Drift Tube Ion Mobility Research Articles

Continuous fiber printing of a modular heater for ion mobility spectrometry

Ion mobility spectrometry (IMS) is a powerful analytical method for separating and detecting gaseous substances like volatile organic compounds (VOCs). It is highly versatile, used both as a standalone technique and in combination with chromatographic methods for pre-separation or mass spectrometry for complex matrix analysis. This study explores the use of an advanced 3D printing technology to print a heater for an IMS-device.A continuous fiber printer, commonly used to enhance the mechanical properties of printed objects, was used to create a customized heating element by embedding a copper wire within the polymer matrix during the printing process. Cyclic olefin copolymer (COC) was chosen as the matrix material due to its analytical properties, such as low off-gassing and higher thermal stability, compared to the more commonly used polylactic acid (PLA).The 3D printed heater was incorporated into a drift tube ion mobility spectrometer, and its performance was evaluated by analyzing the separation of various ketones. The results show that the 3D printed heater effectively controlled the temperature within the drift tube, improving the resolving power of overlapping peaks.This study shows the potential of 3D printing technology to improve fabrication and functionality of IMS devices. The flexibility in design and material selection afforded by 3D printing not only enhances the analytical performance of IMS but also allows for customization and rapid prototyping of other analytical instruments or laboratory devices.

Conservation of the Charge in Signal from Drift Tube Ion Mobility Spectrometers.

Quantitative information obtained from drift tube detectors used in ion mobility spectrometry is contained in the area of peaks forming the drift time spectrum. The area of all peaks corresponds to the total charge of ions entering the drift section of the spectrometer. It was found that this charge is not conserved when the ion composition changes. This work is devoted to studying the causes of this phenomenon. Experimental research consisted of recording drift time spectra for 2-pentanone and n-heptanone, at various analyte concentrations and different opening times of the shutter grid. Measurements of the total ion current were also performed in static mode with an open grid. The research results indicated that the reasons for the lack of ion charge conservation in the drift time spectrum are ion recombination, mutual repulsion, and mobility-dependent transmission of ions through the shutter grid. The explanation of the relationships obtained experimentally was based on a simple theoretical model, which considered the phenomenon of ion transport along the reaction section and the penetration of ions through the shutter. The developed model provides a good description of the measurement results and allows the estimation of ion currents and ion concentrations in the reaction section upstream of the grid. This information is important for proper quantitative analysis as well as when the ion mobility spectrometer is used in quantitative studies of chemical ionization processes.

High Resolving Power Electrospray Ionization Ion Mobility Spectrometer Based on Fourier Deconvolution Multiplexing.

The resolving power of the drift tube ion mobility spectrometry (IMS) is mainly dependent on the drift length, the drift voltage, the pulse width of an ion gate, and the pressure inside the drift tube. Electrospray ionization (ESI)-IMS is a highly sensitive and reliable technique for the detection and analysis of nonvolatile compounds, and high resolving power is necessary to separate structurally similar compounds. To improve the analytical performance of atmospheric pressure ESI-IMS, the Fourier deconvolution (FD) multiplexing technique is investigated as an effective and convenient means to improve the resolving power as well as the signal-to-noise ratio. By reducing the equivalent ion gate opening width to 5 μs using a typical Tyndall-Powell ion shutter, a high resolving power RP up to 170 can be achieved with a drift length of 12 cm and a drift voltage of 10 kV. Rhodamine 6G (R6G), sodium dodecyl sulfate (SDS), methacycline, oxytetracycline, and ractopamine were evaluated using the FD-ESI-IMS, and mixtures with similar ion mobility can be well separated without prolonging the drift length.

Computer Vision-Assisted Robotized Sampling of Volatile Organic Compounds.

