Effect Of Pretreatment Research Articles

Correlation of Viscoelastic Properties with Water Status of Scallop Adductors During Heat Pump Drying: Effects of Ultrasound Pretreatment and Drying Conditions

Correlation of Viscoelastic Properties with Water Status of Scallop Adductors During Heat Pump Drying: Effects of Ultrasound Pretreatment and Drying Conditions

Pretreatment with inflammatory factors altered the secretome of human amniotic epithelial cells.

Human amniotic epithelial cells (hAECs) are novel and promising therapeutic agents for patients suffering from degenerative diseases. Studies have demonstrated that the therapeutic effects of hAECs mainly depend on their paracrine components. Currently, appropriate pretreatment is a widely confirmed strategy for enhancing the repair potential of stem cells; however, the effect of proinflammatory factor pretreatment on hAECs and their secretome is still unclear. In this study, we used the well-characterized proinflammatory factors tumor necrosis factor alpha (TNF-α) and interferon gamma (IFN-γ) to stimulate hAECs and analyzed the effect of TNF-α and IFN-γ on hAECs, including gene expression profile, paracrine proteins and miRNAs in exosomes. Results showed that TNF-α and IFN-γ pretreatment improved the viability of hAECs, but inhibited the proliferation of hAECs. TNF-α and IFN-γ pretreatment altered the gene expression profile of hAECs, and upregulated differentially expressed genes (DEGs) were predominantly enriched in biological adhesion, antioxidant activity and response to IFN-beta. In addition, TNF-α and IFN-γ pretreatment enhanced the paracrine secretion of cytokines by hAECs. The upregulated differentially expressed proteins (DEPs) were mainly enriched in tissue remodeling proteins and cytokine-cytokine receptor. Notably, the expression of miRNAs in exosomes from hAECs was also changed by TNF-α and IFN-γ pretreatment. The target genes of upregulated exosomal miRNAs substantially contributed to the response to stimulus, metabolic pathways and PI3K-Akt signaling pathway. Our findings improve our understanding of the biological characteristics of hAECs after proinflammatory factor pretreatment and provide novel insights to strengthen and optimize the therapeutic potential of hAECs and their secretome in regenerative medicine.

Effect of sandblasting and acid surface pretreatment on the specific capacitance of CuO nanostructures grown by hot water treatment for supercapacitor electrode applications.

Crystalline copper oxide (CuO) nanostructures with micro, nano, and micro-nano surface roughness were grown on Cu sheet substrates by a facile, scalable, low-cost, and low-temperature hot water treatment (HWT) method that simply involved immersing Cu sheet in DI water at 75 °C for 24 hours without any chemical additives. Various morphological features and sizes of CuO nanostructures were tuned by using different surface pretreatment techniques including acid treatment, sandblasting, or a combination of those two. The surface morphology of the prepared samples was analyzed by scanning electron microscopy (SEM). The crystal structure of the CuO nanostructures was investigated by X-ray diffraction (XRD) and Raman spectroscopy. To study the pseudocapacitive behavior, their potential supercapacitor performance, and equivalent series resistance, electrochemical analysis was done by cyclic voltammetry (CV) and electrochemical impedance spectroscopy for all the CuO/Cu samples in 1 M of Na2SO4 electrolyte. Among all, the best supercapacitive performance was achieved for CuO/Cu samples pretreated with Sandblasting followed by Acid treatment resulting in a specific capacitance of about 104 F/g. The electrode with the Sandblasted + Acid pretreated sample showed a maximum of ~ 69% capacitive retention after 2000 consecutive cycles. Our results indicate that CuO nanostructures on Cu substrates prepared with different surface pretreatment conditions and grown by HWT can be promising electrodes for supercapacitor device applications.

