Earlywood Fibres Research Articles

Characterization and within-tree variation of wood anatomy of Acacia melanoxylon

Introduction: A. melanoxylon wood has a large commercial application given its anatomical characteristics and mechanical properties. However studies on the anatomical characterisation of this species grown in Portugal are scarce. Objectives: To describe the transverse anatomical characteristics and their within-tree variation of A. melanoxylon trees growing in Portugal. Methods: 20 trees were analysed in transverse section for tree radial position (10%; 50%; 90%) and five height levels (base, 15%; 35%; 65%; 80%) in north and south directions. Measurements included: fibre diameter (m), fibre wall thickness (m), Runkle index; Flexibility index, vessel number (vessel number /mm2), porosity (%) and vessel width (m). Results: Earlywood fibres have lower wall thickness and higher lumen diameter than latewood fibres. Runkle and flexibility indexes confirm its potential for pulp and paper production. Porosity was lower near the pith as a result of a slight increase of vessel number with smaller size. Conclusion: Blackwood showed potential as an alternative species to supply the industry.

Fibre dimorphism: cell type diversification as an evolutionary strategy in angiosperm woods

Dimorphic fibres in angiosperm woods are designated when zones of two different kinds of fibres can be distinguished in transverse sections. The usage of most authors contrasts wider, thinner-walled, shorter (sometimes storied) fibres with narrower, thicker-walled fibres that have narrower lumina. The wider fibres can be distinguished in longitudinal sections from axial parenchyma, which usually consists of strands of two or more cells each surrounded by secondary walls (and thus different from septate fibres). This phenomenon occurs in some Araliaceae, Asteraceae, Fabaceae, Myrtales (notably Lythraceae), Sapindales (especially Sapindaceae), Urticales and even some Gnetales. Additional instances can doubtless be found, especially if instances of wide latewood fibres together with narrow earlywood fibres are included. There is little physiological evidence on differential functions of dimorphic fibres, except in Acer, in which hydrolysis of starch in the wide fibres is known to result in transfer of sugar into vessels early in the growing season. Starch storage in axial parenchyma may, in a complementary way, serve for embolism reversal and prevention and thus for maintenance of the water columns. Crystalliferous fibres (Myrtales, Sapindales) can be considered a form of fibre dimorphism that deters predation. Gelatinous fibres, often equated with tension wood, can also be considered as a form of fibre dimorphism. The evolutionary significance of fibre dimorphism is that a few small changes in fibre structure can result in the accomplishment of diversified functions.

Influence of Jack pine earlywood and latewood fibers on paper properties

Influence of Jack pine earlywood and latewood fibers on paper properties

MORPHOLOGICAL CHANGES OF JACK PINE LATEWOOD AND EARLYWOOD FIBERS IN THERMOMECHANICAL PULPING

The morphological changes of jack pine (Pinus banksiama) earlywood (EW) and latewood (LW) in thermomechanical pulping (TMP) were studied by light microscopy and scanning electronic microscopy. The results indicate that: under the mechanical forces in refining, the EW fibres tend to separate in the P/S1 interface, while separation of the LW fibres takes place commonly in the P/S1 and S1/S2 regions. The thick-walled LW fibres exhibit much more external fibrillation than the thin-walled EW. As a result, the LW fines contain more fibrillar component than EW fines. The EW fibers suffer more fiber cutting and splitting than the LW fibers. In addition, the thin-walled EW fibres show higher collapsibility and conformability than the LW counterparts.

