Dual-source CT Research Articles

A comparison of computed tomography imaging with histopathology in the sensitivity and correlation of evaluating coronary arterial calcification.

The sensitivity and correlation of coronary computed tomography angiography (CTA) as compared with histopathology are unknown in evaluating coronary arterial calcification. In this study, we retrospectively evaluated qualitatively and quantitatively the sensitivity and correlation of coronary CTA compared with histopathology in assessing coronary arterial calcification. This study was conducted on 12 randomly selected cadavers aged over 40 years at the time of death, and 53 segments of coronary arteries from these 12 cadavers were obtained from the Human Anatomy Laboratory of Tianjin Medical University. The artery segments were scanned using contrasted-enhanced dual-source computed tomography (DSCT) with an axial slice thickness of 0.6 mm. Coronary artery calcification in a coronary segment was defined as the presence of 1 or more voxels with a CT density >130 Hounsfield units. According to the arc of calcification in the cross section of the coronary artery wall, calcified plaques were divided into three categories: mild, moderate, and severe calcification. The coronary artery stenosis caused by calcified plaque was observed and calculated with multiplanar reconstruction (MPR), maximum density projection, volume rendering (VR), and cross-sectional reconstruction. After CT enhancement scanning, the coronary artery specimens were cut into 4-mm long segments and embedded in paraffin for pathological staining. Pathological classification and coronary artery stenosis measured with pathological analysis were used as comparison criteria. Histopathology detected 69 Vb-type plaques, while DSCT detected 57 calcified plaques. The sensitivity of CT for detecting mild, moderate, and severe calcified plaques were 88.3% [95% confidence interval (CI): 74.1-95.6%], 100% (95% CI: 69.8-100%), and 100% (95% CI: 73.2-100%), respectively. DSCT had a significant (P<0.001) correlation with histopathology in quantifying coronary artery stenosis caused by mild, moderate, and severe calcified plaques (R2=0.9278, R2=0.9158, R2=0.7923, respectively). Compared with histopathology, DSCT overestimated coronary artery stenosis caused by mild, moderate, and severe calcified plaques (3.2%±2.0%, 4.9%±4.7%, and 14.7%±8.2%, respectively; P<0.05). DSCT contrast enhancement scanning can detect and characterize coronary artery calcification with a good correlation with histopathologic quantification of coronary artery stenosis caused by different types of calcified plaques, even though coronary CTA may overestimate the stenosis.

Comparison of First-generation and Third-generation Dual-source Computed Tomography for Detecting Coronary Artery Disease in Patients Evaluated for Transcatheter Aortic Valve Replacement.

This study compared image quality and evaluability of coronary artery disease (CAD) in routine preparatory imaging for transcatheter aortic valve replacement using 64-slice (first-generation) to 192-slice (third-generation) dual-source computed tomography(DSCT). The CT data sets of 192 patients (122 women, median age 82y) without severe renal dysfunction or known CAD were analyzed retrospectively. Half were examined using first-generation DSCT (June 2014 to February 2016) and the other half with third-generation DSCT (April 2016 to April 2017). Per protocol, contrast material (110 [110 to 120] vs. 70 [70 to 70]mL, P<0.001) and radiation dose of multiphasic retrospectively gated thoracic CT angiography (dose-length-product, 1001 [707 to 1312] vs. 727 [474 to 1369]mGy×cm, P<0.001) were significantly lower with third-generation DSCT. Significant CAD was defined as CAD-RADS ≥4 by CT. Invasive coronary angiography served as the reference standard (CAD is defined as ≥70% stenosis or fractional flow reserve ≤0.80). In comparison with first-generation DSCT, third-generation DSCT showed significantly better subjective (3 [interquartile range 2 to 3] vs. 4 [3 to 4.25] on a 5-point scale, P<0.001) and objective image quality (signal-to-noise ratio of left coronary artery 12.8 [9.9 to 16.4] vs. 15.2 [12.4 to 19.0], P<0.001). Accuracy (72.9% vs. 91.7%, P=0.001), specificity (59.7% vs. 88.3%, P<0.001), positive (61.0% vs. 83.3%, P<0.001), and negative predictive value (91.9% vs. 98.2%, P=0.045) for detecting CAD per-patient were significantly better using third-generation DSCT, while sensitivity was similar (92.3% vs. 97.2%, P=0.129). Coronary artery evaluation with CT angiography before TAVI is feasible in selected patients. Compared with first-generation DSCT, state-of-the-art third-generation DSCT technology is superior for this purpose, allowing for less contrast medium and radiation dose while providing better image quality and improved diagnostic performance.

