Early Stages Of Exposure Research Articles

Effect of Temperature on the Corrosion Behavior of Biodegradable AZ31B Magnesium Alloy in Ringer’s Physiological Solution

In this work, the corrosion behaviors of the AZ31B alloy in Ringer’s solution at 20 °C and 37 °C were compared over four days to better understand the influence of temperature and immersion time on corrosion rate. The corrosion products on the surfaces of the AZ31B alloys were examined by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD). Electrochemical impedance spectroscopy (EIS) provided information about the protective properties of the corrosion layers. A significant acceleration in corrosion rate with increasing temperature was measured using mass loss and evolved hydrogen methods. This temperature effect was directly related to the changes in chemical composition and thickness of the Al-rich corrosion layer formed on the surface of the AZ31B alloy. At 20 °C, the presence of a thick (micrometer scale) Al-rich corrosion layer on the surface reduced the corrosion rate in Ringer’s solution over time. At 37 °C, the incorporation of additional Mg and Al compounds containing Cl into the Al-rich corrosion layer was observed in the early stages of exposure to Ringer’s solution. At 37 °C, a significant decrease in the thickness of this corrosion layer was noted after four days.

The dynamic changes of arsenic bioaccumulation and antioxidant responses in the marine medaka Oryzias melastigma during chronic exposure

Arsenic (As) is a highly toxic metalloid to aquatic organisms, but the effects of low-dose chronic inorganic As exposure on marine fish are still unclear. A 28-day study was conducted on chronic exposure of 100 μg/L inorganic As [As(III) and As(V)] in the marine medaka Oryzias melastigma to quantify the effects of chronic inorganic As exposure on its bioaccumulation, biotransformation, oxidative stress, and antioxidant enzymes response. During the exposure period, chronic inorganic As exposure had no significant effect on the total As bioaccumulation except at 7 d for As(V) treatment. Based on the toxicokinetic data, the low As bioaccumulation was caused by low dissolved uptake (ku), internal transfer (k12, k21) and high efflux (ke1). The organic As were the predominated species (77 − 80%) and remained constant, while the inorganic As increased 35% (from 0.26 μg/g to 0.35 μg/g) during the initial 4-d exposure and then recovered. The increased inorganic As could be covered by the high contribution of organic As especially arsenobetaine (AsB) to the total As accumulation. Coincidently, the malondialdehyde (MDA) levels followed similar trends as the inorganic As concentrations, indicating that inorganic As bioaccumulation induced oxidative stress at the initial stage. Both the contents of the nonenzymatic antioxidant (glutathione, GSH) and the activities of the enzymatic antioxidants (superoxide dismutase (SOD), catalase (CAT), peroxidase (POD) and glutathione-S-transferase (GST)) increased initially and then decreased as the inorganic As concentrations, thus lowering the hydrogen peroxide (H2O2) levels and displaying a typical antioxidant defense mechanism. In summary, this study elucidated that although the marine medaka had a limited ability to accumulate waterborne As, the increase in the inorganic As at the early stage of exposure still caused toxic effects, which could be ignored by constant total As concentrations. Therefore, the toxicity of As could be underestimated if only the total As instead of the inorganic As is monitored in marine fish.

Comparison on the Aging of Woods Exposed to Natural Sunlight and Artificial Xenon Light.

To investigate the relationship between sunlight and artificial light sources on the weathering of wood, three woods, namely, Tectona grandis L.F. (teak), Stereospermum colais (mabberley), and Dicorynia guianensis (basralocus), were tested under natural sunlight for 733 days and artificial xenon light for 180 h, respectively. A comparison between sunlight and artificial xenon light was made based on surface color changes at various intervals. The results showed that the woods suffered from more severe aging in the artificial xenon light exposure than that in the natural sunlight exposure. At the early stage of exposure, very good relationships were found between 70 days under natural sunlight weathering and 60 h under artificial xenon light weathering. Compared with natural sunlight, about a 30 times faster aging process was identified in the artificial xenon light. However, the linear relationship vanished at the later aging stage. It was found that the color change fluctuated in natural sunlight, while it increased steadily in artificial xenon light. The wood species affected the aging of woods. In natural sunlight exposure, the color change decreased in the order of mabberley > teak > basralocus, while in artificial xenon light exposure, color change decreased in the order of mabberley > basralocus > teak due to the easier volatilization of extractives in artificial xenon light than in natural sunlight.