Evaluation of a Novel Hydrocyclone Design for Pulp Fractionation

Abstract The fractionation efficiency and operating conditions of a novel hydrocyclone design were evaluated. The novel design comprised a modified inlet section, where the pulp suspension had to pass a narrow ring-shaped opening, and a very compact fractionation zone. The effect of feed concentration and fine fraction mass ratio was studied. The experiments were performed with fully bleached, unrefined and never-dried chemical softwood pulp. Fractionation efficiency was evaluated in terms of change in surface roughness of handsheets. Feed concentration had a large influence on the fractionation results, with a lower feed concentration resulting in improved fractionation efficiency. Furthermore, the surface roughness improved considerably for very low fine fraction mass ratios. Surprisingly, these ratios were much lower compared to the share of earlywood fibres in the pulp. The novel hydrocyclone design showed a lower thickening of the coarse fraction when compared with previous experiences with conventional hydrocyclones. Based on these results a hypothesis on the separation mechanism in a hydrocyclone was proposed. It suggests the existence of a radial variation in suspension composition in the fractionation zone, and most likely also a layer of unfractionated feed pulp along the outer wall. The existence of the gradient and the layer could explain that, especially at higher feed concentrations, a significant improvement in surface roughness was only obtained when the fine fraction ratio was significantly below the earlywood fibre share in the pulp.

Characterization of Jack Pine Early- and Latewood Fibers in Thermomechanical Pulping

The principal objective of this research was to study the morphological changes of Jack pine (Pinus banksiana) earlywood (EW) and latewood (LW) in thermomechanical pulping (TMP). The results indicate that EW fibers tend to separate at the P/S1 interface, whereas LW fibers commonly fail in the regions between the primary wall and the transition layer or outer layer of the secondary wall (P/S1) and between the outer and central layers of the secondary wall (S1/S2). LW fibers exhibit mostly intrawall failure and lower curl and kink indices, whereas EW fibers tend to fail in transwall mode (splitting) and suffer fiber cuttings. In addition, the thin-walled EW fibers show higher collapsibility and conformability than their thick-walled LW counterparts. Moreover, EW fines have higher surface lignin coverage, whereas LW fines have a higher specific volume (SV).

Fibre morphological effects on mechano-sorptive creep

The increased creep rate of paper under load during moisture cycling conditions as compared to that at high constant humidity is a problem in the use of packaging materials. In order to investigate the influence of morphological factors of the fibres on the occurrence and magnitude of this phenomenon, i.e. the occurrence of mechano-sorptive creep, studies on wood fibres isolated from different parts of spruce wood were performed. Thus, creep properties were studied on earlywood and latewood fibres from both juvenile wood and mature wood. In general, latewood fibres showed a higher degree of mechano-sorptive creep than earlywood fibres, and mature wood showed a higher degree of mechano-sorptive creep than juvenile fibres. The difference in mechano-sorptive creep rate between different fibres was shown to be correlated to the differences in fibril angle. The smaller the fibril angle the higher was the mechano-sorptive creep ratio. It was suggested that at fibril angles approaching 45° wood fibres do not exhibit mechano-sorptive creep.

The fracture behaviour of single wood fibres is governed by geometrical constraints: in situ ESEM studies on three fibre types

In situ tensile tests were performed in an environmental scanning electron microscope (ESEM) on earlywood, transition wood and latewood cells of Norway spruce (Picea abies [L.] Karst.). In order to examine the single wood fibres in a wet state, a specially designed tensile testing stage with a cooling device was built. The fracture behaviour of the cell types was studied at high resolution while straining. Different failure mechanisms were observed for the three tissue types. The thin-walled earlywood fibres showed tension buckling which gave rise to crack initiation and resulted in low tensile strength, whereas thick-walled latewood fibres predominately failed by transverse crack propagation without fibre folding.

Atomic force microscopy for the measurement of flexibility of single softwood pulp fibres

A new method based on the atomic force microscope has been developed to measure the lateral flexibility of single wood pulp fibres. In this method, individual wet pulp fibres from earlywood and latewood of Pinus radiata were placed on a newly designed two-point support, and the load and the deflection of fibres were measured under three-point bending test using a modified cantilever probe. The lateral flexibility values of the fibres were then calculated using propped cantilever beam theory. The results obtained indicate that earlywood fibres are substantially more flexible, and have a greater range of flexibility values than latewood fibres.

