Dry Resin Research Articles

Process for the Recovery of Actinide and Lanthanide Oxides via Thermal Decomposition and Calcination of Loaded Diglycolamide Resin

Diglycolamide (DGA) resin, a product produced by Eichrom Technologies, Inc. employs TODGA (N,N,N′,N′-tetraoctyldiglycolamide) as the active extractant, which will be used by Savannah River National Laboratory to extract trivalent actinides and lanthanides from dissolved irradiated Mark-18A targets. The final form of the extracted material will be an oxide suitable for shipment. A two-step process was developed and validated for the direct recovery of actinides and lanthanides loaded on I-grade DGA resin as nitrates by thermally drying and decomposing resin loaded with Nd(III), a surrogate for trivalent actinides and lanthanides, under inert conditions followed by calcining the resultant residue in air to provide an oxide product. A stepwise heating profile up to 385°C under argon gas flow resulted in 85% to 89% mass loss during the resin drying and decomposition step, and calcination of the resultant Nd-loaded resin residue provided an overall material mass loss of ≥ 98%. Recoveries from resin saturated with Nd(III) from 7 M and 0.35 M nitric acid subjected to this process were 30.7 mg and 27.6 mg Nd/g dry resin, respectively, representing an average of 96.1% of Nd retained in the resin bed.

Weibull Technique for Evaluation of Swelling: Composite Graphite Resin Electrode for Electrochemical Treatment of Gold Mining Wastewaters

This paper evaluated the swelling of graphite resin electrodes developed for utilization in the electrochemical treatment of gold mining wastewater. Graphite-resin electrodes were developed from used dry cells and resin using non-heat treatment processes (segregation). The Microstructure of the electrode was determined using a scanning electron microscope (Carl Zeiss Smart Evo 10) to ascertain the composition of the electrode. The swelling property of the electrodes was measured using the standard method through a combination of gold mining wastewater and chloride salt solutions. Effects of operational factors (particle size, percentage binder and compressive “compacting” pressure) on the swelling of the electrodes were monitored and evaluated statistically (using analysis of variance). Weibull probability distribution (2 and 3 parameters) was applied to the swelling through Microsoft Excel Solver and Moment Likelihood Method to ascertain the usefulness of the electrode in environmental pollution control through computation of reliability. The study revealed that the swelling was in the range of 1.48 % to 2.24 %, particle size (F5,20 =196.48, p = 2.76 x 10-16), percentage binder (F4,12 =181.58, p = 1.27 x 10-10), and compressive pressure (F3,12 = 106.69, p = 6.43 x 10-9) were significant factors that influence swelling of graphite-resin electrode at 95 % confidence level. the values of α and β for 2-parameters Weibull distribution are 63.162 and 15.098, and 1.265 and 10.089 for MSE and MLM methods, respectively. The Table shows that the values of α, β and θ for 3-parameters Weibull distribution are 3.679, 8.097 and 0.168, and 4.350, 7.165 and 0.198 for MSE and MLM methods, respectively. It was concluded that particle size and compacting pressure are significant factors that had an effect on the swelling of graphite resin electrodes for treatment water and wastewater.

Fabrication and mechanical characterization of composite fiberboard utilizing dry lemon peel powder and epoxy resin

This research work is related to the manufacturing of a composite fiberboard using dry lemon peel powder and epoxy resin, which can be used as an alternate to the plywood or wood. The objective of this study is to assess the mechanical and microstructural properties of this novel composite fiberboard. To assess its strength and ability to absorb energy, different tests were performed on different specimens. To comprehend the morphology and filler particle distribution within the resin, the microstructure of the fabricated composite was also checked using a scanning electron microscope (SEM). As per the experimental findings, the composite’s mechanical properties, such as hardness 22.45 (Vickers), tensile strength 14.7 MPa, flexural strength 27.9 MPa and impact strength 21.76 J/m2, appeared promising with respect to the plywood. Additionally, perfect bonding was shown by the SEM study between the waste Dry Lemon Peel particles (DLPP) and the epoxy, contributing to improved mechanical properties

Emerging tendencies for the nano-delivery of gambogic acid: a promising approach in oncotherapy.

