Drug Concentration-time Curve Research Articles

Elution and Biomechanical Properties of Meropenem-Loaded Bone Cement.

ObjectiveTo investigate the biomechanical and elution properties of meropenem‐loaded bone cement.MethodsBone cement (Palacos LV) with 5% (2 g/4 0g), 10% (4 g/40 g), and 15% (6 g/40 g) meropenem; 5% (2 g/40 g) and 10% (4 g/40 g) vancomycin; and blank bone cement were prepared in a total of six groups named A2, A4, A6, B2, B4, and A0 (antibiotic‐free). 36 cylinder specimens (6‐mm diameter and 12‐mm height) of all six groups were molded for a compression test. After the compression test, because of mechanical properties below the ISO standard requirements, groups B2, B4 were not subjected to a bending test. So a total of 24 rectangular strip specimens (10‐mm width, 75‐mm length, and 3.3‐mm thickness) for groups A2, A4, A6 and A0 were molded for the bending test. Between‐group differences of compressive strength, bending strength and bending modulus were analyzed. The meropenem standard was prepared as a series of standard solutions to calculate the standard curve. At a constant temperature of 37 °C, separately, meropenem‐loaded bone cement cylinder specimens (12 mm in diameter and 17 mm in length) of A2, A4 and A6 were serially immersed in saline solution without stirring. The eluent drug concentration at 24, 48, 72 h and 6, 12, 24 days was measured and the drug concentration‐time curve of meropenem was constructed.ResultsWith the exception of groups B2 and B4, all cements compressive strength values were well above the minimum requirement of the ISO 5833 standard (70 MPa). The compressive strength and bending strength values of group A4 were higher than those of group A0 (P < 0.05), but no difference was found between the A0, A2 and A6 groups (P > 0.05). There were no intergroup differences of bending modulus between the A0, A2, A4 and A6 groups (P > 0.05). A standard curve of meropenem was obtained and a regression equation was constructed: Y = 15.0265 X + 13.5218, r = 1.00. At 37 °C, the release of meropenem was rapid during the first 48 h for all A2, A4, A6 samples, and subsequent release continued to decrease.ConclusionWhen adding up to 15% (6 g/40 g) meropenem to the bone cement, the biomechanical properties were not reduced, and bone cement with 10% (4 g/40 g) meropenem had the best performance. At a constant temperature of 37°C, meropenem can be released from bone cement for up to 24 days.

Vitamin D levels do not cause vitamin-drug interactions with dexamethasone or dasatinib in mice.

Vitamin D3 (VD3) induces intestinal CYP3A that metabolizes orally administered anti-leukemic chemotherapeutic substrates dexamethasone (DEX) and dasatinib potentially causing a vitamin-drug interaction. To determine the impact of VD3 status on systemic exposure and efficacy of these chemotherapeutic agents, we used VD3 sufficient and deficient mice and performed pharmacokinetic and anti-leukemic efficacy studies. Female C57BL/6J and hCYP3A4 transgenic VD3 deficient mice had significantly lower duodenal (but not hepatic) mouse Cyp3a11 and hCYP3A4 expression compared to VD3 sufficient mice, while duodenal expression of Mdr1a, Bcrp and Mrp4 were significantly higher in deficient mice. When the effect of VD3 status on DEX systemic exposure was compared following a discontinuous oral DEX regimen, similar to that used to treat pediatric acute lymphoblastic leukemia patients, male VD3 deficient mice had significantly higher mean plasma DEX levels (31.7 nM) compared to sufficient mice (12.43 nM) at days 3.5 but not at any later timepoints. Following a single oral gavage of DEX, there was a statistically, but not practically, significant decrease in DEX systemic exposure in VD3 deficient vs. sufficient mice. While VD3 status had no effect on oral dasatinib’s area under the plasma drug concentration-time curve, VD3 deficient male mice had significantly higher dasatinib plasma levels at t = 0.25 hr. Dexamethasone was unable to reverse the poorer survival of VD3 sufficient vs. deficient mice to BCR-ABL leukemia. In conclusion, although VD3 levels significantly altered intestinal mouse Cyp3a in female mice, DEX plasma exposure was only transiently different for orally administered DEX and dasatinib in male mice. Likewise, the small effect size of VD3 deficiency on single oral dose DEX clearance suggests that the clinical significance of VD3 levels on DEX systemic exposure are likely to be limited.

