Dust Samples Research Articles

Phthalate monoesters accumulation in residential indoor dust and influence factors

Phthalate monoesters (mPAEs) possess biological activity that matches or even exceeds that of their parent compounds, phthalate esters (PAEs), negatively impacting humans. Indoor dust is the main carrier of indoor pollutants. In this study, indoor dust samples were collected from 46 households in Changchun City, Jilin Province, in May 2019, and particulate and flocculent fibrous dust was used as the research target to analyze the concentration and compositional characteristics of mPAEs, primary metabolites of five significant PAEs. The influence of factors such as architectural features and living habits in residential areas on exposure to mPAEs was explored. Ten suspected enzyme genes along with two metabolic pathways with the ability to degrade PAEs were screened using PICRUSt2. The results showed that the total concentrations of the five mPAEs in the indoor dust samples were particulate dust (11.49–78.69 μg/g) and flocculent fibrous dust (21.61–72.63 μg/g), respectively. The molar concentration ratio (RC) of mPAEs to corresponding PAEs significantly differed among chemicals, with MMP/DMP and MEP/DEP sporting the highest RC values. Different bacterial types have shown distinct influences against mPAEs and PAEs. Enzyme function and metabolic pathway abundance had a significant effect on the concentration of some mPAEs, mPAEs are most likely derived from microbial degradation of PAEs.

The spatial distribution and source of heavy metals in soil-plant-atmosphere system in a large coal mining area

Due to the lack coupling analysis of heavy metals in soil-plant-atmosphere system, the migration and transformation of heavy metals remains unclear. In this study, 240 surface (0–20 cm) soil samples, 365 plant samples and 168 atmospheric dust samples were collected in a large coal mining area, in which selected heavy metals arsenic (As), cadmium (Cd), chromium (Cr), copper (Cu), nickel (Ni), plumbum (Pb), zinc (Zn) were analyzed, to elucidate the spatial distribution and source of heavy metals and their bioavailability. According to the results of ArcGIS mapping analysis, the distribution patterns of Cd, Cu, Pb, and Zn in the three media are similar, while the distribution characteristics of Cr and Ni are highly consistent. The factors contributing to these spatial distribution characteristics of heavy metals could be associated with human activities and the characteristics of the elements. Compared with the background value, Zn, Cr, Pb in soil, Zn, Cr, Cu in plants and Zn, Pb, Cu in atmospheric dust apparently accumulated. The geological accumulation pollution index (Igeo) shows that there exist mild to moderate levels of Cr and Cd pollution in soil, and mild to moderate levels of Cd, Cr, Pb, and Zn pollution in the air. The evaluation of potential risks of heavy metals showed moderate ecological hazards in soil and strong ecological hazards in atmospheric dust. The sources of heavy metals were assessed using principal component analysis (PCA), land use type, and spatial analysis. Anthropogenic factors are the main sources of heavy metal content. Coal-related industrial processes related to coal, sewage irrigation, the use of agricultural chemicals, and vehicle emissions may be anthropogenic sources of heavy metals.

Features of the chemical composition of fine suspended particles in the atmospheric air of residential and industrial zones of the city of Sibay, Republic of Bashkortostan

Introduction. Atmospheric particulate matter as a negative environmental factor can be a significant hazard depending on their size, morphometric and physicochemical characteristics. The purpose of the study. To investigate the elemental composition of finely dispersed suspended particles in the atmospheric air of the industrial zones of the mining center of the Bashkir Trans-Urals - the city of Sibay. Materials and methods. Air sampling was carried out in the industrial area of ​​Sibay using an AVA-3-240/180-01 automatic three-channel air aspirator with AFA-VP-20 filters. Microscopy of samples and determination of the elemental composition of dust emissions were carried out at the Interdisciplinary Center “Analytical Microscopy” of the Kazan Federal University (Kazan) on a universal analytical complex for scanning field emission electron microscopy Merlin (Carl Zeiss). Results. On electron micrographs, there were identified particles of various sizes, mostly round in shape with clear edges, located solitary. In the automatic mode of processing the spectra, the peaks of the elements in the spectrum were automatically recognized and identified. In addition to carbon and oxygen, the calcium, iron, silicon, potassium, aluminium, copper, sulphur, sodium and magnesium are main chemical constituents of particulate matter encountered at all sampling points. Zinc was present in dust samples at three points, scandium, titanium, cobalt, barium, and manganese – only at one point. The possibility of the relation between the content of fine particles in the air and the increased incidence of cardiovascular, bronchopulmonary diseases, including asthma, in the population of Sibay is discussed. Limitations. The study of the elemental composition of fine dust in the city of Sibay was carried out using atmospheric air samples taken at 5 points located in residential and industrial areas. Conclusion. The increased content of fine particles in the atmospheric air of the city of Sibay increases the risks of respiratory and cardiovascular diseases, as well as other health abnormalities, in the population permanently residing near industrial zones. The obtained data on the parameters of dust particles are the basis for assessing the share contribution of industrial enterprises to air pollution and making management decisions to improve the environmental situation in the industrial center of the mining region.

