Dual-inlet Isotope Ratio Mass Spectrometry Research Articles

Affordable event and monthly rain samplers: Improving isotopic datasets to understand meteorological processes.

Water-stable isotopes in rainfall are powerful tracers of atmospheric processes at different spatial and temporal scales. However, commercially available rain samplers for isotopic analysis are prohibitively expensive, especially for high spatial resolution networks and studies conducted in developing countries. A low-cost, simple, and robust sampler was designed for event and monthly rainfall samplings. Rainfall collectors were built based on existing designs provided in the literature and using easily accessible materials. Event samplers were filled with different volumes of reference water and left for 72 h in laboratory conditions to determine the minimum amount of rainfall to be collected to minimize isotopic fractionation, from both postsampling evaporation and equilibration. Samples were analyzed using dual-inlet isotope ratio mass spectrometry and cavity ring-down spectroscopy. For samples larger than 4% of the bottle's capacity, the evaporative enrichment due to Rayleigh distillation is negligible compared to the overall analytical uncertainty. Using a tube connecting the funnel to the water sample has proved to reduce postsampling evaporation by at least five times. To limit water self-diffusion, we recommend collecting the largest rainfall amount possible. Under these conditions, these collectors are suitable for rainfall sampling for isotopic analysis. This low-cost methodology will enable isotopic sampling of precipitation at high spatial resolutions and democratize the use of isotopes for hydrological studies in developing countries. All instructions for building and using these samplers are made openly accessible to the scientific community so they can be repeated and adapted to the needs of each project.

Physical model for multi-point normalization of dual-inlet isotope ratio mass spectrometry data.

A simple model is presented for multi-point normalization of dual-inlet isotope ratio mass spectrometry (DI-IRMS) data. The model incorporates the scale contraction coefficient and the normalized working reference gas isotope delta value as its two physical parameters. The model allows the full use of isotope measurement data and outputs the normalized sample isotope delta value along with the mentioned parameters. The model reduces to the expected linear behavior on application to a natural range CO2 isotopic composition sample, under typically observed scale contraction levels. Next, DI-IRMS measurements of the NIST CO2 gas isotopic reference materials (RMs) 8562, 8563, and 8564 are used to construct a three-point linear calibration, spanning 40‰ for the [Formula: see text] and 20‰ for the [Formula: see text] raw data. Accuracy of the regression at the 0.009‰ level for [Formula: see text] and 0.01‰ for [Formula: see text] is observed for the three NIST RMs. The model derived scale contraction term is found to be a more accurate measure of cross-contamination in contrast to its end of day measurements by the enriched sample method. The constructed multi-point normalization model is next used to assign [Formula: see text] and [Formula: see text] isotope delta values on the Vienna PeeDee Belmnite-CO2 (VPDB-CO2) scale, for pure CO2 gas samples in the natural isotopic range. A Monte Carlo analysis of the uncertainty, including estimates for the normalization step, is provided to assist future multi-point normalization with more than three reference points.

Review on Applications of 17O in Hydrological Cycle.

The triple oxygen isotopes (16O, 17O, and 18O) are very useful in hydrological and climatological studies because of their sensitivity to environmental conditions. This review presents an overview of the published literature on the potential applications of 17O in hydrological studies. Dual-inlet isotope ratio mass spectrometry and laser absorption spectroscopy have been used to measure 17O, which provides information on atmospheric conditions at the moisture source and isotopic fractionations during transport and deposition processes. The variations of δ17O from the developed global meteoric water line, with a slope of 0.528, indicate the importance of regional or local effects on the 17O distribution. In polar regions, factors such as the supersaturation effect, intrusion of stratospheric vapor, post-depositional processes (local moisture recycling through sublimation), regional circulation patterns, sea ice concentration and local meteorological conditions determine the distribution of 17O-excess. Numerous studies have used these isotopes to detect the changes in the moisture source, mixing of different water vapor, evaporative loss in dry regions, re-evaporation of rain drops during warm precipitation and convective storms in low and mid-latitude waters. Owing to the large variation of the spatial scale of hydrological processes with their extent (i.e., whether the processes are local or regional), more studies based on isotopic composition of surface and subsurface water, convective precipitation, and water vapor, are required. In particular, in situ measurements are important for accurate simulations of atmospheric hydrological cycles by isotope-enabled general circulation models.

