Effect Of Fluorination Research Articles

Theoretical Investigations on the Hydroxyl-Initialized Oxidation of Hexafluoro-2-butyne in the Presence of Oxygen.

Hexafluoro-2-butyne (C4F6) is a potential eco-friendly alternative gas in plasma, refrigerants, and electrical insulation applications. Mechanisms for the reactions of C4F6 with OH/O2 have been revealed in detail using various theoretical methods including ROCBS-Q, RCCSD(T), multireference RS2C, and extrapolations to the complete basis-set limit with Aug-cc-pVnZ (n = T, Q, 5) basis sets. Rate coefficients and product branching ratios were predicted for a wide range of temperatures and pressures using the solution of master equations. The vibrationally adiabatic ground-state barrier for the initial C4F6 + OH association was best estimated to be 1.53-2.26 kcal/mol. Energetically preferable decomposition paths for the conformation-dependent C4F6OH adducts include six-center HF elimination, four-center proton migration, and C-C bond cleavage, but the collisional deactivation is dominant under ambient conditions. The subsequent oxidation of C4F6OH by O2 bifurcates in two orientations and proceeds without any well-defined barrier followed by the successive isomerization/elimination steps, forming perfluorobiacetyl to regenerate OH radicals or trifluoroacetic acid with trifluoroacetyl radicals. The OH-recycling path accounts for a branching ratio of 70% under ambient conditions. Theoretical rate coefficients are in good agreement with the available experimental results. The effect of fluorination on the reactivity of alkynes toward OH/O2 is discussed.

Fluorination effects on the physicochemical properties of the nanostructured tunable ionic liquids: [5F-PhMeTAZ]+ or [5H-PhMeTAZ]+ which one is the better choice?

One of the routine ways to design ILs with better and different properties is using of various combinations of the cations and anions. To the best of our knowledge combination of halogenated cations with various anions to make ILs with different properties has not been considered well yet. In this study, the effects of adding fluorine atom to the cation part of the triazolium based ionic liquids (TILs) generally presented as [5F-PhMeTAZ][X1–9] (X1= NO3−, X2= CF3CO2−, X3= Cl−, X4= C(CN)3−, X5= Tf2N−-cis, X6= N(CN)2−, X7= Tf2N−-trans, X8= ClO4− and X9= BF4−) were investigated. The structural, electronic and physicochemical characteristics of the fluorinated TILs (FTILs) were calculated and compared with those of corresponding non fluorinated TILs (HTILs) with the general formula of [5H-PhMeTAZ][X1–9] (X1= NO3−, X2= CF3CO2−, X3= Cl−, X4= C(CN)3−, X5= Tf2N−-cis, X6= N(CN)2−, X7= Tf2N−-trans, X8= ClO4− and X9= BF4−). All of the calculations were carried out using the same level of theory (M06-2X/6-311++G(d,p)) which is previously used for investigation of the above mentioned HTILs due to obtain comparable results. The binding energy, volumetric and electron density properties, electrostatic maps, electrochemical windows, crystal lattice energy, anodic and cathodic limits for newly designed FTILs are calculated and discussed. In this study we get help Natural bond orbital (NBO) analysis and Atoms in molecules (AIM) theory to get deeper understanding about quality and nature of bonding and nonbonding interactions which could be influenced ILs properties. Finally, some physical characteristics such as melting point, conductivity, enthalpy of vaporization, and critical-point temperature of the nine studied FTILs were estimated and also compared stand on the data obtained from quantum chemical calculations during this research.