Quantitative assessment of ash effects on densifying lignocellulosic biomass with chemicals followed by autoclave (DLCA) pretreatment

Ash in lignocellulose is critical in interfering biomass pretreatment. Densifying Lignocellulosic biomass with Chemicals followed by Autoclave (DLCA) is a novel and efficient pretreatment method, whereas the specific effects of ash on DLCA pretreatment remain unclear. Herein, we quantitatively investigated the impacts of ash contents on the pretreatment effectiveness, enzymatic digestibility, and fermentability of DLCA pretreated corn stover (DLCA-CS). With the ash contents increasing from 3.36 % to 9.50 %, the DLCA-CS with addition of sulfuric acid (sa) showed decreased pretreatment efficiency and enzymatic digestibility, whereas these characteristics of DLCA-CS with addition of calcium hydroxide (ch) were improved with increasing ash contents. Further pH measurement during the biomass pretreatment revealed that the anions involved in ash neutralized the sulfuric acid, thus decreasing the pretreatment efficiency and enzymatic digestibility of DLCA(sa)-CS, while the anions can cooperated with the calcium hydroxide, thus increasing the pretreatment efficiency and enzymatic digestibility of DLCA(ch)-CS. The highest ethanol production of DLCA(sa)-CS (60.7 g/L) and DLCA(ch)-CS (66.5 g/L) at 25 % solid loading was achieved with a low ash content of 3.36 % without detoxification step. This study highlights the importance of controlling the ash contents for enhancing the efficiency of DLCA pretreatment.

Impact of Ohmic Heating and Ultrasound Pretreatments on Oil Absorption and Other Quality Parameters of Fried Potato

AbstractIn this study, the effect of pretreatments ((hot water blanching (HWB), ultrasound (US) and ohmic heating (OH)) on reducing the oil absorption of potato during frying and the changes in the quality parameters of the product ((total polyphenol (TP), in vitro digestion, total flavonoid (TF), antioxidant capacity (AC), chlorogenic acid (CA), textural and sensorial properties)) were investigated. The pretreatments applied significantly affected oil absorption and quality parameters of fried potato. The oil content of fried potatoes ranged from 26.06 to 32.01% depending on the pretreatment. OH-pretreated potato had the highest content of TP (41.27 mg GAE/100 g dry matter-DM), TF (32.89 mg RE/100 g DM) and CA (1.72 mg/100 g DM). However, there was no significant difference between the pretreatments in terms of bioaccessibility of polyphenols at the end of digestion. Also, AC value of fried potato pretreated by OH (124.13 mmol AAE/100 g DM) was higher compared to that of fresh potato (83.91 mmol AAE/100 g DM), but other two pretreatments caused a decrease in AC. The highest hardness was observed in HWB-treated potato strips. OH-treated potato had the best color parameters. Sensory data indicated that US-pretreated potato had the highest sensory scores followed by OH- and HWB-pretreated ones, respectively. Consequently, based on the above comprehensive quality evaluation, it can be suggested that OH pretreatment is a better choice for preparing deep fried potato.

Effects of pretreatment on the recycling properties of birch holocellulose paper

Effects of pretreatment on the recycling properties of birch holocellulose paper

Pretreatment of lignocellulosic biomass for bioethanol production

This review surveys recent progress in pretreatment methods for enhancing bioethanol production from lignocellulosic biomass. Various pretreatment techniques, including physical, chemical, and biological approaches, are evaluated for their efficacy in breaking down biomass structure and improving enzymatic digestibility. Key parameters influencing pretreatment effectiveness and integration with downstream processes are discussed. The review highlights promising strategies and identifies areas for further research to optimize bioethanol production from lignocellulosic feedstocks.

Minimally Invasive Semiconductor Laser Surgery Combined with 5-ALA Photodynamic Therapy for a Chronic Hyperplastic Candidiasis Patient Who Is Ineffective to Antifungal Therapy.