Interlaboratory test for stable carbon isotope analysis of dissolved inorganic carbon in geothermal fluids.

Stable carbon isotope ratios have many applications in natural sciences. In the first worldwide interlaboratory proficiency test, the discrepancies in measured δ13 CDIC values of natural waters were up to σ = ±3‰. Therefore, we continued the investigation on the analytical data quality assurance of individual laboratories and internal consistency among laboratories worldwide. We designed and performed an interlaboratory comparison exercise for δ13 C analyses of ten water and two solid samples (Na2 CO3 , CaCO3 ), including two synthetic samples prepared by dissolving the carbonates individually. Three laboratories analyzed an additional sample set to assess solution stability, at least one month after the first set analysis period. The δ13 C values were measured using dual inlet isotope ratio mass spectrometry (DI-IRMS) or continuous flow (CF)-IRMS. The δ13 C values of solid Na2 CO3 and its aqueous solution were -5.06 ± 0.21‰ and 5.32 ± 0.24‰, respectively, while the δ13 C value of solid CaCO3 was -4.49 ± 0.93‰. Similarly, the lake water has a consistent value (2.45 ± 0.19‰). The δ13 C values of geothermal water have a wide dispersion among individual laboratory measurements and among those of different laboratories; however, a trend exists in the δ13 C values measured at the three sampling points of each well. The δ13 C values of solid Na2 CO3 and its solution, and lake water (i.e. DIC concentration samples >100 mg/L carbon) are consistent among all the participating laboratories. The dispersion in the δ13 C values of solid CaCO3 is associated with its lower chemical affinity than that of Na2 CO3 . The poor reproducibility in the δ13 C values of geothermal fluids, collected at three points of a geothermal well, despite overall consistent trends regarding their collection points suggests inadequate sample handling (atmospheric CO2 exchange) and/or inappropriate analytical approaches (incomplete H3 PO4 acid reaction).

A rapid method for determination of the hydrogen isotopes of H2 O in micro-inclusions by chromium-filled elemental analyzer/isotope ratio mass spectrometry.

The study of hydrogen isotopes in fluid inclusions is of great significance in the evolution of ore deposits, speleothem research and fluid migration. Conventional analysis methods are based on off-line thermal decrepitation or mechanical crushing followed by dual-inlet isotope ratio mass spectrometry (DI-IRMS). Because a large sample size (at least 1 g) is required for the conventional methods, the hydrogen isotope analysis of small-sized quartz samples is challenging. A method for the hydrogen isotope analysis of H2 O from fluid inclusions in minerals using a Cr-EA/IRMS method (a single-oven, chromium-filled elemental analyzer coupled to IRMS) is presented. The reactor is filled with chromium reagent instead of glassy carbon chips, which allows quantitative conversion of the H2 O in quartz inclusions into H2 for the first time. The hydrogen isotope ratio is then determined by continuous-flow IRMS. Eight quartz samples were analyzed using the Cr-EA/IRMS method. The hydrogen isotope ratios obtained using this method were consistent with those obtained using the off-line method. For small samples of less than 20 mg, the δ2 H values showed large variance (6-15‰), suggesting that the results were significantly influenced by the background. In contrast, the reproducibility of the δ2 H values for samples of more than 20 mg was better than 3‰. The proposed Cr-EA/IRMS method greatly reduces the minimum sample size (to ca 20 mg) and the laboratory time (30 samples each day) without compromising precision compared with the off-line method. The method offers a reliable and economic approach for measuring the δ2 H values of geological samples.