Predicting the Outcome of Voriconazole Individualized Medication Using Integrated Pharmacokinetic/Pharmacodynamic Model.

Therapeutic drug monitoring is considered to be an effective tool for the individualized use of voriconazole. However, drug concentration measurement alone doesn’t take into account the susceptibility of the infecting microorganisms to the drug. Linking pharmacodynamic data with the pharmacokinetic profile of individuals is expected to be an effective method to predict the probability of a certain therapeutic outcome. The objective of this study was to individualize voriconazole regimens by integrating individual pharmacokinetic parameters and pathogen susceptibility data through Monte Carlo simulations The individual pharmacokinetic parameters of 35 hospitalized patients who received voriconazole were calculated based on a validated population pharmacokinetic model. The area under the concentration-time curve for free drug/minimal inhibitory concentration (fAUCss/MIC) > 25 was selected as the pharmacokinetic/pharmacodynamic (PK/PD) parameter predicting the efficacy of voriconazole. The cumulative fraction of response (CFR) of the target value was assessed. To verify this conclusion, a logistic regression analysis was used to explore the relationship between actual clinical efficiency and the CFR value. For the 35 patients, the area under the free drug concentration-time curve (fAUCss) was calculated to be 34.90 ± 21.67 mgh/L. According to the dualistic logistic regression analysis, the minimal inhibitory concentration (MIC) value of different kinds of fungi had a great influence on the effectiveness of clinical treatment. It also showed that the actual clinical efficacy and the CFR value of fAUCss/MIC had a high degree of consistency. The results suggest that it is feasible to individualize voriconazole dosing and predict clinical outcomes through the integration of data on pharmacokinetics and antifungal susceptibility.

Pharmacokinetic Properties of S-oxiracetam After Single and Multiple Intravenous Infusions in Healthy Volunteers.

As a chiral drug, oxiracetam (ORT) can exist in two different isomeric forms: S-oxiracetam (S-ORT) and R-oxiracetam (R-ORT). S-ORT has emerged as a promising nootropic drug with the potential to treat brain injury and the resulting loss of neural function, memory and mental impairment as assessed by studies in various animal models. However, limited data are available on the pharmacokinetics of S-ORT in humans, so the present study was designed to evaluate the safety and pharmacokinetic profile of S-ORT in healthy volunteers. In part 1, subjects were intravenously administered single ascending dose (2.0, 4.0 and 8.0 g) S-ORT. In part 2, subjects were treated at a single intravenous infusion dose of 3.0 g S-ORT or 6.0 g racemic ORT using a two-sequence, two-period crossover design. In part 3, subjects were intravenously injected with 4.0 g S-ORT once a day for 7 days. Blood and urine samples were collected to evaluate the pharmacokinetic parameters and urine excretion rate. The safety profile of the drug was also evaluated throughout the study. Fifty-two subjects (30 in part 1, 12 in part 2, 10 in part 3) completed the study; only one subject displayed a mild adverse event, which possibly was treatment related, and no serious adverse event occurred. In part 1 for a single dose of 2.0, 4.0 and 8.0 g, the maximum concentration (Cmax) values were 111.28±18.99, 230.76±29.16 and 352.67±42.94 μg/ml, respectively; the values of area under the plasma concentration-time curve (AUC) from time zero to the time of last quantifiable concentration (AUC0-t) were 267.09±59.66, 524.50 ±72.87 and 822.68±95.21 μg·h/ml, respectively; the AUC from 0 h to infinity (AUC0-∞) values were 274.72±61.65, 536.06±78.13 and 832.07±96.91 μg·h/ml, respectively. The urine excretion rate of the unchanged drug was approximately 60%. After consecutive administration of S-ORT for 7 days, the accumulation index was 1.05±0.08. The plasma drug concentration-time curves for both S-ORT and R-oxiracetam (R-ORT) were almost identical. S-ORT was well tolerated, and no serious adverse events occurred in 2.0, 4.0 and 8.0 g in single- and 4.0 g in multiple-dose studies. S-ORT showed dose linearity with increasing doses and no drug accumulation after 7 days of continuous administration was observed.