Feasibility of Ultra-Low Volume Contrast-Saline Mixture Injection With Dual-Flow Technique in a Pre-TAVI Computed Tomography Angiography.

To explore the feasibility and image quality of ultra-low volume contrast-saline mixture injection with dual-flow injection technique in a computed tomography angiography (CTA) protocol in patients scheduled for transcatheter aortic valve implantation (TAVI). Forty (40) TAVI candidates underwent investigation with CTA using a third-generation dual-source CT scanner between September and November 2020. Different volumes of a monophasic contrast-saline mixture at an 80:20 ratio were administered at an infusion rate of 3 mL/s in 20 patients (group A). The injected volume was based on patient body mass index (BMI): 50 mL if BMI <29 kg/m2 and 63 mL if BMI >29 kg/m2. The other 20 patients (group B)-the control cases-received a total of 65 mL of contrast medium (CM), in multiphasic injections at different flow rates, followed by 10 mL of saline. The images that were obtained were prospectively evaluated for image quality, vessel attenuation (HU), signal-to-noise ratio (SNR), contrast-to-noise ratio (CNR), and estimated radiation dose. Image quality of the aortic root and ilio-femoral vessels was diagnostic in all patients. Vascular attenuation was >200 HU and CNR >3 at any vessel level. Data from this study suggest that a monophasic ultra-low volume contrast-saline mixture injection with a dual-flow technique can provide clear visualisation of the aortic root and ilio-femoral vessels in pre-TAVI CTA, which is comparable with a standard multiphasic volume injection protocol.

Impact of the automatic tube current modulation (ATCM) system on virtual monoenergetic image quality for dual-source CT: A phantom study

PurposeTo assess the impact of the automatic tube current modulation (ATCM) on virtual monoenergetic images (VMIs) quality in dual-source CT(DSCT). Materials and methodsAcquisitions were performed on DSCT using the Mercury phantom. The acquisition parameters for an abdomen-pelvic examination with single-energy CT(SECT) and dual-energy CT(DECT) imaging were used. Acquisitions were performed for each imaging mode using fixed mAs and ATCM. The mAs value was set to obtain a volume CT dose index of 11 mGy in fixed mAs acquisitions. This value was used as the reference mAs in ATCM acquisitions. The noise power spectrum and task-based transfer function at 40,50,60 and 70 keV levels were computed on VMIs and SECT images. The detectability index (d′) was calculated for a lesion with an iodine concentration of 10 mg/mL. ResultsThe noise magnitude on VMIs was higher with the ATCM system than with fixed mAs for all energy levels and section diameters of 21,26 and 31 cm. The noise texture and spatial resolution were similar between the fixed mAs and ATCM acquisitions for both imaging modes. The d’ values were lower for all energy levels with ATCM than with fixed mAs acquisitions for 21 and 26 cm diameters by −39.82 ± 9.32%, similar at 31 cm diameter −4.13 ± 0.24% and higher at 36 cm diameter 10.40 ± 6.69%. It was higher on VMIs at all energy levels compared to SECT images. ConclusionsThe ATCM system could be used with DECT imaging to optimize patient exposure without changing the noise texture and spatial resolution of VMIs compared to fixed mAs and SECT.

Diagnostic value of DECT-based colored collagen maps for the assessment of cruciate ligaments in patients with acute trauma