Precise determination of Ar, Kr and Xe isotopic fractionation due to diffusion and dissolution in fresh water

Dissolved noble gases are ideal conservative tracers of physical processes in the Earth system due to their chemical and biological inertness. Although bulk concentrations of dissolved Ar, Kr, and Xe are commonly measured to constrain physical models of atmosphere, ocean, and terrestrial hydrosphere processes, stable isotope ratios of these gases (e.g. 136Xe/129Xe) are seldom used because of low signal-to-noise ratios. Here we present the first results from a new method of dissolved gas sampling, extraction and analysis that permits measurement of stable Ar, Kr, and Xe isotope ratios at or below ∼5 per meg amu−1 precision (1σ), two orders-of-magnitude below conventional Kr and Xe isotopic measurements. This gain in precision was achieved by quantitative extraction and subsequent purification of dissolved noble gases from 2-L water samples via helium sparging and viscous dual-inlet isotope ratio mass spectrometry. We have determined the solubility fractionation factors (αsol) for stable Ar, Kr, and Xe isotope ratios between ∼2 and 20°C via laboratory equilibration experiments. We have also conducted temperature-controlled air-water gas exchange experiments to estimate the kinetic fractionation factors (αkin) of these isotope ratios. We find that both αsol and αkin, normalized by isotopic mass difference (Δm), decrease in magnitude with atomic number but are proportional to Δm for isotope ratios of the same element. With the new ability for high precision isotopic measurements, we suggest that dissolved Kr and Xe isotope ratios in groundwater represent a promising, novel geochemical tool with important applications for groundwater modeling, water resource management, and paleoclimate.

Inter-laboratory test for oxygen and hydrogen stable isotope analyses of geothermal fluids: Assessment of reservoir fluid compositions.

Knowledge of the accuracy and precision for oxygen (δ18 O values) and hydrogen (δ2 H values) stable isotope analyses of geothermal fluid samples is important to understand geothermal reservoir processes, such as partial boiling-condensation and encroachment of cold and reinjected waters. The challenging aspects of the analytical techniques for this specific matrix include memory effects and higher scatter of delta values with increasing total dissolved solids (TDS) concentrations, deterioration of Pt-catalysts by dissolved/gaseous H2 S for hydrogen isotope equilibration measurements and isotope salt effects that offset isotope ratios determined by gas equilibration techniques. An inter-laboratory comparison exercise for the determination of the δ18 O and δ2 H values of nine geothermal fluid samples was conducted among eleven laboratories from eight countries (CeMIEGeo2017). The delta values were measured by dual inlet isotope ratio mass spectrometry (DI-IRMS), continuous flow IRMS (CF-IRMS) and/or laser absorption spectroscopy (LAS). Moreover, five of these laboratories analyzed an additional sample set at least one month after the analysis period of the first set. Statistical evaluation of all the results was performed to obtain the expected isotope ratios of each sample, which were then subsequently used in deep reservoir fluid composition calculations. The overall analytical precisions of the measurements were ± 0.2‰ for δ18 O values and ± 2.0‰ for δ2 H values within the 95% confidence interval. The measured and calculated δ18 O and δ2 H values of water sampled at the weir box, separator and wellhead of geothermal wells suggest the existence of hydrogen and oxygen isotope-exchange equilibrium between the liquid and vapor phases at all sampling points in the well. Thus, both procedures for calculating the isotopic compositions of the deep geothermal reservoir fluid - using either the analytical data of the liquid phase at the weir box together with those of vapor at the separator or the analytical data of liquid and vapor phases at the separator -are equally valid.

Preliminary assessment of stable nitrogen and oxygen isotopic composition of USGS51 and USGS52 nitrous oxide reference gases and perspectives on calibration needs.

