Dye Extraction Research Articles

Printing with Natural Dye Extract from Japanese Knotweed Leaves

AbstractInvasive alien plants are detrimentally displacing native plant species and pose a challenge in terms of how their overgrowth can be utilized effectively. In our study, the leaves of one of the world’s worst invasive species, Japanese knotweed, were used to produce a green natural dye. This dye was screen-printed onto various substrates, including cotton and polyester fabrics, commercial cellulose papers, and innovative papers made from the stems of Japanese knotweed. The printed substrates were evaluated using color measurements and fastness properties. The aim of the study was also to investigate the influence of additives in the printing inks, such as sodium carbonate, citric acid, copper and aluminum sulfates, on the color and fastness properties of the prints. The colors of the prints obtained varied, ranging from primarily yellowish-green to brownish-yellow with the addition of citric acid, orange-brown with sodium carbonate, orange-yellow with aluminum sulfate, and brown with copper sulfate. The prints had excellent fastness to dry rubbing and moderate fastness to light. The prints of lower and medium dye concentrations on fabrics had very good fastness to wet rubbing and wet ironing, and on cotton even good fastness to washing. The additives in the printing inks, such as sodium carbonate and metal sulfates, reduced the abrasion resistance of the prints on paper and the wet fastness of the prints on fabrics, but only the metal sulfates had a positive effect on the light fastness of the prints.

In-depth mechanistic insights into Au nanoparticles based polyurethane foams as a selective and efficient dispersive solid phase microextractor for textile dyes from water: performance and reusability study

ABSTRACT Herein, a simple, superhydrophobic, superoleeophilic and low cost microextractor Au nanparticles (Au NPs) based polyurethane (PUFs) solid platform (Au NPs/PUFs) has been developed as a promising sorbent for removal and recovery of Congo red (CR) textile dye from water bodies. The sorbent was characterised using UV-visible and SEM techniques. The procedure relied complete dye retention from the aqueous solution at pH 5.0–5.5 onto an Au NP/PUF extractor. Analytical assessments revealed that the Au NPs/PUFs combination significantly improves mass transfer of dye and enhances creation of active sites for CR retention. CR sorption by the sorbent fitted well with intra-particle diffusion and pseudo first-order kinetic models (R2 = 0.990). The enthalpy change, ΔH (37.8 kJ mol−1) indicates that dye extraction is endothermic whereas the entropy change, ΔS0 (116.6 J mol−1K−1), reveals a significant change in the entropy during dye uptake. The free energy change ΔG (3.12 kJ mol−1 at 298 K) of CR sorption indicated that the dye retention was not spontaneous at all temperatures. A twofold sorption mechanism involving absorption accompanying ‘solvent extraction’ and/or ‘weak ion exchange’, combined with surface adsorption of dye is proposed. Sorbent packed mini column demonstrated effective percent removal and recovery (101.8%) of CR from water samples using acetone or NaOH as an eluting agent. The study expands the utility of Au NPs/PUFs for reusability and spectrophotometric sensing of trace levels of CR in water. The key attention also includes integrating PUFs utility by improving the selectivity and sensing properties towards textile dyes.

Optimization of ultrasound-assisted anthocyanin extraction from agricultural waste purple corn silk for multifunctional hemp finishes

The utilization of agricultural wastes for textile dyeing has gained popularity due to their safe and environmentally friendly properties, as well as the resource sustainability. Natural dye extraction is usually achieved through solvent extraction, which is time-consuming, requires a lot of solvent, and degrades desired compounds at high temperatures. Thus, this study investigated ultrasound-assisted anthocyanin extraction from agricultural waste purple corn silk as natural functional colorants for hemp finishes, given the numerous health benefits associated with anthocyanin. In order to optimize the extraction processes and evaluate the synergistic impact of these conditions, response surface methodology was implemented. The optimum conditions were 1:15 material-liquid ratio, 47% ethanol concentration, 60°C, and 20 min, yielding 240.25 mg·L‒1 anthocyanin. The extracted anthocyanin was used for dyeing hemp fabrics and demonstrated satisfactory colorfastness, antibacterial action on both S.aureus and E.coli, with E.coli being more effective, and strong antioxidant (>80%). The dyed fabrics also exhibited their great UV shield (UPF value > 40+). Anthocyanin derived from purple corn silk could therefore be utilized as a natural functional color for medical and health products. Also, purple corn silk contains more anthocyanin than other natural sources, making it a promising natural anthocyanin resource in textile industry.

