Dual-energy Computed Tomography Reconstruction Research Articles

A dual-energy CT reconstruction method based on anchor network from dual quarter scans.

Compared with conventional single-energy computed tomography (CT), dual-energy CT (DECT) provides better material differentiation but most DECT imaging systems require dual full-angle projection data at different X-ray spectra. Relaxing the requirement of data acquisition is an attractive research to promote the applications of DECT in wide range areas and reduce the radiation dose as low as reasonably achievable. In this work, we design a novel DECT imaging scheme with dual quarter scans and propose an efficient method to reconstruct the desired DECT images from the dual limited-angle projection data. We first study the characteristics of limited-angle artifacts under dual quarter scans scheme, and find that the negative and positive artifacts of DECT images are complementarily distributed in image domain because the corresponding X-rays of high- and low-energy scans are symmetric. Inspired by this finding, a fusion CT image is generated by integrating the limited-angle DECT images of dual quarter scans. This strategy enhances the true image information and suppresses the limited-angle artifacts, thereby restoring the image edges and inner structures. Utilizing the capability of neural network in the modeling of nonlinear problem, a novel Anchor network with single-entry double-out architecture is designed in this work to yield the desired DECT images from the generated fusion CT image. Experimental results on the simulated and real data verify the effectiveness of the proposed method. This work enables DECT on imaging configurations with half-scan and largely reduces scanning angles and radiation doses.

Virtual non-enhanced dual-energy computed tomography reconstruction: a candidate to replace true non-enhanced computed tomography scans in the setting of suspected liver alveolar echinococcosis.

When a suspected hepatic alveolar echinococcosis (AE) lesion is detected on a contrast enhanced computed tomography (CT) scan, an additional triphasic or non-enhanced CT scan is required to determine the presence of calcification and enhancement. As a result, imaging costs and exposure to ionizing radiation will increase. We can create a non-enhanced series from routine contrast-enhanced images using dual-energy CT (DECT) and virtual non-enhanced (VNE) images. This study's objective is to assess virtual non-enhanced DECT reconstruction as a potential diagnostic tool for hepatic AE. Triphasic CT scans and a routine dual energy venous phase were acquired using a third-generation DECT system. A commercially available software package was used to generate VNE images. Individual evaluations were conducted by two radiologists. The study population consisted of 100 patients (30 AE, 70 other solid liver masses). All AE cases were diagnosed [no false positives/negatives, 95% confidence interval (CI) sensitivity: 91.3%-100%; 95% CI specificity: 95.3%-100%]. Interrater agreement was k: 0.79. In total, 33 (33.00%) of the patients had AE, which was detected using both true non-enhanced (TNE) and VNE images. The mean dose-length product of a standard triphasic CT was significantly higher than biphasic dual-energy VNE images. In terms of diagnostic confidence, VNE images are comparable with actual non-enhanced imaging when evaluating hepatic AE. Further, VNE images could replace TNE images with a substantial radiation dose reduction. Advances in knowledge: hepatic cystic echinococcosis and AE are serious and severe diseases with high fatality rates and a poor prognosis if managed incorrectly, especially AE. Moreover, VNE images produce equal diagnostic confidence to TNE images for assessing liver AE, with a significant reduction in radiation dose.

One half-scan dual-energy CT imaging using the Dual-domain Dual-way Estimated Network (DoDa-Net) model.