Background: Chronic hyperplastic candidiasis (CHC) is a chronic oral mucosal infection caused by Candida, which has potential for malignant transformation. Diagnosing CHC can be challenging due to its various manifestations. In addition, fungal treatments often prove to be ineffective, highlighting the urgent need for a new safe and efficient treatment approach. Given the potential of CHC to transform into malignancy, it is crucial to emphasize dynamic monitoring and follow-up after treatment. Objective: We attempted to investigate the effect of semiconductor laser pretreatment combined with 5-amino-levulinic acid (5-ALA) photodynamic therapy (PDT) for CHC. Methods: We presented the successful treatment of CHC with mild dysplasia in a 30-year-old man using semiconductor laser and 5-ALA PDT after antifungal therapy proved ineffective. Toluidine blue staining, autofluorescence imaging, and DNA image cytometry were combined to dynamically monitor the progress of the disease. Results: We have obtained positive outcomes with the use of laser combined with PDT treatment. The patients experienced only mild adverse reactions after the treatment, and there was no indication of recurrence or malignant transformation during the subsequent follow-up period, as observed through various auxiliary examinations. Conclusions: This case report suggests that semiconductor laser surgery combined with PDT could be a promising treatment option for patients with CHC who do not respond to antifungal therapy. In addition, the use of combined noninvasive examinations might provide a more accurate assessment of malignant transformation in patients with CHC.

Torrefaction and hydrothermal carbonization of waste from the paper industry: Effects of atmosphere choice and pretreatment with natural acidic reagent on fuel properties

The hydrothermal carbonization (HTC) and torrefaction of paper sludges and biological sludges from the paper industry were investigated and the effect of pretreatment of the samples with alcoholic vinegar was evaluated. The HTC was performed at two different reaction times, while the torrefaction took place at two different temperatures and two atmospheres. The gas analysis showed that the optimal torrefaction time for the N2 atmosphere can be determined by observing the CO2 content in the gas phase, which is not possible for the CO2 atmosphere. The TGA analysis showed that the choice of atmosphere influences further combustion, with samples torrefied at lower temperatures being more sensitive to it. The carbon (C) content in the thermally treated samples increases from 39.85 to 48.06 wt% for biological sludge and from 40.02 to 60.21 wt% for paper sludge. The H/C and O/C ratios decrease and approach the values of conventional fuels. The fuel ratio is higher for the torrefied samples. The higher heating value (HHV) increased from 17.4 to 21.4 MJ/kg for biological sludge and from 16.2 to 22.4 MJ/kg for paper sludge. Higher temperature and longer treatment time led to products with a higher HHV and a higher energy density. The highest energy yields were achieved during torrefaction at 250 °C, regardless of the atmosphere, with temperature and type of material having the greatest influence. Acidification of the samples or acidic media in the HTC affects the properties of the products by increasing the C content and HHV and affecting combustion.

Municipal sewage sludge dewatering performance enhancement by ultrasonic cavitation and advanced oxidation: A case study

ABSTRACT The number of published literature on the effect of ultrasonic cavitation and advanced oxidation pretreatment on the dewatering performance of anaerobically digested sludge is very limited. This study aims at determining the optimum operating conditions of large-scale filtering centrifuges in wastewater treatment plants. The optimum dose of hydrogen peroxide, ultrasonic power, ultrasonic duration, ultrasonic pulse and particle size distribution for improved dewatering performance were determined in this study. In addition, shear stress–shear rate and viscosity–shear rate rheograms were developed to show the rheological flow properties for varying ultrasonic power and treatment duration. Optimum sonication power, time, pulse and amplitude were determined to be 14 W, 1 min, 55/5 and 20%, respectively. At a pH of 6.8, the optimum concentration of hydrogen peroxide was found to be 43.5 g/L. The optimum hydrogen peroxide dose in the combined conditioning experiments was determined to be 500 mg/L at a pH of 3. Under these optimum conditions, capillary suction time was reduced significantly by 71.1%. This study helps to reduce polymer consumption and provides the optimum pretreatment and dewatering operating conditions, and better monitoring and control in the dewatering unit has significant impact in the overall economy of wastewater treatment plants.