Eco-friendly utilization of microwaves for extraction of dye from logwood and Its application onto silk

For minimizing the pollution associated with synthetic colorants, the world again is going to realize the benefits of natural colorants in applied fields such as textiles, food flavors, etc. As part of the ongoing research project, hematein is being investigated as a potential natural colorant derived from logwood chips, and its implementation on silk fabric is being investigated under the effect of microwave radiations. A number of dyeing variables, including pH, dyeing duration, temperature of the dye bath, volume of extraction, and salt concentration, have been investigated, and the effect of isolation medium has also been evaluated. For new shades with improved fastness ratings, extracts of various sustainable bio-mordants and chemical mordant such as salts of aluminum and copper, and tannic acid were also used. An experiment revealed that treating un-irradiated silk with 40 mL of methanolic extract with a pH of 2, irradiated for 6 min, produced outstanding outcomes when dyed at 90°C for 60 min. The dyeing process included the addition of 9 g of salt per 100 mL of solution as an exhausting agent. In these circumstances, the utilization of sustainable mordants has not only enhanced the ratings of color fastness but has also rendered the procedure more environmentally friendly and less polluting. Therefore, microwave radiation has great potential for extracting colorants from plants and effectively applying them to natural materials under decreased conditions.

Prediction of environmental suitability for Haematoxylum campechianum: a proposal to promote reforestation in Mexico

Models of potential distribution and ecological niche allow to estimate priority areas for the management of species of interest, as well as to identify variables related to environmental suitability and predict the behavior of species in the face of anthropogenic disturbances. Logwood (Haematoxylum campechianum) is a species that we consider a natural heritage in southeastern Mexico because of its ecological role and the current and historical use of its wood. This species is present in different vegetation types and even dominates in some ecosystems called "tintales", which have been exploited for dye extraction in past centuries. This, combined with changes in land use for livestock, agriculture, and other anthropogenic activities, has affected the Logwood´s distribution and connectivity of its populations. We modeled the potential distribution of H. campechianum and evaluated the feasibility of reforestation with this species in southeastern Mexico. For this purpose, we included 638 occurrence points and used the MaxEnt algorithm for modeling, analyzing different parameters. We used the potential distribution model, accessibility to the areas and water availability to calculate a feasibility index for reforestation. The environmental suitability for the species is more present in southeastern Mexico, conditioned by the aridity index, the maximum temperature of the coldest month and the warmest month. The greatest percentage of areas with high feasibility indexes for reforestation are found in Campeche, apparently a key state for the conservation and management of the species. This study can be the starting point for implementing reforestation programs with H. campechianum and can be used as an example to apply to other species with patrimonial value.

The Extraction of Alcea Rosea Organic Dye and Its Characterization of Optical Properties

In the present study, the optical properties of a natural dye extracted from Alcea rosea flowers were investigated. The color extraction procedure was performed using a nontoxic solvent ethanol to enhance human safety and the ecological framework. Fourier transform infrared spectroscopy was employed to determine the functional groups of the natural dye obtained from Alcea rosea flowers. The optical properties of dye were achieved by the directed thin film using UV-Vis spectroscopy and analyzed absorption spectra, coefficients, refractive indices, extinction coefficients, and optical energy bandgap. A broad absorption band occurs over an extensive waveband with peak at 380 nm. The occurrence of a low indirect bandgap in a thin film was discerned at 3.9 eV, with Urbach energy noticed in a state of 0.23 eV.

Study of Dyeing With Natural Extract of Butterfly Pea Flowers (Clitoria Ternatea) on Cotton Fabrics

Objective: This study aims to optimize the dye extraction and dyeing variables in cotton fabrics using dried Butterfly Pea flowers (Clitoria ternatea), in order to evaluate its potential as a natural dye in the dyeing of cotton fabrics. Theoretical Framework: This research is presented based on fundamentals related to dyeing with natural dyes, dye extraction and pre-mordanting procedures, as well as studies related to the dyeing of cotton fabrics. Method: This research was carried out by varying the dye extraction temperature and dyeing parameters, which were documented and optimized. The pre-mordanting process was also used with 5 different biomordants, at the end the washing and friction fastness properties of the fabrics dyed with and without the pre-mordanting process were observed. Results and Discussion: The results showed that the best dye removal temperature was 70°C and the optimized dyeing conditions were a temperature of 50°C, time of 60 minutes and pH 3. In general, the use of biommordants did not promote improvements in solidity interactions. Research Implications: The use of natural dye made from Butterfly Pea flowers in dyeing provides a blue color to the cotton fabric, which is difficult to achieve. Originality/Value: The use of natural dye made from Butterfly Pea flowers in dyeing provides a blue color to the cotton fabric, which is difficult to achieve.

