Dynamic Test Method Research Articles

Analysis of Corrosion Causes and Optimization of Corrosion Evaluation Methods for Water Injection System in Changqing JY Oilfield

Abstract Based on the corrosion characteristics of the water injection system in Changqing Oilfield, an experimental study was conducted on the corrosion of the water injection system caused by carbon dioxide, hydrogen sulfide, bacteria, and water treatment agents in the produced liquid. The main influencing factors of corrosion in the water injection system were analyzed, and it was clarified that the corrosion of the water injection system in Changqing Oilfield was mainly caused by oxygen corrosion, which also had an impact on the water quality of the injection. Combining static corrosion analysis with the introduction of pitting and dynamic corrosion rate testing methods, the average corrosion rate of JY oilfield water injection system has a positive correlation with pitting corrosion, while the average corrosion rate of clean water has a stronger correlation with pitting corrosion. The corrosion evaluation method has been optimized, providing technical basis for formulating effective anti-corrosion measures for the oilfield.

Rigidity coefficients of rubber belts for dynamic testing of modulus of elasticity and shear modulus of non-wood engineered board

To determine the appropriate stiffness coefficient k values for rubber belts used in dynamic testing of the elastic modulus and shear modulus of timber and solid wood composite materials, this study employed three different thicknesses of rubber belts. Dynamic tests were conducted on straw boards, Laminated Veneer Lumber (LVL), and Spruce-Pine-Fir (SPF) materials, and the results were validated and analyzed using static four-point bending tests. The conclusions drawn from this research indicate that the range of stiffness coefficient k values for the rubber belts obtained through dynamic testing fell between 0.05 and 0.28 N/m. The correctness of the dynamic testing method was verified through static four-point bending tests. The error levels for elastic modulus E and shear modulus G of the same type of board measured using the three different rubber belts were below 9.5% and 9.8%, respectively.

Can isometric testing substitute for the one repetition maximum squat test?

When measuring maximum strength, a high accuracy and precision is required to monitor the training adaptations. Based on available reliability parameters, the literature suggests the replacement of the one repetition maximum (1RM) by isometric testing to save testing time. However, from a statistical point of view, correlation coefficients do not provide the required information when aiming to replace one test by another. Therefore, the literature suggests the inclusion of the mean absolute error (MAE), the mean absolute percentage error (MAPE) for agreement analysis. Consequently, to check the replaceability of 1RM testing methods, the current study examined the agreement of isometric and dynamic testing methods in the squat and the isometric mid-thigh pull. While in accordance with the literature, correlations were classified high r = 0.638-0.828 and ICC = 0.630-0.828, the agreement analysis provided MAEs of 175.75-444.17 N and MAPEs of 16.16-57.71% indicating an intolerable high measurement error between isometric and dynamic testing conditions in the squat and isometric mid-thigh pull. In contrast to previous studies, using MAE, MAPE supplemented by CCC and BA analysis highlights the poor agreement between the included strength tests. The recommendation to replace 1RM testing with isometric testing routines in the squat does not provide suitable concordance and is not recommended.

Surface defect visualisation using scanning electromagnetic induction thermography

ABSTRACT Scanning electromagnetic induction thermography (SEIT) has great potential for industrial applications, such as rapid visualising of surface cracks. This dynamic non-destructive testing method has improved detection efficiency but has led to blurred or discontinuous defect boundaries at varying scanning speeds. To alleviate this problem, we explore the use of the patch-based sparse decomposition (PSD) technique. This technique improves dynamic imaging by retaining only the information associated with sparse regression and introducing a locally adaptive threshold. Besides, this method offers a potential thermal image preconditioned scheme for follow-up artificial intelligence detection. Experimental results show that PSD can correct blurred images caused by relative motion, thus improving defect detection accuracy. Moreover, it is suitable for both translational and rotational detection systems. Images reconstructed through the deblurring process demonstrate the ability to visualise holes with a radius of 0.5 mm at velocities up to 150 mm/s, while cracks with a defect width of 0.2 mm on a railroad wheel can be detected at speeds ranging from 25 mm/s to 75 mm/s.

