Divertor Peak Heat Flux Research Articles

Realization of thousand-second improved confinement plasma with Super I-mode in Tokamak EAST

Mastering nuclear fusion, which is an abundant, safe, and environmentally competitive energy, is a great challenge for humanity. Tokamak represents one of the most promising paths toward controlled fusion. Obtaining a high-performance, steady-state, and long-pulse plasma regime remains a critical issue. Recently, a big breakthrough in steady-state operation was made on the Experimental Advanced Superconducting Tokamak (EAST). A steady-state plasma with a world-record pulse length of 1056 s was obtained, where the density and the divertor peak heat flux were well controlled, with no core impurity accumulation, and a new high-confinement and self-organizing regime (Super I-mode=I-mode+e-ITB) was discovered and demonstrated. These achievements contribute to the integration of fusion plasma technology and physics, which is essential to operate next-step devices.

Divertor plasma behaviors with neon seeding at different locations on EAST with ITER-like divertor

For the problem of excessively high divertor heat flux, active impurity seeding is an effective method to radiate the plasma energy reaching the divertor and thus achieve the divertor detachment. Neon is a very effective radiation impurity on many current tokamaks, which is also a candidate species to be applied on ITER. In the EAST 2019 experimental campaign, a series of experiments were performed by seeding a mixture of neon and deuterium (Ne-D2) for detachment and core-edge-divertor integration in H-mode plasmas. The divertor partial detachment with high-confinement core plasma has been achieved by using Ne-D2 seeding in EAST with ITER-like tungsten divertor. Both the plasma stored energy and H 98,y2 > 1.1 are maintained, with the divertor electron temperature, heat flux and the surface temperature near the strike point being all significantly reduced. The differences between Ne-D2 seeding at the scrape-off layer (SOL) upstream and downstream have been experimentally investigated in detail. It is found that impurity seeding at SOL downstream is more beneficial to reducing the divertor electron temperature and peak heat flux. By comparison with experiments using divertor D2 fueling, it is further demonstrated that gas seeding in the SOL downstream will enrich more particles near the strike point, while the seeding in the SOL upstream will influence the entire outer target more evenly. Furthermore, in most of the experiments, gas seeding does not cause obvious toroidal asymmetry in the divertor plasma. However, when D2 is injected in an amount similar to that used to build the plasma, it causes the particle flux near the gas-puff to increase locally, i.e., much more than that at the toroidal location far from the gas-puff location. It is a competition between particle source and transport. When the particle source is stronger, it will naturally increase the local particles. In addition, dedicated experiments with different poloidal distances between impurity seeding and strike point on the radiation ability were carried out. Both experimental results and SOLPS simulation show that the seeding close to the strike point is more conducive to neon ionization and energy radiation.

Impact of edge harmonic oscillations on the divertor heat flux in NSTX

Previously, edge-localized mode (ELM)-free and inter-ELM divertor peak heat flux reduction induced by an edge harmonic oscillation (EHO) was observed in NSTX [Gan et al., Nucl. Fusion 57, 126053 (2017)]. This paper introduces new analysis of the EHO impact on the divertor heat flux. It was found that enhanced edge turbulence significantly altered the divertor heat flux footprint in NSTX H-modes, relative to ELM-free discharges. When the background edge fluctuation level was low, the EHO significantly increased the heat flux width and decreased the divertor peak heat flux. When the background edge fluctuation level was high, the EHO actually increased the divertor peak heat flux. Furthermore, it was also found that the heat flux width increased with the increasing frequency of the EHO.

Active Radiative Liquid Lithium Divertor for Handling Transient High Heat Flux Events

The extreme heat flux anticipated in fusion reactor divertor plasma facing components (PFCs) is perhaps the most challenging technology issue for fusion energy development. Most divertor PFCs are designed based on the maximum steady-state operational limits. Application of lithium (Li) in NSTX resulted in improved H-mode confinement, H-mode power threshold reduction, and reduction in the divertor peak heat flux while maintaining essentially Li-free core plasma operation even during H-modes. These promising Li results in NSTX and related modeling calculations motivated the passive and active radiative liquid lithium divertor concepts (RLLD and ARLLD) (Ono et al. in Nucl Fusion 53:113030, 2013; Fusion Eng Des 89:2838, 2014). This radiative process has the desired effect of spreading the localized divertor heat load to the rest of the divertor chamber wall surfaces, facilitating divertor heat removal with relatively small amount of lithium ~ few moles/s to handle the expected steady-state high divertor heat load. However, in addition to the high steady-state heat flux, the fusion reactor divertor PFCs could also experience significant transient heat flux such as ELMs and/or other magnetic reconnection events which can deposit large transient heat flux onto the divertor PFCs. If unprotected, it could damage the divertor PFC surfaces which could lead to a highly undesirable unplanned shutdown for PFC repair and/or replacement. In this paper, we explore feasibility of LLD and ARLLD concepts in handling such transient heat flux to protect the divertor PFCs from the extreme transient heat flux while maintaining the normal plasma operations. We also suggest a possible implementation technique using inductive pellet injector for the reactor PFC protection from transient heat flux which can be tested on NSTX-U.