1,4-Dioxane exposure induces kidney damage in mice by perturbing specific renal metabolic pathways: An integrated omics insight into the underlying mechanisms

1,4-Dioxane (dioxane), an industrial solvent widely detected in environmental and biological matrices, has potential nephrotoxicity. However, the underlying mechanism by which dioxane induces kidney damage remains unclear. In this study, we used an integrated approach, combining kidney transcriptomics and urine metabolomics, to explore the mechanism for the toxic effects of dioxane on the mouse kidney. Transcriptomics profiling showed that exposure to 0.5 mg/L dioxane induced perturbations of multiple signaling pathways in kidneys, such as MAPK and Wnt, although no changes in oxidative stress indicators or anatomical pathology were observed. Exposure to 500 mg/L dioxane significantly disrupted various metabolic pathways, concomitantly with observed renal tissue damage and stimulated oxidant defense system. Urine metabolomic analysis using NMR indicated that exposure to dioxane gradually altered the metabolic profile of urine. Within the full range of altered metabolites, the metabolic pathway containing glycine, serine and threonine was the most significantly altered pathway at the early stage of exposure (3 weeks) in both 0.5 and 500 mg/L dioxane-treated groups. However, with prolonged exposure (9 and 12 weeks), the level of taurine significantly decreased after treatment of 0.5 mg/L dioxane, while exposure to 500 mg/L dioxane significantly increased glutathione levels in urine and decreased arginine metabolism. Furthermore, integrated omics analysis showed that 500 mg/L dioxane exposure induced arginine deficiency by perturbing several genes involved in renal arginine metabolism. Shortage of arginine coupled with increased oxidative stress could lead to renal dysfunction. These findings offer novel insights into the toxicity of dioxane.

Relationship between Mg, B and Mn status and tomato tolerance against Cd toxicity

Distinct tomato genotypes possess different tolerance degree to cadmium (Cd), but the mechanisms behind this phenomenon are scarcely understood. To this end, the physiological, biochemical, anatomical, nutritional and molecular mechanisms associated to the plant tolerance against Cd toxicity were investigated in five tomato accessions with contrasting sensitivity to Cd exposure. Firstly, the data revealed that larger biomass loss was not always coupled to higher Cd concentration, indicating that other events, in addition to the internal Cd accumulation, impact tomato performance at early stages of Cd exposure. Secondly, the results indicated that the fine regulation of nutrient status, particularly magnesium (Mg), boron (B) and manganese (Mn), is associated to the mitigation of Cd toxicity. Magnesium status was coupled to the modulation of root development, resulting in changes in root hair formation and biomass allocation. Boron accumulation in leaves was linked to Cd toxicity, suggesting that tolerance mechanisms involved strategies to decrease or even avoid B excess in photosynthetic tissues. Disturbances in Mn status, i.e. Mn excess in leaves and Mn deficiency in roots, were also related to tomato sensitivity to Cd exposure. Thirdly, plant capacity to maintain leaf blade expansion is a relevant strategy for a better tomato development after short-term Cd exposure. Fourthly, tomato tolerance to Cd-induced stress does not depend on CAT activity enhancements in such conditions. In conclusion, tomato ability to quickly manage its nutritional status is necessary for alleviation of the Cd effects at early stages of exposure to this metal. The better understanding about tolerance mechanisms and mode of action of Cd toxicity in plants can help in the establishment of strategies to mitigate its impacts on crops.

Assessment of the Live Attenuated and Wild-Type Edwardsiella ictaluri-Induced Immune Gene Expression and Langerhans-Like Cell Profiles in the Immune-Related Organs of Catfish.