Testing of wood shear modulus based on cantilevered square plate torsional vibration method

ABSTRACT The application of the energy method has proposed a dynamic testing method for the shear modulus in two mutually perpendicular directions on the principal surface of wood using a cantilevered square plate torsional vibration method. In the study, this method was applied to measure the shear modulus of larch wood in the LT and TL directions, as well as the longitudinal and transverse shear modulus of Laminated Veneer Lumber (LVL) sheets. The validity of the results was confirmed through experimental verification using the asymmetric four-point bending beam method, the free plate torsional vibration method, and the free square plate torsional mode method. Simulation calculations of the principal shear modulus for six species of trees with width-to-thickness ratios ranging from 10 to 25 were also conducted using this method. The conclusions drawn suggest that a width-to-thickness ratio of 15 for the cantilevered square plate provides sufficient accuracy for testing the principal shear modulus of wood. Furthermore, the difference in shear modulus between two mutually perpendicular directions on the principal surface of wood is dependent on the width-to-thickness ratio of the cantilevered square plate, indicating that this method outperforms other dynamic methods for testing wood shear modulus.

Dynamic swatch testing of liquid aerosols in a laboratory-sized recirculating wind tunnel

Chemical warfare agents (CWAs) pose a threat as gaseous substances and as liquid aerosols, necessitating chemical warfare-protective clothing for soldiers. The paramount consideration lies in the effectiveness of the clothing as a barrier against the pertinent CWAs. This paper presents a dynamic swatch test method aimed at evaluating the performance of such clothing against liquid-phase aerosol penetration. Central to the methodology is a specialized test cell designed to rotate to the left and right, integrated within a laboratory wind tunnel, replicating mission-relevant conditions with varying wind speeds. Utilizing di(2-ethylhexyl) sebacate particles as liquid aerosols, tests were conducted at wind speeds of 1.0, 3.0, and 5.0 m/s. Penetration assessment relied on analyzing particle counts downstream and upstream of the fabric, with preliminary studies showing that higher wind speeds and fabric air permeabilities increase penetration at an equivalent face velocity of 5.0 cm/s. Interestingly, penetration decreased when fabric samples were subjected to rotation. The system and methodology devised demonstrated consistent and repeatable results, offering valuable insights into optimizing the effectiveness of chemical warfare-protective clothing. This research contributes to advancing methodologies for testing protective clothing, crucial for ensuring the safety of military personnel in hazardous environments.

Stability and accuracy of central difference method for real-time dynamic substructure testing considering mass participation coefficient

Stability and accuracy of central difference method for real-time dynamic substructure testing considering mass participation coefficient

Bearing Capacity of Precast Concrete Joint Micropile Foundations in Embedded Layers: Predictions from Dynamic and Static Load Tests according to ASTM Standards

In this paper, joint precast piles with a cross-section of 400 × 400 mm and a pin-joined connection were considered, and their interaction with the soil of Western Kazakhstan has been analyzed. The following methods were used: assessment of the bearing capacity using the static compression load test (SCLT by ASTM) method, interpretation of the field test data, and the dynamic loading test (DLT) method for driving precast concrete joint piles, including Pile Driving Analyzer (PDA by ASTM) and Control and Provisioning of Wireless Access Points (CAPWAP) methods. According to the results, the composite piles tested by the PDA (by ASTM) method differ by 15 percent compared to the static load method, while the difference between the dynamic DLT (by ASTM) method and the static load (by ASTM) method was only 7 percent. So, according to the results, the alternative dynamic method DLT (by ASTM) is very effective and more accurate compared to other existing methods.

Quaternion-Based Attitude Estimation of an Aircraft Model Using Computer Vision.

Investigating aircraft flight dynamics often requires dynamic wind tunnel testing. This paper proposes a non-contact, off-board instrumentation method using vision-based techniques. The method utilises a sequential process of Harris corner detection, Kanade-Lucas-Tomasi tracking, and quaternions to identify the Euler angles from a pair of cameras, one with a side view and the other with a top view. The method validation involves simulating a 3D CAD model for rotational motion with a single degree-of-freedom. The numerical analysis quantifies the results, while the proposed approach is analysed analytically. This approach results in a 45.41% enhancement in accuracy over an earlier direction cosine matrix method. Specifically, the quaternion-based method achieves root mean square errors of 0.0101 rad/s, 0.0361 rad/s, and 0.0036 rad/s for the dynamic measurements of roll rate, pitch rate, and yaw rate, respectively. Notably, the method exhibits a 98.08% accuracy for the pitch rate. These results highlight the performance of quaternion-based attitude estimation in dynamic wind tunnel testing. Furthermore, an extended Kalman filter is applied to integrate the generated on-board instrumentation data (inertial measurement unit, potentiometer gimbal) and the results of the proposed vision-based method. The extended Kalman filter state estimation achieves root mean square errors of 0.0090 rad/s, 0.0262 rad/s, and 0.0034 rad/s for the dynamic measurements of roll rate, pitch rate, and yaw rate, respectively. This method exhibits an improved accuracy of 98.61% for the estimation of pitch rate, indicating its higher efficiency over the standalone implementation of the direction cosine method for dynamic wind tunnel testing.