ObjectivesThe purpose of this study was to evaluate the diagnostic accuracy of third-generation dual-source dual-energy CT (DECT) color-coded collagen reconstructions for the assessment of the cruciate ligaments compared to standard grayscale image reconstruction.MethodsPatients who underwent third-generation dual-source DECT followed by either 3-T MRI or arthroscopy of the knee joint within 14 days between January 2016 and December 2021 were included in this retrospective study. Five radiologists independently evaluated conventional grayscale DECT for the presence of injury to the cruciate ligaments; after 4 weeks, readers re-evaluated the examinations using grayscale images and color-coded collagen reconstructions. A reference standard for MRI was provided by a consensus reading of two experienced readers and arthroscopy. Sensitivity and specificity were the primary metrics of diagnostic performance.ResultsEighty-five patients (mean age, 44 years ± 16; 50 male) with injury to the ACL or PCL (n = 31) were ultimately included. Color-coded collagen reconstructions significantly increased overall sensitivity (94/105 [90%] vs. 67/105 [64%]), specificity (248/320 [78%] vs. 215/320 [67%]), PPV (94/166 [57%] vs. 67/162 [39%]), NPV (248/259 [96%] vs. 215/253 [85%]), and accuracy (342/425 [81%] vs. 282/425 [66%]) for the detection of injury to the anterior cruciate ligament (all parameters, p < .001). For injury to the posterior cruciate ligament, diagnostic accuracy increased for complete tears (p < .001). Color-coded collagen reconstructions achieved superior diagnostic confidence, image quality, and noise scores compared to grayscale CT (all parameters, p < .001) and showed good agreement with MRI examinations.ConclusionsDECT-derived color-coded collagen reconstructions yield substantially higher diagnostic accuracy and confidence for assessing the integrity of the cruciate ligaments compared to standard grayscale CT in patients with acute trauma.Key Points• Color-coded collagen reconstructions derived from dual-energy CT yield substantially higher diagnostic accuracy and confidence for the assessment of the cruciate ligaments compared to standard grayscale CT in patients with acute trauma.• Color-coded collagen reconstructions demonstrate good agreement with MRI for the assessment cruciate ligament injury.• Dual-energy CT may serve as a readily available screening approach for patients with acute trauma to the knee when injury to the cruciate ligaments is suspected.

Analysis of clinical diagnosis and treatment of intestinal volvulus

BackgroundThe aim of this study is to investigate the clinical characteristics and treatment experience of intestinal volvulus, and to analyze the incidence of adverse events and related risk factors of intestinal volvulus.MethodsThirty patients with intestinal volvulus admitted to the Digestive Emergency Department of Xijing Hospital from January 2015 to December 2020 were selected. The clinical manifestations, laboratory tests, treatment and prognosis were retrospectively analyzed.ResultsA total of 30 patients with volvulus were enrolled in this study, including 23 males (76.7%), with a median age of 52 years (33–66 years). The main clinical manifestations were abdominal pain in 30 cases (100%), nausea and vomiting in 20 cases (67.7%), cessation of exhaust and defecation in 24 cases (80%), and fever in 11 cases (36.7%). The positions of intestinal volvulus were jejunum in 11 cases (36.7%), ileum and ileocecal in 10 cases (33.3%), sigmoid colon in 9 cases (30%). All 30 patients received surgical treatment. Among the 30 patients underwent surgery, 11 patients developed intestinal necrosis. We found that the longer the disease duration (> 24 h), the higher the incidence of intestinal necrosis, and the higher the incidence of ascites, white blood cell count and neutrophil ratio in the intestinal necrosis group were significantly higher than those in the non-intestinal necrosis group (p < 0.05). After treatment, 1 patient died of septic shock after operation, and 2 patients with recurrent volvulus were followed up within 1 year. The overall cure rate was 90%, the mortality rate was 3.3%, and the recurrence rate was 6.6%.ConclusionLaboratory examination, abdominal CT and dual-source CT are very important for the diagnosis of volvulus in patients with abdominal pain as the main symptom. Increased white blood cell count, neutrophil ratio, ascites and long course of disease are important for predicting intestinal volvulus accompanied by intestinal necrosis. Early diagnosis and timely intervention can save lives and prevent serious complications.

Optimal dual-energy computed tomography scan parameters to detect small-sized urinary stones and their composition

To investigate the optimal scanning parameters of dual-energy computed tomography (DECT), which can accurately determine sensitivity (the detectability of urinary stones) and accuracy (the composition matching of urinary stones), and to apply them to clinical trials. Fifteen urinary stones were chemically analyzed, and their chemical compositions were considered a reference standard with which we compared the uric acid (UA) and non-UA compositions determined using DECT. The urinary stones were placed inside a bolus and scanned with a dual-source CT scanner under various selected dual-energy conditions (A to X) using various solid water phantom thicknesses. These datasets were analyzed using the Siemens syngo.via software tool (integrated into the CT system) for matching the sensitivity and accuracy assessments. This study showed that 80% of the highest sensitivity (detection of urinary stones) and 92% of the highest accuracy (composition matching of urinary stones) were achieved under condition A (a collimation beam width setting of 2 × 32× 0.6mm, an automatic exposure control setting of 80/sn140 peak kilovoltage, and a slice thickness of 0.5/0.5mm) (P < 0.05). Application of the DECT energy parameters presented in the study will help identify the sensitivity and accuracy of UA and non-UA stone analysis, even in patients with small-sized urinary stones and in conditions difficult for analysis.