Synthesis and study of fluorine-functionalized ZnTPPs

Five fluorinated zinc tetraphenyl porphyrins derivatives, fluorinated either on all ortho positions of the meso phenyl rings (Zn(II)-5,10,15,20-tetrakis(2,6-difluorophenyl)porphyrin) or in [Formula: see text]-positions with two, four, six or eight fluorine groups (2,3-difluoro-5,10,15,20-tetraphenylporphyrin, 7, 8,17,18-tetrafluoro-5,10,15,20-tetraphenylporphyrin, 7,8,12,13,17,18-hexafluoro-5,10,15,20-tetraphenyl- porphyrin and 2,3,7,8,12,13,17,18-octafluoro-5,10,15,20-tetraphenylporphyrin, respectively), were studied to probe the effect of fluorine in on-surface synthesis approaches. Additionally, bulkier substituents have been used in 7,8,17,18-tetrabromo-5,10,15,20-tetraphenylporphyrin and 7,8,17,18-tetramethyl-5,10,15,20-tetraphenylporphyrin, for a direct comparison with the corresponding fluorinated compounds. Reported are the synthesis and electronic structure characterization of the compounds, using UV-vis absorption and fluorescence spectroscopies as well as electronic structure calculations of the ground state molecular properties. Steric and electronic effects of fluorination are explored. For all molecules studied, substitution with fluorine maintains a planar tetrapyrrole macrocycle and shifts in the absorption spectra were consistent with calculated changes in the HOMOs and LUMOs energies of the molecules. In contrast, the bromo and methyl-substituted derivatives exhibit chemical instability and spectral shifts, compared to parent compound ZnTPP, consistent with structural distortions and accounted for calculations. The site-specific effects of fluorination on the electronic structure are discussed in detail.

Binding Energy of Triplet Excitons in Nonfullerene Acceptors: The Effects of Fluorination and Chlorination.

One strategy to improve the photovoltaic properties of nonfullerene acceptors (NFAs), employed in state-of-art organic solar cells, is the rational fluorination or chlorination of these molecules. Although this modification improves important acceptor properties, little is known about the effects on the triplet states. Here, we combine the polarizable continuum model with an optimally tuned range-separated hybrid functional to investigate this issue. We find that fluorination or chlorination of NFAs decreases the degree of the highest occupied molecular orbital-lowest unoccupied molecular orbital (HOMO-LUMO) overlap along these molecules. Consequently, the energy gap between T1 and S1 states, ΔEST = ES1 - ET1, also decreases. This effect reduces the binding energy of triplet excitons, which favors their dissociation into free charges. Furthermore, the reduction of ΔEST can contribute to mitigating the losses produced by the nonradiative deactivation of the T1 excitons. Interestingly, although Cl has a lower electronegativity than F, chlorination is more effective to reduce ΔEST. Since the chlorination of NFAs is easier than fluorination, Cl substitution can be a useful approach to enhance solar energy harvesting using triplet excitons.

Mesomorphic properties of cyanobiphenyl dimers with a substituted central malonate unit: overruling effect of fluorination

ABSTRACT Two series of C2-substituted dimers carrying a central C2-hexyl- or C2-nonafluorohexyl malonate and two cyanobiphenyls attached via alkoxy spacers of various lengths (n = 6–12) were synthesised, and the mesomorphic properties were studied by differential scanning calorimetry, polarising optical microscopyand X-ray diffraction (wide-angle and small-angle X-ray scattering). The C2-substituent dimers together with the spacer lengths had a pronounced influence on the phase behaviour. In case of C2-hexyl-substituted dimers, shorter spacers favoured N phases (n = 6–9), while longer spacers favoured SmA phases (n ≥ 9). In addition, decreased clearing temperatures were observed. In contrast, C2-nonafluorohexyl-substituted dimers suppressed N phases and displayed only SmA phases. Moreover, clearing temperatures and phase stabilities considerably increased. Based on the experimentally determined layer thickness, a packing model for the SmA phases was proposed, where C2-substituted dimers displaced mesophases with molecules in a Y-conformation. As a result, less stable mesophases for C2-hexyl-substituted dimers due to weakened intermolecular interactions and more stable mesophases for C2-nonafluorohexyl-substituted dimers due to the fluorophobic effect and nanosegregation were obtained.

Fluorination-Enhanced Surface Stability of Disordered Rocksalt Cathodes.