Edwardsiella ictaluri is a Gram-negative intracellular pathogen that causes enteric septicemia of catfish (ESC). Successful vaccination against intracellular pathogens requires T cell priming by antigen presenting cells (APCs) that bridge innate and adaptive immunity. However, the evidence on immunological mechanisms that underscore E. ictaluri pathogenesis and the protective role of live attenuated vaccines (LAVs) is scarce. We assessed the expression of immune genes related to antigen presentation by real-time PCR and the distribution patterns of Langerhans-like (L/CD207+) cells by immunohistochemistry in the immune-related tissues of channel catfish challenged with two novel E. ictaluri LAVs, EiΔevpB, and ESC-NDKL1 and wild type (WT) strain. Our results indicated significantly elevated expression of IFN-γ gene in the anterior kidney (AK) and spleen of vaccinated catfish at the early stages of exposure, which correlated with increased numbers of L/CD207+ cells. In general, the ESC-NDKL1-induced IFN-γ gene expression patterns in the AK resembled that of the patterns induced by EiΔevpB. However the MHCII gene expression patterns differed between the strains with significant increases at 6 h post-challenge (pc) with the EiΔevpB and at 7 d pc with the ESC-NDKL1 strains, respectively. Significant increases in activity of T helper type polarization genes such as IFN-γ and T cell co-receptors after exposure to ESC-NDKL1, in combination with elevated numbers of L/CD207+ cells at 7 d pc with both LAVs compared to uninfected and the WT-exposed counterparts, were documented in the spleen. The dominant pro-inflammatory environment with dramatically overexpressed inflammatory genes in the AK and 7 d pc in the spleen in response to E. ictaluri was found in exposed catfish. In general, the pro-inflammatory gene expression profiles in the ESC-NDKL1 pc showed more similarities to the WT strain-induced gene profiles compared to the EiΔevpB counterpart. In addition, E. ictaluri WT significantly decreased the numbers of Langerhans-like L/CD207+ cells in the AK and spleen at 3 and 7 days pc. In conclusion, we report the differential framework of initiation of innate and adaptive immune responses between E. ictaluri strains with both LAVs having a potential of satisfying the stringent requirements for successful vaccines.

Durability of composite assemblies under extreme conditions: Thermomechanical damage prediction of a double-lap bonded composite assembly subject to impact and high temperature

The objective of this study is to simulate and predict the thermomechanical damage of composite material assemblies subjected to impact load while in a high temperature environment. Three-dimensional models were developed for a glass-fiber reinforced vinyl ester double-lap bonded composite assembly subject to combined mechanical and high thermal loads. Both thermal and mechanical models were implemented in the finite element analysis software Abaqus, using sequential heat transfer and dynamic implicit simulations. The thermal model is customized to properly simulate the thermal behavior of composites and generate accurate results while the mechanical model uses the existing functions of Abaqus. For a double-lap composite assembly, thermomechanical failure is predicted in the adhesive zone, at the adherent/adhesive interface, as the adhesive deteriorates at the early stages of exposure. The adherent also deteriorates but at a slower rate. Furthermore, stress concentration is observed at the edges of the stress distribution along the adhesive length, while the average stress along the length decreases gradually as a function of the fire exposure time. The conducted simulations made it possible to predict the stress distribution field variation as a function of time in the double-lap bonded assembly under a combined thermal-impact load. This would serve as a valuable tool for composite structure designers in sizing bonded composite assemblies for their structural projects, as the specifications for certain structures impose a time of evacuation of the structure during a shock and triggering of a fire.

Toxicity of silver nanoparticles to green algae M. aeruginosa and alleviation by organic matter.

Silver nanoparticles (AgNPs) have been increasingly used in a wide range of consumer products over the last decade. The release of AgNPs into aquatic ecosystems raises concerns about their safety and environmental toxicity, which have been the subject of recent studies. Herein, we assess the toxicity of AgNPs to the common algae Microcystis. aeruginosa. A toxicological response by M. aeruginosa was exhibited at an early stage of exposure to AgNPs, which were also toxic to its growth, photosynthetic, and membrane systems. The attachment of AgNPs to microalgae is likely the main mechanism by which it damages cell membranes. Dissolved Ag ions, originating from internalized AgNPs, seem to directly target the photosynthetic system. We also found that several humus-related indicators of water quality (HIX and β/α) were related to reduced AgNPs toxicity. Graphical abstract.