ДИНАМІЧНІ ВИПРОБУВАННЯ МОСТІВ. ЗАГАЛЬНИЙ ОГЛЯД МЕТОДІВ

Introduction. This article deals with the issue of relevance of dynamic testing of bridges in Ukraine, an overview of dynamic testing methods and the prospects for the development of this type of bridge testing. Problem statement. Monitoring the technical condition of bridges is an urgent problem for maintenance services and requires the use of the most advanced methods to quickly identify possible defects and damage in their structures. Dynamic testing is one of such methods, the development and implementation of which requires joint efforts of engineers and the scientific community. Objective. The main purpose of the article is to evaluate and analyze existing approaches to dynamic testing of bridges to diagnose their condition. This study aims to highlight the need to apply these methods to improve the reliability and safety of bridges, as well as to improve strategies for the maintenance and repair of bridge structures. Materials and methods. The material for the article is the experience of performing dynamic tests of bridges in Ukraine, including an example of testing a 420-meter-long reinforced concrete road bridge located in the Western Ukraine. The following research methods were used: analysis of data from scientific sources, analysis of regulatory documents, practical results of using the «Spectrum» software package, mathematical modeling, and general methods of theoretical research.

Relaxation behavior of thin-ply high strain composites using a dynamic mechanical analyzer based column bending test

Deployable space structures made from thin-ply high-strain composite (HSC) laminates can be compactly stowed, but prolonged stowage under high curvature can alter their deployed shape due to relaxation. In this research, a dynamic mechanical analyzer-based column bending test (CBT) method, with a custom-developed fixture was used to characterize the relaxation behavior of thin-ply HSCs. Four laminate configurations were prepared from thin-ply unidirectional IM7/PMT-F7 and Astroquartz/PMT-F7 prepregs: (i) IM7/PMT-F7 [0°], (ii) Astroquartz/PMT-F7 [±45°], (iii) Flexlam [±45°/0°/±45°] and (iv) Flexlam [±45°/90°/±45°]. Surface strains of 0.5, 1.0, 1.5, and 2.0% were sequentially applied to the specimen for 100-min durations, each separated by a 1000-min recovery period. This stepped strain approach was performed at 30°C, 50°C, and 70°C. The relaxation results indicate that the fiber-dominated test configuration, UD IM7/PMT-F7 [0°] lamina, shows no measurable relaxation. However, the matrix-dominated configurations, Astroquartz/PMT-F7 [±45°] lamina and the Flexlam laminates, show measurable relaxation. The Flexlam laminates show less relaxation than the Astroquartz/PMT-F7 [±45°] lamina due to the inclusion of unidirectional IM7 carbon fiber. The result also indicates that the relaxation behavior is time and strain-dependent, not temperature-dependent.

Superior interface adhesion and protective mechanism of room-temperature-curable polymer composite coating on engineering substrates with lower roughness

In view of the technology bottleneck of the adhesion failure of traditional functional protective coatings on the smoother surface of precise parts served in the marine atmosphere, a room-temperature-curable fluoropolymer/polyurethane (denoted as RFP) polymer composite coating of 20–30 μm is prepared on the metal substrates. Static pull-off and dynamic friction test methods are used to evaluate the interface adhesion of the coating. The coating shows superior adhesive strength of 18–24 MPa on a variety of metal substrates with a wide range of surface roughness (Ra = 0.1–1.6 μm). The friction coefficient of the coating surface is about 0.05–0.08, and the wear life is up to 9–12 km/μm. Furthermore, the adhesion strength of the coating remains 12–14 MPa after 1600 h of salt spray while the wear life of the coating keeps 3–9 km/μm after 720 h of salt spray. The influences of surface roughness (Ra), surface free energy (γOxide), surface potential (φOxide) of the metal substrates and the bonding force at substrate-coating interface on the adhesive energy (Eadh.) are discussed, and the mechanism of "physical-chemical-surface" synergetic enhanced interface adhesion is proposed. The RFP coating is used as the intermediate layer for traditional PU and EP coatings to improve their adhesion on smooth aluminum substrate from 1.39 MPa to 17.5 MPa (increased by 1260 %). Thus, the polymer coating has the potential to provide technical support for the development of long-term anticorrosive coating technology for precision components of marine high-tech equipment.

