solution treatment, dispersed needle-like NbNi3 phases were observed in the Cu-15Ni-8Sn-0.2Nb alloy. After aging, the DP growth rate in the Cu-15Ni-8Sn-0.2Nb alloy was notably slower than those of the other alloys. This was attributed to NbNi3 phases at the grain boundaries hindering DP nucleation, with intragranular NbNi3 phases inhibiting DP growth. The phase transformation order of the solid solution Cu-15Ni-8Sn-0.2Nb at 673K aging is: spinodal structure → D022 ordered phase → L12 ordered phase → DP. The hardness and tensile strength of the Cu-15Ni-8Sn-0.2Nb alloy peaked at 338.3 HV and 725.42 MPa, respectively, after aging for 120 min. Using the Johnson–Mehl–Avrami–Kolmogorov(JMAK) and Arrhenius equations, the activation energies of DP in Cu-15Ni-8Sn-xNb (x = 0, 0.2, 0.6 wt.%) alloys were calculated to be 93.19, 148.64, and 98.33 kJ/mol, respectively. These values suggest that the diffusion of DP atoms in the Nb-containing alloys is hindered, which effectively inhibits DP formation.

Bio-oil production from hydrothermal liquefaction of algal biomass: Effects of feedstock properties and reaction parameters

In this study, two different algal biomass types, including fresh algal biomass (HS) and dewatered algal biomass (TH and CH), were selected to explore the effects of their properties and hydrothermal liquefaction (HTL) reaction parameters on bio-oil yields and quality. The obtained results showed higher bio-oil yields through the HTL process of the HS algal biomass than those obtained from the TH and CH algal biomass. The observed bio-oil yields increasing-decreasing trends with increasing reaction temperatures and times. The optimal reaction temperature and time were 325 °C and 30min, respectively. These conditions resulted in HS, TH, and CH algal biomass bio-oil yields of 31.6, 24.2, and 14.4wt%, respectively. The HS algal biomass-derived bio-oil exhibited higher H/C and HHV ratios, as well as lower N/C ratios, than those of the dewatered algal biomass-derived bio-oils. The bio-oil composition results demonstrated the enhancement effects of flocculant additions to the dewatered algal biomass on the bio-oil fractions. The TH and CH algal biomass-derived bio-oils exhibited substantially higher hydrocarbon contents than those in bio-oils of the HS algal biomass. In addition, the nitrogenous compound and hydrocarbon contents exhibited decreasing and increasing trends, respectively, with increasing reaction temperatures, improving the bio-oil quality.

New insights of the microcrack initiation induced by Mo addition in Ni-based single crystal superalloys during creep at 900 °C

Mo has received much attention in Ni-based single crystal superalloys as a main strengthening element at elevated temperatures above 1000 °C. However, the effects of Mo addition in new generation single crystal superalloys at medium temperature conditions are still not clear. This paper investigated the creep property at 900 °C and 392 MPa in a 4th generation Ni-based single crystal superalloy with different Mo contents, indicating that Mo addition decreased the creep life and induced large amounts of microcracks. Higher Mo content could weaken the interface strength by inducing more stacking faults, causing crack initiation along the interface. The elemental segregation along the stacking faults triggered the nucleation of other precipitates, which could further lead to cracks. The precipitation of topologically close-packed (TCP) phases introduced by more Mo addition caused crack initiation along the interfaces between the TCP phases and γ′ phase. By investigating the microcrack formation induced by Mo during creep at 900 °C, we provided a new perspective for the alloy design.

Microstructure evolution and tribological properties over a wide temperature range of Ni-based composite coatings with Ti3AlC2 addition

Ti3AlC2 MAX phase incorporated with Ni60A alloy powder in varying concentrations (0, 10wt.% and 20wt.%) were coated on S31008 NiCr stainless steel substrate using atmosphere plasma spraying technique in this work. Comparative investigation was conducted to examine the effects of Ti3AlC2 additions on the microstructure evolution, microhardness, and wide temperature range (room temperature to 800oC) tribological performance of the composite coatings. The findings demonstrated that the composite coatings were composed of γ-Ni, intermetallic hard metal borides, Ti3AlC2 and TiC phases, without any noticeable oxide phases. The 20wt.% Ti3AlC2 additions to the Ni60A alloy coating exhibited minimum imperfections in microstructure with a porosity drop of 65.8%, and the highest microhardness which was enhanced by 64% to 924 HV0.515. After introducing of Ti3AlC2, the coefficient of friction decreased and appeared to distinguish itself by remaining minimal and stable at low-medium temperatures compared with an increase of more than 70% at high temperatures. Ni60A-10 wt.% Ti3AlC2 coating resulted in the lowest friction coefficient of approximately 0.45 from room temperature to 400oC and it peaked to 0.78 at 800oC, reducing by 19.6% and 6% compared to non-composite coating, respectively. The wear resistance of the composite coating was considerably improved with the increment of Ti3AlC2, and the coating with 20wt.% Ti3AlC2 showed the most significant reduction in wear rate: 18.5% at room temperature, 45.2% at 200oC, 37.2% at 400oC, 60% at 600oC, 90.8% at 800oC. The lubricate layered Ti3AlC2 phases and the tribo-oxide film predominate composed of derivative NiO, Cr2O3 Al2O3 and TiO2 played a critical role in antifriction and wear resistance. The wear mechanisms were accordingly conducted as abrasion and adhesion wear at low-medium temperature and transferred into tribo-oxidation wear at elevated temperature.