In conventional chemical analysis, samples are homogenized, extracted, purified, and injected into an analytical instrument manually or with a certain degree of automation. Such complex methods can provide superior performance in terms of sensitivity or selectivity. However, in some cases, it would be advantageous to possess a method that circumvents those preparatory steps, which require much attention. Here, we present a facile analytical approach to sampling volatile organic compounds (VOCs). Solid specimens emitting VOCs can be dropped onto the drop-off zone at a random position without any special alignment. A computer vision system recognizes specimen position, and a robotic arm places a sampling probe in the proximity of the specimen. The probe aspirates the VOCs─emitted by the specimen─with the aid of a suction force. A portion of the gaseous extract is transferred to the tritium-based ion source of a drift-tube ion mobility spectrometer. The ion mobility spectrum is immediately displayed in the customized graphical user interface (GUI). The sampling system also features a function for flushing extract ducts with hot nitrogen gas. Multiple specimens can be dropped for analysis at the same time. In one embodiment, the system can distinguish fresh meat from spoiled meat. When two meat specimens are placed on the drop-off zone, they are immediately sampled by the robotic arm, analyzed, and labeled on the digital image displayed on the GUI. Thus, the developed autosampling platform provides a hassle-free way of qualitative or semiquantitative analysis of raw specimens.

Advancing Protein Analysis: A Low-Pressure Drift Tube Orbitrap Mass Spectrometer for Ultraviolet Photodissociation-Based Structural Characterization.

Owing to its ability to generate extensive fragmentation of proteins, ultraviolet photodissociation (UVPD) mass spectrometry (MS) has emerged as a versatile ion activation technique for the structural characterization of native proteins and protein complexes. Interpreting these fragmentation patterns provides insight into the secondary and tertiary structures of protein ions. However, the inherent complexity and diversity of proteins often pose challenges in resolving their numerous conformations. To address this limitation, we combined UVPD-MS with drift tube ion mobility, offering potential to acquire conformationally selective MS/MS information. A low-pressure drift tube (LPDT) Orbitrap mass spectrometer equipped with 193 nm UVPD capabilities enables the analysis of protein conformers through the analysis of arrival time distributions (ATDs) of individual fragment ions. ATDs of fragment ions are compared for different backbone cleavage sites of the protein or different precursor charge states to give information about regions of potential folding or elongation. This integrated platform offers promise for advancing our understanding of protein structures in the gas phase.

Recent additions and access to a multidimensional lipidomic database containing liquid chromatography, ion mobility spectrometry, and tandem mass spectrometry information.

The importance of lipids in biology continues to grow with their recent linkages to more diseases and conditions, microbiome fluctuations, and environmental exposures. These associations have motivated researchers to evaluate lipidomic changes in numerous matrices and studies. Lipidomic analyses, however, present numerous challenges as lipid species have broad chemistries that require different extraction methods and instrumental analyses to evaluate and separate their many isomers and isobars. Increasing knowledge about different lipid characteristics is therefore crucial for improving their separation and identification. Here, we present a multidimensional database for lipids analyzed on a platform combining reversed-phase liquid chromatography, drift tube ion mobility spectrometry, collision-induced dissociation, and mass spectrometry (RPLC-DTIMS-CID-MS). This platform and the different separation characteristics it provides enables more confident lipid annotations when compared to traditional tandem mass spectrometry platforms, especially when analyzing highly isomeric molecules such as lipids. This database expands on our previous publication containing only human plasma and bronchoalveolar lavage fluid lipids and provides experimental RPLC retention times, IMS collision cross section (CCS) values, and m/z information for 877 unique lipids from additional biofluids and tissues. Specifically, the database contains 1504 precursor [M + H]+, [M + NH4]+, [M + Na]+, [M-H]-, [M-2H]2-, [M + HCOO]-, and [M + CH3COO]- ion species and their associated CID fragments which are commonly targeted in clinical and environmental studies, in addition to being present in the chloroform layer of Folch extractions. Furthermore, this multidimensional RPLC-DTIMS-CID-MS database spans 5 lipid categories (fatty acids, sterols, sphingolipids, glycerolipids, and glycerophospholipids) and 24 lipid classes. We have also created a webpage (tarheels.live/bakerlab/databases/) to enhance the accessibility of this resource which will be populated regularly with new lipids as we identify additional species and integrate novel standards.

An Untargeted Lipidomics Workflow Incorporating High-Resolution Demultiplexing (HRdm) Drift Tube Ion Mobility-Mass Spectrometry.