Fungal Biodeterioration Risk in Monastic Libraries without Climate Control.

Fungi have always posed an unquestionable threat to heritage collections worldwide. Now, in a future of climate change, biological risk factors may have to be considered even more than before. Models and simulations to assess possible impacts a changing outdoor climate will have on indoor environments and, in turn, on biodeterioration are still underdeveloped and require a more substantial data basis. This study aimed at filling some of these knowledge gaps through a broad-based approach combining microclimatic and microbiological monitoring in four historic libraries in Austria with an uncontrolled indoor climate: Altenburg Abbey, Melk Abbey, Klosterneuburg Monastery and the Capuchin Monastery in Vienna. Data were generated from thermohygrometric sensors, cultivation-dependent air- and surface sampling and further surface dust sampling for cultivation-independent analyses. Results gave insights on the status quo of microbiological loads in the libraries and outdoor-indoor relationships. Influences of the geographic location and room-use on corresponding indoor fungal profiles were identified. Lower fungal diversities were found at the most rural site with the strongest climatic fluctuations and extreme values than in the most urban, sheltered library with a very stable climate. Further, the humidity-stabilizing potential of large collections of hygroscopic materials, such as books, was also examined. Implications for a sustainable approach to prevent future biodeterioration are discussed, supporting the long-term preservation of these valuable historic collections.

The oxidative stress-dependent pulmonary inflammation of inhalable multi-walled carbon nanotube-containing nano-concrete dust and its comparison with conventional concrete dust and DQ12

Nano-concrete, which is an admixture of nanomaterials in concrete recipes, has been investigated to overcome the limitations of existing concrete, such as its stability and strength. However, there is no information on the human health effects of broken-down dust released during the construction and demolition efforts. In this study, we prepared an inhalable fraction of multi-walled carbon nanotube-containing nano-concrete dust and performed comparative toxicity studies with conventional concrete dust and DQ12 using a rat intratracheal instillation model. Although the recipes for concrete and nano-concrete are entirely different, the pulverized dust samples showed similar physicochemical properties, such as 0.46–0.48 µm diameter and chemical composition. Both concrete and nano-concrete dust exhibited similar patterns and magnitudes, representing acute neutrophilic inflammation and chronic active inflammation with lymphocyte infiltration. The toxicity endpoints of the tested particles at both time points showed an excellent correlation with the reactive oxygen species levels released from the alveolar macrophages, highlighting that alveolar macrophages are the primary target cells and that the oxidative stress paradigm is the main toxicity mechanism of the tested particles. In addition, the toxicity potentials of both concrete and nano-concrete dust were more than 10 times lower than that of DQ12.

Health and environmental risk assessment of mercury in outdoor and indoor dust in artisanal and small-scale gold mining area in Amansie-west district in the Ashanti Region of Ghana.