Extraction of Dye from Waste Blue Gel Pen Ink Using the Voltine Method and Its Application in Fabric Dyeing: An Eco-friendly Approach

Extraction of Dye from Waste Blue Gel Pen Ink Using the Voltine Method and Its Application in Fabric Dyeing: An Eco-friendly Approach

Extraction of flavonoid dyes from vine tea (Ampelopsis grossedentata) waste and application in bleached pulp dyeing

AbstractNatural dyes are receiving more attention due to wide and renewable resources and their functionalities. This study delved into the optimal conditions for extracting Ampelopsis grossedentata flavonoid dyes (AGFDs) from vine tea waste, resulting in a dye sample with a total flavonoid extraction percentage of 27.4 %. Ultraviolet (UV), Fourier‐transform infrared (FTIR) and liquid chromatography–mass spectrometry (LC–MS) analysis revealed the presence of 18 flavonoids in AGFD. Additionally, various factors, including pH, light exposure, temperature, metal ions, and redox agents were found to impact the stability of AGFD. Moreover, the dyeing performance of AGFD for the bleached chemical pulp was investigated. Under optimal conditions, the AGFD‐dyed pulp displayed a vibrant yellow hue and excellent colour fastness when using aluminum potassium sulphate dodecahydrate (KAl(SO4)2·12H2O) as a mordant with a dyeing uptake level up to 88 %. FTIR and scanning electron microscopy (SEM) analysis demonstrated that AGFD chemically bound to the pulp fibre. Remarkably, the hand sheet made from the AGFD‐dyed pulp exhibited thermal stability, physical strength properties and antibacterial activity against Escherichia coli and Staphylococcus aureus. Furthermore, the peroxide value of cheese packaged with the AGFD‐dyed pulp hand sheet was only 43 % of that of the undyed one, indicating its good antioxidant properties. This study highlights the promising potential of AGFD in the production of functional coloured paper.

Extract of Papaver Rhoeas for Daylight Imaging of Latent Fingerprints

AbstractThe extraction of natural red dye (PR) from the flower Papaver rhoeas (common poppy) and its adsorption on montmorillonite clay (PR@MM) was reported. The powder PR@MM was used for the development and visualization of LFPs taken on common household, nonporous, and colored surfaces in daylight using powder dusting method without any pre‐ or posttreatment and equipment. The information of level 1 (ridge classification) and level 2 (minutiae details) from the fingerprint can be obtained using PR@MM powder.

Preparation of a New Hexafluorobutanol-Farnesol Based Supramolecular Solvent and Its Application in Microextraction of Sudan Dyes From Beverage and Water Samples.

In this work, a new supramolecular solvent (SUPRAS) was prepared for the first time using hexafluorobutanol (HFB) and farnesol (FO). FO acts as an amphiphile and HFB as a coacervation inducer and density regulator. The method of dispersive liquid-liquid microextraction followed by high-performance liquid chromatography, supported by a vortex technique, was established using the prepared SUPRAS for the determination of Sudan dyes in aqueous samples. The extraction parameters, including FO content, HFB content, vortex time, salt addition, and solution pH, were thoroughly investigated and optimized. Under the optimized conditions, the linearity range is 10-750ng/mL for Sudan I, and 10-1000ng/mL for Sudan III and Sudan IV, respectively. The limits of detection for Sudan dyes were in the range of 0.8-3.1ng/mL. The inter- and intra-day relative standard deviations for Sudan dyes were in the range of 1.3%-4.1% and 0.2%-2.6%, respectively. Finally, the proposed method was applied to the determination of Sudan dyes in beverage and river water samples with recoveries ranging from 93.9% to 122.1%. Compared to conventional techniques for the extraction of Sudan dyes in real samples, the proposed method is simpler, faster, and more environmentally friendly.

The Study of the Biologically Active Effect of the Rubia Tinctorum L. Plant on Rats with Experimental Kidney Stone Disease and Issues of Introduction

Since ancient times, madder dye (Rubia tinctorum L.) has been used in Uzbekistan to help alleviate stone deposits in organs. In the experiment we conducted, we aimed to demonstrate that this plant can prevent the occurrence of kidney stone disease in rats using an induced model of the disease. The kidney stone disease model in rats was created by administering ethylene glycol and ammonium chloride to the animals over a period of 10 days. The substances contained in the madder dye plant mitigated the effects of the substances used to induce the disease. According to the study results, simultaneous oral administration of the madder dye extract prevented the development of kidney stone disease in rats. The extract of Rubia tinctorum L. was found to be highly effective, showing a significant nephroprotective effect due to its specific and rich composition of terpenes and terpenoids.