Global discovery lipidomics can provide comprehensive chemical information toward understanding the intricacies of metabolic lipid disorders such as dyslipidemia; however, the isomeric complexity of lipid species remains an analytical challenge. Orthogonal separation strategies, such as ion mobility (IM), can be inserted into liquid chromatography-mass spectrometry (LC-MS) untargeted lipidomic workflows for additional isomer separation and high-confidence annotation, and the emergence of high-resolution ion mobility (HRIM) strategies provides marked improvements to the resolving power (Rp > 200) that can differentiate small structural differences characteristic of isomers. One such HRIM strategy, high-resolution demultiplexing (HRdm), utilizes multiplexed drift tube ion mobility spectrometry (DTIMS) with post-acquisition algorithmic deconvolution to access high IM resolutions while retaining the measurement precision inherent to the drift tube technique; however, HRdm has yet to be utilized in untargeted studies. In this manuscript, a proof-of-concept study using ATP10D dysfunctional murine models was investigated to demonstrate the utility of HRdm-incorporated untargeted lipidomic analysis pipelines. Total lipid features were found to increase by 2.5-fold with HRdm compared to demultiplexed DTIMS as a consequence of more isomeric lipids being resolved. An example lipid, PC 36:5, was found to be significantly higher in dysfunctional ATP10D mice with two resolved peaks observed by HRdm that were absent in both the functional ATP10D mice and the standard demultiplexed DTIMS acquisition mode. The benefits of utilizing HRdm for discerning isomeric lipids in untargeted workflows have the potential to enhance our analytical understanding of lipids related to disease complexity and biologically relevant studies.

Deciphering the Molecular Dance: Exploring the Dynamic Interplay Between Mouse Insulin B9-23 Peptides and their Variants.

Type 1 diabetes results from the autoimmune destruction of pancreatic insulin-producing β-cells, primarily targeted by autoreactive T cells that recognize insulin B9-23 peptides as antigens. Using drift tube ion mobility spectrometry-mass spectrometry, transmission electron microscopy, and two-dimensional infrared spectroscopy, we characterized mouse insulin 1 B9-23 (Ins1 B9-23), insulin 2 B9-23 (Ins2 B9-23), along with two of their mutants, Ins2 B9-23 Y16A and Ins2 B9-23 C19S. Our findings indicate that Ins1 B9-23 and the Ins2 Y16A mutant exhibit rapid fibril formation, whereas Ins2 B9-23 and the Ins2 C19S mutant show slower fibrillization and a structural rearrangement from globular protofibrils to fibrillar aggregates. These differences in aggregation behaviors also manifest in interactions with (-)epigallocatechin gallate (EGCG), a canonical amyloid inhibitor. EGCG effectively disrupts the fibrils formed by Ins1 B9-23 and the Y16A mutant. However, it proves ineffective in preventing fibril formation of Ins2 B9-23 and the C19S mutant. These results establish a strong correlation between the aggregation behaviors of these peptides and their divergent effects on anti-islet autoimmunity.

Trapped and drift-tube ion-mobility spectrometry for the analysis of environmental contaminants: Comparability of collision cross-section values and resolving power.

Ion-mobility (IM)-derived collision cross-section (CCS) values can serve as a valuable additional identification parameter within suspect and non-target screening studies of environmental contaminants. However, these applications require to assess the reproducibility of CCS calculations between different IM set-ups. Especially for the comparison of trapped and drift-tube IM (TIMS/DTIM) derived CCS values, data for environmental applications is lacking. The presented study assessed the bias of TIMS derived CCSN2 (TIMSCCSN2) values of 48 environmental contaminants from three classes in comparison to a previously established DTIM database. Based on two sets of isomeric bisphenols, the resolving power of both systems was compared, addressing the instrumental settings which influence the resolution of TIMS measurements. For 91% of the datapoints, bias between TIMSCCSN2 and DTCCSN2 values (latter set as reference) were < 2%, indicating a good inter-platform reproducibility. TIMS resolving power was dependent on the selected mobility window and ramping times whereby a resolution of up to 116 was achieved. Similar resolving power was observed for multiplexed DTIMS data if a high-resolution post-processing step was implemented. These results provide valuable insights in CCSN2 reproducibility facilitating database transfer in future TIMS based studies. Knowledge on the influence of acquisition settings on robustness of TIMSCCSN2 calculations and resolving power can ease method development supporting efficient development and reliable identifications of emerging environmental contaminants.