Effect of Ultrasonic Pre-Treatment on the Reverse Flotation of Kaolinite From Bauxite

ABSTRACT Cationic reverse flotation of kaolinite from bauxite is an alternative to adequate high silica bauxites to the specifications of the Bayer process. However, the presence of clay minerals influences the slurries rheology decreasing the flotation performance. The objective of this work was to investigate the use of ultrasonic pre-treatment on kaolinite flotation and contrast it with the traditionally used chemical dispersant. Two bauxite samples were characterized in terms of chemical and mineralogical composition, as well as particle size distribution. Flotation was accomplished after conditioning with sodium polyacrylate and/or pre-treatment in ultrasound. Determinations of viscosity, sedimentation yield, and screening followed by the analysis of available alumina and reactive silica were also conducted. By increasing the concentration of solids to more than 20 wt.%, the slurry behavior changed from a Newtonian to a non-Newtonian behavior, the viscosity increased, and the flotation performance decreased. The use of chemical dispersant and ultrasonic pre-treatment increased the flotation performance. The ultrasound had a more marked effect in slurries with higher concentrations of solids. This result is related to the synergic effect of particle dispersion and reduction of the slime coating promoted by kaolinite onto gibbsite particles.

Protein and Polysaccharide Recovery from Shrimp Wastes by Natural Deep Eutectic Solvent Mediated Subcritical Water Hydrolysis for Biodegradable Film.

Environmental pollution is a significant problem due to the improper disposal of plastics and shrimp shells outdoors. Therefore, the synthesis of biodegradable film from waste materials is highly important. The novelty of this research lies in the extraction of protein hydrolysates and chitosan from shrimp shells, as well as the fabrication of biodegradable film from these materials. In this study, the composite films were produced using the solution casting method. Moreover, the combined effect of ultrasound pretreatments (UPT) and natural deep eutectic solvents (NADES) was investigated as extraction media, to determine their potential impact on shrimp waste subcritical water hydrolysis (SWH). Shrimp shells were submitted to UPT in NADES solution, followed by SWH at different temperatures ranging from 150 to 230°C under 3MPa for 20min. Then, the physiochemical properties and bioactivities of the hydrolysates were assessed to determine their suitability for use in biodegradable packaging films. Additionally, the physiochemical properties and bioactivities of the resulting hydrolysates were also analyzed. The highest amount of protein (391.96 ± 0.48mg BSA/g) was obtained at 190°C/UPT/NADES, and the average molecular size of the protein molecules was less than 1000Da with different kinds of peptide. Overall, combined UPT and SWH treatments yielded higher antioxidant activity levels than individual treatments. Finally, the application of composite films was evaluated by wrapping fish samples and assessing their lipid oxidation. The use of higher concentrations of protein hydrolysates significantly delayed changes in the samples, thereby demonstrating the film's applicability.

Sustainable wheat straw pretreatment process by self-produced and cyclical crude lactic acid

The purpose of this study was to investigate an environmentally friendly and recyclable pretreatment approach that would enhance the enzymatic digestibility of wheat straw. Wheat straw was pretreated using self-produced crude lactic acid obtained from enzymatic hydrolysate fermentation by Bacillus coagulans. Experimentally, crude lactic acid at low concentration could achieve a pretreatment effect comparable to that of commercial lactic acid. After pretreatment at 180 °C for 60 min with 2.0 % crude lactic acid, hemicellulose could be effectively separated and high recovery of cellulose was ensured, achieving cellulose recovery rate of 95.5 % and hemicellulose removal rate of 92.7 %. Excellent enzymatic hydrolysis was accomplished with a glucose yield of 99.7 %. Moreover, the crude lactic acid demonstrated acceptable pretreatment and enzymatic hydrolysis performance even after three repeated cycles. This not only effectively utilizes the pretreatment solution, but also offers insights into biomass pretreatment using other fermentable acids.

The effect of pretreatment on the adsorption efficiency of activated carbon

Activated carbon (AC) is a very diverse adsorbent material with high porosity, high surface area, and excellent performance in vapor phase adsorption. The pretreatment provides a guaranteed way for the efficient adsorption performance of AC, which can remove the impurities and improve the porosity of AC. In this study, the difference between acid pretreatment and alkali pretreatment of coconut shell carbon was systematically investigated. The effect of heating with stirring pretreatment and ultrasonic pretreatment after acid treatment were also researched. The Brunauer-Emmett-Teller (BET) specific surface area, the N2 saturation adsorption, and the porosity of AC by acid-ultrasonic pretreatment can reach 1094.30 m2g−1, 352.51 cm3 (STP) g−1, and 0.5453 cm3g−1, respectively, which are higher than that of acid-heating with stirring pretreatment and alkali-heating with stirring pretreatment. Combined with the Scanning Electron Microscope (SEM) and X-ray Photoelectron Spectroscopy (XPS) analysis data, AC by acid-ultrasonic pretreatment has a better microstructure and clearer aperture. Among the three methods of preprocessing, acid-ultrasonic pretreatment yields the most favorable results. This work provides a possible way for AC pretreatment.