Progress of physics understanding for long pulse high-performance plasmas on EAST towards the steady-state operation of ITER and CFETR

Recently, the first ever 100 s long, steady-state H-mode discharge with good control of impurities, core and edge MHD stabilities, and heat exhaust was demonstrated in the Experimental Advanced Superconducting Tokamak (EAST) using the ITER-like (International Tokamak Experimental Reactor) tungsten upper divertor. Using both radio frequency (RF) power and neutral beam injection (NBI) heating, EAST has demonstrated fully non-inductive scenarios with an extension of fusion performance at high density and low rotation: β P ∼ 2.5, β N ∼ 2.0, H98,y2 ∼ 1.2, bootstrap current fraction fBS ∼50% at q95 ∼ 6.8. With pure RF power heating, plasmas have been maintained for up to 21 s (over 40 times the current relaxation time) with zero loop voltage and small edge localized modes (ELMs) at high density (ne/nGW ∼ 0.6–0.8), β P ∼ 2.0, β N ∼ 1.6, and ƒBS ∼47%. Experimental investigations show how plasma current profiles, turbulent transport and radiation properties self-consistently evolve toward fusion relevant steady state conditions. Modeling and physics experiments have confirmed the synergistic effects between electron cyclotron heating (ECH) and low hybrid wave (LHW), where ECH enhances the heating and current drive from LHW injection, enabling fully non-inductive operation at higher density. Small/no ELMs facilitate the RF power coupling in the H-mode phase and reduce divertor erosion. A low tungsten concentration was observed at high β P with a hollow profile in the core. Reduction of the peak divertor heat flux with f rad of up to 40% was compatible with the high β P scenario by using active radiation feedback control. With features such as dominant electron heating, zero/low NBI torque and an ITER-like tungsten divertor, fully non-inductive high-performance experiments on EAST offer unique contributions towards the succesful operation of ITER and CFETR (the Chinese Fusion Engineering Testing Reactor).

Simulation Study of Large Power Handling in the Divertor for CFETR Phase II

The Chinese Fusion Engineering Testing Reactor (CFETR) is a next fusion device proposed in China. The ability to exhaust the plasma power loss is a critical issue for the successful production of a fusion power reactor. For Phase II of CFETR with fusion power ~1 GW, the extremely large divertor heat load would be a severe challenge to achieve steady-state operation. In this paper, we have simulated the divertor performance by using SOLPS5.0 (B2.5-EIRENE) code package for a lower single null divertor configuration based on a core self-consistent steady-state scenario with Ar seeding. The core self-consistent steady-state scenario is calculated by a 1.5-D modeling workflow utilizing the One Modeling Framework for Integrated Tasks (OMFIT) framework. The modeling shows that Ar puffing from the lower divertor region together with D2 puffing from upstream is highly effective in mitigation of the divertor peak heat flux and temperature for the whole outer target and near strike point on the inner divertor target, however, electron and ion temperature ( $T_{e}$ and $T_{i})$ at far scrape-off layer on inner divertor is still higher than the erosion mitigation. In addition, comparison simulation of different divertor geometries has been performed in this paper. Further work on self-consistent core-edge coupling to estimate the effect of impurity seeding on core performance as well as the optimization of divertor geometry and operations will be studied.

Experimental study of heating scheme effect on the inner divertor power footprint widths in EAST lower single null discharges

A comprehensive work of the effects of plasma current and heating schemes on divertor power footprint widths is carried out in the experimental advanced superconducting tokamak (EAST). The divertor power footprint widths, i.e., the scrape-off layer heat flux decay length λq and the heat spreading S, are crucial physical and engineering parameters for fusion reactors. Strong inverse scaling of λq and S with plasma current have been demonstrated for both neutral beam (NB) and lower hybrid wave (LHW) heated L-mode and H-mode plasmas at the inner divertor target. For plasmas heated by the combination of the two kinds of auxiliary heating schemes (NB and LHW), the divertor power widths tend to be larger in plasmas with higher ratio of LHW power. Comparison between experimental heat flux profiles at outer mid-plane (OMP) and divertor target for NB heated and LHW heated L-mode plasmas reveals that the magnetic topology changes induced by LHW may be the main reason to the wider divertor power widths in LHW heated discharges. The effect of heating schemes on divertor peak heat flux has also been investigated, and it is found that LHW heated discharges tend to have a lower divertor peak heat flux compared with NB heated discharges under similar input power. All these findings seem to suggest that plasmas with LHW auxiliary heating scheme are better heat exhaust scenarios for fusion reactors and should be the priorities for the design of next-step fusion reactors like China Fusion Engineering Test Reactor.