Despite a long history and growing interest in isotopic analyses of N2 O, there is a lack of isotopically characterized N2 O isotopic reference materials (standards) to enable normalization and reporting of isotope-delta values. Here we report the isotopic characterization of two pure N2 O gas reference materials, USGS51 and USGS52, which are now available for laboratory calibration (https://isotopes.usgs.gov/lab/referencematerials.html). A total of 400 sealed borosilicate glass tubes of each N2 O reference gas were prepared from a single gas filling of a high vacuum line. We demonstrated isotopic homogeneity via dual-inlet isotope-ratio mass spectrometry. Isotopic analyses of these reference materials were obtained from eight laboratories to evaluate interlaboratory variation and provide preliminary isotopic characterization of their δ15 N, δ18 O, δ15 Nα , δ15 Nβ and site preference (SP ) values. The isotopic homogeneity of both USGS51 and USGS52 was demonstrated by one-sigma standard deviations associated with the determinations of their δ15 N, δ18 O, δ15 Nα , δ15 Nβ and SP values of 0.12 mUr or better. The one-sigma standard deviations of SP measurements of USGS51 and USGS52 reported by eight laboratories participating in the interlaboratory comparison were 1.27 and 1.78 mUr, respectively. The agreement of isotope-delta values obtained in the interlaboratory comparison was not sufficient to provide reliable accurate isotope measurement values for USGS51 and USGS52. We propose that provisional values for the isotopic composition of USGS51 and USGS52 determined at the Tokyo Institute of Technology can be adopted for normalizing and reporting sample data until further refinements are achieved through additional calibration efforts.

Metrology for stable isotope reference materials: 13C/12C and 18O/16O isotope ratio value assignment of pure carbon dioxide gas samples on the Vienna PeeDee Belemnite-CO2 scale using dual-inlet mass spectrometry.

Isotope ratio measurements have been conducted on a series of isotopically distinct pure CO2 gas samples using the technique of dual-inlet isotope ratio mass spectrometry (DI-IRMS). The influence of instrumental parameters, data normalization schemes on the metrological traceability and uncertainty of the sample isotope composition have been characterized. Traceability to the Vienna PeeDee Belemnite(VPDB)-CO2 scale was realized using the pure CO2 isotope reference materials(IRMs) 8562, 8563, and 8564. The uncertainty analyses include contributions associated with the values of iRMs and the repeatability and reproducibility of our measurements. Our DI-IRMS measurement system is demonstrated to have high long-term stability, approaching a precision of 0.001 parts-per-thousand for the 45/44 and 46/44 ion signal ratios. The single- and two-point normalization bias for the iRMs were found to be within their published standard uncertainty values. The values of 13C/12C and 18O/16O isotope ratios are expressed relative to VPDB-CO2 using the [Formula: see text] and [Formula: see text] notation, respectively, in parts-per-thousand (‰ or per mil). For the samples, value assignments between (-25 to +2) ‰ and (-33 to -1) ‰ with nominal combined standard uncertainties of (0.05, 0.3) ‰ for [Formula: see text] and [Formula: see text], respectively were obtained. These samples are used as laboratory reference to provide anchor points for value assignment of isotope ratios (with VPDB traceability) to pure CO2 samples. Additionally, they serve as potential parent isotopic source material required for the development of gravimetric based iRMs of CO2 in CO2-free dry air in high pressure gas cylinder packages at desired abundance levels and isotopic composition values. Graphical abstract CO2 gas isotope ratio metrology.

Rapid and high-resolution stable isotopic measurement of biogenic accretionary carbonate using an online CO2 laser ablation system: Standardization of the analytical protocol.