Mercury (Hg) pollution around artisanal and small-scale gold mining (ASGM) areas has been of much concern. Many studies have reported elevated Hg concentrations in environmental media, but studies on dust relating to inhalation exposure of Hg around ASGM area are limited. In this study, we investigated Hg in indoor and outdoor dust to reveal environmental and human health risk around ASGM in Amansie West district, Ghana. Indoor and outdoor dust samples were collected from Manso Abore and Manso Nkwanta in Ashanti Region. Concentration of Hg in the samples were analyzed using a direct Hg analyzer. The mean and median value of Hg concentration in the indoor dust (n = 31) were 2.2 ± 3.6mg/kg and 0.72mg/kg respectively while that of the outdoor dust (n = 60) were 0.19 ± 0.48mg/kg and 0.042mg/kg, respectively. The mean and median Hg concentration in indoor dust were about 11 and 17 times higher respectively than that in the outdoor dust. The Hg concentration in the indoor dust was statistically significantly higher than that of the non-miner in Manso Abore (p < 0.05) but was not significant in Manso Nkwanta, probably due to higher mining activity. The geo-accumulation index of the outdoor dust ranged from unpolluted to extremely polluted while that of the indoor dust ranged from moderately polluted to extremely polluted. Health risk assessments suggested that there was no potential non-carcinogenic health effect for Hg exposure relating to the dust to residents living in rooms of miners and non-miners.

Phthalate Acid Esters (PAEs) in Indoor Dust from Decoration Material Stores: Occurrence, Sources, and Health Risks.

Phthalate acid esters (PAEs) are one of the most widely used plasticizers globally, extensively employed in various decoration materials. However, studies on the impact of these materials on indoor environmental PAE pollution and their effects on human health are limited. In this study, forty dust samples were collected from four types of stores specializing in decoration materials (flooring, furniture boards, wall coverings, and household articles). The levels, sources, exposure doses, and potential health risks of PAEs in dust from decoration material stores were assessed. The total concentrations of Σ9PAE (the sum of nine PAEs) in dust from all decoration-material stores ranged from 46,100 ng/g to 695,000 ng/g, with a median concentration of 146,000 ng/g. DMP, DEP, DBP, and DEHP were identified as the predominant components. Among all stores, furniture board stores exhibited the highest Σ9PAE (159,000 ng/g, median value), while flooring stores exhibited the lowest (95,300 ng/g). Principal component analysis (PCA) showed that decoration materials are important sources of PAEs in the indoor environment. The estimated daily intakes of PAEs through non-dietary dust ingestion and dermal-absorption pathways among staff in various decoration-material stores were 60.0 and 0.470 ng/kg-bw/day (flooring stores), 113 and 0.780 ng/kg-bw/day (furniture board stores), 102 and 0.510 ng/kg-bw/day (wall covering stores), and 114 and 0.710 ng/kg-bw/day (household article stores). Particularly, staff in wall-covering and furniture-board stores exhibited relatively higher exposure doses of DEHP. Risk assessment indicated that although certain PAEs posed potential health risks, the exposure levels for staff in decoration material stores were within acceptable limits. However, staff in wall covering stores exhibited relatively higher risks, necessitating targeted risk-management strategies. This study provides new insights into understanding the risk associated with PAEs in indoor environments.

Evaluation of concentration and characterization of potential toxic elements and fluorine in ambient air dust from Iran’s industrial capital: A health risk assessment using Monte Carlo simulation

The emission and adsorption of mineral elements to dust from geogenic and anthropogenic sources are health challenges in residential areas. This study investigated, for the first time to the best of our knowledge, the presence of potentially toxic elements (PTEs), rare earth elements (REE) and fluorine (F) in collected dust samples from central Iran. Their associated health risks were estimated based on the Monte Carlo simulation. Results show that the morphology of the collected dust was uniform spherical particles and the predominant elements were Si and Ca. The highest concentration of PTEs was for Ca (mean: 36574 mg/kg) and Fe (mean: 30189 mg/kg) and the mean concentrations of As, Ni, Pb, Mn and Zn exceeded World Health Organization (WHO) guidelines, likely due to the anthropogenic activities such as metal melt factories. Fluorine averaged 159.4 mg/kg, and some detected elements originated from industrial and natural sources. The 5th, 50th, and 95th percentiles of the estimated Hazard Index (HI) were 0.13, 0.43, and 0.77, respectively, in adults and 1.00, 3.03, and 5.99, respectively, in children. The carcinogenic risk (LTCR) for adults and children exceeded the safety range (1 × 10−4), and their highest percentile was calculated at about 2.03 × 10−4 and 1.83 × 10−4, respectively. Furthermore, Ni was the most effective elements in LTCR. As a consequence, findings suggest a high potential carcinogenic risk due to the emission of dust in central Iran, especially for children, and the controlling of possible sources would benefit public health.

Distribution Characteristics of Atmospheric Microplastics in Typical Desert Agricultural Regions.