Pharmacokinetic herb-drug interactions between Aidi injection and doxorubicin in rats with diethylnitrosamine-induced hepatocellular carcinoma

BackgroundAidi Injection (ADI), a Chinese herbal preparation with anti-cancer activity, is used for the treatment of hepatocellular carcinoma (HCC). Several clinical studies have shown that co-administration of ADI with doxorubicin (DOX) is associated with reduced toxicity of chemotherapy, enhanced clinical efficacy and improved quality of life for patients. However, limited information is available about the herb-drug interactions between ADI and DOX. The study aimed to investigate the pharmacokinetic mechanism of herb-drug interactions between ADI and DOX in a rat model of HCC.MethodsExperimental HCC was induced in rats by oral administration of diethylnitrosamine. The HCC rats were pretreated with ADI (10 mL/kg, intraperitoneal injection) for 14 consecutive days prior to administration of DOX (7 mg/kg, intravenous injection) to investigate pharmacokinetic interactions. Plasma concentrations of DOX and its major metabolite, doxorubicinol (DOXol), were determined using ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS).ResultsPreadministration of ADI significantly altered the pharmacokinetics of DOX in HCC rats, leading to increased plasma concentrations of both DOX and DOXol. The area under the plasma drug concentration-time curve (AUCs) of DOX and DOXol in rats pretreated with ADI were 3.79-fold and 2.92-fold higher, respectively, than those in control rats that did not receive ADI.ConclusionsIncreased levels of DOX and DOXol were found in the plasma of HCC rats pretreated with ADI.

Evaluation of drug-drug interactions of pemigatinib in healthy participants.

Pemigatinib (INCB054828), a potent and selective oral fibroblast growth factor receptor 1-3 inhibitor, is a Biopharmaceutical Classification System class II compound with good permeability and pH-dependent solubility that is predominantly metabolized by cytochrome P450 (CYP) 3A. Two drug-drug interaction studies, one with acid-reducing agents, esomeprazole (proton pump inhibitor [PPI]) and ranitidine (histamine-2 [H2] antagonist), and the other with potent CYP3A-modulating agents, itraconazole (CYP3A inhibitor) and rifampin (CYP3A inducer), were performed. Both were open-label, fixed-sequence studies conducted in up to 36 healthy participants each, enrolled into two cohorts (n = 18 each). Pemigatinib plasma concentration was measured, and pharmacokinetic parameters were derived by non-compartmental analysis. There was an 88% and 17% increase in pemigatinib area under the plasma drug concentration-time curve (AUC) and maximum plasma drug concentration (Cmax), respectively, with itraconazole, and an 85% and 62% decrease in pemigatinib AUC and Cmax with rifampin coadministration. There was a 35% and 8% decrease in pemigatinib AUC and Cmax, respectively, with esomeprazole, and a 2% decrease in Cmax and 3% increase in AUC with ranitidine coadministration. In both studies, all adverse events reported were grade ≤ 2. Coadministration with itraconazole or rifampin resulted in a clinically significant change in pemigatinib exposure. Therefore, coadministration of strong CYP3A inducers with pemigatinib should be avoided, and the dose of pemigatinib should be reduced if coadministration with strong CYP3A inhibitors cannot be avoided. The effect of PPIs/H2 antagonists on pemigatinib exposure was modest, and pemigatinib can be administered without regard to coadministration of PPIs/H2 antagonists.

In Vitro Cell Toxicity and Intracellular Uptake of Doxorubicin Exposed as a Solution or Liposomes: Implications for Treatment of Hepatocellular Carcinoma.

Cytostatic effects of doxorubicin in clinically applied doses are often inadequate and limited by systemic toxicity. The main objective of this in vitro study was to determine the anti-tumoral effect (IC50) and intracellular accumulation of free and liposomal doxorubicin (DOX) in four human cancer cell lines (HepG2, Huh7, SNU449 and MCF7). The results of this study showed a correlation between longer DOX exposure time and lower IC50 values, which can be attributed to an increased cellular uptake and intracellular exposure of DOX, ultimately leading to cell death. We found that the total intracellular concentrations of DOX were a median value of 230 times higher than the exposure concentrations after exposure to free DOX. The intracellular uptake of DOX from solution was at least 10 times higher than from liposomal formulation. A physiologically based pharmacokinetic model was developed to translate these novel quantitative findings to a clinical context and to simulate clinically relevant drug concentration–time curves. This showed that a liver tumor resembling the liver cancer cell line SNU449, the most resistant cell line in this study, would not reach therapeutic exposure at a standard clinical parenteral dose of doxorubicin (50 mg/m2), which is serious limitation for this drug. This study emphasizes the importance of in-vitro to in-vivo translations in the assessment of clinical consequence of experimental findings.

