Effect Of Convective Heat Transfer Research Articles

CFD investigations of a shape-memory polymer foam-based endovascular embolization device for the treatment of intracranial aneurysms.

The hemodynamic and convective heat transfer effects of a patient-specific endovascular therapeutic agent based on shape memory polymer foam (SMPf) are evaluated using computational fluid dynamics studies for six patient-specific aneurysm geometries. The SMPf device is modeled as a continuous porous medium with full expansion for the flow studies and with various degrees of expansion for the heat transfer studies. The flow simulation parameters were qualitatively validated based on the existing literature. Further, a mesh independence study was conducted to verify an optimal cell size and reduce the computational costs. For convective heat transfer, a worst-case scenario is evaluated where the minimum volumetric flow rate is applied alongside the zero-flux boundary conditions. In the flow simulations, we found a reduction of the average intra-aneurysmal flow of > 85% and a reduction of the maximum intra-aneurysmal flow of > 45% for all presented geometries. These findings were compared with the literature on numerical simulations of hemodynamic and heat transfer of SMPf devices. The results obtained from this study can serve as a guide for optimizing the design and development of patient-specific SMPf devices aimed at personalized endovascular embolization of intracranial aneurysms.

Experimental Study on the Effect of Skin Friction Drag and Convective Heat Transfer for Viscoelastic and Pseudoplastic Fluid Flow

Drag Reducing Agents (DRAs) have a huge impact and major concern in engineering and industrial applications. It makes the fluid flow turbulent to laminar, dampens eddy reduces head loss by up to a certain limit, and saves pumping energy costs. Viscosity is the property that dampens eddy due to the viscous effect, which increases the fluidity up to a certain limit. Pseudoplasticity is the shear thinning effect that decreases viscosity when the flow rate increases. So, for the viscoelastic effect, we can increase the concentration up to a certain limit to reduce head loss. Still, during flow due to the pseudoplastic effect, the viscosity will start decreasing which is a negative effect. So, these combined effects are studied to reduce skin friction drag in the pipeline and save energy costs which will be convenient for the food industry, chemical, and medicine industries. In this investigation, investigation is carried out for 0.3 g/L, 0.2 g/L, and 0.15 g/L of xanthan gum in turbulent flow to observe the pressure drop and heat transfer rate. The study reveals that after increasing viscosity the pressure drop reduced significantly. Conversely, the heat transfer rate was also reduced due to the poor mixing effect. A higher performance and less vibration of the pump was also observed. It was concluded that the frictional pressure drop was reduced up to 85 % and the heat transfer rate was reduced by up to 90% by increasing the concentration of the DRA up to 0.3 g/L at 10 LPM than the pure water or base fluid as a working substance on the double pipe heat exchanger. As the heat transfer rate reduced up to 90% with reducing pressure drop another aim of the study was to establish a concentration and flowrate for which the heat transfer rate is maximum and it was found at a concentration of 0.15 g/L of DRAs (drag reducing agents) at 22 LPM (maximum flowrate at this setup).

Numerical Study on Heat Transfer and Thermal–Mechanical Performance of Actively Cooled Channel of All-Movable Rudder under Supercritical Pressure

The utilization of an actively cooled thermal protection system is widely recognized as an effective approach to decrease the temperature of components exposed to severe aerodynamic heating. In this study, two cooling schemes with different flow paths and structural configurations were proposed, and six cooling channel designs were developed by modifying the leading-edge details. A numerical analysis on the heat transfer and thermal–mechanical performance was conducted under actual flight conditions (30 km altitude, Mach 8). The results highlight an optimal design scheme that balances temperature control and minimized coolant flow rates. The channel flow field demonstrated its superiority by effective convective heat transfer and improved fluid mixing facilitated through recirculation zones and turbulence at the bends. Structural assessments showed that the optimal scheme not only provided better cooling but also preserved the structural integrity. Overall, the study offers a practical and effective thermal protection approach for air rudders subjected to severe heat.