We examined the distribution characteristics of atmospheric microplastics in typical desert agricultural regions, with a focus on the agricultural areas surrounding the Taklamakan Desert, Xinjiang, China. We collected samples of total suspended particulate matter (TSP), atmospheric deposition, and atmospheric dust using both active and passive collection methods. The chemical composition, particle size, shape, and color of atmospheric microplastics were examined using a stereomicroscope and a Fourier-transform infrared spectrometer to analyze their characteristics. The results showed that the primary chemical compositions of microplastics included polypropylene (PP), polyethylene, polyethylene terephthalate, polymethylmethacrylate, and cellophane. Particle sizes were mainly within the range of 0 to 1000 μm. Fibrous microplastics constituted the majority of the TSP and atmospheric deposition, whereas film-like microplastics constituted the largest proportion of atmospheric dustfall. The deposition flux of atmospheric microplastics in the first quarter was measured at 103.21 ± 22.12 particles/m2/day, which was lower than that observed in conventional agricultural areas. The abundance of microplastics in atmospheric dustfall was found to be 1.36 particles/g. The proportion of PP microplastics in atmospheric dustfall can be as high as 35%. Through a comparison of microplastic content in TSP during dust storms and under normal weather conditions, it was found that dust storms can lead to an increase in the abundance of microplastics within the atmospheric TSP. The present study provides a scientific basis for understanding the distribution of atmospheric microplastics in typical desert agricultural regions. Environ Toxicol Chem 2024;43:1982-1995. © 2024 SETAC.

Enhancement of Sustainable Recycling Systems for Industrial Waste in South Korea via Hazardous Characteristics Analysis

The South Korean government has implemented an acceptance system to promote the high-quality recycling of waste. Industrial waste generators must provide “hazardous characteristics data” to recycling operators. Nonetheless, ~80% of industrial safety accidents in South Korea occur during recycling, most involving fire or explosions. Moreover, a gap in safety management exists during ‘Circular Resource’ acceptance if the target substance is not regarded as waste. In this study collected data on hazardous waste characteristics. From 62 waste generators, 72 waste samples were collected, accounting for most of the resources accepted for recycling, including waste synthetic polymers, slag, dust, waste sand, and waste foundry sand. Then, the hazardous characteristics, as stated in the Ministry of Environment notifications, were assessed. Leaching toxicity was detected in one slag sample and six dust samples. The Cd, Cu, As, Pb, Zn, Ni, Hg, F, and CN levels dissatisfied the Soil Contamination Warning Standard in 31 samples. Explosivity was not detected in any sample, whereas flammability was detected in one waste synthetic polymer sample. The results revealed 15 cases of potential flammability. Flammability is legally defined as below the criteria if the combustion speed criterion is not met. However, in the case of flame ignition, which could cause large fires and safety accidents, the relevant notification should be revised. In this study, we aimed to improve the gap between the hazardous waste management systems and industrial fields through actual measurements of hazardous characteristics. By doing so, we seek to contribute to the prevention of environmental and safety accidents. By continuously accumulating data and utilizing actual measurements, we aim to revise and enhance relevant regulations, ultimately improving the hazardous characteristics of waste management systems.

Concentrations, Profiles, and Potential Sources of Liquid Crystal Monomers in Residential Indoor Dust from the United States.

Liquid crystal monomers (LCMs) are biphenyl- or cyclohexane-based organic chemicals used in electronic digital displays, and several of them possess bioaccumulative and toxic properties. Little is known about their occurrence in indoor dust from the United States. We analyzed 60 LCMs in 104 residential indoor dust samples collected from 16 states across the United States. Forty-seven of 60 LCMs were detected in dust samples at a median ∑LCM concentration of 402 ng/g (range: not detected to 4300 ng/g). Trans-4-propylcyclohexyl trans,trans-4'-propylbicyclohexyl-4-carboxylate (MPVBC) and (trans,trans)-4-fluorophenyl 4'-pentyl-[1,1'-bi(cyclohexane)]-4-carboxylate (FPeBC) were frequently detected in dust samples. We investigated potential sources of LCMs in dust by determining concentrations and profiles of these chemicals in smartphone screens, desktop and laptop computer monitors, and displays of other electronic devices and found that profiles in smartphones matched closely with those found in dust. The calculated median daily intake of ∑LCM through dust ingestion was 1.19 ng/kg bw/d for children, whereas that through dermal absorption was 0.18 ng/kg bw/d for adults in the United States.