High-Resolution Drift Tube Ion Mobility Spectrometer with Ultra-Fast Polarity Switching.

Besides safety and security applications, ion mobility spectrometry (IMS) is increasingly used in other fields such as medicine, environmental monitoring and food quality analysis. However, some applications require gas chromatographic separation before analysis by IMS. Furthermore, different compounds in the sample may form positive or negative ions during ionization and therefore simultaneous detection of both ion polarities is highly beneficial to avoid two chromatographic runs of the same sample. This can be achieved by ultra-fast polarity switching of a single drift tube IMS, allowing for quasi-simultaneous detection of both ion polarities. By using a ramped aperture voltage during the switching process, we overcome the issue of excessive displacement currents at the detector during polarity switching, which usually lead to overdriving the output signal of the high-gain transimpedance amplifier. Furthermore, mechanical aperture grid oscillations caused by polarity switching were also reduced through the ramped aperture voltage. This enables a polarity switching time of only 7 ms at a drift voltage of 8 kV and a drift length of 103 mm, leading to a high resolving power of RP = 117. Requiring 50 ms to acquire a pair of positive and negative spectrum, the IMS achieves an acquisition rate of 20 Hz. It reaches limits of detection of 20 pptv for dimethyl methylphosphonate and 40 pptv for methyl salicylate. For demonstration, different hop varieties were investigated and could be clearly differentiated by considering both, the positive and negative spectra.

Accurate Collisional Cross Section Measurement by Multipass Cyclic Ion Mobility Spectrometry.

Ion mobility-mass spectrometry (IM-MS) is a powerful analytical tool for structural characterization. IM measurement provides collision cross section (CCS) values that facilitate analyte identification. While CCS values can be directly calculated from mobility measurements obtained using drift tube ion mobility spectrometry (DT-IMS), this method has limited mobility resolution due to the practical constraints on the length of the ion drift path. Consequently, DT-IMS cannot differentiate analytes with similar mobilities or resolve fine mobility features of individual ions. Cyclic IMS (cIMS) instruments leverage a cyclic path enabled by traveling wave ion mobility (TWIM) technology and offer increased mobility solution to address this challenge. While TWIM devices must first be calibrated to enable CCS measurements, current calibration strategies are primarily tailored for single-pass analyses. This preference is partly attributed to the challenges associated with multipass calibration methods, which require both calibrants and analytes to experience the same number of passes. Achieving this consistency can be complicated due to factors like peak splitting and diffusion, and may not be feasible for online IM-MS analyses. A recent report employed average ion velocities obtained from multiple measurements under different separation pathlengths as a path length-independent metric for CCS calibration. However, the ability to exploit this averaging approach is limited by observed variation in ion drift time/velocity in these measurements. In this study, we introduce a novel calibration strategy designed for multipass cIMS analyses, directly targeting the root cause for the path length- and mobility-dependent variations in ion drift time. With this method, we demonstrate that CCS values derived from multipass measurements closely align with those obtained from single-pass analyses, with an average deviation of 0.1%. We apply this method to characterize four isomeric trisaccharides. Our approach not only results in excellent agreement between our measured cIMSCCS values and the reported DTCCS values, with an average difference of only 0.5%, but also allows us to effectively identify subtle mobility characteristics of each compound and determine their respective CCS values. This level of detail and accuracy was previously unattainable using DT-IMS or single-pass cIMS measurements. We developed an algorithm for reconstructing arrival time distribution in cases where wrap-around has resulted in peak splitting. Collectively, the new calibration strategy and the reconstruction procedure maintain reproducibility and precision in CCS measurements while largely eliminating the need for meticulous selection of separation times. We expect that our method will empower researchers to harness the high mobility resolution offered by multipass cIMS analyses without compromising the accuracy of CCS measurement, making it appropriate for straightforward use across a wide range of applications.

Reliable Detection of Chemical Warfare Agents Using High Kinetic Energy Ion Mobility Spectrometry.