Compared with single-energy computed tomography (CT), dual-energy CT (DECT) can distinguish materials better. However, most DECT reconstruction theories require two full-scan projection datasets of different energies, and this requirement is hard to meet, especially for cases where a physical blockage disables a full circular rotation. Thus, it is critical to relax the requirements of data acquisition to promote the application of DECT. A flexible one half-scan DECT scheme is proposed, which acquires two projection datasets on two-quarter arcs (one for each energy). The limited-angle problem of the one half-scan DECT scheme can be solved by a reconstruction method. Thus, a dual-domain dual-way estimation network called DoDa-Net is proposed by utilizing the ability of deep learning in non-linear mapping. Specifically, the dual-way mapping Generative Adversarial Network (DM-GAN) was first designed to mine the relationship between two different energy projection data. Two half-scan projection datasets were obtained, the data of which was twice that of the original projection dataset. Furthermore, the data transformation from the projection domain to the image domain was realized by the total variation (TV)-based method. In addition, the image processing network (Im-Net) was employed to optimize the image domain data. The proposed method was applied to a digital phantom and real anthropomorphic head phantom data to verify its effectiveness. The reconstruction results of the real data are encouraging and prove the proposed method's ability to suppress noise while preserving image details. Also, the experiments conducted on simulated data show that the proposed method obtains the closest results to the ground truth among the comparison methods. For low- and high-energy reconstruction, the peak signal-to-noise ratio (PSNR) of the proposed method is as high as 40.3899 and 40.5573 dB, while the PSNR of other methods is lower than 36.5200 dB. Compared with FBP, TV, and other GAN-based methods, the proposed method reduces root mean square error (RMSE) by, respectively, 0.0124, 0.0037, and 0.0016 for low-energy reconstruction, and 0.0102, 0.0028, and 0.0015 for high-energy reconstruction. The developed DoDa-Net model for the proposed one half-scan DECT scheme consists of two stages. In stage one, DM-GAN is used to realize the dual map of projection data. In stage two, the TV-based method is employed to transform the data from the projection domain to the image domain. Furthermore, the reconstructed image is processed by the Im-Net. According to the experimental results of qualitative and quantitative evaluation, the proposed method has advantages in detail preservation, indicating the potential of the proposed method in one half-scan DECT reconstruction.

An iterative reconstruction method based on monochromatic images for dual energy CT.

Dual-energy computed tomography (DECT) scans objects using two different X-ray spectra to acquire more information, which is also called dual spectral CT (DSCT) in some articles. Compared to traditional CT, DECT exhibits superior material distinguishability. Therefore, DECT can be widely used in the medical and industrial domains. However, owing to the nonlinearity and ill condition of DECT, studies are underway on DECT reconstruction to obtain high quality images and achieve fast convergence speed. Therefore, in this study, we propose an iterative reconstruction method based on monochromatic images (IRM-MI) to rapidly obtain high-quality images in DECT reconstruction. An IRM-MI is proposed for DECT. The proposed method converts DECT reconstruction problem from the basis material images decomposition to monochromatic images decomposition to significantly improve the convergence speed of DECT reconstruction by changing the coefficient matrix of the original equations to increase the angle of the high- and low-energy projection curves or reduce the condition number of the coefficient matrix. The monochromatic images were then decomposed into basis material images. Furthermore, we conducted numerical experiments to evaluate the performance of the proposed method. The decomposition results of the simulated data and real data experiments confirmed the effectiveness of the proposed method. Compared to the extended algebraic reconstruction technique (E-ART) method, the proposed method exhibited a significant increase in the convergence speed by increasing the angle of polychromatic projection curves or decreasing the condition number of the coefficient matrix, when choosing the appropriate monochromatic images. Therefore, the proposed method is also advantageous in acquiring high quality and rapidly converged images. We developed an iterative reconstruction method based on monochromatic images for the material decomposition for DECT. The numerical experiments using the proposed method validated its capability of decomposing the basis material images. Furthermore, the proposed method achieved faster convergence speed compared to the E-ART method.