Amorphous Solid Dispersion Tablets Overcome Acalabrutinib pH Effect in Dogs.

Calquence® (crystalline acalabrutinib), a commercially marketed tyrosine kinase inhibitor (TKI), exhibits significantly reduced oral exposure when taken with acid-reducing agents (ARAs) due to the low solubility of the weakly basic drug at elevated gastric pH. These drug–drug interactions (DDIs) negatively impact patient treatment and quality of life due to the strict dosing regimens required. In this study, reduced plasma drug exposure at high gastric pH was overcome using a spray-dried amorphous solid dispersion (ASD) comprising 50% acalabrutinib and 50% hydroxypropyl methylcellulose acetate succinate (HPMCAS, H grade) formulated as an immediate-release (IR) tablet. ASD tablets achieved similar area under the plasma drug concentration–time curve (AUC) at low and high gastric pH and outperformed Calquence capsules 2.4-fold at high gastric pH in beagle dogs. In vitro multicompartment dissolution testing conducted a priori to the in vivo study successfully predicted the improved formulation performance. In addition, ASD tablets were 60% smaller than Calquence capsules and demonstrated good laboratory-scale manufacturability, physical stability, and chemical stability. ASD dosage forms are attractive for improving patient compliance and the efficacy of acalabrutinib and other weakly basic drugs that have pH-dependent absorption.

Pharmacokinetic studies of ginsenosides Rk1 and Rg5 in rats by UFLC–MS/MS

A rapid ultra-fast liquid chromatography tandem mass spectrometry method was developed and validated to determine ginsenosides Rk1 and Rg5, a pair of isomers, in rat plasma, which was successfully applied to their pharmacokinetic studies. Two ginsenosides were given to male Sprague-Dawley rats via intragastrical and intravenous routes, respectively, and the impact of double bond position on the pharmacokinetic features of the two ginsenosides was elucidated in rats. Ginsenoside Rg3 was used as internal standard and ethyl acetate was applied to extract analytes and internal standard. Chromatographic separation was carried out on a reverse-phase UPLC HSS T3 column (100 × 2.1 mm, 1.8 μm). The flow rate was set to 0.4 ml/min. The fragmentation transition was m/z 765.4 → m/z 101.1 for two ginsenosides. The mobile phases were composed of 0.1% formic acid aqueous solution and acetonitrile. The linear range was 2-1,000 ng/ml for the two ginsenosides. Intra- and inter-day precisions were <11.67%, and accuracy fluctuated from -7.44 to 6.78%. The extraction recovery, matrix effect and stability were within acceptable levels. After treatment with ginsenosides Rk1 and Rg5, some differences were found in their pharmacokinetic profiles in rats. The maximum plasma drug concentration and the area under the plasma drug concentration-time curve of ginsenoside Rg5 were about 5 times bigger than those of ginsenoside Rk1 after oral administration, and 3 times higher after intravenous administration. The oral bioavailabilities of ginsenosides Rk1 and Rg5 were 0.67 and 0.97%, respectively. The results indicated that ∆20(22) -ginsenosides showed better pharmacokinetic features than ∆20(21) -ginsenosides with the same glycosylation.

Hot-Melt Extruded Amorphous Solid Dispersion for Solubility, Stability, and Bioavailability Enhancement of Telmisartan.

Telmisartan (TEL, an antihypertensive drug) belongs to Class II of the Biopharmaceutical Classification System (BCS) because of its poor aqueous solubility. In this study, we enhanced the solubility, bioavailability, and stability of TEL through the fabrication of TEL-loaded pH-modulated solid dispersion (TEL pHM-SD) using hot-melt extrusion (HME) technology. We prepared different TEL pHM-SD formulations by varying the ratio of the drug (TEL, 10–60% w/w), the hydrophilic polymer (Soluplus®, 30–90% w/w), and pH-modifier (sodium carbonate, 0–10% w/w). More so, the tablets prepared from an optimized formulation (F8) showed a strikingly improved in vitro dissolution profile (~30-fold) compared to the free drug tablets. The conversion of crystalline TEL to its amorphous state is observed through solid-state characterizations. During the stability study, F8 tablets had a better stability profile compared to the commercial product with F8, showing higher drug content, low moisture content, and negligible physical changes. Moreover, compared to the TEL powder, in vivo pharmacokinetic studies in rats showed superior pharmacokinetic parameters, with maximum serum concentration (Cmax) and area under the drug concentration–time curve (AUC0–∞) of the TEL pHM-SD formulation increasing by 6.61- and 5.37-fold, respectively. Collectively, the results from the current study showed that the inclusion of a hydrophilic polymer, pH modulator, and the amorphization of crystalline drugs in solid dispersion prepared by HME can be an effective strategy to improve the solubility and bioavailability of hydrophobic drugs without compromising the drug’s physical stability.