High Kinetic Energy Ion Mobility Spectrometers (HiKE-IMS) ionize and separate ions at reduced pressures of 10-40 mbar and over a wide range of reduced electric field strengths E/N of up to 120 Td. Their reduced operating pressure is distinct from that of conventional drift tube ion mobility spectrometers that operate at ambient pressure for trace compound detection. High E/N can lead to a field-induced fragmentation pattern that provides more specific structural information about the analytes. In addition, operation at high E/N values adds the field dependence of ion mobility as an additional separation dimension to low-field ion mobility, making interfering compounds less likely to cause a false positive alarm. In this work, we study the chemical warfare agents tabun (GA), sarin (GB), soman (GD), cyclosarin (GF) and sulfur mustard (HD) in a HiKE-IMS at variable E/N in both the reaction and the drift region. The results show that varying E/N can lead to specific fragmentation patterns at high E/N values combined with molecular signals at low E/N. Compared to the operation at a single E/N value in the drift region, the variation of E/N in the drift region also provides the analyte-specific field dependence of ion mobility as additional information. The accumulated data establish a unique fingerprint for each analyte that allows for reliable detection of chemical warfare agents even in the presence of interfering compounds with similar low-field ion mobilities, thus reducing false positives.

High-resolution ion mobility based on traveling wave structures for lossless ion manipulation resolves hidden lipid features

High-resolution ion mobility (resolving power > 200) coupled with mass spectrometry (MS) is a powerful analytical tool for resolving isobars and isomers in complex samples. High-resolution ion mobility is capable of discerning additional structurally distinct features, which are not observed with conventional resolving power ion mobility (IM, resolving power ~ 50) techniques such as traveling wave IM and drift tube ion mobility (DTIM). DTIM in particular is considered to be the “gold standard” IM technique since collision cross section (CCS) values are directly obtained through a first-principles relationship, whereas traveling wave IM techniques require an additional calibration strategy to determine accurate CCS values. In this study, we aim to evaluate the separation capabilities of a traveling wave ion mobility structures for lossless ion manipulation platform integrated with mass spectrometry analysis (SLIM IM-MS) for both lipid isomer standards and complex lipid samples. A cross-platform investigation of seven subclass-specific lipid extracts examined by both DTIM-MS and SLIM IM-MS showed additional features were observed for all lipid extracts when examined under high resolving power IM conditions, with the number of CCS-aligned features that resolve into additional peaks from DTIM-MS to SLIM IM-MS analysis varying between 5 and 50%, depending on the specific lipid sub-class investigated. Lipid CCS values are obtained from SLIM IM (TW(SLIM)CCS) through a two-step calibration procedure to align these measurements to within 2% average bias to reference values obtained via DTIM (DTCCS). A total of 225 lipid features from seven lipid extracts are subsequently identified in the high resolving power IM analysis by a combination of accurate mass-to-charge, CCS, retention time, and linear mobility-mass correlations to curate a high-resolution IM lipid structural atlas. These results emphasize the high isomeric complexity present in lipidomic samples and underscore the need for multiple analytical stages of separation operated at high resolution.Graphical abstract

Ion Mobility Separations Using Cocentric Architecture.

Ion mobility separations, especially using drift tube ion mobility spectrometers, are usually performed in linear channels, which can have a large footprint when extended to achieve higher resolving powers. In this work, we explored the performance of an ion mobility device with a curved architecture, which can have a more compact form. The cocentric ion mobility spectrometer (CoCIMS) manipulates ions between two cocentric surfaces containing a serpentine track. The mobility separation inside the CoCIMS is achieved using traveling waveforms (TWs). We initially evaluated the device using ion trajectory simulations using SIMION, which indicated that when ions traveled circularly inside the CoCIMS they resulted in similar resolving powers and transmitted m/z range as traveling in a straight path. We then performed experimental validation of the CoCIMS in conjunction with a TOF MS. The CoCIMS was made of two flexible printed circuit board materials folded into cocentric cylinders separated by a gap of 2.8 mm. The device was about 50 mm diameter ×152 mm long and provided 1.846 m of serpentine path length. Three sets of mixtures (Agilent tune mixture, tetraalkylammonium salts, and an eight-peptide mixture) and four traveling waveform profiles (square, sine, triangle, and sawtooth) were used. The sawtooth TW profile produced a slightly higher resolving power for the Agilent tuning mixture and tetraalkylammonium ions. The average resolving power for Agilent tune mixture ions ranged from 37 (using sawtooth TW) to 27 (using square TW). The average resolving powers ranged from 45 (sawtooth TW) to 31 (square TW) for tetraalkylammonium ions. The resolving power of the peptide mixture ions was similar among the four TW profiles and ranged from 51 to 56. The average percent error in TWCCS for the peptide mixture ions was about 0.4%. The new device showed promising results, but improvements are needed to further increase the resolving power.