The elaborate sampling and analytical protocol associated with conventional dual-inlet isotope ratio mass spectrometry has long hindered high-resolution climate studies from biogenic accretionary carbonates. Laser-based on-line systems, in comparison, produce rapid data, but suffer from unresolvable matrix effects. It is, therefore, necessary to resolve these matrix effects to take advantage of the automated laser-based method. Two marine bivalve shells (one aragonite and one calcite) and one fish otolith (aragonite) were first analysed using a CO2 laser ablation system attached to a continuous flow isotope ratio mass spectrometer under different experimental conditions (different laser power, sample untreated vs vacuum roasted). The shells and the otolith were then micro-drilled and the isotopic compositions of the powders were measured in a dual-inlet isotope ratio mass spectrometer following the conventional acid digestion method. The vacuum-roasted samples (both aragonite and calcite) produced mean isotopic ratios (with a reproducibility of ±0.2 ‰ for both δ18 O and δ13 C values) almost identical to the values obtained using the conventional acid digestion method. As the isotopic ratio of the acid digested samples fall within the analytical precision (±0.2 ‰) of the laser ablation system, this suggests the usefulness of the method for studying the biogenic accretionary carbonate matrix. When using laser-based continuous flow isotope ratio mass spectrometry for the high-resolution isotopic measurements of biogenic carbonates, the employment of a vacuum-roasting step will reduce the matrix effect. This method will be of immense help to geologists and sclerochronologists in exploring short-term changes in climatic parameters (e.g. seasonality) in geological times.

Measurements of Electron Partitioning Between Cytochrome and Alternative Oxidase Pathways in Plant Tissues.

Plant respiration is characterized by the existence of the alternative oxidase pathway (AOP) that competes with cytochrome oxidase pathway (COP) for the electrons of the ubiquinone pool of the mitochondrial electron transport chain, thus reducing ATP synthesis. The oxygen (O2) isotope fractionation technique is the only available to determine the electron partitioning between the two pathways and their in vivo activities in plant tissues. In this chapter, the basis of the O2 isotope fractionation technique and its derived calculations are carefully explained together with a detailed description of the dual-inlet isotope ratio mass spectrometry (DI-IRMS) system and the protocol developed at the University of Balearic Islands. The key advantages of the DI-IRMS over other systems are highlighted as well as the potential problems of this technique. Among these problems, those associated with leakage, diffusion, and inhibitor treatments are noted and solutions to prevent, detect, and repair these problems are detailed.

A new organic reference material, l-glutamic acid, USGS41a, for δ(13) C and δ(15) N measurements - a replacement for USGS41.

The widely used l-glutamic acid isotopic reference material USGS41, enriched in both (13) C and (15) N, is nearly exhausted. A new material, USGS41a, has been prepared as a replacement for USGS41. USGS41a was prepared by dissolving analytical grade l-glutamic acid enriched in (13) C and (15) N together with l-glutamic acid of normal isotopic composition. The δ(13) C and δ(15) N values of USGS41a were directly or indirectly normalized with the international reference materials NBS 19 calcium carbonate (δ(13) CVPDB = +1.95 mUr, where milliurey = 0.001 = 1 ‰), LSVEC lithium carbonate (δ(13) CVPDB = -46.6 mUr), and IAEA-N-1 ammonium sulfate (δ(15) NAir = +0.43 mUr) and USGS32 potassium nitrate (δ(15) N = +180 mUr exactly) by on-line combustion, continuous-flow isotope-ratio mass spectrometry, and off-line dual-inlet isotope-ratio mass spectrometry. USGS41a is isotopically homogeneous; the reproducibility of δ(13) C and δ(15) N is better than 0.07 mUr and 0.09 mUr, respectively, in 200-μg amounts. It has a δ(13) C value of +36.55 mUr relative to VPDB and a δ(15) N value of +47.55 mUr relative to N2 in air. USGS41 was found to be hydroscopic, probably due to the presence of pyroglutamic acid. Experimental results indicate that the chemical purity of USGS41a is substantially better than that of USGS41. The new isotopic reference material USGS41a can be used with USGS40 (having a δ(13) CVPDB value of -26.39 mUr and a δ(15) NAir value of -4.52 mUr) for (i) analyzing local laboratory isotopic reference materials, and (ii) quantifying drift with time, mass-dependent isotopic fractionation, and isotope-ratio-scale contraction for isotopic analysis of biological and organic materials. Published in 2016. This article is a U.S. Government work and is in the public domain in the USA.