The tendency of linuron in microcosmic system and its response to hydrodynamic conditions

The environmental fate and bioaccumulation of linuron in a laboratory microcosm were investigated at three flow velocity over a period of 10 days. Linuron concentrations were quantified in the environmental media water, sediment, algae and fish after 1, 2, 4, 7 and 10 days of exposure. The results showed that rapid decrease in water phase of the microcosm was occurred, linuron had decreased to 56.7%-67.9% of the initial concentrations on day 10, and reduction rates showed an obvious increase with increased flow velocity. The linuron concentrations in the sediment were 1.25-2.13 ng/g on day 10, which were much less than that in algae (387-477 ng/g). The linuron was widely detected in fish tissues, and the bioaccumulation concentrations were generally in the following order: liver > kidney > brain > skin > muscle > gill at an early stage of exposure. However, the ability of liver detoxification increased with the exposure time and exposure flow velocity, so that the bioaccumulation potential was highest in kidney at the end stage of exposure. This result indicates that a significant uptake potential of linuron in organisms, further studies are necessary to elucidate food chain bioaccumulation and toxicological effects of linuron.

Reinforcement corrosion research based on the linear polarization resistance method for coral aggregate seawater concrete in a marine environment

PurposeThis paper aims to reduce the cost, limit the time and increase raw material source availability, coral aggregate seawater concrete (CASC) composed of coral, coral sand, seawater and cement can be widely used for the construction of ports, levees, airports and roads to achieve practical engineering values. However, the naturally porous coral structure and abundant Cl− in the seawater and coral lead to extremely severe reinforcement corrosion for CASC. It is well known that Cl− is the main cause of reinforcement corrosion in the marine environment. Therefore, it is necessary to research the reinforcement corrosion of CASC in the marine environment.Design/methodology/approachIn this study, linear polarization resistance was adopted to test the linear polarization curves of reinforcement in CASC with different exposure times. Ecorr, Rp, Icorr and Vcorr were calculated according to the weak electrochemical polarization theory and Stern–Geary formula. The effects of concrete cover thickness, exposure time, reinforcement types and inhibitor on reinforcement corrosion in CASC were analysed. The reinforcement corrosion degradation rule was determined, which provided theoretical support for the durability improvement, security assessment, service life prediction and service quality control of CASC structures in marine islands and reef engineering.FindingsThe corrosion resistance was enhanced with increased concrete cover thickness, and the concrete cover thickness for organic new coated steel should be at least 5.5 cm to reduce the reinforcement corrosion risks in CASC structures. The corrosion resistance of different types of reinforcements followed the rule: 2205 duplex stainless steel > 316 stainless steel > organic new coated steel > zinc-chromium coated steel > common steel. In the early exposure stage, the anti-corrosion effectiveness of the calcium nitrate inhibitor (CN) was superior to that for the amino alcohol inhibitor (AA). With the extension of exposure time, the decreasing rate of anticorrosion effectiveness of CN was higher than that of AA.Originality/valueReinforcement corrosion of CASC in a marine environment was studied. Concrete cover thickness, exposure time, reinforcement type and inhibitor influenced the reinforcement corrosion were investigated. New technique of reinforcement anti-corrosion in marine engineering was proposed. Possible applications of CASC in marine engineering structures were suggested.

Effect of Cefotaxime on the CAT Activities and GSH Contents of Zebrafish

In order to define eco-toxicity effect of cefotaxime on zebrafish, the indoor exposure method was used to study the impact of cefotaxime on zebrafish. In this study, zebrafish was exposed to cefotaxime of 1mg/L, 5mg/L, 25mg/L and 125mg/L for 15 days to study the effect of Catalase (CAT) activities and Glutathione (GSH) contents. According to the experimental data, the CAT activities and GSH contents in zebrafish muscle tissue had changed significantly during the period of exposure. The experimental results show that the activities of CAT in four concentration groups were significantly inhibited (P<0.01). The CAT activities in the 1 mg/L and 5 mg/L groups showed the "Λ" type change, inhibited first and induced later. But in the 25 mg/L and 125 mg/L groups, the CAT activities were inhibited all the time. Cefotaxime had a significant effect on GSH content in the muscle tissue of the zebrafish at the early stage of exposure, rapidly increase to the maximum at the early stage and rapidly decrease to the minimum on the 6th day. During 6th day to 15th day, the contents of GSH in the zebrafish were basically stable at the level of control. The experimental results show that the CAT activities and GSH contents in zebrafish muscle tissue had changed significantly.