Pharmacokinetics/Pharmacodynamics Evaluation of Flomoxef against Extended-Spectrum Beta-Lactamase-Producing Escherichia coli In Vitro and In Vivo in a Murine Thigh Infection Model.

Although flomoxef (FMOX) has attracted substantial attention as an antibiotic against extended-spectrum beta-lactamase-producing Escherichia coli (ESBL-producing E. coli), the pharmacokinetics/pharmacodynamics (PK/PD) characteristics of FMOX against ESBL-producing E. coli is unclear. The aim of this study was to determine the PK/PD index of FMOX against ESBL-producing E. coli. In vitro time-kill curve studies and in vivo PK/PD experiments were carried out. Time-kill curves exhibited a unique bactericidal activity: time-dependent activity at low concentrations and concentration-dependent activity at high concentrations. In neutropenic murine thigh infection experiments, the antibacterial activity of FMOX correlated with the time that the free drug concentration remaining above the minimum inhibitory concentration (MIC) (fT>MIC) and the ratio of the area under the free drug concentration-time curve for a 24h period to the MIC (fAUC24/MIC). However, the burden of ESBL producing E. coli significantly reduced when the time intervals for administration were shorter among three dosage regimens with same magnitude of fAUC24/MIC, indicating that fT>MIC is significant PK/PD index. The target value of fT>MIC for 1 log10 kill reduction was 35.1%. fT>MIC is the most significant PK/PD index of FMOX against ESBL-producing E. coli and its target value is ≥ 40%.

Effects Of Korean Red Ginseng On The Pharmacokinetics And Pharmacodynamics Of Metformin In Healthy Subjects

Characterizing potential interactions between red ginseng, an herb with desirable health effects, and metformin, a commonly used drug for the treatment of type 2 diabetes mellitus, is of high clinical importance. In this study, we evaluate the effects of Korean red ginseng on the pharmacokinetic and pharmacodynamic properties of metformin in healthy subjects. The study was conducted in an open-label, two-period and single-sequence design. A total of 11 subjects received multiple doses of metformin in the first study period followed by multiple doses of metformin and red ginseng in the second study period. The Geometric Mean Ratio (GMR) (90% Confidence Interval (CI)) between the groups for area under the plasma drug concentration-time curve within a dosing interval (tau) at steady state (AUCtau,ss) of metformin was out of the range of bioequivalence, indicating that the systemic exposure of metformin when combined with red ginseng was reduced compared with administration of metformin alone. However, the pharmacodynamic analysis showed that the GMR (90% CI) between the groups for area under the blood glucose values–time curve from time zero to the time of the last measurable value (AUClast) and maximum blood glucose value (Gmax) were within the range of bioequivalence. We concluded that the observed reduction in the systemic exposure of metformin when administered with red ginseng is clinically insignificant. This study demonstrated that Korean red ginseng did not have clinically significant pharmacokinetic or pharmacodynamic herb–drug interactions with metformin in healthy subjects.

Cumulative Fraction of Response for Once- and Twice-Daily Delamanid in Patients with Pulmonary Multidrug-Resistant Tuberculosis.