Removal process of an industrial dye using a biosorbent: characterization, kinetic, equilibrium, and thermodynamic studies

Adsorption-based removal is a highly efficient environmental phenomenon employed to eliminate various dyes, such as crystal violet (CV), which is prevalently used in the textile industry and subsequently discharged into natural ecosystems. This study aims to utilize natural bentonite clay sourced from Algeria for the extraction of cationic dye (CV) from wastewater. The characterization of the bentonite was conducted using Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), and X-Ray Diffraction (XRD). Evaluations assessed the impact of various parameters including pH, stirring time, temperature, and initial dye concentration on the adsorption efficiency. Optimal conditions for the maximal adsorption of CV were determined to be 430.18 mg g-1 at an adsorbent-to-dye solution ratio of 1 g L-1, pH 11.06, an equilibrium time of 40 minutes, and a temperature of 40°C. The adsorption kinetics were best described by the pseudo-second-order model, while the Freundlich isotherm model aptly described the adsorption isotherms. Thermodynamic parameters underscored the spontaneous and exothermic nature of the crystal violet removal process using raw bentonite. This research provides novel insights into the effective removal of a cationic dye from water and wastewater using Algerian bentonite clay.

Extraction of Natural Dye using Peels of Citrus Fruits for Enhancing Color Fastness of Fabrics

The current study investigates the extraction of dyestuff using citrus fruits and assesses its color, light, rubbing, and perspiration fastness. For the experimental study, three types of citrus fruits—orange, lemon, and grapefruit—were chosen to extract dye from their peels. The dye was applied to two types of fabrics (100% cotton and a blended fabric made of polyester-cotton (PC) with a ratio of 50:50) using the conventional aqueous method. The results revealed the remarkable efficacy of orange dye on both fabric types, demonstrating excellent color fastness attributes, with a minor preference for PC fabric in washing fastness. In contrast, lemon dye displayed better washing fastness properties on the tested materials as well as considerable staining potential. Grapefruit dye performed exceptionally well in terms of water and perspiration fastness. Future research could focus on improving dye extraction techniques for citrus fruits to increase color absorption and penetration. Determining various solvents, time duration for dyeing, and temperature settings could enhance the dyeing performance and effectiveness of natural dyes in different industrial applications. Further studies could also conduct life cycle assessments to measure the environmental impact of using citrus peels as a natural dye source compared to synthetic dyes in the textile industry.

Research of coloristic properties of textile materials dyed with natural dyestuff

The development of an environmentally friendly technology for dyeing textile materials for various purposes implies the modification of technological processes by using less harmful consumables, namely, dyes of plant origin. Dyes of plant origin have biological decomposability and the most friendly to human nature, and many of them also have a complex of antibacterial and medicinal properties. The purpose of this work is to study the colorimetric properties and develop mathematical models of the obtained dyes based on natural herbs. Extracts of dyes for dyeing textile materials are obtained from the peel of onions, walnut shell, tansy and hypericum with the addition of the following modifying components: aluminum-potassium alum or copper sulfate. The study of the coloristic properties of the obtained dyes was carried out using the Konica Minolta CM-3600d device in the color coordinates 360-700 nm. The results of the study showed the high efficiency of the use of modifying additives in the composition of dyes on the quality of coloring of textile materials. Based on the results of coloristic studies, regression equations and mathematical models describing the effects of staining depth and color reflection on the intensity of tissue coloring are constructed. Due to the active extraction of natural dyes and expanded color shades, the introduction of natural dyes into the textile industry is an urgent task. The introduction of developed natural dyes with modifying additives will improve the hygienic properties of products and increase the environmental friendliness of the finishing process.

Extraction of natural dye from Broccoli (Brassica oleracea) and evaluation of its antimicrobial, ultraviolet and dyeing properties on cotton fabrics

Extraction of natural dye from Broccoli (Brassica oleracea) and evaluation of its antimicrobial, ultraviolet and dyeing properties on cotton fabrics

Sustainable Assessment of Bio-Colorant from Bakain Bark (Melia azedarach L.) for Dyeing of Cellulosic and Proteinous Fabric.