A new isotopic reference material for stable hydrogen and oxygen isotope-ratio measurements of water - USGS50 Lake Kyoga Water.

As a result of the need for isotopic reference waters having high δ(2) HVSMOW-SLAP and δ(18) OVSMOW-SLAP values for daily use, especially for tropical and equatorial-zone freshwaters, a new secondary isotopic reference material for international distribution was prepared from water collected from Lake Kyoga, Uganda. This isotopic reference lakewater was filtered through a membrane with 0.2-µm pore size, homogenized, loaded into glass ampoules that were sealed with a torch and autoclaved to eliminate biological activity, and measured by dual-inlet isotope-ratio mass spectrometry. This reference material is available in a case of 144 glass ampoules each containing 5 mL of water. The δ(2) H and δ(18) O values of this reference material are +32.8 ± 0.4 and +4.95 ± 0.02 mUr (milliurey = 0.001 = 1 ‰), respectively, relative to VSMOW, on scales normalized such that the δ(2) H and δ(18) O values of SLAP reference water are, respectively, -428 and -55.5 mUr. Each uncertainty is an estimated expanded uncertainty (U = 2uc ) about the reference value that provides an interval that has about a 95 % probability of encompassing the true value. This isotopic reference material, designated as USGS50, is intended as one of two reference waters for daily normalization of stable hydrogen and oxygen isotopic analysis of water with an isotope-ratio mass spectrometer or a laser absorption spectrometer, of use especially for isotope-hydrology laboratories analyzing freshwater samples from equatorial and tropical regions.

Improvement of analytical method for chlorine dual‐inlet isotope ratio mass spectrometry of organochlorines

The development of compound-specific chlorine isotope analysis (Cl-CSIA) is hindered by the lack of international organochlorine reference materials with isotopic compositions expressed in the δ(37) Cl notation. Thus, a reliable off-line analytical method is needed, allowing direct comparison of the δ(37) Cl values of molecularly different organic compounds with that of ocean-water chloride, to refer measurement results to a Standard Mean Ocean Chloride (SMOC) scale. The analytical method included sealed-tube combustion of organochlorines, precipitation and subsequent conversion of formed inorganic chlorides into methyl chloride (CH3 Cl) for the determination of δ(37) Cl values by Dual-Inlet Isotope Ratio Mass Spectrometry (DI-IRMS). A sample preparation step most sensitive to the sample size - dissolution of the inorganic copper chlorides formed by combustion of organochlorines - was identified. Recovery of 94 ± 5% of chlorine was reached by applying determined optimal conditions for the dissolution, implying good external precision of δ(37) Cl values (-0.18 ± 0.03‰, 1σ, n = 3). Validation of the optimized method by the analysis of the produced and initial CH3 Cl samples with known δ(37) Cl values vs SMOC resulted in a difference of 0.11 ± 0.04‰ (1σ, n = 3), confirming the external precision and accuracy of the entire method. The efficiency of the sample preparation method for CH3 Cl-DI-IRMS analysis is independent both of the chemical structure of the chlorinated compound and of the amount of chlorine in the sample. This method has the potential to be applied to a broad range of chlorinated organic compounds, e.g. reference material for the calibration of methods for Cl-CSIA against SMOC.

Fractional cholesterol absorption measurements in humans: determinants of the blood-based dual stable isotope tracer technique.