Effect of Ni addition and bath temperature on electroless Cu microstructure in microvia preparation for HDI substrate

In this work, we investigated the microstructure evolution of electroless copper (Cu) deposition under different nickel (Ni) additions and reaction temperatures. It was found that the grain structure of electroless Cu is significantly influenced by the addition of Ni due to its inhibitory effect on Cu self-diffusion, while bath temperature had no impact on the electroless Cu grain growth. Additionally. nanovoids were observed in the electroless layer, primarily at the interface between the Cu trace and electroless layer, which is caused by the attachment of hydrogen bubbles during the electroless Cu reaction. These nanovoids do not affect the epitaxial grain growth in the microvia structure as observed through transmission electron microscopy (TEM). The nanovoids in the electroless Cu under different deposition conditions were also investigated through TEM images with the assistance of ImageJ. We found that the dimension of nanovoids initially increases with the reaction rate, as a result of the higher deposition rate introducing large hydrogen bubbles. However, as the reaction rate further increases, the size of the nanovoids stabilizes because larger hydrogen bubbles more easily escape the surface. This work may offer insights into potential approaches to enhance the quality of electroless Cu deposition for microvia preparation.

Physicochemical and Sensory Characteristics of Instant Pumpkin Soup with Variations of Porang Flour as a Thickener

Pumpkin (Cucurbita moschata) can be processed into instant soup. However, the weakness is its low viscosity. Porang flour as a thickening agent is expected to improve the shortcomings of instant pumpkin soup. This study aimed to investigate the effect of porang flour addition on the physical and sensory characteristics of instant pumpkin soup. This study used a non-factorial, completely randomized design, where the concentration of porang flour (0; 0.5; 1; 1.5 and 2%) was the independent variable. The result showed that the addition of porang flour caused an increase in moisture content, dietary fiber, viscosity, water solubility index and water absorption index in instant pumpkin soup. However, there was a decrease in the value of water activity, vitamin E, rehydration ratio, color, and sensory characteristics of instant pumpkin soup. In conclusion, adding 0.5% porang flour is recommended to produce instant pumpkin soup with good sensory and physicochemical properties.

Effect of Methanol and Polymer Additives on Large-Volume Dual Preconcentration by Isotachophoresis and Stacking (LDIS) in Straight-Microchannels

Effect of Methanol and Polymer Additives on Large-Volume Dual Preconcentration by Isotachophoresis and Stacking (LDIS) in Straight-Microchannels

Assessment of the Mechanical and Microstructural Performance of Waste Kraft Fibre Reinforced Cement Composite Incorporating Sustainable Eco-Friendly Additives

This study investigates the influence of limestone powder and metakaolin as sustainable eco-friendly additives on the properties and behavior of cementitious composite boards, with a focus on mechanical strength, physical properties, and microstructural characteristics. The experimental investigation begins with the characterization of the raw materials, including limestone powder, and metakaolin, to assess their particle sizes, elemental composition, and microstructural features. Cement composite boards were fabricated using an innovatively developed lab-simulated vacuum dewatering process, by varying the proportions of limestone powder and metakaolin as partial replacements for cement, along with waste kraft fibres as reinforcement. Mechanical testing was conducted to evaluate the flexural strength and behaviour of the composite boards according to standardized procedures. A microstructural analysis was performed using scanning electron microscopy (SEM) to examine the effect of additives on the cementitious matrix, fibrematrix interaction, and hydration products. The findings from the experimental study reveal insights into the influence of limestone powder and metakaolin on the mechanical properties and microstructure of waste kraft fibre-reinforced cement composite boards. Our analysis of the results shows that adding 9% limestone powder as partial cement replacement produces a 24% and 50% enhancement in flexural strength at 7 and 28 days of hydration, while that of metakaolin as partial cement replacement was optimum at 6% with an enhancement of 4% and 36%, respectively, at 7 and 28 days of hydration. The implications of these findings for the development of sustainable cementitious composite are discussed, including the potential benefits of using limestone powder and metakaolin as supplementary cementitious materials in waste kraft fibre-reinforced cement composite boards. Finally, recommendations for optimizing additive proportions are also provided to enhance the understanding and application of these materials in the construction and building industries.