Despite the advancements in cancer therapies during the past few years, chemo/photo resistance, severe toxic effects, recurrence of metastatic tumors, and non-selective targeting remain incomprehensible. Thus, much effort has been spent exploring natural anticancer compounds endowed with biosafety and high effectiveness in cancer prevention and therapy. Gambogic acid (GA) is a promising natural compound in cancer therapy. It is the major xanthone component of the dry resin extracted from the Garcinia hanburyi Hook. f. tree. GA has significant antiproliferative effects on different types of cancer, and it exerts its anticancer activities through various pathways. Nonetheless, the clinical translation of GA has been hampered, partly due to its water insolubility, low bioavailability, poor pharmacokinetics, rapid plasma clearance, early degradation in blood circulation, and detrimental vascular irritation. Lately, procedures have been invented demonstrating the ability of nanoparticles to overcome the challenges associated with the clinical use of natural compounds both in vitro and in vivo. This review sheds light on the recent emerging trends for the nanodelivery of GA to cancer cells. To the best of our knowledge, no similar recent review described the different nanoformulations designed to improve the anticancer therapeutic activity and targeting ability of GA.

Effect of gaps on preform and laminate made by automated dry fiber placement and resin infusion

Automated Dry Fiber Placement (ADFP) provides ease in fiber steering compared to the automated placement of prepregs and a higher material deposition rate than manual hand layup. Vacuum Assisted Resin Infusion (VARI) can be used to infuse the resin into the bed of dry fibers to make the composite. The resin flow rate depends on the permeability of the dry fiber preform, which is dependent on the preform fiber volume fraction. Automated Fiber Placement (AFP) allows the capacity to control the fiber volume fraction in terms of gaps between the tows. So, reducing the fiber volume fraction of preforms by introducing gaps into the preform pattern can increase the permeability. On the other hand, introducing gaps in layup results in a drop in the mechanical properties of the laminate (such as compressive modulus and strength). An optimum gap size may provide a significant gain in permeability with minimum loss in compressive properties. This paper investigates the effect of the gap size in the preform pattern on the preform out-of-plane permeability and compressive properties of the laminate. The out-of-plane permeability of three specimens from preforms, with varying gap sizes (0mm, 0.4mm, and 0.8mm) in all layers were measured. Also, the compressive properties of five coupons made from laminates, with and without gap sizes (0mm, 0.4mm, and 0.8mm) were determined. It was shown that introducing gaps with 0.4 mm size between fiber tapes in the layup can increase the out-of-plane permeability 17 times and reduce the compressive strength and modulus by 6 % and 7.2 %, respectively.

A multiscale deep learning model for elastic properties of woven composites

Time-consuming and costly computational analysis expresses the need for new methods for generalizing multiscale analysis of composite materials. Combining neural networks and multiscale modeling is favorable for bypassing expensive lower-scale material modeling, and accelerating coupled multi-scale analyses (FE2). In this work, neural networks are used to replace the time-consuming micromechanical finite element analysis of unidirectional composites, representing the local material properties of yarns in woven fabric composites in a multiscale framework. Leveraging the fast multiscale data generation procedure, we presented a second neural networks model to estimate the elastic engineering coefficients of a particular weave architecture based on a broad range of dry resin and fiber properties and yarn fiber volume fraction. As an outcome, this paper provides the user with a generalized, neural network-based approach to tackle the balance of computational efficiency and accuracy in the multiscale analysis of elastic woven composites.

Exploring Fully Biobased Adhesives: Sustainable Kraft Lignin and 5-HMF Adhesive for Particleboards.