Dual-source CT with metal sphere-tube for preoperative evaluation of patients with aortic valve disease treated by transcatheter aortic valve implantation

To predict the effects of Dual-source CT imaging technology for preoperative patients with transcatheter aortic valve implantation. This is a parallel, randomly allocated to following two groups: patients with the Dual-source CT imaging technology and with conventional imaging technology, and the clinical material from two groups patients with Aortic valve disease are collected, and the images quality between two group are assessed and then complications in one month after surgery are recorded by follow-up. Our outcomes show that patients by the Dual-source CT imaging technology show less complications compared to patients by conventional imaging technology and imaging quality is better than that in conventional imaging group. In addition, image noise, and contrast-to-noise ratio are also examined by Dual-source CT imaging. We can conclude that the Dual-source CT can effectively reduce the complications, and the Dual-source CT can predict effects of preoperative patients with Aortic valve disease and prevent the development of Aortic valve disease (AVD).

Coronary computed tomography angiography assessment of relationship between right coronary artery-aorta angle and the development of coronary artery disease.

Whilst a correlation has been established between wide left main coronary artery bifurcation [left anterior descending-left circumflex (LAD-LCx)] angle (>80°) and the development of coronary artery disease (CAD), this retrospective, causal-comparative pilot study aimed to explore whether a relationship exists between right coronary artery (RCA)-aorta angle and CAD. Thirty normal cases were identified via radiology reports and selected as the control group with coronary computed tomography angiography (CCTA) scans performed on a 320-slice computed tomography (CT) scanner. Thirty CAD cases were selected with invasive coronary angiography performed to confirm the degree of stenosis, and CCTA performed on dual source and 320-slice CT scanners. An independent sample t-test was used to compare the differences in coronary angles between the normal and CAD group, and analysis of variance (ANOVA) was used to assess for significant differences between coronary angles in normal and CAD subgroups. Coronary angle measurements were conducted by two independent assessors with high intraclass correlation (r=0.971-0.998, P<0.001). RCA-aorta angle measurements were significantly larger in the normal group [87.47°, 95% confidence interval (CI): 79.31° to 95.78°] compared to the CAD group (76.82°, 95% CI: 67.82° to 85.61°, P=0.05). No significant difference was found between RCA-aorta angle and degree of coronary stenosis (P=0.75). This study suggests a relationship between narrow RCA-aorta angle and CAD.

Visualization and quantification of coconut using advanced computed tomography postprocessing technology.

Computed tomography (CT) is a non-invasive examination tool that is widely used in medicine. In this study, we explored its value in visualizing and quantifying coconut. Twelve coconuts were scanned using CT for three months. Axial CT images of the coconuts were obtained using a dual-source CT scanner. In postprocessing process, various three-dimensional models were created by volume rendering (VR), and the plane sections of different angles were obtained through multiplanar reformation (MPR). The morphological parameters and the CT values of the exocarp, mesocarp, endocarp, embryo, bud, solid endosperm, liquid endosperm, and coconut apple were measured. The analysis of variances was used for temporal repeated measures and linear and non-linear regressions were used to analyze the relationship between the data. The MPR images and VR models provide excellent visualization of the different structures of the coconut. The statistical results showed that the weight of coconut and liquid endosperm volume decreased significantly during the three months, while the CT value of coconut apple decreased slightly. We observed a complete germination of a coconut, its data showed a significant negative correlation between the CT value of the bud and the liquid endosperm volume (y = -2.6955x + 244.91; R2 = 0.9859), and a strong positive correlation between the height and CT value of the bud (y = 1.9576 ln(x) -2.1655; R2 = 0.9691). CT technology can be used for visualization and quantitative analysis of the internal structure of the coconut, and some morphological changes and composition changes of the coconut during the germination process were observed during the three-month experiment. Therefore, CT is a potential tool for analyzing coconuts.

High-Pitch Multienergy Coronary CT Angiography in Dual-Source Photon-Counting Detector CT Scanner at Low Iodinated Contrast Dose.