Reconstruction method for DECT with one half-scan plus a second limited-angle scan using prior knowledge of complementary support set (Pri-CSS)

Dual-energy computed tomography (DECT) has capability to improve material differentiation, but most scanning schemes require two sets of full-scan measurements at different x-ray spectra, limiting its application to imaging system with incomplete scan. In this study, using one half-scan and a second limited-angle scan, we propose a DECT reconstruction method by exploiting the consistent information of gradient images at high- and low-energy spectra, which relaxes the requirement of data acquisition of DECT. Based on the theory of sampling condition analysis, the complementary support set of gradient images plays an important role in image reconstruction because it constitutes the sufficient and necessary condition for accurate CT reconstruction. For DECT, the gradient images of high- and low-energy CT images ideally share the same complementary support set for the same object. Inspired by this idea, we extract the prior knowledge of complementary support set (Pri-CSS) from the gradient image of the first half-scan CT image to promote the second limited-angle CT reconstruction. Pri-CSS will be incorporated into total variation regularization model in the form of constrains. Alternative direction method is applied to iteratively solve the modified optimization model, thereby deriving the proposed algorithm to recover low-energy CT image from limited-angle measurements. The qualitative and quantitative experiments on digital and real data are performed to validate the proposed method. The results show that the proposed method outperforms its counterparts and achieve high reconstruction quality for the designed scanning configuration.

Gout: Update on Dual-Energy Computed Tomography with Emphasis on Artifact Identification

Gout is the most common inflammatory arthritis and is increasing in prevalence and incidence in many countries worldwide. Accurate diagnosis is important to direct treatment that may include chronic medication. Burden quantification and treatment monitoring are key in the effective care of patients with gout. This review highlights the positive impact of dual-energy computed tomography (DECT) on the evaluation of gout patients and discusses common imaging artifacts that limit this imaging modality. DECT has become the most accurate imaging method for confirming or excluding gout. Of note, however, it has reduced sensitivity in early disease, including initial attacks. Burden quantification is another important role of DECT, which can now be performed using automated software methods, allowing for a more reliable assessment of treatment effect. However, the analysis of gout DECT images can be impeded by artifacts related to the DECT reconstruction technique. DECT is the most sensitive and specific imaging modality for diagnosis, burden quantification, and treatment monitoring in patients with gout. A working knowledge of common DECT artifacts is essential for mitigating their occurance and misinterpretation.

Image-domain multimaterial decomposition for dual-energy CT based on prior information of material images.

Dual-Energy Computed Tomography (DECT) is of great interest in medical imaging, security inspection, and nondestructive testing. Most DECT reconstruction methods focus on producing two material images with different linear attenuation coefficients. However, the ability to reconstruct three or more basis materials is clinically and industrially important. Under the assumption that there are at most three materials in each pixel, there are a few methods that estimate multiple material images from DECT measurements by enforcing sum-to-one and a box constraint ([0 1]) derived from both the volume and mass conservation assumption. The recently proposed image-domain multimaterial decomposition (MMD) method introduces edge-preserving regularization for each material image. It enforces the assumption that there are at most three materials in each pixel using a time-consuming loop over all possible material triplets. However, this method neglects relations among material images. We propose a new image-domain MMD model for DECT that considers the prior information that different material images have common or complementary edges and encourages sparsity of material composition in each pixel using regularization. The proposed PWLS-TNV-ℓ0 method uses penalized weighted least-square (PWLS) reconstruction with three regularization terms. The first term is total nuclear variation (TNV) that accounts for the image property that basis material images share common or complementary boundaries and each material image is piecewise constant. The second term is an ℓ0 norm that encourages each pixel containing a small subset of material types out of several possible materials. The third term is a characteristic function based on sum-to-one and a box constraint derived from the volume and mass conservation assumption. We apply the Alternating Direction Method of Multipliers (ADMM) to optimize the cost function of the PWLS-TNV-ℓ0 method. We evaluated the proposed method on a simulated digital phantom, Catphan©600 phantom and patient's pelvis data. We implemented two existing image-domain MMD methods for DECT, the Direct Inversion and the PWLS-EP-LOOP method. We initialized the PWLS-TNV-ℓ0 method and the PWLS-EP-LOOP method with the results of the Direct Inversion method and compared performance of the proposed method with that of the PWLS-EP-LOOP method. The proposed method lowers the bias of decomposed material fractions by 84.47% in the digital phantom study, by 99.50% in the Catphan©600 phantom study, and by 99.64% in the pelvis patient study, respectively, compared to the PWLS-EP-LOOP method. The proposed method reduces noise standard deviation (STD) by 52.21% in the Catphan©600 phantom study, and by 16.74% in the patient's pelvis study, compared to the PWLS-EP-LOOP method. The proposed method increases volume fraction accuracy by 6.04%,20.55%, and 13.46% for the digital phantom, the Catphan©600 phantom, and the patient's pelvis study, respectively, compared to the PWLS-EP-LOOP method. Compared with the PWLS-EP-LOOP method, the root mean square percentage error [RMSE(%)] of electron densities in the Catphan©600 phantom is decreased by about 7.39%. We proposed an image-domain MMD method, PWLS-TNV-ℓ0 , for DECT. The PWLS-TNV-ℓ0 method takes low rank property of material image gradients, sparsity of material composition and mass and volume conservation into consideration. The proposed method suppresses noise, reduces cross contamination, and improves accuracy in the decomposed material images, compared to the PWLS-EP-LOOP method.