Most adhesives used in the wood-based panel (WBP) industry are petroleum-based and are associated with environmental impact and price fluctuations. Furthermore, most have potential adverse health impacts, such as formaldehyde emissions. This has led to interest from the WBP industry in developing adhesives with bio-based and/or non-hazardous components. This research focuses on the replacement of phenol-formaldehyde resins by Kraft lignin for phenol substitution and 5-hydroxymethylfurfural (5-HMF) for formaldehyde substitution. Resin development and optimization was carried out regarding varying parameters such as molar ratio, temperature or pH. The adhesive properties were analyzed using a rheometer, gel timer and a differential scanning calorimeter (DSC). The bonding performances were evaluated using an Automated Bonding Evaluation System (ABES). Particleboards were produced using a hot press, and their internal bond strength (IB) was evaluated according to SN EN 319. Hardening of the adhesive could be achieved at low temperatures by increasing or decreasing the pH. The most promising results were obtained at pH 13.7. The adhesive performances were improved by adding filler and extender (up to 28.6% based on dry resin) and several boards were produced reaching P1 requirements. A particleboard achieved a mean IB of 0.29 N/mm2, almost reaching almost P2 requirements. However, adhesive reactivity and strength must be improved for industrial use.

Phenolic hydroxyl functionalized hyper-crosslinked polymers and their efficient adsorption

Phenolic hydroxyl modified hyper-crosslinked polymers were synthesized according to two consecutive Friedel-Crafts reactions. The first Friedel-Crafts reaction grafted plentiful phenolic hydroxyl on the polymers, and the second Friedel-Crafts reaction inserted abundant methylene in the polymer chains. The resulting polymers had relatively high Brunauer-Emmet-Teller (BET) surface area (SBET) and pore volume (Vtotal). The adsorption experiments indicated that the intermediate polymer, namely, PS-CA (Polystyrene-Catechol), showed excellent adsorption for berberine hydrochloride (BBH) with the maximum capacity (qmax) of 505.42 mg/g at 298 K, and the electrostatic interaction, π-π stacking and hydrogen bonding were the main driving forces. Anhydrous alcohol could desorb 75.36% of the adsorbed BBH from the polymer. On the other hand, the final polymers owned much higher adsorption of aniline and β-naphthylamine due to the micropore-filling. The dynamic adsorption used Chinese herbs Coptidis rhizoma solution present that the dynamic capacity was 248.70 mg/g dry resin.

Diagnosing of the Glass Fiber Reinforced Polymer Material High Performance Drilling Process State

The article presents the results of works on the analysis of using cutting forces and torque measurements to determine the state of dry fiberglass matrix polyester resin composite high performance drilling process. The research and analyzes were carried out for the different states of tool state and the process state itself. GFRP - Glass Fiber Reinforced Polymer was used to perform the experiment. As a result of the conducted analyzes, it was determined that booth the forces and torque generated in drilling process can constitute a good diagnostic signal, on the basis of which it is possible to conclude about the state of the process and tool.

Guayule growth and yield responses to deficit irrigation strategies in the U.S. desert