Experimental study on energy storage characteristics of packed bed using different solid materials

The packed bed energy storage system can solve the mismatch between solar energy supply and demand at a low cost. The physical properties of storage materials have a decisive impact on the performance of storage systems. Different scenarios may require different storage materials. Studying the impact of storage materials on storage characteristics is crucial. However, the comparative analysis and research on different TES materials are focused on characterization and numerical simulation but less on packed bed TES experiments. This paper evaluates the thermal durabilities of three materials, including sintered ore particles, alumina balls, and rock particles, through thermal cycling tests. Through packed bed heat storage experiments, the energy storage characteristics and thermocline evolution characteristics of three beds under different operating conditions are compared and analyzed. The results indicate that all materials exhibit excellent thermal durabilities. A larger bed voidage and smaller bed heat capacity are beneficial for thermal diffusion in the bed. When reverse charging, the natural convection of air in the bed enhances the convective heat transfer effect, resulting in a higher charging power. The existence of natural convection promotes the mixing of cold air and hot air in the tank, increases the irreversibility of the process, and leads to a significantly lower efficiency in reverse flow compared to that in forward flow. When changing the airflow direction, the system overall exergy efficiencies of SOP, alumina, and rock bed decrease from 74.1 %, 72.4 %, and 77.2 % to 47.0 %, 39.9 %, and 45.8 %, respectively. Regardless of the airflow direction, the smaller the bed voidage and the larger the bed heat capacity, the better the maintenance characteristics of the thermocline.

Enhancing heat exchanger performance with perforated/non‐perforated flow modulators generating continuous/discontinuous swirl flow: A comprehensive review

AbstractHeat exchangers are crucial in transferring heat and finding applications across various industries. Numerous strategies have been devised to improve and optimize the heat transfer process within these systems. Among these, passive methods have garnered significant attention for their ability to operate without external power consumption. This article examines the recent experimental and computational studies conducted by researchers since 2018 on passive enhancement techniques, especially twisted tape, wire coil, swirl flow generator, and others, to boost the thermal efficiency of heat exchangers and aid designers in adopting passive augmentation methods for compact heat exchangers. Recently, researchers' new class of flow maldistribution devices, referred to as swirl flow devices, has gained attention; which enhances convective heat transfer by introducing swirl into the main flow and disrupting the boundary layer at the tube surface through alterations in surface geometry. Twisted tape inserts are devices that demonstrate better performance in laminar flow compared to turbulent flow. Conversely, other passive techniques like ribs, conical nozzles, and conical rings are generally more effective in turbulent flow than laminar flow. A recent research trend is the utilization of nanofluids in combination with other passive heat transfer enhancement techniques like turbulators, ribs, and twisted tape inserts in heat exchangers, which can reduce exergy losses and improve overall convective heat transfer coefficient and effectiveness of heat exchanger.

A temperature field model based on energy flow analysis of wet clutch sliding interface

A fluid-solid convective heat transfer model is constructed according to the velocity distributed calculation of lubricant in clutch groove cavity. Considering the characteristics of circumferential alternation of heat dissipation and generation area on separator plate surface,the effective energy flow characterization equations of convective hear transfer and heat generation at sliding interface are established. The non-heat source temperature field is proposed by effective convective heat transfer and heat conduction. Following the target constraint of continuous contact temperature, the temperature field change is solved during actual dynamic heat flux partition period. The tests with different intensity of heat generation and dissipation are designed, which indicates the reliability of model. The research provides a new method for the temperature field calculation of clutch.

Experimental investigation of forced convection heat transfer of heat exchangers with different pin geometries in in-line and staggered design

In this study, the effects of forced convection heat transfer on the surfaces of pin plate heat exchangers with different geometries modified to the heat exchanger form were experimentally investigated. A total of 8 pin fin plate heat exchangers, four of which are staggered and the other four are in-line, were used in the experiments. The heat transfer surface areas of the pin plate heat exchangers are produced equally. The only difference is their geometry, which is produced in four different shapes: triangle, circle, ellipse and square. The experiments were carried out at air velocities of 1 to 6 m/s with 1 m/s increments and at 10 W and 50 W input powers with 10 W increments. The staggered configuration of the pin fin plates demonstrated high performance in heat transfer. The study found that heat exchangers with cornerless pin plates have lower heat transfer compared to those with cornered pin plates. The pressure drops increased as the velocity of the coolant air increased, and the highest-pressure drop was observed in staggered triangular and elliptical pin plate heat exchangers. This research is considered innovative as it involves an experimental comparison between staggered and in-line pin plate heat exchangers in four different geometries, all with equal surface area.