Separate Bleaching of Pulp Fractions Enriched in Earlywood and Latewood Fibers

Unbleached softwood kraft pulp was fractionated in hydrocyclones into a fine fraction, enriched in earlywood fibers, and a coarse fraction, enriched in latewood fibers. The response to individual bleaching chemicals and the bleachability in bleaching sequences of the pulp fractions was studied. The light absorption coefficient, light scattering coeffient, and brightness were higher in the unbleached fine fraction than in the coarse fraction. Hydrogen peroxide managed to reduce the light absorption coefficient of the earlywood enriched fine fraction more efficiently than that of the latewood enriched fraction. In the TCF‐sequence the light absorption coefficient of the fine fraction was reduced to the level of the coarse fraction at a given consumption of bleaching chemicals. In the ECF‐sequence the difference in light absorption coefficient remained between the fractions. At a given consumption of bleaching chemicals, the fine fraction had higher brightness than the coarse fraction, 2%‐ and 1%‐units on the ISO‐scale in the TCF and ECF bleaching sequence, respectively.

Micromechanical approach to wood fracture by three-dimensional mixed lattice-continuum model at fiber level

To investigate the fracture behavior of wood, the porosity and heterogeneities of its microstructure should be taken into account. Considering these features of wood microstructure in a continuum-based model is still a difficult problem and the lattice model might be an alternative. In the developed mixed lattice-continuum model, the probable crack propagation volume was modeled by defining a three-dimensional lattice of different beam elements and the other regions were considered as continuum medium. Different beam elements of lattice represented the earlywood fibers, latewood fibers, ray cells and bonding medium between the fibers. The proposed model was used to investigate the mechanism of mode I fracture in a small notched wood specimen in RL orientation. The resulting pre-peak and softening curve and also the crack opening trajectory in both cross-section and longitudinal-section in model were in good agreement with the experimental observations. This model shows the importance of considering the three-dimensional and distributed propagation of microcracks and main cracks in fracture stability. It was also shown that in mode I fracture, RL orientation, the main crack propagates in the earlywood ring.

Delignification and Bleaching Response of Earlywood and Latewood

The delignification response in cooking and the impact of bleaching on earlywood and latewood were studied. Spruce earlywood and latewood chips were pulped by the kraft process and subsequently treated with one bleaching chemical at a time. In cooking, latewood required a higher alkali charge to reach the same kappa number. No difference in the light absorption coefficient between the different fiber types was observed. After oxygen delignification the earlywood fibers had a higher light absorption coefficient at the same kappa number. The difference in light absorbing material was maintained when bleaching was performed with chlorine dioxide, ozone, and peracetic acid. Hydrogen peroxide decreased the light absorbing structures in the earlywood to the same level as for latewood. The earlywood pulp had a higher brightness at a given kappa number than the latewood. The higher brightness remained through all bleaching operations and was primarily due to a higher light scattering ability.

Three-dimensional modelling of wood fracture in mode I, perpendicular to the grain direction at fibre level

A coupled experimental and numerical modelling approach was used to investigate the mechanism of softwood fracture at the fibre level. First, a three-dimensional mixed lattice–continuum fracture model was developed to investigate the mechanism of wood fracture, taking into account the porosity of its structure and its heterogeneities at the fibre level. The critical volumes in the specimen where crack propagation was more probable were modelled by a lattice that could show the alternation of earlywood and latewood fibres, and the other regions were considered as the continuum medium. The proposed model was used to investigate the mode I fracture of a small softwood sample in RL orientation. Secondly, a method was developed for microscopic observation of the crack trajectory and investigating the mechanism of initiation and propagation of cracks. This approach was used for microscopic investigation of the fracture behaviour of spruce specimens in mode I and RL orientation. The results of the numerical study were compared with the experimental results. The prepeak and postpeak behaviour of the obtained stress–displacement curve and also the crack opening trajectory in cross-section and longitudinal section in the model and experiments were in good agreement. Both the model and the microscopic observation showed that in mode I fracture and RL orientation, the main trajectory of the crack propagates in the earlywood ring.