Deficit irrigation can maximize the water productivity (WP) of guayule and increase the percent rubber (%R) in shrubs compared to irrigation meeting full crop evapotranspiration (ETc). In this study, we hypothesize that certain deficit irrigation strategies that impose soil water deficits during specific periods of growth or throughout the growing season might produce higher %R and equivalent rubber yield (RY), thereby, increasing WP compared to full irrigation. Herein, growth and yield responses of direct-seeded guayule to different water deficit schemes were evaluated in an experiment on a silty clay loam soil, in a field in central Arizona using furrow irrigation. Two guayule cultivars (AZ2 and AZ6) were grown for 22.5 months (Apr. 2020-Mar. 2022) in a split-plot design, with six irrigation treatments in whole plots and cultivars in split-plots. After homogeneous irrigation for two months, irrigation treatments were begun. A control treatment was irrigated to meet full ETc. The other five treatments were irrigated with less water using various deficit irrigation strategies imposed during the two-year growing period. Measurements included plant height (h), cover fraction (fc), soil water contents, harvest of dry biomass (DB), RY, resin yield (ReY), %R, and percent resin (%Re). Total water applied (TWA) by irrigation and precipitation to treatments varied from 2780 to 1084 mm and DB varied from 20.5 to 9.1 Mg ha−1. The h and fc were significantly greater at higher irrigation levels, while they were also significantly greater in AZ6 than AZ2. The DB, RY, and ReY generally increased linearly with TWA. However, it was found that a treatment applying every other irrigation of the control resulted in statistically equivalent yields to the control, with 36% less irrigation. The %R generally decreased with TWA, while %Re did not change. However, DB, %R, and %Re were significantly greater for AZ2 than AZ6, as were RY, ReY, and WP. Among the deficit treatments evaluated, every other irrigation offers the best strategy to significantly increase guayule WP without causing a yield penalty.

Radiation stability of two extraction chromatography resin materials containing substituted diglycolamide ligands in an ionic liquid

The radiation stability of two extraction chromatography resins containing diglycolamide ligands viz. TPDGA (N,N,N’,N’-tetra-n-pentyl diglycolamide) and TODGA (N,N,N’,N’-tetra-n-octyl diglycolamide) in a room temperature ionic liquid (C4mim.NTf2) was studied by exposing to gamma rays from a 60Co source. The resins were irradiated to varying gamma ray dose up to 1000 kGy where both the dry resins and wet resins (containing a fixed amount nitric acid in contact) were used. The performance assessment of the resins was done by physicochemical characterization as well as uptake studies; both by batch as well as column methods. The physicochemical characterization of the resins was done using FTIR analysis while the surface morphology of the resins was carried out by scanning electron microscopy. The uptake of the metal ions, typically that of Am(III) and Eu(III), representing the trivalent actinides and lanthanides was studied by batch method. The dry resins and those in contact with nitric acid yielded nearly identical results suggesting minimal effect of the radiolytic products of nitric acid on the resin performance. There was negligible change in the Kd values up to an absorbed dose of 300 kGy beyond which there was sharp decrease. However, the Kd values were still quite large even after an absorbed dose of 1000 kGy. The column performance of the irradiated resins was also assessed by the uptake and elution of Eu(III) ion and though loading was affected, the elution behavior was found to have insignificant effect.

Vancomycin Adsorption during in vitro Model of Hemoperfusion with Mini-Module of HA380 Cartridge

Introduction: Sepsis is a frequent complication in critically ill patients. Patients may require control of the source of infection, removal of pathogens and damaged cells, and organ support. Often, these targets can be achieved through the utilization of extracorporeal therapies including hemoperfusion for the adsorption of cytokines and other circulating mediators. On extracorporeal organ support, patients are generally treated with antibiotic therapy, and vancomycin is one of the most commonly used antibiotics. Because of the aspecific nature of adsorption, antibiotics can be removed from the circulation, leading to altered plasma levels and requiring prescription adjustment. The aim was to define the amount of vancomycin adsorbed by a sorbent cartridge (HA380, Jafron, China) during hemoperfusion and to establish possible strategies to maintain an effective plasma level in critically ill patients undergoing extracorporeal therapies. Methods: In vitro experiments with incremental concentrations of vancomycin in the test solution (500 and 1,000 mL) were carried out in a recirculation circuit until sorbent saturation was observed. A maximum of 10 g of vancomycin were injected and mini-modules containing 25 g of dry resin were utilized. Results: In different experiments with various concentration of vancomycin, a maximum amount of 244 mg/g of sorbent was adsorbed reaching saturation between 60 and 80 min from the beginning of the experiments. The kinetics of adsorption appears to be governed by a Langmuir-like isotherm with maximal removal speed in the early minutes and a plateau after 60 min. Discussion/Conclusion: HA380 adsorbs significant amounts of vancomycin. Adjusting the achieved results with the experimental mini-module to a full-scale cartridge, a total of 25 g of antibiotic can be removed. This might have affected outcome results in clinical trials. This suggests prescribing administration to critically ill patients requiring hemoperfusion, immediately after or in the inter-session time window. In case of administration during hemoperfusion, adequate adjustment and plasma level monitoring is strongly recommended.