Effect of ammonium and high light intensity on the accumulation of lipids in Nannochloropsis oceanica (CCAP 849/10) and Phaeodactylum tricornutum (CCAP 1055/1)

BackgroundMicroalgae accumulate lipids when exposed to stressful conditions such as nutrient limitation that can be used to generate biofuels. Nitrogen limitation or deprivation is a strategy widely employed to elicit this response. However, this strategy is associated with a reduction in the microalgal growth, leading to overall poor lipid productivities. Here, we investigated the combined effect of a reduced source of nitrogen (ammonium) and super-saturating light intensities on the growth and induction of lipid accumulation in two model but diverse microalgal species, Phaeodactylum tricornutum and Nannochloropsis oceanica. We hypothesized that the lower energy cost of assimilating ammonium would allow the organisms to use more reductant power for lipid biosynthesis without compromising growth and that this would be further stimulated by the effect of high light (1000 µmol m−2 s−1) stress. We studied the changes in growth and physiology of both species when grown in culture media that either contained nitrate or ammonium as the nitrogen source, and an additional medium that contained ammonium with tungsten in place of molybdenum and compared this with growth in media without nitrogen. We focused our investigation on the early stages of exposure to the treatments to correspond to events relevant to induction of lipid accumulation in these two species.ResultsAt super-saturating light intensities, lipid productivity in P. tricornutum increased twofold when grown in ammonium compared to nitrogen free medium that increased further when tungsten was present in the medium in place of molybdenum. Conversely, N. oceanica growth and physiology was not compromised by the high light intensities used, and the use of ammonium had a negative effect on the lipid productivity, which was even more marked when tungsten was present.ConclusionsWhilst the use of ammonium and super-saturating light intensities in P. tricornutum was revealed to be a good strategy for increasing lipid biosynthesis, no changes in the lipid productivity of N. oceanica were observed, under these conditions. Both results provide relevant direction for the better design of processes to produce biofuels in microalgae by manipulating growth conditions without the need to subject them to genetic engineering manipulation.

Discovery and theoretical and technical innovations of Yuanba gas field in Sichuan Basin, SW China

Abstract To solve the difficulties in exploration and development in Yuanba ultra-deep gas field in Sichuan Basin, SW China, the article studies the mechanism of quality reef reservoirs development and gas accumulation and innovates techniques in ultra-deep seismic exploration, drilling, completion and testing. Through the reconstruction of dynamic depositional evolution process and regional depositional framework of homoclinal ramp-rimmed platform in Upper Permian, three theories are put forward: first, “early beach-late reef, multiple stacking, arrangement in rows and belts” is the sedimentary mode for the reservoirs in the Changxing Formation of Yuanba area; second, “dissolution in early exposure stage and dolomitization during shallow burial giving rise to the pores in matrix, overpressure caused by cracking of liquid hydrocarbon during deep burial inducing fractures” is the reservoirs development mechanisms; third, “coupling of pores and fractures” controls the development of high quality reservoirs in deep formations. From correlation of oil and source rock, it is concluded that the Wujiaping Formation and Dalong Formation of deep-water continental shelf are the major source rocks in the Permian of northern Sichuan Basin. The hydrocarbon accumulation mode in ultra-deep formations of low-deformation zones is characterized by “three-micro (micro-fault, micro-fracture interbed crack) migration, near-source enrichment, and persistent preservation”. Through seismic inversion using the pore structure parameters of pore-fracture diadactic structure model, the high production gas enrichment area in Yuanba gas field is 98.5 km2. Moreover, special well structure and unconventional well structure were used to deal with multiple pressure systems and sealing of complex formations. A kind of integral, high pressure resistant FF-level gas wellhead and ground safety linkage device was developed to accomplish safe and environmentally friendly gas production.