Coupling drying of wet and heat field of corn pile based on porous medium model

AbstractCorn that are not properly dried can result in a lot of waste. Therefore, in this study, the corn pile was used as porous medium for hot air drying, and the coupling method of multiple physical fields was used to simulate and analyze the corn air‐drying silo with different initial conditions and different sizes. The results show that increasing the temperature of hot air could increase the temperature gradient inside corns and promote the evaporation of water. The higher the wind speed, the better the convective heat transfer effect between corn and air, thus improving the drying efficiency. The smaller the ratio of height to diameter of air‐drying silo, the more corn dried in the direction of hot air flow, resulting in poor drying effect. Increasing the inner diameter of the air‐drying silo will reduce the heat transfer efficiency. The lower the bed of the air‐drying silo, the closer the corns are to the hot air inlet, the faster the heating rate and the better the drying effect. The model has good performance and can be used as a mathematical tool to predict the change of maize wet heat field.Practical applicationsIn order to solve the integral problem of corn drying, the model uses corn grain pile as porous medium for hot air drying. The model investigated the changes of temperature field and humidity field during the drying process of grain pile in corn air‐drying silo. In addition, the characteristics of the model introduced in this study may qualify it for automatic control of corn air‐drying silo and online prediction of drying times to achieve the desired drying effect.

Experimental investigation of effects of convective heat transfer and thermal performance of impinging jet on a metal plate with porous media

This experimental investigation is aimed to evaluate the effects of convective heat transfer phenomena in an aluminium metal flat disc/plate placed below metal foam using a single round jet of air impinging in a confined region. The Jet impingement technique contains pressurized air, which is configured for certain specific application. It is designed to spray the fluid with the help of a nozzle on the surface of the disc or plate which is being heated or is being cooled. To understand the heat transfer phenomena in a metal plate with metal foams facing round air jet impingement; three metal foams of similar geometries but of different porosities and permeabilities are taken for study. Each experiment is performed with seven different flow rates and at two different heights with two different heat flux values. The recorded measurements are temperatures, pressure differences, flow rates, resistance voltages and currents, and time. The outcomes of the experimental data are analysed and compared results of all four distinct kinds of metal foams with different jet to plate height and at different heat fluxes. It is concluded that heat transfer efficiency may or may not increase depending upon the metal foam used. Overall, the conclusions are extremely useful in engineering.

Soret Effect on Magneto Hydrodynamic Free Convective Heat and Mass Transfer Effects Flow over an Inclined Plate Embedded in a Porous Medium

Soret Effect on Magneto Hydrodynamic Free Convective Heat and Mass Transfer Effects Flow over an Inclined Plate Embedded in a Porous Medium

Expression of Cconcern: A numerical study of CsSnIxBr3-x perovskite material as an electron transport layer (ETL), in the perovskite solar cell of a photovoltaic system by molecular dynamics method with LAMMPS software: The effects of external convective heat transfer

Expression of Cconcern: A numerical study of CsSnIxBr3-x perovskite material as an electron transport layer (ETL), in the perovskite solar cell of a photovoltaic system by molecular dynamics method with LAMMPS software: The effects of external convective heat transfer

Application of Caputo fractional approach to MHD Casson nanofluid with alumina nanoparticles of various shape factors on an inclined quadratic translated plate

The present study aims to examine the effect of convective heat transfer of nanofluid past an inclined plate. This paper scrutinizes heat transfer over an inclined surface of alumina nanofluids under the influence of radiation and magnetic fields with temperature-dependent thermophysical properties. The mathematical findings of velocity and temperature distributions are examined and visualized using non-dimensional flow parameters. The core of the research is to know the impact of using shape effects of alumina nanoparticles with a variety of base fluids like water, ethylene glycol, and engine oil. The outcomes concluded that the friction of the non-Newtonian viscous fluid decreased with increasing the inclination of the surface. The governing equations of the flow have been developed by using a few approximations such as Boussinesq's, and Roseland's. Using the dimensional analysis, the initial governing equations are simplified to dimensionless partial differential equations. A fractional model is developed using the Caputo fractional derivative. The solution of the proposed fractional partial differential equations is obtained in terms of special functions, Wright function, and Mittag-Leffler function by using the Laplace transformation method. Based on the interpretation, it is found that a reduction in velocity is observed with an increase in the angle of inclination i.e., γ = π/3 to γ = π/2. From the analysis, it is found that alumina/engine oil can carry higher temperatures than compared to other nanofluids and thus is a good option for heat transfer devices.

Numerical investigation of switchable cooling-heating-power trigeneration system based on flow channel control in summer

In this study, a numerical model is proposed via MATLAB software to respond to the dynamic indoor heating and cooling loads. This model combines spectral splitting PV/T systems and sky radiative cooling to achieve switchable heating, cooling, and electricity harvesting. Especially in the summer, the application of sky radiation cooling technology can lower the energy consumption of buildings. Meanwhile, the outdoor parameters and the operating factors are studied to explore the effects on the electric power and cooling power. Results indicate the threshold value of solar radiation for running daytime mode or nighttime mode is vital to output performance, and the optimal threshold value is recommended as 150W/m2 to regulate the switchable system. The flow velocity affects the convective heat transfer effects between the flowing water and the glass. As the flow velocity increases from 0.0005m/s and 0.0040m/s, the mean electric power improves from 41.3W to 54.1W and the cooling power improves from 62.6W to 96.4W respectively. Hence, it is suggested to employ a flow velocity of 0.0040 m/s to augment the system's capacity and adopt a channel thickness of 5mm, which can effectively reduce material costs without substantially compromising the power output.