Pharmacokinetic (PK) and pharmacodynamic (PD) analyses were conducted to determine the cumulative fraction of response (CFR) for 100 mg twice-daily (BID) and 200 mg once-daily (QD) delamanid in patients with multidrug-resistant tuberculosis (MDR-TB), using a pharmacodynamic target (PDT) that achieves 80% of maximum efficacy. First, in the mouse model of chronic TB, the PK/PD index for delamanid efficacy was determined to be area under the drug concentration-time curve over 24 h divided by MIC (AUC0-24/MIC), with a PDT of 252. Second, in the hollow-fiber system model of tuberculosis, plasma-equivalent PDTs were identified as an AUC0-24/MIC of 195 in log-phase bacteria and 201 in pH 5.8 cultures. Third, delamanid plasma AUC0-24/MIC and sputum bacterial decline data from two early bactericidal activity trials identified a clinical PDT of AUC0-24/MIC of 171. Finally, the CFRs for the currently approved 100-mg BID dose were determined to be above 95% in two MDR-TB clinical trials. The CFR for the 200-mg QD dose, evaluated in a trial in which delamanid was administered as 100 mg BID for 8 weeks plus 200 mg QD for 18 weeks, was 89.3% based on the mouse PDT and >90% on the other PDTs. QTcF (QTc interval corrected for heart rate by Fridericia's formula) prolongation was approximately 50% lower for the 200 mg QD dose than the 100 mg BID dose. In conclusion, while CFRs of 100 mg BID and 200 mg QD delamanid were close to or above 90% in patients with MDR-TB, more-convenient once-daily dosing of delamanid is feasible and likely to have less effect on QTcF prolongation.

Model-Informed Drug Development for Antimicrobials: Translational PK and PK/PD Modeling to Predict an Efficacious Human Dose for Apramycin.

Apramycin represents a subclass of aminoglycoside antibiotics that has been shown to evade almost all mechanisms of clinically relevant aminoglycoside resistance. Model‐informed drug development may facilitate its transition from preclinical to clinical phase. This study explored the potential of pharmacokinetic/pharmacodynamic (PK/PD) modeling to maximize the use of in vitro time‐kill and in vivo preclinical data for prediction of a human efficacious dose (HED) for apramycin. PK model parameters of apramycin from four different species (mouse, rat, guinea pig, and dog) were allometrically scaled to humans. A semimechanistic PK/PD model was developed from the rich in vitro data on four Escherichia coli strains and subsequently the sparse in vivo efficacy data on the same strains were integrated. An efficacious human dose was predicted from the PK/PD model and compared with the classical PK/PD index methodology and the aminoglycoside dose similarity. One‐compartment models described the PK data and human values for clearance and volume of distribution were predicted to 7.07 L/hour and 26.8 L, respectively. The required fAUC/MIC (area under the unbound drug concentration‐time curve over MIC ratio) targets for stasis and 1‐log kill in the thigh model were 34.5 and 76.2, respectively. The developed PK/PD model predicted the efficacy data well with strain‐specific differences in susceptibility, maximum bacterial load, and resistance development. All three dose prediction approaches supported an apramycin daily dose of 30 mg/kg for a typical adult patient. The results indicate that the mechanistic PK/PD modeling approach can be suitable for HED prediction and serves to efficiently integrate all available efficacy data with potential to improve predictive capacity.

Preparation, Characterization and Pharmacokinetic Study of N-Terminal PEGylated D-Form Antimicrobial Peptide OM19r-8.

Recently, new cationic antibacterial peptide OM19R has been designed with low minimum inhibitory concentration (MIC) values against some gram-negative bacteria, such as Escherichia coli, Salmonella, and Shigella. However, this hybrid peptide, like most antibacterial peptides, has low enzyme stability and short half-life, which, in turn, increases the drug's cost. In this study, an antibacterial peptide (OM19r-8) was obtained containing some D-Arg amino acids. The new preparations were carried out through the replacement of l-Arginine by d-Arginine and the addition of PEG chains. Firstly, eight OM19r series of antibacterial peptides were obtained by designing D-Arg. Then, a polyethylene glycol-modified product mPEG5-butyrALD-OM19r-8 (mPEG5-OM19r-8) was isolated and purified by reverse-phase high-performance liquid chromatography (RT-HPLC). The enzyme stability test showed that the resistance of antibacterial peptide OM19r-8 to protease degradation increased by 4-32-fold. Moreover, the Time-kill studies showed that the germicidal kinetics curves of mPEG5-OM19r-8 and OM19r-8 to Escherichia coli had a similar trend, thus suggesting that PEG modification has an acceptable effect on the activity of the original peptide. Furthermore, the elimination of half-life (28.09±2.81min) of mPEG5-OM19r-8, and the area under the drug concentration-time curve (2686.48±651.36min∗ug/ml) was significantly prolonged. The current study demonstrates an example that optimizes the AMP by utilizing L-to-D amino acid replacement and including PEG chains. These results provide useful data for the clinical application of the mPEG5-OM19r-8.