The aim of this study was to evaluate the high-helical pitch, multienergy (ME) scanning mode of a clinical dual-source photon-counting detector (PCD) computed tomography (CT) and the benefit of virtual monoenergetic images (VMIs) for low-contrast-dose coronary CT angiography (CTA). High-pitch (3.2) ME coronary CTA was performed in PCD-CT in 27 patients using low contrast dose (30 mL of iohexol 350 mg/mL) and in 26 patients at routine contrast dose (60 mL). Low-energy-threshold 120 kV images (also known as T3D images) and 50 kiloelectron volts (50 keV) and 100 kiloelectron volts (100 keV) VMIs were reconstructed using a 1024 × 1024 matrix and 0.6-mm slices. The CT numbers, noise, and contrast-to-noise ratio (CNR) were measured in the ascending aorta (AA), left main coronary artery (LMCA), and distal left anterior descending (LAD) artery. Confidence in grading luminal stenosis with calcific plaque, noncalcific plaque, and stent was evaluated by 2 independent readers on a 0-100 scale (0 the lowest), and a CAD-RADS score was assigned. Image contrast enhancement, sharpness, noise, artifacts, and overall image quality were rated using a 5-point ordinal scale (1 the lowest). The radiation doses (CTDI) in low- and routine-contrast cohorts were 2.5 ± 0.6 mGy and 3.1 ± 1.7 mGy, respectively ( P = 0.12). At all measured locations, the mean CT number was >300 HU in 120 kV (LMCA 382.9 ± 76.2, distal LAD 341.0 ± 53.9, AA 399.5 ± 76.1) and 50 keV images (LMCA 667.5 ± 139.9, distal LAD 578.1 ± 121.5, AA 700.8 ± 142.5) in the low-contrast cohort, with a 96% increase in CT numbers for 50 keV over 120 kV. The CT numbers were significantly higher ( P < 0.0001) in 50 keV than 120 kV and 100 keV VMI. The CNR was also significantly ( P < 0.0001) higher in 50 keV than 120 kV and 100 keV images in all vessels. Confidence in the assessment of luminal stenosis in the presence of calcific plaque was significantly higher ( P = 0.001) with the addition of 100 keV VMI (median score, 100) than using 50 keV alone (median score, 70) and 120 kV (median score, 70) for reader 1, but no significant differences were seen for reader 2 who had same median scores of 100 for all image types. The confidence in the assessment of luminal stenosis within a stent improved with the use of 100 keV images for both readers (reader 1: median scores for 50 + 100 keV = 100, 50 keV = 82.5, 120 kV = 82.5; reader 2: 50 + 100 keV = 100, 50 keV = 90, 120 kV = 90). There were no significant differences in confidence scores for assessment of luminal stenosis from noncalcific plaques for both readers. The reader-averaged qualitative scores for vascular enhancement and overall image quality were significantly higher for 50 keV VMI than for 120 kV images in both low- and routine-contrast dose cohorts. The image sharpness was nonsignificantly higher at 50 keV VMI than 120 kV images, and the artifact score was comparable for 50 keV VMI and 120 kV images. The noise was higher in 50 keV VMI than in 120 kV images. High-pitch ME PCD-CT mode produced diagnostic quality coronary CTA images at low radiation and iodinated contrast doses. The availability of ME VMIs significantly improved the CNR, overall image quality, and confidence in assessment of luminal stenosis in the presence of calcific plaques and stents, and resulted in change of CAD-RADS categories in 9 patients.

Detection and size quantification of pulmonary nodules in ultralow-dose versus regular-dose CT: a comparative study in COPD patients.

To evaluate detectability and semi-automatic diameter and volume measurements of pulmonary nodules in ultralow-dose CT (ULDCT) vs regular-dose CT (RDCT). Fifty patients with chronic obstructive pulmonary disease (COPD) underwent RDCT on 64-multidetector CT (120 kV, filtered back projection), and ULDCT on third-generation dual source CT (100 kV with tin filter, advanced modeled iterative reconstruction). One radiologist evaluated the presence of nodules on both scans in random order, with discrepancies judged by two independent radiologists and consensus reading. Sensitivity of nodule detection on RDCT and ULDCT was compared to reader consensus. Systematic error in semi-automatically derived diameter and volume, and 95% limits of agreement (LoA) were evaluated. Nodule classification was compared by κ statistics. ULDCT resulted in 83.1% (95% CI: 81.0-85.2) dose reduction compared to RDCT (p < 0.001). 45 nodules were present, with diameter range 4.0-25.3 mm and volume range 16.0-4483.0 mm3. Detection sensitivity was non-significant (p = 0.503) between RDCT 88.8% (95% CI: 76.0-96.3) and ULDCT 95.5% (95% CI: 84.9-99.5). No systematic bias in diameter measurements (median difference: -0.2 mm) or volumetry (median difference: -6 mm3) was found for ULDCT compared to RDCT. The 95% LoA for diameter and volume measurements were ±3.0 mm and ±33.5%, respectively. κ value for nodule classification was 0.852 for diameter measurements and 0.930 for volumetry. ULDCT based on Sn100 kV enables comparable detectability of solid pulmonary nodules in COPD patients, at 83% reduced radiation dose compared to RDCT, without relevant difference in nodule measurement and size classification. Pulmonary nodule detectability and measurements in ULDCT are comparable to RDCT.