Effect of porous fin parameters on the turbulent natural convection heat transfer in the side-heated cavity containing the internal heat source

In order to study the effect of porous fin parameters on the natural convection heat transfer in the side-heated cavity containing the internal heat source, the influence of the structural parameters of porous fins (length of porous fins l, installation position of porous fins s, Installation angle of porous fins θ) and the physical property parameters of porous fins (effective thermal conductivity Ke, Darcy number Da) on the natural convection heat transfer in the cavity was numerically analyzed by arranging a porous fin on the hot wall. The effect of the coupling effect of the structure parameters of porous fins was analyzed by the response surface method, and it was found that the coupling effect of the installation position and installation angle of porous fins had the most significant effect on the convective heat transfer in the cavity, the combination of the structural parameters of porous fins with the optimal convective heat transfer effect is l = 0.053 H, s = 0.373 H, and θ = 93.21°, which increases the average Nusselt number of the hot wall by 38.72% compared with no-fin structure; The effect of Darcy number and effective thermal conductivity of porous fins on the average Nusselt number of the hot wall surface is analyzed. The results of the study can guide the study of solar radiation in buildings, the internal temperature control of automobiles, and the study of the thermal performance of electronic components.

Heat pump and orc as part of an energy technology complex of water desalination

The article considers the processes of modeling the flow of a refrigerant and presents the results of numerical simulation of freon evaporation in a tubular evaporator. The results show the effect of convective heat transfer and bubble formation on the heat transfer coefficient. It is assumed that this technology can be used, among other things, as an element for water desalination. The possibility of using heat pumps and the organic Rankine cycle in the scheme of water desalination is considered. The authors propose to design such energy-technological complexes, starting from the stage of numerical simulation. The modeling results and the developed schemes presented to the attention of readers are part of a unified methodology for heat pumps and desalination systems.

Numerical simulation of convective heat transfer in the discharging process of external ice-melting ice storage systems

The external ice-melting ice storage system was widely used because of its advantages of reducing peak power consumption, reducing energy consumption and emissions, and fast ice melting speed. However, designing the external ice-melting ice storage system proved to be a challenge, and the structure and flow of the water distribution system needed to be fully considered. In particular, the problem of unstable outlet water temperature limited the practical application of the external melting ice storage system. Aiming at the problem of unstable outlet water temperature, a three-dimensional CFD phase change model was constructed in this paper. By comparing with the experimental data, the impact of varying water flow rates on the thermal and cooling properties of the was investigated. The results indicated that when the water flow rate was 226 ml/min for the system with an ice thickness of 74 mm, the outlet temperature of the ice storage tank was consistently below 5°C, the Nusselt number of ice and water remained constant, and the convective heat transfer effect was improved. The numerical simulation results provided guidance for the design and practical application of the water distribution system of the external melting ice storage system.

Quantifying the heat transfer effect of the axial turbine stator well cavity

A Thermal-Fluid-Structural model is presented for quantifying the heat generation by the labyrinth seal in the low-pressure turbine stator well cavity. The method combines windage heating and convective heat transfer effects for labyrinth seal design, making it possible to use the heat transfer boundary condition instead of adiabatic to do the computational fluid dynamic calculation. The solutions illustrate how the outlet total temperature may change depending on the seal pressure ratios, windage heating, and heat transfer coefficient. It is further demonstrated that with a fixed seal pressure ratio, the thermal boundary condition has little influence on the leakage flow rate of the seal. The total temperature rise is dependent on the thermal boundary conditions, including the stator/rotor wall temperature, heat transfer coefficient, and windage heat caused by air friction.