Changes in the fiber wall during refining of bleached pine kraft pulp

Abstract The effect of refining on the fiber wall was studied for bleached kraft pulp fractions from pine first thinnings and pine sawmill chips. Hydrocyclone fractionation of both pulps produced fractions enriched in earlywood and latewood fibers. Some external fibrillation but no changes in fiber wall thickness were observed for the thin-walled earlywood fibers during refining. Refining the thick-walled latewood fibers led to extensive external fibrillation and a decrease in fiber wall thickness. The pore structure of the fiber wall opened up during refining for all pulp fractions. Earlywood fibers were more porous than latewood fibers, and fibers from first thinnings more porous than those from sawmill chips. The earlywood fibers from first thinnings had more large pores than the other fiber fractions. In the region of the smaller pores, the pore volume did not change significantly with refining, whereas in the region of the larger pores it increased markedly. In all the fractions investigated, specific hydrolytic enzymes hydrolyzed cellulose more easily after refining. This is an indication of an increase in cellulose surface area and/or disordering of cellulose as a result of refining, probably due to local disorder of the cellulose in the fibril aggregates. Bonding developed most strongly for the earlywood fiber fraction from first thinnings. This is concluded to be due to a combination of fiber dimensions and fiber wall porosity.

The fibre characteristics of shives initiating web rupture

The thesis comprises three parts: Existing methods for characterisation of fibre crosssections have been improved, and new methods have been developed. These methods have then been applied to study the effects of wood characteristics and the pulping process on mechanical pulp fibres. Links have been established between fibre structure and paper properties such as surface smoothness and light scattering coefficient.New methods, based on SEM-images and image analysis, are described for providing cross-sectional fibre dimensions for large fibre populations, for wood tracheids (app. 60 000 tracheids in a wood trunk) and for processed pulp fibres (app. 1000 fibres per sample). The methods are suited e.g. for evaluation of changes in the fibre cross-sections from wood to the finished paper, or for mapping of fibre parameters within and between growth rings in a wood trunk. The treatment of data is discussed, showing how one may examine the changes in different groups of fibres (earlywood fibres, latewood fibres, split fibres) throughout a process.It is known from the literature that groundwood-based paper is superior to TMP-based paper with respect to printability. Fibres from SGW and PGW-pulp were found to be much more split in the longitudinal direction than TMP-fibres at comparable freeness. Intact groundwood fibres had thicker walls than intact TMP-fibres, but nevertheless super calendered hand sheets made from groundwood fibres were less roughened by moistening than were TMP-based sheets. Both for groundwood pulps and for TMPpulps, it was shown that reduced fibre wall thickness and increased fibre splitting was beneficial for improved surface smoothness and opacity.Latewood defibrate easier than earlywood during refining. In the case of grinding, there was no particular preference for earlywood or latewood to be defibrated. Reject refining of groundwood reject was, however, found to be very important for defibration of latewood-containing shives. Pulps made from a raw material with more compact fibres (high wall area to lumen area ratio) were found to defibrate easier, and contain less shives. It was found that refining tends to reduce wall thickness most on thickwalled parts of the fibre, thus causing a reduction of the wall thickness variation around the perimeter.Earlywood fibres were found to be preferentially split during refining. Most fibre splitting occurs during the primary stage, while the fibres are firmly attached to chips or fibre bundles. Latewood fibre wall thickness decreases considerably more than earlywood fibre wall thickness during refining. It seems that choosing an appropriate raw material is more effective than using excessive energy on reducing the wall thickness of thickwalled fibres. Earlywood fibres became more flattened during refining compared to latewood fibres, possibly due to repeated compressions and relaxations in the refiner.The energy consumption to a given freeness was found to be considerably larger for Scots Pine than for Norway Spruce. However, the fibre transverse dimensions did not differ much between Norway Spruce and Scots Pine. Pine pulps were far less developed than spruce pulps at similar energy level. A possible explanation for the large energy consumption may be that redistribution of extractives at the fibre surface could reduce friction in the refiner. This hypothesis should be further explored.The results in this study improve the knowledge of which fibre parameters that matter for surface smoothness and opacity of wood-containing publication paper. Further, this study elucidates how important fibre parameters such as wall thickness and fibre splitting are altered during a refining process. The results may be utilized to identify possible ways of modifying the TMP-process in order to produce paper with improved surface smoothness and opacity.