The acceleration algorithm for projection decomposition of dual-energy computed tomography image reconstruction based on projection matching

Dual-energy computed tomography (CT) reconstruction imaging technology is an important development direction in the field of CT imaging. The mainstream model of dual-energy CT reconstruction algorithm is the basis material decomposition model, and the projection decomposition is the crucial technique. The projection decomposition algorithm based on projection matching was a general method. With establishing the energy spectrum lookup table, we can obtain the stable solution by the least squares matching method. But the computation cost will increase dramatically when size of lookup table enlarges and it will slow down the computer. In this paper, an acceleration algorithm based on projection matching is proposed. The proposed algorithm makes use of linear equations and plane equations to fit the lookup table data, so that the projection value of the decomposition coefficients can be calculated quickly. As the result of simulation experiment, the acceleration algorithm can greatly shorten the running time of the program to get the stable and correct solution.

Iterative reconstruction for dual energy CT with an average image-induced nonlocal means regularization

Reducing radiation dose in dual energy computed tomography (DECT) is highly desirable but it may lead to excessive noise in the filtered backprojection (FBP) reconstructed DECT images, which can inevitably increase the diagnostic uncertainty. To obtain clinically acceptable DECT images from low-mAs acquisitions, in this work we develop a novel scheme based on measurement of DECT data. In this scheme, inspired by the success of edge-preserving non-local means (NLM) filtering in CT imaging and the intrinsic characteristics underlying DECT images, i.e. global correlation and non-local similarity, an averaged image induced NLM-based (aviNLM) regularization is incorporated into the penalized weighted least-squares (PWLS) framework. Specifically, the presented NLM-based regularization is designed by averaging the acquired DECT images, which takes the image similarity within the two energies into consideration. In addition, the weighted least-squares term takes into account DECT data-dependent variance. For simplicity, the presented scheme was termed as ‘PWLS-aviNLM’. The performance of the presented PWLS-aviNLM algorithm was validated and evaluated on digital phantom, physical phantom and patient data. The extensive experiments validated that the presented PWLS-aviNLM algorithm outperforms the FBP, PWLS-TV and PWLS-NLM algorithms quantitatively. More importantly, it delivers the best qualitative results with the finest details and the fewest noise-induced artifacts, due to the aviNLM regularization learned from DECT images. This study demonstrated the feasibility and efficacy of the presented PWLS-aviNLM algorithm to improve the DECT reconstruction and resulting material decomposition.