Evidence of Microbiome-Drug Interaction between the Antimalarial Lumefantrine and Gut Microbiota in Mice.

The antimalarial drug lumefantrine exhibits erratic pharmacokinetics. Intersubject variability might be attributed, in part, to differences in gut microbiome-mediated drug metabolism. We assessed lumefantrine disposition in healthy mice stratified by enterotype to explore associations between the gut microbiota and lumefantrine pharmacokinetics. Gut microbiota enterotypes were classified according to abundance and diversity indices from 16S rRNA sequencing. Pharmacokinetic parameters were computed using noncompartmental analysis. Two distinct enterotypes were identified. Maximal concentration (C max) and total drug exposure measured as the area under the drug concentration-time curve (AUC0-24) differed significantly between the groups. The mean and standard deviation of C max were 660 ± 220 ng/mL versus 390 ± 59 ng/mL (P = 0.02), and AUC0-24 was 9,600 ± 2,800 versus 5,800 ± 810 ng × h/mL (P = 0.01). In healthy mice intragastrically dosed with the antimalarial drug lumefantrine in combination with artemether, lumefantrine exposure was associated with gut bacterial community structure. Studies of xenobiotic-microbiota interactions can inform drug posology and elucidate mechanisms of drug disposition.

Pharmacokinetic/pharmacodynamic and safety study of a single dose of evolocumab 140 mg in healthy Chinese subjects.

Evolocumab, a human monoclonal antibody that binds to proprotein convertase subtilisin/kexin type 9 (PCSK9), markedly reduces low-density lipoprotein cholesterol (LDL-C). Here we characterize the pharmacokinetics, pharmacodynamics, safety, and tolerability of evolocumab manufactured at a new site administered in healthy Chinese subjects. This phase 1 study of a single subcutaneous 140-mg dose of evolocumab was conducted in healthy subjects of Chinese descent residing in Hong Kong. Subjects were followed through day 85. 20 subjects (all men) were enrolled. Mean (SD) age was 26.6 (8.5) years; baseline LDL-C was 2.4 (0.7) mmol/L. Mean (SD) evolocumab maximum serum concentration (Cmax) was 14.1 (5.0) μg/mL; area under the serum drug concentration-time curve from time 0 to time of last quantifiable concentration (AUClast) was 178 (80) day×μg/mL; AUC from time 0 to infinity (AUCinf) was 187 (80) day×μg/mL; terminal half-life was 5.95 (1.76) days; median time to reach Cmax (tmax) was 4.0 days. Maximum LDL-C decrease (-57.5%) was observed on day 15 and recovered to baseline by day 57. The most common adverse events (AEs) were nasal congestion (20%), oropharyngeal pain (15%), sneezing (15%), cough (10%), upper respiratory tract infection (10%), and diarrhea (10%). Most AEs were isolated incidences of mild severity, with no serious or treatment-related events. No anti-evolocumab antibodies were detected. A single 140-mg dose of evolocumab manufactured at the new site and administered in healthy Chinese subjects was associated with typical antibody pharmacokinetics, rapid and reversible decreases in LDL-C, and no new safety events.

Population Pharmacokinetics of Linezolid in Tuberculosis Patients: Dosing Regimen Simulation and Target Attainment Analysis.

The prolonged treatment duration for multidrug-resistant tuberculosis (MDR-TB) makes linezolid dosing difficult because of adverse effects associated with long-term use. We sought to find the optimal dosing regimen for linezolid across different MIC values. Pharmacokinetic (PK) data from TB patients were included from Brazil, Georgia, and two U.S. sites. Population PK modeling and simulation were performed. We used an fAUC (area under the unbound drug concentration-time curve)/MIC ratio of >119 as the PK/pharmacodynamic (PD) target and minimum (trough) concentrations of drug (Cmins) of 2 and 7 mg/liter as thresholds for toxicity. The PK/PD breakpoint was defined as the highest MIC at which the probability of target attainment is >90%. A total of 104 patients with pulmonary TB were included, with a median age and weight of 37 years and 60 kg. Eighty-one percent had drug-resistant TB. The PK data were best described by a one-compartment model. The PK/PD breakpoint was 0.125 mg/liter for a total daily dose of 300 mg, while daily doses of 450 to 600 mg and 900 to 1,200 mg had PK/PD breakpoints of 0.25 and 0.50 mg/liter, respectively. The probability of achieving a Cmin of ≤2 mg/liter was higher when the dose was given at once than when dividing it into 2 doses. Linezolid at a daily dose of 300 mg may not be optimal. We predicted an excellent and comparable efficacy of linezolid using total daily doses of 900 and 1,200 mg for MICs of ≤0.5 mg/liter but with the potential for more toxicity than with 600 mg daily. The increase in Cmin was noticeable when the daily dose was divided and may incur greater toxicity.