Cation-disordered rocksalt (DRX) oxides are a promising new class of high-energy-density cathode materials for next-generation Li-ion batteries. However, their capacity fade presents a major challenge. Partial fluorine (F) substitution into the oxygen (O) lattice appears to be an effective strategy for improving the cycling stability, but the underlying atomistic mechanism remains elusive. Here, using a combination of advanced transmission electron microscopy based imaging and spectroscopy techniques, the structural and chemical evolution upon cycling of Mn-based DRX cathodes with an increasing F content (Li-Mn-Nb-O-Fx , x= 0, 0.05, 0.2) are probed. The atomic origin behind the beneficial effect of high-level fluorination for enhancing the surface stability of the DRX is revealed. It is discovered that, due to the reduced O redox activity while with increasing F concentration, F in the DRX lattice mitigates the formation of an O-deficient surface layer upon cycling. For low F-substituted DRX, the O loss near the surface results in the formation of an amorphous cathode-electrolyte interphase layer and nanoscale voids after extended cycling. Increased F concentration in the DRX lattice minimizes both O loss and the interfacial reactions between DRX and the liquid electrolyte, enhancing the surface stability of DRX. These results provide guidance on the development of next-generation cathode materials through anion substitution.

Insight into the Enhanced Charge Transport in Quasi-2D Perovskite via Fluorination of Ammonium Cations for Photovoltaic Applications.

Fluorinated spacer cations in quasi-2D (Q-2D) perovskites have recently been demonstrated to improve the Q-2D perovskite solar cell (PSC) performance. However, the underlying mechanism of fluorination of organic cations on the improvement is still unclear. Here, using fluorinated benzylammonium (named F-BZA) as a spacer cation in Q-2D Ruddlesden-Popper (RP) perovskites, we deeply investigate the effect of fluorination of organic cations on perovskite crystallization and intermolecular interactions for improving the charge transport and device performance. It is found that fluorination of spacer cations can slow down the crystallization rate of perovskites, resulting in vertically aligned large grains. Moreover, the interaction between the adjacent spacer cations is further enhanced, constructing a new faster charge-transport channel with a lifetime of 77 ps. Accordingly, the carrier mobility is improved by an order of magnitude and a power conversion efficiency (PCE) of 16.82% is achieved in much more stable F-BZA-based Q-2D RP PSCs, 35% higher than that of BZA-based devices (12.39%). Our results elucidate the mechanism and its importance of fluorinating spacer cations for high-performance Q-2D PSC development.

Influence of Fluorine Substitution on the Photovoltaic Performance of Wide Band Gap Polymer Donors for Polymer Solar Cells.

The design and development of wide band gap (WBG) polymer donors are critical for achieving high power conversion efficiencies (PCEs) in polymer solar cells. In this work, four WBG polymer donors, Q4, Q5, Q6, and Q7, with different numbers and positions of fluorine substitution (n = 0, 2, 2, and 4, respectively) were prepared, and the effect of fluorination on their photovoltaic performance was systematically investigated. When blended with a small-molecule electron acceptor MeIC, the devices based on Q4, Q5, Q6, and Q7 showed PCEs of 10.34, 11.06, 5.26, and 0.48%, respectively. When coupled with a low band gap polymer acceptor PYIT to fabricate all-polymer solar cells (all-PSCs), while the other three polymers (Q5-Q7) exhibited much lower PCEs in the range of 0.12-6.71%, the Q4 polymer-based all-PSCs showed the highest PCE of 15.06%, comparable to that of the devices fabricated with the star polymer donor PM6 (PCE = 15.00%). Detailed physicochemical and morphological studies revealed that an over-substitution of F in Q7 results in undesired low-lying HOMO levels and phase separation with the acceptors, thus resulting in its inferior PCEs. Moreover, the less F-substitution and controlling of the positions of F-substitution position in Q4 and Q5 can improve the HOMO energy level matching as well as morphologies between these two polymers with the acceptors, which in turn gives rise to higher performances. Clearly, our results indicate that Q4 is a promising donor candidate for high-performance all-PSCs, and the fine-tuning of both the number and positions of F-substitution in the polymer backbone is essential in developing high-performance WBG polymer donors.

Evaluation of Radiation Resistance of Polystyrene Using Molecular Dynamics Simulation

The scission rates of polystyrene and fluorinated polystyrene irradiated in an irradiation facility with Co-60 γ-rays were determined using molecular dynamics simulation and gel permeation chromatography (GPC) molecular weight distributions. The prediction was based on the assumption that γ-ray energy is transferred to the initial velocity of the primary knock-on atom. We employed a molecular dynamics simulation procedure to compute the changes in bond length between the connections for selected values of the absorbed dose and compared the calculated values with measurements made on the irradiated samples. The samples were exposed to four different absorbed doses of 25, 50, 75, and 100 kGy. The scission process and scission ratio were simulated with LAMMPS with ReaxFF potential for each bond, and we compared the simulation results with the experimental data especially measuring average molecular weight to evaluate the effect of fluorination on radiation enhancement.