Developing physics basis for the snowflake divertor in the DIII-D tokamak

Recent DIII-D results demonstrate that the snowflake (SF) divertor geometry (see standard divertor) enables significant manipulation of divertor heat transport for heat spreading and reduction in attached and radiative divertor regimes, between and during edge localized modes (ELMs), while maintaining good H-mode confinement. Snowflake divertor configurations have been realized in the DIII-D tokamak for several seconds in H-mode discharges with heating power –5 MW and a range of plasma currents MA. In this work, inter-ELM transport and radiative SF divertor properties are studied. Significant impact of geometric properties on SOL and divertor plasma parameters, including increased poloidal magnetic flux expansion, divertor magnetic field line length and divertor volume, is confirmed. In the SF-minus configuration, heat deposition is affected by the geometry, and peak divertor heat fluxes are significantly reduced. In the SF-plus and near-exact SF configurations, divertor peak heat flux reduction and outer strike point heat flux profile broadening are observed. Inter-ELM sharing of power and particle fluxes between the main and additional snowflake divertor strike points has been demonstrated. The additional strike points typically receive up to 10–15% of total outer divertor power. Measurements of electron pressure and poloidal beta support the theoretically proposed churning mode that is driven by toroidal curvature and vertical pressure gradient in the weak poloidal field region. A comparison of the 4–4.5 MW NBI-heated H-mode plasmas with radiative SF divertor and the standard radiative divertor (both induced with additional gas puffing) shows a nearly complete power detachment and broader divertor radiated power distribution in the SF, as compared to a partial detachment and peaked localized radiation in the standard divertor. However, insignificant difference in the detachment onset w.r.t. density between the SF and the standard divertor was found. The results complement the initial SF divertor studies conducted in high-power H-mode discharges in the NSTX and DIII-D tokamaks, and, along with snowflake divertor results from TCV and other tokamaks, contribute to the physics basis of the SF divertor as a power exhaust concept for future high power density tokamaks.

ELM-free and inter-ELM divertor heat flux broadening induced by edge harmonics oscillation in NSTX

A new n = 1 dominated edge harmonic oscillation (EHO) has been found in NSTX. The new EHO, rotating toroidally in the counter-current direction and the opposite direction of the neutral beam, was observed during certain inter-ELM and ELM-free periods of H-mode operation. This EHO is associated with a significant broadening of the integral heat flux width () by up to 150%, and a decrease in the divertor peak heat flux by >60%. An EHO induced filament was also observed by the gas puff imaging diagnostic. The toroidal rotating filaments could change the edge magnetic topology resulting in toroidal rotating strike point splitting and heat flux broadening. Experimental result of the counter current rotation of strike points splitting is consistent with the counter-current EHO.

Liquid lithium loop system to solve challenging technology issues for fusion power plant

Steady-state fusion power plant designs present major divertor technology challenges, including high divertor heat flux both in steady-state and during transients. In addition to these concerns, there are the unresolved technology issues of long term dust accumulation and associated tritium inventory and safety issues. It has been suggested that radiation-based liquid lithium (LL) divertor concepts with a modest lithium-loop could provide a possible solution for these outstanding fusion reactor technology issues, while potentially improving reactor plasma performance. The application of lithium (Li) in NSTX resulted in improved H-mode confinement, H-mode power threshold reduction, and reduction in the divertor peak heat flux while maintaining essentially Li-free core plasma operation even during H-modes. These promising results in NSTX and related modeling calculations motivated the radiative liquid lithium divertor concept and its variant, the active liquid lithium divertor concept, taking advantage of the enhanced or non-coronal Li radiation in relatively poorly confined divertor plasmas. To maintain the LL purity in a 1 GW-electric class fusion power plant, a closed LL loop system with a modest circulating capacity of ~1 l s−1 is envisioned. We examined two key technology issues: (1) dust or solid particle removal and (2) real time recovery of tritium from LL while keeping the tritium inventory level to an acceptable level. By running the LL-loop continuously, it can carry the dust particles and impurities generated in the vacuum vessel to the outside where the dust/impurities can be removed by relatively simple dust filter, cold trap and/or centrifugal separation systems. With ~1 l s−1 LL flow, even a small 0.1% dust content by weight (or 0.5 g s−1) suggests that the LL-loop could carry away nearly 16 tons of dust per year. In a 1 GW-electric (or ~3 GW fusion power) fusion power plant, about 0.5 g s−1 of tritium is needed to maintain the fusion fuel cycle assuming ~1% fusion burn efficiency. It appears feasible to recover tritium (T) in real time from LL while maintaining an acceptable T inventory level. Laboratory tests are being conducted to investigate T recovery feasibility with the surface cold trap concept.