Utilization of bis-MPA Dendrimers for the Calibration of Ion Mobility Collision Cross Section Calculations.

Ion mobility-mass spectrometry (IM-MS) has become increasingly popular with the rapid expansion of available techniques and instrumentation. To enable accuracy, standardization, and repeatability of IM-MS measurements, the community requires reliable and well-defined reference materials for calibration and tuning of the equipment. To address this need, synthetic dendrimers of high chemical and structural purity were tested on three ion mobility platforms as potential calibrants. First, synthesized dendrimers were characterized by drift tube ion mobility (DTIMS), using an Agilent 6560 IM-qTOF-MS to assess their drift tube collision cross section (DTCCS) values. Then, assessment of obtained CCS values on trapped ion mobility (TIMS) and traveling wave ion mobility (TWIMS) ion mobility platforms were compared to those found by DTIMS. Across all three systems, dendrimers were found to have high potential for m/z and ion mobility calibration in the CCS range of 160-1700 Å2. To further validate their use as calibrants, drift tube calculated CCS values for dendrimers were utilized to calibrate calculations of CCS for known standards including Agilent Tuning mix, the CCS Major mix from Waters, and SPLASH LIPIDOMIX. Additionally, structures of sodiated dendrimers were computated along with theoretical CCS values which showed good agreement with the experimental CCS values. On the basis of the results presented, we recommend the use of dendrimers as alternatives and/or complementary compounds to commonly used calibrants for ion mobility platforms.

Development of a Modular, Open-Source, Reduced-Pressure, Drift Tube Ion Mobility Spectrometer.

Toward the goal of minimizing construction costs while maintaining high performance, a new, reduced-pressure, drift tube ion mobility system is coupled with an ion trap mass analyzer through a custom ion shuttle. The availability of reduced-pressure ion mobility systems remains limited due to comparatively expensive commercial options and limited shared design features in the open literature. This report details the complete design and benchmarking characteristics of a reduced-pressure ion mobility system. The system is constructed from FR4 PCB electrodes and encased in a PTFE vacuum enclosure with custom torque-tightened couplers to utilize standard KF40 bulkheads. The PTFE enclosure directly minimizes the overall system expenses, and the implementation of threaded brass inserts allows for facile attachments to the vacuum enclosure without damaging the thermoplastic housing. Front and rear ion funnels maximize ion transmission and help mitigate the effects of radial ion diffusion. A custom planar ion shuttle transports ions from the exit of the rear ion funnel into the ion optics of an ion trap mass analyzer. The planar ion shuttle can couple the IM system to any contemporary Thermo Scientific ion trap mass analyzer. Signal stability and ion intensity remain unchanging following the implementation of the planar ion shuttle when compared to the original stacked ring ion guide. The constructed IM system showed resolving powers up to 85 for various small molecules and proteins using the Fourier transform from a ∼1 m drift tube. Recorded mobilities derived from first principles agree with published literature results with an average error of 1.1% and an average error toward literature values using single field calibration of <1.3%.

UV-A-Induced Photoisomerization and Photodimerization of Curcumin: An Ion Mobility Mass Spectrometry Study.