Application of Artificial Intelligence to the Alert of Explosions in Colombian Underground Mines

The use of Artificial Intelligence (AI), particularly of Artificial Neural Networks (ANN), in alerting possible scenarios of methane explosions in Colombian underground mines is illustrated by the analysis of an explosion that killed twelve miners. A combination of geological analysis, a detailed characterization of samples of coal dust and scene evidence, and an analysis with physical modeling tools supported the hypothesis of the existence of an initial methane explosion ignited by an unprotected tool that was followed by a coal dust explosion. The fact that one victim had a portable methane detector at the moment of the methane explosion suggested that the ubiquitous use of these systems in Colombian mines could be used to alert regulatory agencies of a possible methane explosion. This fact was illustrated with the generation of a database of possible readouts of methane concentration based on the recreation of the mine atmosphere before the explosion with Computational Fluid Dynamics (CFD). This database was used to train and test an ANN that included an input layer with two nodes, two hidden layers, each with eight nodes, and an output layer with one node. The inner layers applied a rectified linear unit activation function and the output layer a Sigmoid function. The performance of the ANN algorithm was considered acceptable as it correctly predicted the need for an explosion alert in 971.9 per thousand cases and illustrated how AI can process data that is currently discarded but that can be of importance to alert about methane explosions.

SWOT analysis of risk prevention and control of microorganism pollution in shopping malls and supermarkets

To understand the status and problems of microbial pollution in shopping malls and supermarkets in China. Microbial pollution in shopping malls and supermarkets was assessed by literature search, key information extraction and analysis. The strengths, weaknesses, opportunities and threats(SWOT) of risk control of pathogenic microorganisms in shopping malls and supermarkets were analyzed by SWOT analysis. Common bacteria in the indoor air of shopping malls and supermarkets included staphylococcus and Bacillus, and common fungi include Aspergillus and Penicillium. The bacteria detected in dust samples, escalator surfaces and floor surfaces were mainly Proteobacteria and Actinomyces. The complete public places laws and regulations, standards and health supervision system were the advantages of the risk prevention and control countermeasures of microbial contamination in shopping malls and supermarkets. At the same time, it also had the disadvantages of incomplete microbial-related indexes in the premises, and insufficiently detailed countermeasures for prevention and control in the premises. There were opportunities for multi-sectoral participation and post-licensing risk prevention, and it was also facing challenges brought by many factors affecting the health microenviroment and over-disinfection. The main sites for microbial risk prevention and control in superstore-type public places included high-frequency contact areas, key public supplies and utensils, indoor air, etc. , which could be prevented and controlled through a variety of measures such as controlling the release of the source, dilution and reduction, disinfection and denaturation, etc. , and exploring a comprehensive prevention and control system that involves the autonomy of the organization, industry self-regulation, collaboration of multi-government departments, and participation of the whole society.

53. Practical applications of Marek’s disease virus detection by qPCR from dust samples

53. Practical applications of Marek’s disease virus detection by qPCR from dust samples

Source Identification of Urban dust Heavy Metals Using in Situ and Satellite Data in Three Mega Cities of Iran.

The aim of this study was an integrative assessment of heavy metals associated with urban dust data in Iran (Ahvaz, Isfahan, and Shiraz). Samples of urban dust from four sites (traffic, industrial, residential, and Greenland) were collected, and ten heavy metal concentrations were determined using ICP_MS in each sample. The highest average concentrations of metals were at the traffic site for the Mn, Zn, and Cr metals. The PMF model indicates a higher percentage of Pb participation, which shows the importance of traffic resources. The highest non-carcinogenic risk (HI) was for the Cr and the carcinogenic risk was tolerable. To evaluate aerosol and its effects on urban dust, Aerosol Optical Depth (AOD) data were used during 2003-2023. According to the Mankendall test, the trend of AOD has been increasing in Esfahan (p_value < 0.05) and Shiraz. Although Ahvaz's AOD is about two times greater than other cities, the aerosol trend in Ahvaz is decreasing.