Assessment of transverse dimensions of wood tracheids using SEM and image analysis

The thesis comprises three parts: Existing methods for characterisation of fibre crosssections have been improved, and new methods have been developed. These methods have then been applied to study the effects of wood characteristics and the pulping process on mechanical pulp fibres. Links have been established between fibre structure and paper properties such as surface smoothness and light scattering coefficient.New methods, based on SEM-images and image analysis, are described for providing cross-sectional fibre dimensions for large fibre populations, for wood tracheids (app. 60 000 tracheids in a wood trunk) and for processed pulp fibres (app. 1000 fibres per sample). The methods are suited e.g. for evaluation of changes in the fibre cross-sections from wood to the finished paper, or for mapping of fibre parameters within and between growth rings in a wood trunk. The treatment of data is discussed, showing how one may examine the changes in different groups of fibres (earlywood fibres, latewood fibres, split fibres) throughout a process.It is known from the literature that groundwood-based paper is superior to TMP-based paper with respect to printability. Fibres from SGW and PGW-pulp were found to be much more split in the longitudinal direction than TMP-fibres at comparable freeness. Intact groundwood fibres had thicker walls than intact TMP-fibres, but nevertheless super calendered hand sheets made from groundwood fibres were less roughened by moistening than were TMP-based sheets. Both for groundwood pulps and for TMPpulps, it was shown that reduced fibre wall thickness and increased fibre splitting was beneficial for improved surface smoothness and opacity.Latewood defibrate easier than earlywood during refining. In the case of grinding, there was no particular preference for earlywood or latewood to be defibrated. Reject refining of groundwood reject was, however, found to be very important for defibration of latewood-containing shives. Pulps made from a raw material with more compact fibres (high wall area to lumen area ratio) were found to defibrate easier, and contain less shives. It was found that refining tends to reduce wall thickness most on thickwalled parts of the fibre, thus causing a reduction of the wall thickness variation around the perimeter.Earlywood fibres were found to be preferentially split during refining. Most fibre splitting occurs during the primary stage, while the fibres are firmly attached to chips or fibre bundles. Latewood fibre wall thickness decreases considerably more than earlywood fibre wall thickness during refining. It seems that choosing an appropriate raw material is more effective than using excessive energy on reducing the wall thickness of thickwalled fibres. Earlywood fibres became more flattened during refining compared to latewood fibres, possibly due to repeated compressions and relaxations in the refiner.The energy consumption to a given freeness was found to be considerably larger for Scots Pine than for Norway Spruce. However, the fibre transverse dimensions did not differ much between Norway Spruce and Scots Pine. Pine pulps were far less developed than spruce pulps at similar energy level. A possible explanation for the large energy consumption may be that redistribution of extractives at the fibre surface could reduce friction in the refiner. This hypothesis should be further explored.The results in this study improve the knowledge of which fibre parameters that matter for surface smoothness and opacity of wood-containing publication paper. Further, this study elucidates how important fibre parameters such as wall thickness and fibre splitting are altered during a refining process. The results may be utilized to identify possible ways of modifying the TMP-process in order to produce paper with improved surface smoothness and opacity.