Curcumin, the bioactive compound present in spice plant turmeric, has been shown to exhibit selective phototoxic activities toward mammalian cancer cells, and it is being used extensively as a photosensitizer (PS) in photodynamic therapies (PDT). However, so far, the fate of curcumin toward photochemical transformations is not well understood. Here we report our findings of a number of novel photochemical reaction channels of curcumin in water-methanol mixture, like photoisomerization, photodimerization, and photooxidation (H2-loss). The reaction was performed by irradiating the curcumin solution with ultraviolet (UV) light of wavelength 350 nm, which is abundant in the earth's troposphere. Product identification and structure elucidation are done by employing an integrated method of drift tube ion mobility mass spectrometry (DTIMS) in combination with high-performance liquid chromatography (HPLC) and collision-induced dissociation (CID) of the mass-selected molecular ions. Two photoisomers of curcumin produced as a result of trans-cis configurational changes about C═C double bonds in the excited state have been identified, and it has been shown that they could serve as the precursors for formation of isomeric dimers via [2 + 2] cycloaddition and H2-loss products. Comparisons of the experimentally measured collision cross-section (CCS) values of the reactant and product ions obtained by the DTIMS method with those predicted by the electronic structure theory are found to be very effective for the discrimination of the produced photoisomers. The observed photochemical reaction channels are potentially significant toward uses of curcumin as a photosensitizer in photodynamic therapy.

Evaluation of Fourier deconvolution ion mobility spectrometer as high-performance gas chromatography detector for the analysis of plant extract flavors

The Fourier deconvolution ion mobility spectrometer (FDIMS) offers multiplexing and improves the resolving power and signal-to-noise ratio. To evaluate the FDIMS as a detector for gas chromatography for the analysis of complex samples, we connected a drift tube ion mobility spectrometer to a commercial gas chromatograph and compared the performance including resolving power, sensitivity, and linear range using 2,6-di‑tert-butylpyridine. Mixed standards were also injected into the tandem system to evaluate the performance under optimized conditions. A complex plant extract sample used as natural flavoring was investigated using the resulting system. The results show that the instrument implemented with the Fourier deconvolution multiplexing method demonstrated higher performance over the traditional signal averaging method including higher resolving power, better limit of detection, and wider linear range for a variety of compounds and natural plant extract flavorings.

Enhancing ion mobility spectrometry performance through a programmable ion swarm shaping method based on Bradbury-Nielsen gates

The ion gate is a critical element in drift tube ion mobility spectrometry (IMS) as it directly influences the resolving power and sensitivity of the system. However, the conventional Bradbury-Nielsen gate (BNG) often leads to deformation of the ion swarm shape, resulting in reduced resolving power and significant discrimination effects. To address these limitations, we propose a novel method that incorporates a cutting phase following the gate opening. This approach effectively reduces trailing edge deformation, resulting in a maximum resolving power of over 100 and increased signal intensity. Additionally, this method maintains high resolving power even during longer gate opening times. Remarkably, this method not only significantly reduces the mobility discrimination effect but also enables the achievement of reverse discrimination by adjusting the duration of the cutting phase. Consequently, it demonstrates the potential to selectively amplify the peak height of target ions. Our method offers straightforward implementation across all IMS systems utilizing the BNG, thereby significantly improving system performance.

Non-destructive, solvent-free quantification of wood preservatives in wood flour and wooden objects using GC-DTIMS

Qualitative and quantitative on-site detection methods for wood preservatives are of high value for the recycling industry and the occupational health and safety. Wood preservatives revealed as toxic to human and environment after decades of use. For the detection of contaminated wood and for processing of matured timber to particle boards a versatile detection method is needed. Especially historical wooden objects were treated with preservatives like pentachlorophenol, lindane or dichlorodiphenyltrichloroethane. This requires a non-destructive on-site detection method, that does not require specialized personnel. In this publication two methods are presented utilizing headspace sampling by solid-phase microextraction, subsequent separation using gas chromatography and detection by a drift tube ion mobility spectrometer (SPME–HS–GC-DTIMS). One method enables the quantitative detection of pentachlorophenol in wood flour and wood chips as they are used in wood processing industries. A limit of detection of 0.1 mg/kg was achieved using DIN 32645, which can be even more lowered. The second method enables non-destructive detection of pentachlorophenol, lindane, dichlorodiphenyltrichloroethane and other preservatives in wooden objects. Therefore, samples were prepared, which show a significantly lower concentration than typical treated objects, and used next to real samples for method validation. With the method contamination of the real samples and of the prepared samples of low concentration were proven.