Analysis of the effects of chemical ageing of ethylene-propylene diene monomer by chemical, spectroscopic, and thermal means

Ethylene-propylene diene monomer (EPDM) failures due to material degradation poses a major risk in the biopharmaceutical industry, which can result in long periods of production downtime. It is suspected that a key cause of this EPDM degradation is due to the chemical solutions used in equipment cleaning processes, resulting in crosslinking of the EPDM polymer bulk. However, the mechanisms responsible for crosslink formation, and whether other degradation sources are also present, has never been investigated in the public domain. Twenty four virgin samples were utilised for testing, twelve of which were subject to common chemical cleaning solutions used in the biopharmaceutical sector. The chemical solutions under investigation were aqueous solutions of NaOH, NaClO, H3PO4, and the interaction between 100 °C H2O and NaClO. The characterisation of the degradation process was conducted via chemical, spectroscopic and thermal means. The results show that degradation of the polymer bulk proceeds predominantly via crosslinking for all exposure types, due to oxidative damage and the formation and recombination of free radicals. Loss of plasticiser in the polymer matrix and thermo-oxidative damage are contributory degradation mechanisms. NaOH and H3PO4 exposure results in an accelerated rate of crosslinking compared to NaClO in the early stages of exposure.

Chemical ageing effects on the mechanical behaviour of ethylene-propylene diene monomer

Ethylene-propylene diene monomer (EPDM) elastomer diaphragm failures due to material degradation pose a major risk in the biopharmaceutical industry, as they can result in long periods of production downtime. It is suspected that a key cause of this EPDM degradation is due to the chemical solutions used in equipment cleaning processes. However this has never been empirically investigated in the public domain. Twenty four virgin samples were utilised for testing, twelve of which were subject to common chemical cleaning solutions used in the biopharmaceutical sector. The chemical solutions under investigation were aqueous solutions of NaOH, NaClO, H3PO4, and the interaction between 100 °C H2O and NaClO. The characterisation of the degradation process was conducted by mechanical testing. The results show that degradation of the polymer bulk proceeds predominantly via crosslinking for all exposure types. NaOH and H3PO4 exposure results in an accelerated rate of crosslinking compared to NaClO in the early stages of exposure.

Corrosion Behavior of High and Low Temperature Austempered Ductile Iron (ADI) in Iron Ore Slurry

Abstract Corrosion behavior of austempered ductile iron (ADI) and forged EN31 steel balls in a ground iron ore slurry was studied as a function of time in the slurry, while the microstructure of ADI developed due to different tempering temperature and tempering time. The corrosion rates of the grinding balls immersed in the iron ore slurry were determined using electrochemical analysis and weight loss methods. It was found that the pH of the iron ore slurry increased with time and the corrosion behavior was influenced by the pH of the slurry. The corrosion rate of forged EN31 steel balls increased with the increase in time and pH of the slurry, whereas the corrosion rate of ADI balls depended on the austempering treatment. In general, the forged EN31 steel ball offered better corrosion resistance than ADIs during the early stages of exposure in the slurry (low pH values of the slurry), but at higher pH values of the slurry, the ADIs yielded better corrosion resistance than forged EN31 steel balls. The ADI austempered at higher temperatures showed better corrosion resistance than the ones austempered at lower temperatures.

Effect of Thermal Annealing on Machining-Induced Residual Stresses in Inconel 718

Nickel-based alloys are widely employed in the manufacturing of aero-engines. These alloys are difficult to machine, and tensile residual stresses are generated during machining. These tensile residual stresses can negatively affect the performance of aero-engine components. Nevertheless, residual stresses can vary due to thermal or mechanical loading. These variations must be considered to evaluate the real influence of residual stresses on component behavior. This paper studies the effect of thermal loads on machining-induced residual stresses in the alloy Inconel 718. A ring-shaped Inconel 718 part was face-turned, and specimens were extracted from it. Specimens were exposed at 550 and 650 °C for 10 min, 1 and 10 h. Residual stresses were measured, and microstructure was observed before and after thermal exposure. Residual stress variations found after thermal exposure were the consequence of two factors: relaxation of strain bands during the early stage of exposure and diffusion-controlled creep. In addition, a modified Zener-Wert-Avrami model is proposed to predict residual stress relaxation caused by the diffusion-controlled creep. Once having fitted the modified Zener-Wert-Avrami model, the study was extended for a wider range of temperatures (400-650 °C). This analysis showed that surface residual stresses do not relax significantly at temperatures below 500 °C.

Phytoextraction of Pb, Cr, Ni, and Zn using the aquatic plant Limnobium laevigatum and its potential use in the treatment of wastewater.