Direct Air Capture Using Electrochemically Regenerated Anion Exchange Resins.

Direct air capture (DAC) aims to remove CO2 directly from the atmosphere. In this study, we have demonstrated proof-of-concept of a DAC process combining CO2 adsorption in a packed bed of amine-functionalized anion exchange resins (AERs) with a pH swing regeneration using an electrochemical cell (EC). The resin bed was regenerated using the alkaline solution produced in the cathodic compartment of the EC, while high purity CO2 (>95%) was desorbed in the acidifying compartment. After regenerating the AERs, some alkaline solution remained on the surface of the resins and provided additional CO2 capture capacity during adsorption. The highest CO2 capture capacity measured was 1.76 mmol·g–1 dry resins. Moreover, as the whole process was operated at room temperature, the resins did not show any apparent degradation after 150 cycles of adsorption–desorption. Furthermore, when the relative humidity of the air source increased from 33 to 84%, the water loss of the process decreased by 63%, while CO2 capture capacity fell 22%. Finally, although the pressure drop of the adsorption column (5 ± 1 kPa) and the energy consumption of the EC (537 ± 33 kJ·mol–1 at 20 mA·cm–2) are high, we have discussed the potential improvements toward a successful upscaling.

Evaluation and Characterization of Stabilized Drug, Formulated as Oro Dispersible Tablet Using Advanced Method

In a challenge to prepare a stable Oro-dispersible tablet (ODT) of Desloratadine, using dry resin was incorporated into a fast-disintegrating matrix to prepare an optimized ODT that achieved the desired criteria of stabilization and patient acceptance. In this study, the critical process parameters (CPPs) and critical material attributes (CMAs) were determined via risk assessment methods within the framework of Quality by Design (QbD). The results showed that resin (Amberlite IRP64®) can be used as a dry stabilizer and the selected variables in the optimization phase have a strong influence on the blend flowability, disintegration time, and wetting time of the ODTs. Furthermore, by comparing the optimized formula with the marketed one, the optimized formula showed a significantly lower disintegration, lower wetting time, and an almost similar dissolution profile.

Estimation of direct-seeded guayule cover, crop coefficient, and yield using UAS-based multispectral and RGB data

Guayule (Parthenium argentatum, A. Gray), a perennial desert shrub, produces high-quality natural rubber and is targeted as a domestic natural rubber source in the U.S. While commercialization efforts for guayule are on-going, crop management requires plant growth monitoring, irrigation requirement assessment, and final yield estimation. Such assistance for guayule management could be provided with remote sensing (RS) data. In this study, field and RS data, collected via drones, from a 2-year guayule irrigation experiment conducted at Maricopa, Arizona were evaluated. In-season field measurements included fractional canopy cover (fc), basal (Kcb) and single (Kc) crop coefficients, and final yields of dry biomass (DB), rubber (RY), and resin (ReY). The objectives of this paper were to compare vegetations indices from MS data (NDVI) and RGB data (triangular greenness index, TGI); and derive linear prediction models for estimating fc, Kcb, Kc, and yield as functions of the MS and RGB indices. The NDVI and TGI showed similar seasonal trends and were correlated at a coefficient of determination (r2) of 0.52 and a root mean square error (RMSE) of 0.11. The prediction of measured fc as a linear function of NDVI (r2 = 0.90) was better than by TGI (r2 = 0.50). In contrast to TGI, the measured fc was highly correlated with estimated fc based on RGB image evaluation (r2 = 0.96). Linear models of Kcb and Kc, developed over the two years of guayule growth, had similar r2 values vs NDVI (r2 = 0.46 and 0.41, respectively) and vs TGI (r2 = 0.48 and 0.40, respectively). Final DB, RY, and ReY were predicted by both NDVI (r2 = 0.75, 0.53, and 0.70, respectively) and TGI (r2 = 0.72, 0.48, and 0.65, respectively). The RS-based models enable estimation of irrigation requirements and yields in guayule production fields in the U.S.