Fluorinated Metal-Oxide Thin-Film Transistors for Circuit Implementation on a Flexible Substrate

The effects of fluorination on amorphous indium gallium zinc oxide thin-film transistors and circuits fabricated on a polyimide flexible substrate were studied. Attributed to more effective passivation of donor defects for a given thermal budget, fluorination resulted in suppressed apparent short-channel effects and better uniformity of turn-on voltage with reduced negative shift after laser lift-off from a glass carrier substrate. As representative digital circuits, two-input four-output (2-4) decoders were fabricated and characterized to demonstrate the advantages of incorporating fluorination in the construction of circuit building blocks, leading to higher gain, wider noise margins, more tightly distributed transition voltage, and larger output swing.

Fluorination effects on bithiophene unit in benzodithiophene-4,8-dione based D-A type alternating copolymers for highly efficient polymer solar cells.

In this study, two D-A polymers consisting of benzodithiophene-4,8-dione and tetrathiophene with or without fluorination were synthesized to reveal the photovoltaic properties of fluorination effect on the polymer backbone. Polymer PDFTB with two fluorine atoms substituted on the backbone exhibits an enhanced π-π stacking effect, deeper HOMO energy level and better backbone planarity than PDTB without fluorine atom substitution. Devices based on PDFTB:ITIC show a power conversion efficiency of 4.39%, which is 15% higher than that of PDTB-based devices due to the higher hole mobility, optimized surface morphology and homogeneous phase separation of the active layer. These results suggest that the fluorination strategy is a facile way to design polymeric donors for solvent-processed polymer solar cells.

The fluorination effect on the transfection efficacy of cell penetrating peptide complexes

Cell penetrating peptides (CPPs) have been used as alternative delivery vectors to translocate therapeutic cargo molecules across cell membranes. One example of CPPs is the dTAT peptide, which has shown great promise in the design of highly efficient and low-cytotoxic gene vectors when condensed via “soft” calcium cross links. Here, we investigated the effect of fluorination on the formulation of dTAT complexes and explored their potential for pDNA delivery to cells. Fluorinated dTAT complexes achieve excellent gene transfection efficacy compared to fluorinated PEI polyplexes in A549, HeLa, and MCF-7 cell lines. Furthermore, the fluorinated dTAT complexes exhibit excellent serum resistance, high gene transfection efficacy even in 10% FBS medium, and no detectable cytotoxicity on transfected cells. The optimum NaF concentration (14 mM) resulted in an over 1000-fold enhancement in dTAT complexes (N/P 33) transfection efficiency. According to these findings, fluorination seems to be a potential strategy for creating gene vectors without requiring complex syntheses.

Fluorination and chlorination effects on the charge transport properties of the IDIC non-fullerene acceptor: an ab-initio investigation

Fused-ring electron acceptors end-capped with electron withdrawing groups have contributed to the ever-increasing power conversion efficiency of organic solar cells. Adding π-extensions and halogenating the end groups are two popular strategies to boost performance even further. In this work, a typical non-fullerene acceptor molecule, IDIC, is used as a model system for investigating the impact of the halogenation approach at the molecular level. The two end groups are substituted by fluorinated and chlorinated counterparts and their electronic and optical properties are systematically probed using ab-initio calculations. In gas phase, halogenation lowers the HOMO and LUMO energy levels and narrows the energy gap, especially for the chlorinated compound. Moreover, chlorinated IDIC exhibits the largest redshift and the smallest reorganization energy. Finally, crystal structures of the three compounds are constructed, revealing an improved transfer integral and transfer rate for the halogenated variants. Specifically, the chlorination strategy leads to an increase of 60% in transfer rate, compared to halogen-free IDIC.