The flux of absorbed cholesterol is a controlling element in the regulation of cholesterol biosynthesis and catabolism. A review of 5 published methods to measure cholesterol absorption is presented, including 2 dual stable isotope approaches. The continuous dual isotope feeding procedure is accurate, but only suitable for small-scale studies. The blood-based dual stable isotope technique is the least invasive and complex procedure, but leads to large variations in individual (<10%->90%) and mean population values (24%-70%) for healthy subjects. The results may be partly determined by the experimental and analytical procedures. Fifteen blood-based dual stable isotope studies published between 1993 and 2013 have been analyzed. The results were related to the methodologies applied and evidence was sought for accordance to the test principles. Seven different isotopic tracers, 3 cholesterol subcompartments in blood, and 6 mass spectrometry techniques were applied. The oral and intravenous test formulations were presented in only 1 study. Time points for blood sampling and methodologies for blood sample preparation and analysis were highly variable. No definite proofs were supplied for the fates of the oral and intravenous cholesterol tracers. Isotope enrichment measurements in free and total cholesterol in plasma and erythrocytes were never compared. Fractional cholesterol absorption rate values depend strongly on the mass spectrometry methodology. Dual-inlet isotope ratio mass spectrometry appears to be the method of choice. Dual stable isotope approaches require validation and standardization of administration and analysis procedures. A control group must always be included to correct for methodological differences.

Biscayne aquifer drinking water (USGS45): a new isotopic reference material for δ2H and δ18O measurements of water.

As a result of the scarcity of isotopic reference waters for daily use, a new secondary isotopic reference material for international distribution has been prepared from drinking water collected from the Biscayne aquifer in Ft. Lauderdale, Florida. This isotopic reference water was filtered, homogenized, loaded into glass ampoules, sealed with a torch, autoclaved to eliminate biological activity, and measured by dual-inlet isotope-ratio mass spectrometry. This reference material is available by the case of 144 glass ampoules containing either 4 mL or 5 mL of water in each ampoule. The δ(2)H and δ(18)O values of this reference material are -10.3 ± 0.4‰ and -2.238 ± 0.011‰, respectively, relative to VSMOW, on scales normalized such that the δ(2)H and δ(18)O values of SLAP reference water are, respectively, -428 and -55.5‰. Each uncertainty is an estimated expanded uncertainty (U = 2uc ) about the reference value that provides an interval that has about a 95% probability of encompassing the true value. This isotopic reference material, designated as USGS45, is intended as one of two isotopic reference waters for daily normalization of stable hydrogen and oxygen isotopic analysis of water with an isotope-ratio mass spectrometer or a laser absorption spectrometer. Published in 2014. This article is a U.S. Government work and is in the public domain in the USA.

Calibrated high-precision &amp;lt;sup&amp;gt;17&amp;lt;/sup&amp;gt;O-excess measurements using cavity ring-down spectroscopy with laser-current-tuned cavity resonance

Abstract. High-precision analysis of the 17O / 16O isotope ratio in water and water vapor is of interest in hydrological, paleoclimate, and atmospheric science applications. Of specific interest is the parameter 17O excess (Δ17O), a measure of the deviation from a~linear relationship between 17O / 16O and 18O / 16O ratios. Conventional analyses of Δ17O of water are obtained by fluorination of H2O to O2 that is analyzed by dual-inlet isotope ratio mass spectrometry (IRMS). We describe a new laser spectroscopy instrument for high-precision Δ17O measurements. The new instrument uses cavity ring-down spectroscopy (CRDS) with laser-current-tuned cavity resonance to achieve reduced measurement drift compared with previous-generation instruments. Liquid water and water-vapor samples can be analyzed with a better than 8 per meg precision for Δ17O using integration times of less than 30 min. Calibration with respect to accepted water standards demonstrates that both the precision and the accuracy of Δ17O are competitive with conventional IRMS methods. The new instrument also achieves simultaneous analysis of δ18O, Δ17O and δD with precision of &lt; 0.03‰, &lt; 0.02 and &lt; 0.2‰, respectively, based on repeated calibrated measurements.