In order to study the bioaccumulation of Pb, Cr, Ni, and Zn and the stress response, the floating aquatic plant Limnobium laevigatum was exposed to increasing concentrations of a mixture of these metals for 28days, and its potential use in the treatment of wastewater was evaluated. The metal concentrations of the treatment 1 (T1) were Pb 1μgL-1, Cr 4μgL-1, Ni 25μgL-1, and Zn 30μgL-1; of treatment 2 (T2) were Pb 70μgL-1, Cr 70μgL-1, Ni 70μgL-1, and Zn 70μgL-1; and of treatment 3 (T3) were Pb 1000μgL-1, Cr 1000μgL-1, Ni 500μgL-1, and Zn 100μgL-1, and there was also a control group (without added metal). The accumulation of Pb, Cr, Ni, and Zn in roots was higher than in leaves of L. laevigatum, and the bioconcentration factor revealed that the concentrations of Ni and Zn in the leaf and root exceeded by over a thousand times the concentrations of those in the culture medium (2000 in leaf and 6800 in root for Ni; 3300 in leaf and 11,500 in root for Zn). Thus, this species can be considered as a hyperaccumulator of these metals. In general, the changes observed in the morphological and physiological parameters and the formation of products of lipid peroxidation of membranes during the exposure to moderate concentrations (T2) of the mixture of metals did not cause harmful effects to the survival of the species within the first 14days of exposure. Taking into account the accumulation capacity and tolerance to heavy metals, L. laevigatum is suitable for phytoremediation in aquatic environments contaminated with moderated concentrations of Cr, Ni, Pb, and Zn in the early stages of exposure.

Inlfuence of early sulfate exposure on the pore network development of mortars

The objective of this paper is to evaluate the influence of sulfate exposure on the pore network development of several Portland cement matrices. MIP, XRD and SEM analysis were performed at different ages in samples exposed to sulfates after 2days of casting. Results suggest that patterns of precipitation of the expansive products are linked to the degree of refinement of the pore network. During early stages of exposure, large pores concentrate a higher proportion of the expansive product formed. At later stages, precipitation evolves towards finer pore sizes.

Germination, Physiological Responses and Gene Expression of Tall Fescue (Festuca arundinacea Schreb.) Growing under Pb and Cd.

Cadmium (Cd) and lead (Pb) are recognized as the most toxic metal ions due to their detrimental effects not only to plants, but also to humans. The objective of this study was to investigate the effects of Cd and Pb treatments on seed germination, plant growth, and physiological response in tall fescue (Festuca arundinacea Schreb.). We employed six treatments: CK (nutrient solution as control), T1 (1000 mg L-1 Pb), T2 (50 mg L-1 Cd), T3 (150 mg L-1 Cd), T4 (1000 mg L-1 Pb+50 mg L-1 Cd), T5 (1000 mg L-1 Pb+150 mg L-1 Cd). Antagonistic and synergistic actions were observed in tall fescue under Pb and Cd combined treatments. Under low Cd, plants exhibited higher relative germination rate, germ length, VSGR, catalase (CAT) and peroxidase (POD) activities. Additionally, in the shoots, the gene expression level of Cu/Zn SOD, FeSOD, POD, GPX, translocation factors, MDA, EL, and soluble protein contents were reduced under Pb stress. Conversely, under high Cd level, there was a decline in NRT, Pb content in shoots, Pb translocation factors, CAT activity; and an increase in VSGR, Pb content in roots, gene expression level of Cu/ZnSOD and POD in tall fescue exposed to Pb2+ regimes. On the other hand, tall fescue plants treated with low Cd exhibited lower relative germination rate, germination index, germ length, NRT, Cd content in roots. On the other hand there was higher Cd content, Cd translocation factor, CAT and POD activities, and gene expression level of Cu/Zn SOD, FeSOD, POD, GPX under Pb treatment compared with single Cd2+ treatment in the shoots. However, after high Cd exposure, plants displayed lower NRT, Cd content, CAT activity, and exhibited higher Cd contents, Cd translocation factor, MDA content, gene expression level of Cu/ZnSOD and GPX with the presence of Pb2+ relative to single Cd2+ treatment. These findings lead to a conclusion that the presence of low Cd level impacted positively towards tall fescue growth under Pb stress, while high level of Cd impacted negatively. In summary, antioxidant enzymes responded to Cd and Pb interaction at an early stage of exposure, and their gene expression profiles provided more details of the activation of those systems.