Oxidation stability and cold flow properties of biodiesel synthesized from castor oil: Influence of alkaline catalysts type and purification techniques

This study investigates the effects of catalyst type and washing procedures on the oxidation stability and cold flow parameters of biodiesel produced from castor oil. Castor oil was synthesized using two different catalysts; calcium oxide on alumina support (CaO-Al2O3) and potassium hydroxide (KOH) at a temperature of 60˚C, methanol to oil molar ratio of 6:1 and catalyst loading of 1 wt% of oil for 60 min. The resulting biodiesel was purified using water washing and dry washing methods ion exchange resin. The oxidation stability and cold flow behaviour of the biodiesel produced (cloud point, pour point, cold filter plugging point, and low-temperature flow test) were determined. The findings showed that the oxidation stability and cold flow properties of biodiesel is independent of washing methods but varies with catalyst type. The heterogeneously catalyzed transesterification by CaO-Al2O3 exhibited higher oxidation stability with an induction period of 4.4 h as against 3.5 h for the potassium hydroxide (KOH) catalyzed biodiesel. However, the values obtained in this study were above the ASTM standard of 3 h minimum. With regards to cold flow properties, the KOH-catalyzed process exhibited better cold flow properties than CaO-Al2O3 catalyzed biodiesel. It can be deduced from this study that the biodiesel samples will exhibit very good ignition performances when used in ignition compression engines in the low temperate region due to their satisfactory cold flow behaviour.

Effects of Activated Carbon on Medium Density Fiber Board Properties

The negative effects of formaldehyde emission in MDF production on human health are known, and therefore many scientists are working to reduce formaldehyde emissions. In this study, the effects of MDF plates on formaldehyde emission were investigated by adding different amounts of activated carbon into urea formaldehyde resin during the synthesis phase.
 
 First, the gelation time behavior of the resin was studied by observing the pH, gelation time, solid content, flow time and viscosity of the modified resin in comparison to the standard reference resin which has no activated carbon inside. The dosing of the activated charcoal in the dry resin was kept at 1wt%, 3wt% and 5wt%. After that modified resin was used in the production of 40x40 cm2 MDF samples by using laboratory scale press line with full automation system. İnternal bonding strength, surface soundness, screw holding resistance, water absorption and thickness swelling were also measured in addition to the main interested parameter formaldehyde emission level which is determined via spectrometric technique following an extraction procedure.
 
 Threshold values for activated carbon were determined to be 1wt%. Formaldehyde emission level was observed where addition of 1wt% activated carbon into the urea formaldehyde adhesive decreased the formaldehyde emission 52% comparison to reference whereas addition of activated carbon at above its threshold level provided 47% decreasing.

Application of additives to manufacture quality towel grade tissue paper with accelerated productivity