USGS48 Puerto Rico precipitation – a new isotopic reference material for δ2H and δ18O measurements of water

A new secondary isotopic reference material has been prepared from Puerto Rico precipitation, which was filtered, homogenised, loaded into glass ampoules, sealed with a torch, autoclaved to eliminate biological activity, and calibrated by dual-inlet isotope-ratio mass spectrometry. This isotopic reference material, designated as USGS48, is intended to be one of two isotopic reference waters for daily normalisation of stable hydrogen (δ2H) and stable oxygen (δ18O) isotopic analysis of water with a mass spectrometer or a laser absorption spectrometer. The δ2H and δ18O values of this reference water are−2.0±0.4 and−2.224±0.012 ‰, respectively, relative to Vienna Standard Mean Ocean Water on scales normalised such that the δ2H and δ18O values of Standard Light Antarctic Precipitation reference water are−428 and−55.5 ‰, respectively. Each uncertainty is an estimated expanded uncertainty (U=2uc) about the reference value that provides an interval that has about a 95 % probability of encompassing the true value. This isotopic reference water is available by the case of 144 glass ampoules containing 5 mL of water in each ampoule.

Lake Louise Water (USGS47): A new isotopic reference water for stable hydrogen and oxygen isotope measurements

Because of the paucity of isotopic reference waters for daily use, a new secondary isotopic reference material has been prepared from Lake Louise water from Alberta, Canada, for international distribution. This water was filtered, homogenized, loaded into glass ampoules, sealed with a torch, autoclaved to eliminate biological activity, and measured by dual-inlet isotope-ratio mass spectrometry. This isotopic reference water is available by the case of 144 glass ampoules containing 5 mL of water in each ampoule. The δ(2)H and δ(18)O values of this reference water are -150.2 ± 0.5‰ and -19.80 ± 0.02‰, respectively, relative to VSMOW, on scales normalized such that the δ(2)H and δ(18)O values of SLAP reference water are, respectively, -428 and -55.5‰. Each uncertainty is an estimated expanded uncertainty (U = 2uc) about the reference value that provides an interval that has about a 95% probability of encompassing the true value. This isotopic reference material, designated as USGS47, is intended as one of two isotopic reference waters for daily normalization of stable hydrogen and stable oxygen isotopic analysis of water with a mass spectrometer or a laser absorption spectrometer. Published in 2013. This article is a U.S. Government work and is in the public domain in the USA.

Measurement of δ18O and δ2H values of fluid inclusion water in speleothems using cavity ring‐down spectroscopy compared with isotope ratio mass spectrometry

The hydrogen and oxygen isotopic analyses (δ(2)H and δ(18)O values) of water trapped within speleothem carbonate (fluid inclusions) have traditionally been conducted utilizing dual-inlet isotope ratio mass spectrometry (IRMS) or continuous-flow (CF)-IRMS methods. The application of cavity ring-down spectroscopy (CRDS) to the δ(2)H and δ(18)O analysis of water in fluid inclusions has been investigated at the University of Miami as an alternative method to CF-IRMS. An extraction line was developed to recover water from the fluid inclusions consisting of a crusher, sample injection port and an expansion volume (either 100 or 50 cm(3)) directly connected to the CRDS instrument. Tests were conducted to determine the reproducibility of standard water injections and crushes. In order to compare results with conventional analytical methods, samples were analyzed both at the University of Miami (CRDS method) and at the Vrije Universiteit Amsterdam (CF-IRMS method). The analytical reproducibility of speleothem samples crushed on the Miami Device demonstrates an average external standard deviation of 0.5 and 2.0 ‰ for δ(18)O and δ(2)H values, respectively. Sample data are shown to fall near the global meteoric water line, supporting the validity of the method. Three different samples were analyzed at Vrije Universiteit Amsterdam and the University of Miami in order to compare the performance of each laboratory. The average offset between the two laboratories is 0.7 ‰ for δ(18)O and 2.5 ‰ for δ(2)H. The advantage of CRDS is that the system is a low-cost alternative to CF-IRMS for fluid inclusion isotope analysis. The CRDS method demonstrates acceptable precision and good agreement with results from the CF-IRMS method. These are promising results for the future application of CRDS to fluid inclusion isotope analysis.