Comparative study of fluorination effect on the linear carbonate molecule for reversible cycling of lithium metal batteries

A highly fluorinated carbonate molecule-based electrolyte is introduced to enhance the electrochemical performance of lithium metal batteries. The applied bis(2, 2, 2-trifluoroethyl) carbonate (DFDEC) demonstrates impressive performance enhancement by stable oligomeric/LiF-based bi-layered surface modification of Li metal. Li symmetric cell cycling shows prolonged stable electroplating/stripping of Li metal because of the formation of a stable protective bilayer on the Li surface. Furthermore, the negatively shifted HOMO energy level of DFDEC enhances the anodic stability in the high-voltage region on the high-nickel-containing positive electrode surface. Both sophisticated electrochemical characteristics of the DFDEC lead to the enhanced cycle performance of the lithium metal cell.

A′–A–π–D–π–A–A′ extended small-molecule photovoltaic donor based on fluorene-diketopyrrolopyrrole with an end-group fluorination effect

Compared with Flu(DPP)2, the PCEs of the devices based on A′–A–π–D–π–A–A′ type Flu(DPPsF)2 and Flu(DPPdF)2 increased by 51.4% and 63.4%, respectively, which is due to the synergistic effect of extended conjugate design and end-group fluorination.

Reducing the side-chain influences of isoindigo-based polymer donors by backbone fluorination in photovoltaic applications

The effect of synergistic structural engineering (asymmetric side chains and backbone fluorination) for polymer donors in photovoltaic applications is investigated in this study. Six isoindigo (IID)-based polymer donors with slightly different side-chain and backbone designs are composed of a bithiophene (BT) or fluorinated bithiophene moiety to form two series of polymers [PII2T (P1–P3) and PII2TF (P4–P6)] while symmetric/asymmetric side-chain combinations are composed of decyltetradecane branched alkyl side chain (DT) and siloxane-terminated side chain (SiO–C8). The results indicate the different side chain design and backbone fluorination modulate the energy levels, crystalline properties, and molecular packing behaviors of the polymers. P2 and P5 with asymmetric side chains are showed to deliver the highest power conversion efficiency (PCE) in the respective series of PII2T and PII2TF. The morphological analyses reveals that the mismatched side-chain geometry results in a face-on dominated packing to yield superior device performance. Meanwhile, the fluorinated polymers (P4–P6) show superior performance than the corresponding non-fluorinated polymers (P1–P3). Moreover, backbone fluorination largely reduces the performance difference between the polymers with symmetric side chains and asymmetric sides chains. This work demonstrates that the synergistic effect of asymmetric side chains and backbone fluorination can be a rational design towards high-performance conjugated polymers.

Fluorination Effect on the Gibbs Transfer Energy for Methylene Group from 1,2-Dichloroethane or 1,1,1,2,3,4,4,5,5,5-​Decafluoropentane to Water.

The ion-transfer reactions of alkyl and perfluoroalkyl carboxylate ions (CH3(CH2)n-2COO- and CF3(CF2)n-2COO-) at 1,2-dichloroethane (DCE) | water (W) and 1,1,1,2,3,4,4,5,5,5-decafluoropentane (DFP) | W interfaces were investigated. These ions gave reversible or quasi-reversible voltammetric waves due to their ion transfer across the interfaces, and the formal potentials and the formal Gibbs transfer energies from a non-aqueous solvent to water, ΔG°'tr,α→W (α = DCE and DFP), were determined. The ΔG°'tr,α→W for CH3(CH2)n-2COO- and CF3(CF2)n-2COO- linearly increased with n, allowing for estimating ΔG°'tr,α→W for methylene groups. The estimated value of ΔG°'tr,DCE→W for the -CH2- group was higher than that of ΔG°'tr,DCE→W for the -CH2- group, whereas the ΔG°'tr,DCE→W for the -CF2- group was lower than that of ΔG°'tr,DCE→W for the -CF2- group, indicating that the -CH2- (or -CF2-) group is more favorably (or unfavorably) solvated in the DCE phase compared to the DFP phase. From the estimated values, the fluorination effect of alkyl chains on partitioning the alkyl group between the biphase media has also been discussed.