Cinematic Rendering of Acute Myocardial Infarction.

HomeRadiologyRecently Published PreviousNext Reviews and CommentaryFree AccessImages in RadiologyCinematic Rendering of Acute Myocardial InfarctionXiaoqing Ding , Zhigang GongXiaoqing Ding , Zhigang GongAuthor AffiliationsFrom the Department of Radiology, Shuguang Hospital Affiliated to Shanghai University of Traditional Chinese Medicine, No 528, Zhangheng R. Pudong New Area, Shanghai, 201203, China.Address correspondence to X.D. (email: [email protected]).Xiaoqing Ding Zhigang GongPublished Online:Jan 31 2023https://doi.org/10.1148/radiol.221828MoreSectionsPDF ToolsImage ViewerAdd to favoritesCiteTrack CitationsPermissionsReprints ShareShare onFacebookTwitterLinked In Supplemental material is available for this article.A 43-year-old male patient presented to the emergency department with acute chest pain. The patient condition was stable, and an electrocardiography scan was obtained and showed ST segment changes with troponin I levels of 106.251 ng/mL; however, the patient refused percutaneous catheter intervention. To exclude aortic and pulmonary artery disease, dual-source CT angiography (CTA) of the chest was performed. No aortic or pulmonary artery abnormalities were identified; however, CTA demonstrated suspicious occlusion of left anterior descending coronary artery, focal hypodensity of the anterior wall, and interventricular septum, which is further highlighted with use of cinematic rendering reconstruction technique (Figure, Movie).CT angiography of the chest in a 43-year-old man with acute chest pain. Cinematic rendering of (A) four-chamber heart view and (B) anteroposterior view shows a focal area of decreased attenuation in the myocardium (anterior wall and interventricular septum).Download as PowerPointOpen in Image Viewer Get the Flash Player to see this video.Movie: Cinematic rendering of the heart, show a focal area of decreased attenuation in the myocardium.Download Original Video (20.9 MB)With increasing temporal resolution, it becomes possible to observe changes in myocardial density in the setting of acute myocardial infarction with use of conventional CTA of the chest (1). Cinematic rendering reconstruction technique (2) allows CTA to achieve highly realistic, photograph-level, postprocessed images that show the areas of acute myocardial ischemia more intuitively in three dimensions.Disclosures of conflicts of interest: X.D. No relevant relationships. Z.G. No relevant relationships.

Ultrahigh-resolution computed tomography of the cervical spine without dose penalty employing a cadmium-telluride photon-counting detector

PurposeThis cadaveric study compared image quality between a third-generation dual-source CT scanner with energy-integrating detector technology (EID) and a first-generation CT system employing a photon-counting detector (PCD) for the cervical spine in ultrahigh-resolution mode. MethodsThe cervical spine of eight formalin-fixed full-body cadaveric specimens was scanned with both CT systems using 140 kVp scan protocols matched for CTDIvol (full-dose; low-dose; ultralow-dose; 10 mGy; 3 mGy; 1 mGy). Images were reconstructed with 1 mm slice thickness and 0.5 mm increment. Three radiologists rated overall subjective image quality based on an equidistant five-point scale with the intraclass correlation coefficient (ICC) calculated for assessment of interobserver reliability. Contrast-to-noise ratios were calculated individually for bone (CNRbone) and muscle tissue (CNRmuscle) to provide objective criteria of image analysis. ResultsSubjective image quality, as well as CNRbone, and CNRmuscle were each superior for PCD-CT compared to EID-CT among dose-matched scan protocol pairs (all p < 0.05). Between full-dose EID-CT and low-dose PCD-CT, subjective image quality was equal (p = 0.903), while superior quantitative results regarding the latter were ascertained (both p < 0.001). Similarly, objective analysis determined higher CNRbone, and CNRmuscle in ultralow-dose PCD-CT compared to low-dose EID-CT (both p < 0.001), while readers considered the image quality of the respective studies comparable (p > 0.99). Interobserver reliability was good, denoted by an ICC of 0.861 (95 % confidence interval: 0.788 – 0.914; p < 0.001). ConclusionsIn cervical spine examinations, both subjective and objective image quality of PCD-CT were superior to EID-CT in comparison of scan protocols with corresponding dose levels, suggesting potential for significantly reducing the radiation exposure without compromising image quality.