A full‐spectral Bayesian reconstruction approach based on the material decomposition model applied in dual‐energy computed tomography

Dual-energy computed tomography (DECT) makes it possible to get two fractions of basis materials without segmentation. One is the soft-tissue equivalent water fraction and the other is the hard-matter equivalent bone fraction. Practical DECT measurements are usually obtained with polychromatic x-ray beams. Existing reconstruction approaches based on linear forward models without counting the beam polychromaticity fail to estimate the correct decomposition fractions and result in beam-hardening artifacts (BHA). The existing BHA correction approaches either need to refer to calibration measurements or suffer from the noise amplification caused by the negative-log preprocessing and the ill-conditioned water and bone separation problem. To overcome these problems, statistical DECT reconstruction approaches based on nonlinear forward models counting the beam polychromaticity show great potential for giving accurate fraction images. This work proposes a full-spectral Bayesian reconstruction approach which allows the reconstruction of high quality fraction images from ordinary polychromatic measurements. This approach is based on a Gaussian noise model with unknown variance assigned directly to the projections without taking negative-log. Referring to Bayesian inferences, the decomposition fractions and observation variance are estimated by using the joint maximum a posteriori (MAP) estimation method. Subject to an adaptive prior model assigned to the variance, the joint estimation problem is then simplified into a single estimation problem. It transforms the joint MAP estimation problem into a minimization problem with a nonquadratic cost function. To solve it, the use of a monotone conjugate gradient algorithm with suboptimal descent steps is proposed. The performance of the proposed approach is analyzed with both simulated and experimental data. The results show that the proposed Bayesian approach is robust to noise and materials. It is also necessary to have the accurate spectrum information about the source-detector system. When dealing with experimental data, the spectrum can be predicted by a Monte Carlo simulator. For the materials between water and bone, less than 5% separation errors are observed on the estimated decomposition fractions. The proposed approach is a statistical reconstruction approach based on a nonlinear forward model counting the full beam polychromaticity and applied directly to the projections without taking negative-log. Compared to the approaches based on linear forward models and the BHA correction approaches, it has advantages in noise robustness and reconstruction accuracy.

A Reconstruction Method for Dual High-Energy CT With MeV X-Rays

Dual-energy computed tomography (DECT) allows one to obtain both density and atomic number and thus can provide information about material composition of scanned objects. In this paper, we extend a basis material decomposition method for high energy X-ray DECT used in cargo inspection. It differs from conventional DECT reconstruction methods by pair-production effect coming into play in the reconstruction. The pair-production does not happen for DECT in low energy level (lower than 1 MeV). The decomposition error of the basis material model and its applicability in the high-energy level are analyzed in this paper. A reconstruction method based on this model is proposed to reconstruct both the atomic number <i xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">Z</i> and the electron density ρ <i xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">e</i> images for a high-energy DECT. The method is validated by a numerical simulation and a practical experiment on a cargo inspection system. Results show that the proposed reconstruction method is strongly grounded on physics and feasible for high-energy DECT in material discrimination, especially for cargo inspections. The advantages and limitations of the high-energy DECT, as well as possible improvements for future work are discussed in this paper.

Myocardial Ischemia Diagnosed by Dual-Energy Computed Tomography

For decades, dual-energy imaging has been used for tissue differentiation with several x-ray–based imaging modalities, exploiting the fact that the tissues in the human body show different absorption characteristics when penetrated with different x-ray spectra, spectra that are typically generated by different kV settings of the x-ray tube. Recently, dual-source computed tomography (CT) with 2 x-ray tubes and 2 detector arrays mounted in the same gantry has become available.1 After experience with earlier experimental prototypes, this dual-source CT for the first time enables the clinical acquisition of dual-energy CT studies simultaneously with a single scan. We used a dual-source CT scanner (Definition, Siemens, Forchheim, Germany) in dual-energy mode for performing coronary CT angiography in a 74-year–old woman with suspected coronary artery disease and prior abnormal nuclear rest/stress single-photon emission CT (SPECT). The CT scan was acquired with retrospective ECG-gating and the following scan parameters: 330-ms gantry rotation, pitch 0.2, and 32×2×0.6-mm …