Evaluation of Intravenous Fosfomycin Disodium Dosing Regimens in Critically Ill Patients for Treatment of Carbapenem-Resistant Enterobacterales Infections Using Monte Carlo Simulation.

There are limited intravenous fosfomycin disodium (IVFOS) dosing regimens to treat carbapenem-resistant Enterobacterales (CRE) infections. This study aimed to use Monte Carlo simulation (MCS) for evaluation of IVFOS dosing regimens in critically ill patients with CRE infections. The dosing regimens in critically ill patients with various creatinine clearance were evaluated with MCS using minimum inhibitory concentration (MIC) distributions of fosfomycin against CRE clinical isolates in Thailand and the 24 h area under the plasma drug concentration–time curve over the minimum inhibitory concentration (AUC0-24/MIC) of ≥21.5 to be a target for IVFOS. The achieved goal of the probability of target attainment (PTA) and a cumulative fraction of response (CFR) were ≥90%. A total of 129 non-duplicated CRE clinical isolates had MIC distributions from 0.38 to >1024 mg/L. IVFOS 8 g every 8 h, 1 h, or 4 h infusion, could achieve approximately 90% PTA of AUC0-24/MIC target to treat CRE infections with MICs ≤ 128 mg/L. According to PTA target, an IVFOS daily dose to treat carbapenem-resistant Escherichia coli based on Clinical Laboratory Standards Institute (CLSI) breakpoints for urinary tract infections and one to treatment for CRE infections based on the European Committee on Antimicrobial Susceptibility Testing (EUCAST) breakpoints were 16 g/day and 8 g/day, respectively. All dosing regimens of IVFOS against CRE achieved CFR ≤ 70%. This study proposes the IVFOS dosing regimens based on CLSI and EUCAST breakpoints for the treatment of CRE infections. However, further clinical studies are needed to confirm the results of these findings.

Pharmacodynamic Evaluation of MRX-8, a Novel Polymyxin, in the Neutropenic Mouse Thigh and Lung Infection Models against Gram-Negative Pathogens.

MRX-8 is a novel polymyxin analogue in development for the treatment of infections caused by Gram-negative pathogens, including those resistant to other antibiotic classes. In the present study, we examined the pharmacodynamic activity of MRX-8 against a variety of common Gram-negative pathogens in the neutropenic mouse thigh and lung models. Additionally, we examined polymyxin B (PMB) as a comparator. Plasma pharmacokinetics of MRX-8 and PMB were linear over a broad dosing range of 0.156 to 10 mg/kg of body weight and had similar AUC0-∞ (area under the drug concentration-time curve from 0 h to infinity) exposures of MRX-8, 0.22 to 12.64 mg · h/liter, and PMB, 0.12 to 13.22 mg · h/liter. Dose fractionation was performed for MRX-8 using a single Escherichia coli isolate, and the results demonstrated that both Cmax (maximum concentration of drug in serum)/MIC and AUC/MIC ratios were strongly associated with efficacy. In the thigh model, dose-ranging studies included strains of E. coli (n = 3), Pseudomonas aeruginosa (n = 2), Klebsiella pneumoniae (n = 3), and Acinetobacter baumannii (n = 1). Both MRX-8 and PMB exhibited increased effects with increasing doses. MRX-8 and PMB free AUC/MIC exposures for net stasis were similar for E. coli and K. pneumoniae at 20 to 30. Notably, for P. aeruginosa and A. baumannii, the free AUC/MIC ratio for stasis was numerically much smaller for MRX-8 at 6 to 8 than for PMB at 16 to 37. In the lung model, MRX-8 was also more effective than PMB when dosed to achieve similar free-drug AUC exposures over the study period. MRX-8 is a promising novel polymyxin analogue with in vivo activity against many different clinically relevant species in both the mouse thigh and lung models.