Flexural vibration test method for determining the dynamic elastic modulus of full-size strawboards for use in transportation framed cases

This paper proposes an improvement in the test method for determining the flexural dynamic modulus of elasticity of strawboard with two triangular prisms as supports, for quality control and classification. Free-plate modal and free-plate transient excitation methods were used to test the elastic modulus of 1/4-plate and whole-plate strawboards. The dynamic test results were verified with the four-point bending method and tensile method. The results show that the elastic moduli of strawboards is approximately 2 GPa. The dynamic test method proposed is efficient, simple, repeatable, and accurate. This method is more suitable for factory applications than existing dynamic testing methods. The framed cases produced by the strawboard all meet the performance requirements in GB/T 7284 (2016).

Enhancing Preamplifier Design for Acoustic Emission Detection Instrument

With the development of the industry, the safety of pressure vessels is crucial for both production and personnel safety. The application of acoustic emission testing technology as a dynamic non-destructive testing method in the detection of pressure vessels is becoming increasingly prevalent. This paper presents the design of a low-frequency acoustic emission preamplifier with a frequency range of 30KHz to 200KHz and a gain of 20dB. The preamplifier is composed of amplification circuits, power supply circuits, and filtering components. By utilizing the PXR04 series high-sensitivity resonant acoustic emission sensor and Texas Instruments' OPA333 operational amplifier, along with a clever power supply design, effective signal amplification and system stability are ensured. Experimental results validate the correctness of the design, providing a feasible and effective solution for enhancing the performance of acoustic emission testing equipment.

DETERMINATION OF DYNAMIC PROPERTIES OF 3D PRINTED G3SI1 STEEL

Taylor anvil test is one of the dynamic test method used to determine the dependences of strain rate, strain and temperature on flow stress. This method can be used to determine the stress and strain at any point in the specimen at different temperatures and strain rates. The paper deals with the description of the Taylor anvil test experiment for G3Si1 welding wire. The experiment was carried out in the laboratory of high strain rates at the Faculty of Mechanical Engineering of Brno University of Technology. ANSYS Explicit dynamics software was used to simulate the material behaviour during the test. The Johnson-Cook constitutive relation was used to describe the material behaviour. The simulation results were compared with the experiment.

Bio-Inspired Dark Adaptive Nighttime Object Detection.

Nighttime object detection is challenging due to dim, uneven lighting. The IIHS research conducted in 2022 shows that pedestrian anti-collision systems are less effective at night. Common solutions utilize costly sensors, such as thermal imaging and LiDAR, aiming for highly accurate detection. Conversely, this study employs a low-cost 2D image approach to address the problem by drawing inspiration from biological dark adaptation mechanisms, simulating functions like pupils and photoreceptor cells. Instead of relying on extensive machine learning with day-to-night image conversions, it focuses on image fusion and gamma correction to train deep neural networks for dark adaptation. This research also involves creating a simulated environment ranging from 0 lux to high brightness, testing the limits of object detection, and offering a high dynamic range testing method. Results indicate that the dark adaptation model developed in this study improves the mean average precision (mAP) by 1.5-6% compared to traditional models. Our model is capable of functioning in both twilight and night, showcasing academic novelty. Future developments could include using virtual light in specific image areas or integrating with smart car lighting to enhance detection accuracy, thereby improving safety for pedestrians and drivers.