Effect of thermal pretreatment and gastrointestinal digestion on the bioactivity of dry-cured ham bone enzymatic hydrolyzates

This study reports the effect of thermal pretreatment and the use of different commercial proteolytic enzymes (Protamex, Flavourzyme, Protana prime, and Alcalase) on the free amino acid content (FAA), peptide profile, and antioxidant, antidiabetic, antihypertensive, and anti-inflammatory potential (DPPH, FRAP, and ABTS assay, DPP-IV, ACE-I, and NEP inhibitory activities) of dry-cured ham bone hydrolyzates. The effect of in vitro digestion was also determined. Thermal pretreatment significantly increased the degree of hydrolysis, the FAA, and the DPP-IV and ACE-I inhibitory activities. The type of peptidase used was the most significant factor influencing antioxidant activity and neprilysin inhibitory activity. Protana prime hydrolyzates failed to inhibit DPP-IV and neprilysin enzymes and had low values of ACE-I inhibitory activity. After in vitro digestion, bioactivities kept constant in most cases or even increased in ACE-I inhibitory activity. Therefore, hydrolyzates from dry-cured ham bones could serve as a potential source of functional food ingredients for health benefits.

Comprehensive recycling of slag from the smelting of spent automotive catalysts

Spent automotive catalyst is a valuable source of platinum group metals (PGMs), making them crucial secondary resources. Currently, the main process for recovering PGMs from these catalysts is metal capture method. The smelting process would produce a significant amount of residual slags containing various components like SiO2, Al2O3, CaO, Fe2O3, Na2O, as well as high levels of heavy metals including Cr, Pb, and Ni. These slags are considered either solid waste or hazardous waste and usually disposed of in landfills, which can have detrimental effects on the environment. Furthermore, the smelting slags also contain approximately 2–5 % rare earth elements and trace amounts of precious metal elements. In this study, vacuum carbothermal reduction is employed to pretreat the smelting slags. This method not only successfully removes the heavy metal element lead, but also efficiently achieves the recovery of rare earths, and the enrichment of platinum group metals by mineral phase transformation of cerium-zirconium solid solution and in-situ iron capture. The lead removal rate exceeded 99 %, and the grade of precious metals in the enrichment process was approximately 12 times higher than the original material, with a recovery rate more than 90 %. The leaching rate of rare earths also increased from less than 50 % to more than 95 % after vacuum carbothermal reduction. The effect of vacuum carbothermal reduction pretreatment on the smelting slag phase was systematically studied, and the mechanism behind the increasing rare earth leaching rate due to this pretreatment was further analyzed.

Supercritical CO2 extraction increases the recovery levels of omega-3 fatty acids in Tetraselmis chuii extracts

Tetraselmis chuii is a microalgae marketed as ingredient meeting the acceptance criteria for novel foods established by the European Union and can be an important source of healthy fatty acids (FA). The aim of this research was to characterize the FA profile of T. chuii fractions obtained by supercritical carbon dioxide (SCCO2) extraction operating with two sequential co-solvents and to evaluate the effect of biomass pretreatment (freeze/thaw cycles followed by ultrasounds). T. chuii biomass was confirmed to be an important source of omega-3 FA, mainly due to the abundance of α-linolenic acid, and pre-treatment significantly improved the lipid yield. Other omega-3 FA, such as 16:3, 16:4, 18:4, 18:5, 20:3 and 20:5, were also detected in different proportions. When SCCO2 extraction of pretreated and un-pretreated T. chuii was compared with conventional solvent extraction, the nutritional quality indices of the extracts were improved by the use of SCCO2.