Preliminary Study on Mercury and Lead in the Ambient Air of Metro Manila, the Philippines

Despite being acknowledged as an air pollutant, heavy metal contaminants in the atmosphere are not yet well studied in the Philippines. This study aims to assess the particulate matter, as well as mercury and lead concentration, in Metro Manila's ambient atmosphere. A one-hour sampling period was used to collect data at seven sampling stations using a respirable dust sampler with a flow rate of 1.4 m3/min. The mercury concentration was determined using cold vapor atomic absorption spectroscopy, whereas lead concentrations were measured using flame atomic absorption spectroscopy. Taguig had the highest level of total suspended particulates (TSP) at 524.07 μg/NCM, followed by Caloocan (459.92 μg/NCM) and Quezon City (434.50 μg/ NCM). Parañaque reported moderate particulate levels – recorded at 298.95, 291.69, and 347.36 μg/NCM, respectively. Valenzuela had the lowest TSP level at 263.85 μg/NCM. Results show that mercury concentrations were highest in the City of Manila with 0.09 μg/m3, followed by Valenzuela City with 0.009 μg/m3, against the lowest concentration in Taguig City and Quezon City with 0.001 μg/m3. However, based on the legal airborne permissible exposure from the Philippine Occupational Safety and Health Standards, the mercury concentration in the seven cities of Metro Manila did not exceed its 0.5 mg/m3 (50 μg/m3) limit. Furthermore, results revealed that atmospheric lead concentration in Metro Manila existed only in trace amounts (≤ limit of detection). The high concentration of mercury in the City of Manila could be attributed to its high population density combined with massive industrial, commercial, and transport activities. Monitoring the concentration of heavy metals in the atmosphere is critical for the development of effective strategies for reducing the negative impacts of these global pollutants.

Elemental distributions in the marine sediments off Doha, Qatar: role of urbanisation and coastal dynamics

This research investigates the present status and decadal variability of element distributions in the marine sediments off Doha, on the east coast of Qatar. Twenty elements were considered from 11 sediment sampling stations and 3 dust sampling stations by grouping them into major elements, toxic elements, and other trace elements. The results show elevated concentrations of certain toxic and trace elements, including Ba, Be, Co, Cr, Cu, Fe, Mg, V, Zn, Mg, and Ti, in the nearshore region, primarily influenced by the settling of dissolved elements under weak hydrodynamic circulations in the Doha Bay. The relatively higher currents in offshore enable quick advection and dispersion of the elements. On the other hand, the dust deposits have caused significant contributions to the Al, As, Mg, Ca, Sr, Fe, Zn, and Cd concentrations. Decadal variability is evident in element concentrations, which are linked to the urbanisation of the capital city in the State of Qatar. The Cu, Ni, V, Zn, and Cd concentrations indicate a notable increase in recent years compared to the last two decades, with values of about 20.7, 17.9, 25.0, 25.9, 0.66 ppm in 2022. In contrast, a few other elements fluctuate between the decades/years. The results pointed out the increased elemental concentrations in the bay due to the vast expansion of infrastructure facilities in the vicinity of Doha Bay in recent years. The Geoaccumulation Index resulted in a slight pollution of Cd, while other elements are unpolluted. The Degree of Contamination reveals low degree of contamination of sediments, and the Pollution Load Index illustrates no significant pollution in the sediments off Doha.

SPECIATION OF HEAVY METALS AND MICROBIAL CONTAMINANTS IN HARMATTAN DUST WITHIN THE FEDERAL POLYTECHNIC KAURA NAMODA MAIN CAMPUS, ZAMFARA STATE

Harmattan dust is a natural phenomenon contributing to air pollution due to the presence of heavy metals and microorganisms. This research aimed to determine the speciation of heavy metal and microbial contaminants in Harmattan dust samples within the polytechnic Kaura Namoda. The composite sample of each month, namely, December 2023, January 2024, and February 2024, was collected with the aid of a sterilized petri dish. Five extraction phases were carried out, in order of mobility of the metals: exchangeable ion &gt; metal bound with carbonate &gt; metal bound to iron and manganese oxide &gt; metals bound to organic matter and sulfide &gt; residual phase. This was achieved using Tessie’s method and AAS for extraction and analysis. The result for the heavy metals shows Cr (13.6%) and Zn (25.5%) are more abundant in the exchangeable phases in December and January. Metals bound to Fe and MnO extraction phases have Zn (25.50%) abundance in December and January. The residual phase of extraction shows the highest percentage of pb (95.3%) and nickel (85.40%) for December and January. The bacteria and fungi identified are Bacillus cereus, Staphylococcus, Aspergillum, and Clodosporium, respectively. There is no significant difference in physicochemical parameters between the Harmattan dust samples collected in December, January, and February. The percentages of heavy metals in the Harmattan dust are high in the immobility phase of extraction, and bacterial and fungal levels are high in December and January. There is a need for preventive and protective measures to mitigate the health effects associated with...