Novel selective adsorption cooling materials for heating cigarettes

Heated cigarettes are becoming trendy due to their advantage of not burning the tobacco material and thus reducing the amount of harmful ingredients released, while being able to leave the nicotine and tar content of the smoke untouched. However, the high temperature of the smoke as it enters the human mouth can affect the user experience. Therefore, the development of adsorption cooling materials for use in heated cigarettes is gradually becoming a hot topic. In this work, an adsorption cooling material based on embossed rod powder was prepared. It was found that compared with the commercial Yoga cooling material, the embossed rod powder based adsorption cooling material was able to reduce the maximum smoke temperature to 45.16 °C. In addition, it reduced the adsorption of nicotine by the cooling material, and increased the glycerol and nicotine content in the cooled smoke, which effectively promoted the taste of the smoke. Furthermore, the molecular simulation results found that the higher specific surface area and rich microscopic pore structure could increase the heat conduction area of the high-temperature flue gas, which enhanced the heat transfer effect of the flue gas. Finally, the periodic characteristic velocity pulsation destroyed the boundary layer formed by the fluid in the wall region, which increased the convective heat transfer effect between the fluid and the particles. The optimum sample 03 had the largest specific surface area and the lowest crystallinity, and thus had the best cooling effect. This work could provide some reference significance for the development of cooling materials for heating cigarettes.

Numerical study on the effect of optimizing the Trombe wall structure with built-in fins on improving building energy efficiency in severe cold region

In order to save heating energy and reduce carbon emission intensity, a floor heating room with built-in finned Trombe wall in Xining, Qinghai, a severe cold area, was taken as the research object. And ANSYS 2021 R1 was used to numerically investigate the effects of several major factors, such as fin height, fin transverse distance, fin longitudinal distance, fin inclined angle, fin shape, perforated shape and perforation ratio of perforated fin, on the average heat transfer coefficient (h) between the absorptive surface and the air in the interlayer. The results show that for fins with low heights, the enhancement effect of horizontal fins on the convective heat transfer of the absorptive surface of Trombe wall is greater than that of vertical fins. The enhancement effect of vertical fins on the convective heat transfer of the absorptive surface is more affected by fin transverse distance, while the enhancement effect of horizontal fins on the convective heat transfer of the absorptive surface is more affected by fin longitudinal distance. Besides, h shows a trend of first increasing and then decreasing with the increase of fin inclined angle, and reaches its maximum value of 5.89 W/(m2·K) at 45°. The fins with different shapes are equilateral triangular fins, semicircular fins, isosceles triangular fins and rectangular fins in descending order of their enhancement effect on the heat transfer of wall. Compared with solid fins, fins with circular holes can obtain a better convective heat transfer effect only when the open area ratio is 1:6. While fins with equilateral triangular holes can obtain better convective heat transfer effect as long as the open area ratio is greater than 1:7. Fins with elliptical holes do not significantly improve the heat transfer effect. On the basis of optimizing the fin layout and structure, the thermal performance of the improved Trombe wall during the 8:00∼16:00 period and its impact on indoor thermal comfort of the building were studied, and the energy-saving performance of the plan was discussed. Compared with the Trombe wall room with no fins, the improved Trombe wall can improve the heat teransfer efficiency and the building energy saving rate by 68.50 % and 53.57 %, respectively. The improved Trombe wall can only ensure the indoor thermal comfort in limited several hours, in the rest of time, the residents should add clothing to keep warm. These conclusions have an important effect of engineering guidance and great realistic meanings for promoting the process of solar building integration and achieving the “carbon peak and carbon neutrality” target.

Thermal interaction between water and liquid paraffin wax inside an intertwined enclosure: The role of natural convection in design of latent heat storage units

This work numerically investigated free convective heat transfer between water in a tank and melted paraffin-wax in an enclosure mounted inside the tank. The mediums were separated by thermally conductive walls. Three aspect ratios (AR = 0.3, 0.5, and 0.7) and three Rayleigh numbers (Ra = 104, 105, and 106) were examined for side- and bottom-heating orientations. The computations were conducted separately for the convection and conduction cases to observe the effects of natural convective heat transfer between the enclosures of the storage tank. The results showed that the heating orientation had a remarkable impact on the heat transfer between two fluids inside the intertwined enclosures. In the side-heating orientation, the variation of the average Nusselt number (Nu) with respect to Ra did not exhibit a consistent trend. It increased by 23.1 % when Ra increased from Ra = 104 to 105, but it decreased by 52.8 % when Ra was further increased from Ra = 105 to 106, at AR = 0.5. The Nu along the bottom wall of the inner enclosure was up to 24-folds of that along its side walls for the side-heating orientation and was 2.45-folds in the bottom-heating orientation. Furthermore, accumulation of hot fluid around the inner cavity walls, which occurred in side-heating cases, reduced convective heat transfer because of the low temperature gradient in these regions. Considering the outcomes of the present work, the bottom-heating orientation with AR = 0.5 can be recommended for future applications involving phase change processes as it ensured an effective thermal interaction between the two fluids.