Enzymatic degradation of pea fibers changes pea protein concentrate functionality

Pea proteins are gaining increased interest from both the food industry as well as from consumers. Pea protein isolates (PPI) excel at forming meat-like textures upon heating while pea protein concentrates (PPC) are more challenging to transform into highly sought-after foods. PPCs are richer in dietary fibers (DF) and are more sustainable to produce than PPI. In this work, degradative enzymes were used to modify the functionality of PPC-water blends with a focus on texturization upon heating. Three enzyme solutions containing β-glucanases, hemicellulases, pectinases, xylanase, and cellulases were added to 65 wt% PPC blends. The effect of these enzymatic pretreatments was measured by monitoring the torque in a mixing reactor during blending, differential scanning calorimetry (DSC), high-pressure shear rheology (HPSR), and DF content and size analysis. Four endothermic peaks were detected in the DSC thermograms of PPC, namely at 63 °C , 77 °C , 105 °C and 123 °C . The first three peaks were attributed to phase transition and gelation temperatures of the starches and proteins constituting PPC. No endothermic peaks were measured for PPI blends. Enzyme solutions containing β-glucanases, hemicellulases, pectinases, and xylanases increased the endothermic energy of all peaks, hinting at an effect on the gelation properties of PPC. The same enzymes decreased the resistance to flow of PPC blends and induced a shift of the weight average molecular weight (Mw) distribution of soluble dietary fibers (SDF) towards smaller values while increasing the fraction of SDF by decreasing the insoluble dietary fiber (IDF) content. The solution containing cellulases did not change the DSC results or the viscosity of the PPC mixture, nor did it affect the IDF and SDF contents. On the other hand HPSR measurements of heated PPC samples up to 125 °C showed that all tested enzyme solutions decreased the complex viscosity of PPC-water blends to values similar to PPI-water blends. We demonstrated that degradative enzymes can enhance the functionality of less refined protein-rich ingredients based on pea and other vegetal sources. Using optimized enzyme blends for targeted applications can prove to be a key changer in the development and improvement of sustainable protein-rich foods.

Enhancing Infrared Drying of Red Dragon Fruit by Novel and Innovative Thermoultrasound and Microwave-Mediated Freeze-Thaw Pretreatments

This study investigated the effectiveness of novel and innovative pretreatments (NIP) using thermoultrasound and microwave-mediated freeze-thaw (TSFT, MWFT) for improving the mid-infrared drying of dragon fruit, as compared with recent pretreatment methods using cold plasma (CP), ultrasound (US), edible coating (EC), microwave and infrared blanching (MWB, IRB). Except for EC, all selected pretreatment methods induced ultrastructural changes, resulting in accelerated moisture removal and reduced drying time. In addition, all the pretreatments also induced modifications in colour, structure, and texture, with NIP demonstrating superior outcomes for colour, rehydration, shrinkage, and hardness properties. Blanching pretreatments (MWB and IRB) improved phytochemical and antioxidant properties, including total phenolics, betacyanin, betaxanthin, CUPRAC, hydroxyl radical scavenging, and ABTS, except for ascorbic acid, which was better preserved by TSFT. The study underscores the time-saving and quality enhancement advantage of NIP, over other recent methods for improving mid-infrared drying.

Effects of corona discharge plasma pretreatment on the drying kinetics and quality attributes of lily (Lilium davidii var. unicolor) bulbs

The objective of this study was to examine the impact of corona discharge plasma (CDP) treatments of different durations (1, 3, 5, and 10 min) on the drying kinetics and quality attributes of lilies, including color, enzyme activities, total phenols content (TPC), and antioxidant activity. The microstructure of lilies under different CDP conditions were also investigated. As a result, all CDP treatments enhanced the drying rate relative to untreated lilies, and the shortest drying time of 7 h was obtained at CDP-3 minute samples. CDP treatment led to a higher retention in the TPC of dried lilies. Microstructural analysis revealed the formation of irregular micropores on the surface of the lilies after CDP treatment, which was closely associated with the accelerated drying rate and improved bioactive substances of the dried product. In conclusion, CDP has emerged as a novel and beneficial pretreatment technique that accelerates the drying process and enhances the nutritional qualities of dried lilies.