The current study proceeded to reduce the environmental hazards spreading worldwide due to synthetic dyes. To overcome these problems, eco-friendly natural dyes are introduced as alternative sources of synthetic dyes. The present study was focused on exploring the bio-colorant of the aqueous and acidic extract of the bark of Melia azedarach L. for the dyeing of both silk and cotton samples. The results of the extraction medium specified that the aqueous extract gave maximum colorant solubility and upon fabric dyeing produced higher color strength in contrast to the acidic medium. The optimization experimentation data showed that excellent color strength of silk fabric was found at 45 min dyeing time duration, in 35:1 mL dye extract, and using 2% salt (NaCl) as an exhausting agent, whereas cotton fabric showed the maximum K/S value at 60 min dyeing time, in a 45:1 mL liquor ratio, and with the use of 2% salt. Bio-mordants produce different shades on both fabrics. Bio-mordanting experiments on silk revealed that pre-mordanting with 2% turmeric and 3% pomegranate, and post-mordanting using 3% turmeric and 2% pomegranate produced a darker shade. In the case of cotton, the pre-mordanted samples with 2% turmeric and 3% pomegranate and the post-mordanted samples with 4% turmeric and 4% pomegranate gave the highest color strengths. All the mordanted samples gave excellent fastness ratings. Overall, it has been found that Bakain bark proved to be an excellent source of tannin. The result of this study showed that it could be a cost-effective and eco-friendly dye source for textile progress.

Sustainable ultrasonic extraction of antibacterial Basella alba fruit dye for cotton, silk, and leather

Alternative to synthetic dyes containing harmful compounds, dyes derived from natural sources are gaining popularity due to their safer and eco-friendly nature. This study focuses on extracting red dye from Basella alba fruit and optimising the extraction methods, including ultrasonic bath, ultrasonic probe, and direct heating. The extracted dye was then used for dyeing cotton, silk, and leather without needing a mordant. Furthermore, the antibacterial properties of the extracted red dye were evaluated against skin bacteria. The UV–Visible spectrophotometric analysis revealed that the maximum red colour in the methanol extract (λmax 270 and λmax 542 nm) was achieved at 60 °C for 30 min using the ultrasonic water bath extraction method, followed by the ultrasonic probe and direct heating methods. The FTIR spectra confirmed the presence of flavonoids, betacyanin, and gomphrenin-I in the extracted dye. The ultrasonic dyeing process at 50 °C yielded a K/s value 6.3 for the dyed cotton, silk, and leather without using a mordant. Additionally, the fatness test indicated a high grade of 0.5–1.5 for the ultrasonic dyeing method compared to other dyeing techniques. The extracted dye exhibited significant antibacterial activity against all Pseudomonas sp. after extraction in methanol, with the highest inhibition observed against Pseudomonas sp. with a MIC of 1.56 mg/ml.

Spectroscopic study of wemple-didomenico empirical formula and taucs model to determine the optical band gap of dye-doped polymer based on chitosan: Common poppy dye as a novel approach to reduce the optical band gap of biopolymer

This study investigates the effect of a natural dye extracted from common poppy (Papaver rhoeas) waste flowers on the optical properties of chitosan (CS) films. The extraction of natural dyes from waste flowers can be considered a new field for research in green chemistry. CS films are flexible and biodegradable but have low optical activity and band gap, limiting their applications in optical devices. The doped CS polymer with different concentrations of Papaver rhoeas dye exhibited enhanced optical properties. Also, 30 % glycerol was added as a plasticizer to omit film brittleness. The FTIR examinations is helpful to propose a mechanism that explains the interaction of the dye with the host polymer. The UV–vis spectroscopic examination establish that the optical characteristics of the films can be modified by adjusting the dye concentration. Furthermore, optical absorption properties are described using the Tauc non-direct transition model, revealing an approximate optical band gap of 1.64 eV. This band gap defines the energy required for electron transitions, elucidating the material’s electronic characteristics. The extinction coefficient (k) and refractive index (n) of the CS-doped films’ shows a dispersion behavior at visible regions of EM radiation. The Wemple-DiDomenico single oscillator model was used to investigate the n dispersion and determine the oscillator energy equivalent to the optical band gap. Additionally, calculations have been performed on optical dielectric properties and optical conductivity. The Urbach energy was measured and used to detect the structure of the films. The findings underscore the potential applications of these natural dye-doped CS films in eco-friendly materials and optical devices.

Evaluating Supercritical Carbon Dioxide Extraction vs. Conventional Aqueous Extraction of Natural Dyes from Hypericum triquetrifolium for Textile Fibers Dyeing

Evaluating Supercritical Carbon Dioxide Extraction vs. Conventional Aqueous Extraction of Natural Dyes from Hypericum triquetrifolium for Textile Fibers Dyeing