Value of dual-source CT dual-energy parameters combined with serum detection of VEGF and CEA in the diagnosis of early lung cancer

ABSTRACT To discuss the value of dual-source CT dual-energy parameters combined with serum detection of vascular endothelial growth factor (VEGF) and carcinoembryonic antigen (CEA) in the diagnosis of early lung cancer (LC). In total, 100 patients with lung lesions in our hospital from January 2020 to January 2022 were selected for retrospective study, and were divided into the lung cancer group (group A) and benign lung disease group (group B) according to the final results of pathological diagnosis, using dual-source CT dual-energy scanning combined with serum detection of VEGF and CEA to analyze the diagnostic values of single detection and combined detection. Among the 100 patients with lung lesions, there were 58 patients with LC and 42 patients with benign lung diseases after pathological examination, with no statistical difference in normalized iodine concentration (NIC) and the increased value of iodine at arterial phase between the two groups (P > 0.05). The NIC value of group A was higher than group B at venous phase (P < 0.05). The serum levels of VEGF and CEA in group A were higher than group B (P < 0.05). The area under the curve, specificity, sensitivity, Youden index and 95% CI of combined diagnosis were higher than single detection of NIC, VEGF and CEA at venous phase. The combined application of dual-source CT dual-energy parameters and serum detection of VEGF and CEA has higher diagnostic value in patients with early LC, which can provide effective reference for clinical diagnosis and treatment, with higher application value in clinic.

Observer Sensitivity for Detection of Pulmonary Nodules in Ultra-Low Dose Computed Tomography Protocols Using a Third-Generation Dual-Source CT with Ultra-High Pitch—A Phantom Study

This study evaluates ultra-low-dose computed tomography (ULDCT) protocols concerning the detectability of pulmonary nodules. The influence of tube current settings, kernels, strength levels of third-generation iterative reconstruction algorithms, and pitch was investigated. A chest phantom with artificial spherical nodules of different densities and diameters was examined with a third-generation dual-source CT. Scanning and post-processing protocols, tube current levels, and ultra-high and non-high pitch modes were applied. Images were reconstructed with filtered back-projection (FBP) or advanced model-based iterative reconstruction (ADMIRE) algorithms. Sharp (Bl57) or medium-soft (Br36) convolution kernels were applied. The reading was performed by an experienced and an inexperienced reader. The highest observer sensitivity was found using a non-high pitch protocol at tube currents of 120 mAs and 90 mAs with the sharp kernel and iterative reconstruction level of 5. Non-high pitch protocols showed better detectability of solid nodules. Combinations with the medium-soft kernel achieved slightly higher observer sensitivity than with the sharp kernel. False positives (FP) occurred more often for subsolid nodules, at a tube current level of 120 mAs, and with the sharp kernel. A tube current level of 90 mAs combined with the highest iterative reconstruction level achieved the highest accuracy in lung nodule detection regardless of size, density, and reader experience.

Questions about "Intra-atrial right coronary artery on dual-source CT"

Questions about "Intra-atrial right coronary artery on dual-source CT"

Assessment of Intracardiac and Extracardiac Deformities in Patients with Various Types of Pulmonary Atresia by Dual-Source Computed Tomography

Background: Pulmonary atresia (PA) is a group of heterogeneous complex congenital heart disease. Only one study modality might not get a correct diagnosis. This study aims to investigate the diagnostic power of dual-source computed tomography (DSCT) for all intracardiac and extracardiac deformities in patients with PA compared with transthoracic echocardiography (TTE). Materials and Methods: This retrospective study enrolled 79 patients and divided them into three groups according to their main diagnosis. All associated malformations and clinical information, including treatments, were recorded and compared among the three groups. The diagnostic power of DSCT and TTE on all associated malformations were compared. The surgical index (McGoon ratio, pulmonary arterials index (PAI), and total neopulmonary arterial index) and radiation dose were calculated on the basis of DSCT. Results: Of the patients, 32, 30, and 17 were divided into the groups of PA with ventricular septal defect (VSD), PA with VSD and major aortopulmonary collateral arteries, and PA with other major malformations, respectively. Consequently, 182, 162, and 13 intracardiac, extracardiac, and other major malformations were diagnosed, respectively. Moreover, DSCT showed a better diagnostic performance in extracardiac deformities (154 vs. 117, p < 0.001), whereas TTE could diagnose intracardiac deformities better (159 vs. 139, p = 0.001). The McGoon ratio, PAI, and treatment methods were significantly different among the three groups (p = 0.014, p = 0.008, and p = 0.018, respectively). Conclusion: More than one imaging modality should be used to make a correct diagnosis when clinically suspecting PA. DSCT is superior to TTE in diagnosing extracardiac deformities and could be used to roughly calculate surgical indices to optimize treatment strategy.