Per- and polyfluoroalkyl substances (PFAS) in paired tap water and house dust from United States homes

Most people in the United States have been exposed to per- and polyfluoroalkyl substances (PFAS) which have been linked to a wide array of adverse health conditions in adults and children. The consumption of contaminated drinking water is an important human exposure pathway to PFAS. Residential sources also contribute to PFAS exposure through dermal contact and ingestion of house dust, which acts as an aggregate of chemicals from sources like furnishing materials and consumer products. The U.S. Department of Housing and Urban Development (HUD) conducted the first nationwide survey of residential hazards called the American Healthy Homes Survey (AHHS) in 2005, followed by a second survey (AHHS II) in 2017. The U.S. Environmental Protection Agency (EPA) collaborated with HUD on both efforts and subsequently analyzed PFAS in household tap water and house dust collected from the same homes during the AHHS II study. This study leverages these paired samples to investigate potentially important exposure sources and pathways in the residential environment. Here we report results for paired household tap water and house dust samples from 241 homes for 13 and 16 PFAS chemicals, respectively. All 13 targeted chemicals were detected in the household tap water samples with detections ranging from 100 % for PFBS to 1 % for PFNS, and all 16 targeted chemicals were detected in the house dust samples with detections ranging from 97 % for PFOA to 9 % for PFNS. Four chemicals (PFOA, PFOS, PFHxS, and PFHpA) were measured above the limit of detection in at least 50 % of the samples in both media. All households had at least one of the targeted PFAS detected in both their tap water and house dust. Results provided evidence that geographical factors, such as proximity to ambient contamination sources, were main drivers of PFAS contamination in tap water, while PFAS contamination in house dust was driven mainly by within-home sources. Exposure estimates calculated from the measured PFAS concentrations highlight the importance of addressing potential sources of exposure to PFAS within homes in addition to ambient sources affecting communities’ drinking water, particularly to reduce children’s exposure to these chemicals.

Investigating nuisance dust complaints: Combining high frequency dust deposition records and source identification using integrated microanalytical techniques

While ducted dust emissions from industry are usually well regulated and controlled, fugitive dust emissions can be difficult to quantify or differentiate from off-site emissions, particularly where fugitive emissions are transient or intermittent. In this study, sources of nuisance dust were investigated using a novel dust deposition sampling methodology, followed by chemical and mineralogical analysis using optical microscopy, x-ray diffraction (XRD), scanning electron microscopy with energy dispersive x-ray spectrometry (SEM-EDS), and isotope ratio mass spectrometry analysis. Dust deposition over 24 h was collected on horizontally orientated 300 mm square glass panels at 6 sites in the region of interest. This method captured very small (<10 mg) masses of dust and could distinguish very small variations in dust deposition at different sites and on different days. Comparison samples collected from potential dust sources at a nearby lime manufacturing facility, and other potential fugitive dust sources in the region were differentiated using XRD mineralogy, visual appearance by optical microscopy and SEM-EDS analysis of individual particles. Comparison of selected dust samples to reference samples indicated most dust deposition at the study sites consisted of soil or sand. However, dust deposition at two sites was sometimes composed of a material that was similar in composition to lime that had been rehydrated to portlandite, but not yet fully carbonated to calcite. Subsequent analysis of δ13C and δ18O for selected dust samples from these two sites were consistent with rapid and recent carbonation of small particles in an alkaline environment, which could have occurred during the atmospheric release and transport of lime, and ruled out fugitive dust emission from lime stockpiles existing on site. Combining the information obtained from high frequency record of dust deposition with targeted mineralogical, isotopic and morphological examinations provided new insight into the source of fugitive dust emissions in this area.