Prediction of bridge structure deformation and strain based on dynamic testing and intelligent algorithms

The field load test is a direct and effective method for evaluating the performance of bridge structures. However, existing bridge field static load tests are costly and inefficient; moreover, they obstruct traffic and cause unavoidable damage to the bridge structure. As an alternative the the static load test, a random model update method based on bridge dynamic load tests and the Bayesian inference is proposed in this paper. The bridge static load test results were predicted with a high accuracy. To speed up the Bayesian method to infer the posterior probability density of the updated parameters, the Gaussian process was used in place of the finite element model, and the Bayesian inference used the Markov chain Monte Carlo method based on the delayed rejection adaptive Metropolis algorithm. First, the parameters to be modified for the bridge structure analysis model were determined based on the global sensitivity analysis method. Second, a uniform design sampling method was used to establish the Gaussian process optimization model to update the random model of the bridge structure. Finally, a reinforced concrete truss arch bridge was used to verify the correctness of the static load results of the bridge predicted by the random model update method based on dynamic load testing and Bayesian inference. The research results reveal that the prediction results of the bridge static load test based on the dynamic load test and Bayesian inference method agree with the actual test results.

APPLICATION OF VISCOELASTIC SYSTEMS IN OIL PRODUCTION INTENSIFICATION PROCESSES

This paper provides an overview of viscoelastic behavior and the use of viscoelastic fluids (VBLs) in various oil production intensification processes. The first part provides basic models describing viscoelastic behavior and corresponding equations of state. Describes the method of testing under the action of harmonic vibrations (method of dynamic tests), possible options for its implementation and the determined rheological properties of the viscoelastic sample. To interpret the results of dynamic tests, a complex module is most often introduced, which consists of two components — the elastic modulus (G’) and the loss modulus (G’’). These dynamic modules and their relationship describe the behavior of the viscoelastic sample. It is shown that with respect to modules, it is possible to conclude on the type of sample - viscoelastic liquid or viscoelastic body. It is also noted that dynamic tests should be carried out in the area of low amplitudes of oscillating loads, in which the rheological properties do not depend on the applied stress or strain. The second part provides examples of viscoelastic systems used in operations such as water flow isolation, hydraulic fracturing, and modified acid treatments. The most common viscoelastic systems used in various technologies are solutions of surfactants and polymers of different structures. It is noted that in order to obtain a viscoelastic gel, polymer solutions are used with a crosslinker, while the rheological properties of surfactant solutions are controlled by external factors — pH, temperature, water mineralization. Viscoelastic surfactant solutions have an advantage over polymer solutions ‑ they are able to recover their properties after mechanical or thermal exposure due to the formation of supramolecular structures as a result of selforganization of surfactant molecules. The surfactant-based HLT property of reversibly collapsing and recovering is used, in particular, to reduce pressure losses to overcome friction. In flow-deflecting acid compositions, viscoelastic surfactants are mainly used, the most common of which are given in the second part of the article.

Shock-induced energy release reaction characteristics of Nb17Zr33Ti17W33 high entropy alloy

Nb17Zr33Ti17W33 high entropy alloy is a novel class of energetic structural material. In addition to exhibiting insensitivity and mechanical strength commensurate with inert metal materials, it demonstrates the capacity to release non-self-sustained chemical energy under high-speed dynamic load. In this study, the energy release characteristics of the Nb17Zr33Ti17W33 high-entropy alloy material under impact were investigated using the dynamic energy release test method, which involves ballistic gun-induced bullet-target interaction in a quasi-closed reaction vessel. The energy release process and governing laws of the impact event have been meticulously analyzed, resulting in the development of a comprehensive impact compression chemical energy release model. The direct ballistic tests and the recovered products revealed that Nb17Zr33Ti17W33 experienced chemical reactions during the impact loading, primarily the oxidation of the Zr element, which resulted in the release of significant chemical energy. This study elucidates the deformation response mechanism of Nb17Zr33Ti17W33 under high-speed impact loading, providing a crucial reference for further insights and applications of high-entropy alloy materials.

The Effectiveness of determining the Load-bearing Capacity of Piles based on the Results of Pile Dynamic Testing: The Case Study of Long An Province, Vietnam

Determining the load-bearing capacity of piles currently relies on various field experimental methods, with static pile compression loading testing and dynamic pile testing through Pile Driving Analysis (PDA) being widely accepted as reliable practices. However, the application of PDA tests faces limitations, especially in construction projects with weak soil profile while the static pile load test usually requires high testing costs. Consequently, the conventional dynamic pile testing method, checking the resistance through a number of dynamic hammer blows, is commonly utilized. Despite its prevalence, there has been limited research on the traditional dynamic pile testing method. In light of this, the present study aims to examine the traditional approach by analytical and numerical simulations. By doing so, it seeks to offer a more objective and comprehensive understanding of its effectiveness when compared to alternative methods.