Nowadays in paper business sector there is only tissue paper business where growth rate is in double digits since five years consecutivelywhich motivates and encourage entrepreneurs to take up the business with more vigor. Tissue paper is generally categorized in four grades -Napkin grade paper, Toilet grade paper, Facial grade paper and Towel grade paper. Due to higher consumption of towel grade tissue paper at several outlets like offices, educational institutions, aesthetic purposes, common toiletries andhospitalities.This towel grade is being used for wiping wet hands, to meet out these requirements we need to develop high strength in towel grade tissue paper.This study is being conducted to high strength in towel grade tissue paper with application of DSR and WSR. Chemical additives play essential role in production performance of towel grades tissue paper. A significant amount of their tensile strength are retained by wet and dry strength resins .Mixed bleached pulp was collected from pulp mill of a well-known industry. It was refined to different degrees of freeness (°SR) i.e. 25, 30 and 35. Handsheets of pulp refined to different extent, were prepared and physical properties investigated. Based on the specific energy consumption of refiner and the pulp strength properties obtained, pulp freeness with 35°SR were selected for further study. DSR was added in three different doses i.e.2.0, 3.0&4.0 kg/ton and WSR in dosages of 15, 25 & 35 kg/t of pulp. Breaking length and wet strength were enhanced by 32 % and 42 % respectively. On account of this, significant reduction in paper breaks observed on paper machine, which further improved machine runability, reducing downtime. Productivity of machine was enhanced along with supreme quality of towel (interfold) grade tissue paper.

Standardization of a Formulation of Timogar and Ferula Assa-Foetida Dry Resin Extract and its Biological Activity

Standardization of a Formulation of Timogar and Ferula Assa-Foetida Dry Resin Extract and its Biological Activity

Growth, water use, and crop coefficients of direct-seeded guayule with furrow and subsurface drip irrigation in Arizona

Crop establishment costs of guayule (Parthenium argentatum A. Gray), a perennial desert shrub that produces natural rubber, can be significantly reduced using direct seeding rather than the traditional practice of transplanting greenhouse-grown seedlings. However, information regarding the irrigation application, crop evapotranspiration (ETc), and crop coefficients (Kc) for managing direct-seeded guayule crops has not been provided. In this study, guayule was direct-seeded in Apr. 2018 in fields at two location in Arizona; Maricopa, on a sandy loam soil and Eloy, on a clay soil, and harvested 23–24 months later in 2020. At each location, five irrigation rates were applied with subsurface drip irrigation (SDI) ranging from 50 to 150 % replacement of ETc (denoted as D50 to D150 treatments), respectively. A 6th treatment using furrow irrigation at 100 % ETc replacement (F100) was included. Treatments were replicated three times. The ETc was estimated for the first 74–84 days of crop establishment and thereafter, actual ETc (ETc act) was determined weekly-biweekly for the D100 and F100 treatments using a soil water balance. The objectives were to evaluate the responses in dry biomass (DB), rubber yield (RY), and resin (ReY) yield to water application rate, develop irrigation management criteria for the two soil types, and determine the ETc and crop coefficients for the 100 % treatments.The total irrigation applied to treatments ranged from 1830−1910 mm to 5090–5470 and averaged 3590 and 3320 mm for the 100 % SDI (D100) and furrow (F100) treatments at Maricopa and Eloy, respectively. The summed estimated ETc plus ETc act for the D100 and F100 treatments were 3663 and 3506 mm at Maricopa, respectively and 3428 and 3320 at Eloy, respectively. Average measured mid-season Kc in the 1st year varied from 1.20 to 1.26. Average measured mid-season Kc in the 2nd year were higher for D100 (≈1.30) than for F100 (≈1.23). Adjusted to the standard climate proposed in FAO56, mid-season Kc are 1.24 for D100 and 1.17 for F100 in the 2nd year. Average DB at Eloy (28.6 Mg ha−1) was not significantly higher than at Maricopa (24.0 Mg ha−1). However, RY and ReY were both significantly higher at Maricopa. At each location, rubber content was significantly higher for the F100 and the two lowest SDI rates than for other treatments. The highest mean RY and ReY were achieved with D100 at Maricopa and D75 at Eloy. These two also had significantly greater water productivity (WP; DB, RY, and ReY per unit of total water applied) than those at higher SDI rates and the F100 treatments. RY and ReY and their WP were generally higher for D100 than F100 in the sandy loam but not in the clay soil. For direct-seeded guayule in clay soils, furrow irrigation should be considered due to the lower rubber content and higher costs associated with SDI.