Non-PGM Electrocatalysts for PEM Fuel Cells: A DFT Study on the Effects of Fluorination of FeNx-Doped and N-Doped Carbon Catalysts

Fluorination is considered as a means of reducing the degradation of Fe/N/C, a highly active FeNx-doped disorganized carbon catalyst for the oxygen reduction reaction (ORR) in PEM fuel cells. Our recent experiments have, however, revealed that fluorination poisons the FeNx moiety of the Fe/N/C catalytic site, considerably reducing the activity of the resulting catalyst to that of carbon only doped with nitrogen. Using the density functional theory (DFT), we clarify in this work the mechanisms by which fluorine interacts with the catalyst. We studied 10 possible FeNx site configurations as well as 2 metal-free sites in the absence or presence of fluorine molecules and atoms. When the FeNx moiety is located on a single graphene layer accessible on both sides, we found that fluorine binds strongly to Fe but that two F atoms, one on each side of the FeNx plane, are necessary to completely inhibit the catalytic activity of the FeNx sites. When considering the more realistic model of a stack of graphene layers, only one F atom is needed to poison the FeNx moiety on the top layer since ORR hardly takes place between carbon layers. We also found that metal-free catalytic N-sites are immune to poisoning by fluorination, in accordance with our experiments. Finally, we explain how most of the catalytic activity can be recovered by heating to 900 °C after fluorination. This research helps to clarify the role of metallic sites compared to non-metallic ones upon the fluorination of FeNx-doped disorganized carbon catalysts.

Higher-Energy Hexafluoroisopropanol···Water Isomer and Its Large Amplitude Motions: Rotational Spectra and DFT Calculations.

Rotational spectra of the 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP)···water complex were measured using a chirped pulse Fourier-transform microwave spectrometer. The spectral analyses, aided by density functional theory calculations, reveal two HFIP···water isomers: one previously reported, trans HFIP (HFIPt)···water (Phys. Chem. Chem. Phys. 2015, 119, 5650-5657), and a new isomer, gauche HFIP (HFIPg)···water. To confirm the identity of the new isomer, rotational spectra of seven of its deuterated species were also measured and analyzed. Both the experimental and theoretical pieces of evidence indicate that the intermolecular interaction with water preferentially stabilizes the HFIPg monomer configuration over the global minimum configuration, HFIPt. The relative energy difference between these monomeric forms is 4.1 kJ mol-1 and decreases to 2.5 kJ mol-1 in the respective monohydrates at the B3LYP-D3(BJ)/def2-QZVP level of theory. Both rigid and relaxed potential energy surface scans were carried out to gain insights into the large-amplitude water motions in HFIPg···water. The nonobservation of a water tunneling splitting in HFIPt···water has been explained to be a result of a barrier-less (after zero-point-energy correction) pathway for the water motion, whereas in HFIPg···water, a relatively large water tunneling barrier was identified as the cause of barely resolved water tunneling splittings. Noncovalent interaction and quantum theory of atoms and molecule analyses were used to evaluate the changes in HFIPg···water when going from the minimum to the transition state in terms of attractive interactions such as the OH···H and OH···F contacts. The effect of fluorination is discussed by comparing the vastly different binding topologies of isopropanol···water and HFIP···water.

Effects of anatase TiO2 morphology and surface fluorination on environmentally relevant photocatalytic reduction and oxidation reactions

Aiming at clarifying the interplay on TiO2 photoactivity between particle morphology and surface fluorination, the photocatalytic performance of anatase nanocrystals, characterized by a pseudo-spherical shape or a nanosheet structure, is investigated in both a reduction and an oxidation reaction, either in the absence or in the presence of added fluoride anions. Cr(VI) photocatalytic reduction is strongly favored by a large exposure of anatase {001} facets; however, surface fluorination leads in this case to a morphology-independent photoactivity decrease, due to the decreased adsorption of the reaction substrate. More interestingly, a beneficial synergistic effect between the platelet-like anatase morphology and TiO2 surface fluorination is clearly outlined in Rhodamine B photocatalytic degradation, possibly resulting from the intrinsic ability of fluorinated {001} anatase facets of boosting •OH radical mediated oxidation paths, due to their larger amount of surface –OH groups, as revealed using Fourier-transform infrared spectroscopy.