Changes induced in early- and latewood fibres by mechanical pulp refining

The thesis comprises three parts: Existing methods for characterisation of fibre crosssections have been improved, and new methods have been developed. These methods have then been applied to study the effects of wood characteristics and the pulping process on mechanical pulp fibres. Links have been established between fibre structure and paper properties such as surface smoothness and light scattering coefficient.New methods, based on SEM-images and image analysis, are described for providing cross-sectional fibre dimensions for large fibre populations, for wood tracheids (app. 60 000 tracheids in a wood trunk) and for processed pulp fibres (app. 1000 fibres per sample). The methods are suited e.g. for evaluation of changes in the fibre cross-sections from wood to the finished paper, or for mapping of fibre parameters within and between growth rings in a wood trunk. The treatment of data is discussed, showing how one may examine the changes in different groups of fibres (earlywood fibres, latewood fibres, split fibres) throughout a process.It is known from the literature that groundwood-based paper is superior to TMP-based paper with respect to printability. Fibres from SGW and PGW-pulp were found to be much more split in the longitudinal direction than TMP-fibres at comparable freeness. Intact groundwood fibres had thicker walls than intact TMP-fibres, but nevertheless super calendered hand sheets made from groundwood fibres were less roughened by moistening than were TMP-based sheets. Both for groundwood pulps and for TMPpulps, it was shown that reduced fibre wall thickness and increased fibre splitting was beneficial for improved surface smoothness and opacity.Latewood defibrate easier than earlywood during refining. In the case of grinding, there was no particular preference for earlywood or latewood to be defibrated. Reject refining of groundwood reject was, however, found to be very important for defibration of latewood-containing shives. Pulps made from a raw material with more compact fibres (high wall area to lumen area ratio) were found to defibrate easier, and contain less shives. It was found that refining tends to reduce wall thickness most on thickwalled parts of the fibre, thus causing a reduction of the wall thickness variation around the perimeter.Earlywood fibres were found to be preferentially split during refining. Most fibre splitting occurs during the primary stage, while the fibres are firmly attached to chips or fibre bundles. Latewood fibre wall thickness decreases considerably more than earlywood fibre wall thickness during refining. It seems that choosing an appropriate raw material is more effective than using excessive energy on reducing the wall thickness of thickwalled fibres. Earlywood fibres became more flattened during refining compared to latewood fibres, possibly due to repeated compressions and relaxations in the refiner.The energy consumption to a given freeness was found to be considerably larger for Scots Pine than for Norway Spruce. However, the fibre transverse dimensions did not differ much between Norway Spruce and Scots Pine. Pine pulps were far less developed than spruce pulps at similar energy level. A possible explanation for the large energy consumption may be that redistribution of extractives at the fibre surface could reduce friction in the refiner. This hypothesis should be further explored.The results in this study improve the knowledge of which fibre parameters that matter for surface smoothness and opacity of wood-containing publication paper. Further, this study elucidates how important fibre parameters such as wall thickness and fibre splitting are altered during a refining process. The results may be utilized to identify possible ways of modifying the TMP-process in order to produce paper with improved surface smoothness and opacity.