Application of Dual-Source CT Using Iterative Reconstruction Technology Combined with CT-FFR Parameters in the Diagnosis of Coronary Heart Disease.

In order to achieve early detection of myocardial ischemia and improve the diagnosis of coronary heart disease (CHD), it is necessary to find a convenient, non-invasive and effective examination method. This study aimed to explore the application value of dual-source computed tomography (CT) by using advanced modeled iterative reconstruction (ADMIRE) combined with computed tomography-fractional flow reserve (CT-FFR) technique in CHD, which provides imaging basis for early diagnosis of CHD and myocardial ischemia. Seventy-five CHD patients were examined by coronary computed tomography angiography (CCTA). Their CCTA images were reconstructed by iterative algorithm in ADMIRE 1-5 using post-processing workstation. The standard deviation (SD), signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR) of proximal vascular images in right coronary artery (RCA), left main coronary artery (LM), left anterior descending artery (LAD) and left circumflex artery (LCX) were analyzed and compared. Invasive coronary angiography (ICA) was adopted in patients with ≥50% stenosis of coronary artery diameter. Taking ICA as the gold-standard method to accurately assess coronary arterial stenosis degree, the diagnostic efficiency of dual-source CT to diagnose coronary artery stenosis was analyzed. Some patients were subjected to myocardial CT perfusion (CTP) scanning and CT-FFR analysis, which facilitated analyzing the correlation and consistency between the diagnostic results of CTP and analysis results of CT-FFR. There was no statistical difference in the CT values of RCA, LM, LAD and LCX in groups with different ADMIRE reconstruction intensities (p > 0.05). But the noise, SNR and CNR interval were different among the iterative intensity groups (p < 0.05). Kappa consistency analysis was used to analyze the subjective evaluation results of image quality under different iterative reconstruction grades. The independent sample t-test performed on the subjective scores revealed that the scores on images were the best at ADMIRE 4. CCTA has sensitivity, specificity, positive predictive value, and negative predictive value of 91.52%, 97.59%, 97.98%, and 96.42% for identifying coronary artery stenosis, respectively. The diagnostic efficacy of CT-FFR, the Kappa analysis of myocardial CTP and CT-FFR results, which yields a Kappa value of 0.830 (p < 0.05). Spearman correlation analysis was used to statistically analyze the results of myocardial CTP and CT-FFR (correlation coefficient r = 0.774, p < 0.05). Diagnostic sensitivity and specificity were 93% and 95%, respectively. The dual-source CT using ADMIRE iterative algorithm has the best display of coronary vessels and higher image quality when the intensity is 4, and CT-FFR can be used as a non-invasive method for early detection of myocardial ischemia, which is worthy of clinical application.

Copeptin Reflect Left Ventricular Systolic Function at Early Stage of Acute Myocardial Infarction in a Pig Model.

Measurement of biomarkers early after acute myocardial infarction (AMI) might provide a cost-effective and widely available tool to assess infarct severity, myocardial dysfunction, and clinical outcomes. We aimed to induce AMI in miniature pigs, measure the levels of serum biomarkers and global LV function dynamically and explore the release kinetics and optimal sampling time points of copeptin and its correlation with global LV function. We induced AMI in the experimental group using a closed-chest model. Left ventricular (LV) function was detected by dual-source computed tomography (DSCT) and serum copeptin was determined by ELISA. The serum copeptin levels were increased at 1 hour, peaked at 3 hours, gradually decreased after 6 hours, and returned to baseline 3 days after AMI. At 3 to 6 hours, the copeptin cutoff of 16.97 to 17.44 pmol/l had 100% sensitivity and 100% specificity (P ⩽ .001) for AMI. Serum copeptin levels at 3 hours and 3 days were negatively correlated with the 3-hours LVEF (P ⩽ .001), respectively. Serum copeptin levels change in time, and measurements at 3 to 6 hours after AMI had the highest predictive value.