Fibre characteristics of some mechanical pulp grades

The thesis comprises three parts: Existing methods for characterisation of fibre crosssections have been improved, and new methods have been developed. These methods have then been applied to study the effects of wood characteristics and the pulping process on mechanical pulp fibres. Links have been established between fibre structure and paper properties such as surface smoothness and light scattering coefficient.New methods, based on SEM-images and image analysis, are described for providing cross-sectional fibre dimensions for large fibre populations, for wood tracheids (app. 60 000 tracheids in a wood trunk) and for processed pulp fibres (app. 1000 fibres per sample). The methods are suited e.g. for evaluation of changes in the fibre cross-sections from wood to the finished paper, or for mapping of fibre parameters within and between growth rings in a wood trunk. The treatment of data is discussed, showing how one may examine the changes in different groups of fibres (earlywood fibres, latewood fibres, split fibres) throughout a process.It is known from the literature that groundwood-based paper is superior to TMP-based paper with respect to printability. Fibres from SGW and PGW-pulp were found to be much more split in the longitudinal direction than TMP-fibres at comparable freeness. Intact groundwood fibres had thicker walls than intact TMP-fibres, but nevertheless super calendered hand sheets made from groundwood fibres were less roughened by moistening than were TMP-based sheets. Both for groundwood pulps and for TMPpulps, it was shown that reduced fibre wall thickness and increased fibre splitting was beneficial for improved surface smoothness and opacity.Latewood defibrate easier than earlywood during refining. In the case of grinding, there was no particular preference for earlywood or latewood to be defibrated. Reject refining of groundwood reject was, however, found to be very important for defibration of latewood-containing shives. Pulps made from a raw material with more compact fibres (high wall area to lumen area ratio) were found to defibrate easier, and contain less shives. It was found that refining tends to reduce wall thickness most on thickwalled parts of the fibre, thus causing a reduction of the wall thickness variation around the perimeter.Earlywood fibres were found to be preferentially split during refining. Most fibre splitting occurs during the primary stage, while the fibres are firmly attached to chips or fibre bundles. Latewood fibre wall thickness decreases considerably more than earlywood fibre wall thickness during refining. It seems that choosing an appropriate raw material is more effective than using excessive energy on reducing the wall thickness of thickwalled fibres. Earlywood fibres became more flattened during refining compared to latewood fibres, possibly due to repeated compressions and relaxations in the refiner.The energy consumption to a given freeness was found to be considerably larger for Scots Pine than for Norway Spruce. However, the fibre transverse dimensions did not differ much between Norway Spruce and Scots Pine. Pine pulps were far less developed than spruce pulps at similar energy level. A possible explanation for the large energy consumption may be that redistribution of extractives at the fibre surface could reduce friction in the refiner. This hypothesis should be further explored.The results in this study improve the knowledge of which fibre parameters that matter for surface smoothness and opacity of wood-containing publication paper. Further, this study elucidates how important fibre parameters such as wall thickness and fibre splitting are altered during a refining process. The results may be utilized to identify possible ways of modifying the TMP-process in order to produce paper with improved surface smoothness and opacity.

Degradation of the Gelatinous Layer in Aspen and Rubberwood by the Blue Stain Fungus Lasiodiplodia Theobromae

Studies on the degradative ability of the blue stain fungus Lasiodiplodia theobromae (Pat.) Griffon ' Maublanc have shown several strains to cause significant weight losses (c. 20%) in wood of temperate and tropical species, aspen (Populus tremula) and rubberwood (Hevea brasiliensis), both species that commonly form tension wood. In addition to the consumption of soluble carbohydrates, major changes occurred in the ultrastructure of fibre cell walls, with a rapid attack of the G-layer of the gelatinous fibres. Following G-layer degradation, earlywood fibres of both species showed true cell wall degradation with pronounced erosion attack, suggesting that prior destruction of the G-layer afforded greater accessibility and ease of attack of the outer secondary cell wall layers.

Seasonal Changes in the Distribution of Water in the Outer Growth Rings of Fraxinus Mandshurica Var. Japonica: A Study By Cryo-Scanning Electron Microscopy

Seasonal changes in the distribution of water in the outer growth rings of Fraxinus mandshurica var.japonica were visualised by cryo-scanning electron microscopy using samples in which water was freeze-fixed in the living trunk . During the growing season from mid-May to late-July when formation ofxylem progressed steadily, all cell lumina of the newly forming xylem elements were filled with water. From August to October, water was lost from the lumina of wood fibres in the current-year xylem. Loss of water from wood fibres began in August at the initial zone of the earlywood, and progressed toward the cambial zone. By November, water had disappeared from the lumina of current-year earlywood vessels, and water reappeared in the lumina of earlywood fibres around the currentyear earlywood vessels. Our results indicate that cavitation in lumina of current-year earlywood vessels occurred during the period from October to November.