Snowflake Divertor Experiments in the DIII-D, NSTX, and NSTX-U Tokamaks Aimed at the Development of the Divertor Power Exhaust Solution

Experimental results from the National Spherical Torus Experiment (NSTX), a medium-size spherical tokamak with a compact divertor, and DIII-D, a large conventional aspect ratio tokamak, demonstrate that the snowflake (SF) divertor configuration may provide a promising solution for mitigating divertor heat loads and target plate erosion compatible with core H-mode confinement in the future fusion devices, where the standard radiative divertor solution may be inadequate. In NSTX, where the initial high-power SF experiment was performed, the SF divertor was compatible with H-mode confinement, and led to the destabilization of large Edge Localized Modes (ELMs). However, a stable partial detachment of the outer strike point was also achieved where inter-ELM peak heat flux was reduced by factors 3–5, and peak ELM heat flux was reduced by up to 80% (see standard divertor). The DIII-D studies show the SF divertor enables significant power spreading in attached and radiative divertor conditions. Results include: compatibility with the core and pedestal, peak inter-ELM divertor heat flux reduction due to geometry at lower $n_{e}$ , and ELM energy and divertor peak heat flux reduction, especially prominent in radiative $D_{2}$ -seeded SF divertor, and nearly complete power detachment and broader radiated power distribution in the radiative $D_{2}$ -seeded SF divertor at $P_{\text {SOL}}=3-4$ MW. A variety of SF configurations can be supported by the divertor coil set in NSTX Upgrade. Edge transport modeling with the multifluid edge transport code UEDGE shows that the radiative SF divertor can successfully reduce peak divertor heat flux for the projected $P_{\text {SOL}} \simeq 9$ MW case. The radiative SF divertor with carbon impurity provides a wider $n_{e}$ operating window, 50% less argon is needed in the impurity-seeded SF configuration to achieve similar $q_{\text {peak}}$ reduction factors (see standard divertor).

Fusion nuclear science facilities and pilot plants based on the spherical tokamak

A fusion nuclear science facility (FNSF) could play an important role in the development of fusion energy by providing the nuclear environment needed to develop fusion materials and components. The spherical torus/tokamak (ST) is a leading candidate for an FNSF due to its potentially high neutron wall loading and modular configuration. A key consideration for the choice of FNSF configuration is the range of achievable missions as a function of device size. Possible missions include: providing high neutron wall loading and fluence, demonstrating tritium self-sufficiency, and demonstrating electrical self-sufficiency. All of these missions must also be compatible with a viable divertor, first-wall, and blanket solution. ST-FNSF configurations have been developed simultaneously incorporating for the first time: (1) a blanket system capable of tritium breeding ratio TBR ≈ 1, (2) a poloidal field coil set supporting high elongation and triangularity for a range of internal inductance and normalized beta values consistent with NSTX/NSTX-U previous/planned operation, (3) a long-legged divertor analogous to the MAST-U divertor which substantially reduces projected peak divertor heat-flux and has all outboard poloidal field coils outside the vacuum chamber and superconducting to reduce power consumption, and (4) a vertical maintenance scheme in which blanket structures and the centerstack can be removed independently. Progress in these ST-FNSF missions versus configuration studies including dependence on plasma major radius R0 for a range 1 m–2.2 m are described. In particular, it is found the threshold major radius for TBR = 1 is m, and a smaller R0 = 1 m ST device has TBR ≈ 0.9 which is below unity but substantially reduces T consumption relative to not breeding. Calculations of neutral beam heating and current drive for non-inductive ramp-up and sustainment are described. An A = 2, R0 = 3 m device incorporating high-temperature superconductor toroidal field coil magnets capable of high neutron fluence and both tritium and electrical self-sufficiency is also presented following systematic aspect ratio studies.

Liquid lithium applications for solving challenging fusion reactor issues and NSTX-U contributions

Steady-state fusion reactor operation presents major divertor technology challenges, including high divertor heat flux both steady-state and transients. In addition, there are unresolved issues of long term dust accumulation and associated tritium inventory and safety concerns (Federici et al., 2001) [1]. It has been suggested that radiative liquid lithium divertor concepts with a modest lithium-loop could provide a possible solution for these outstanding fusion reactor technology issues, while potentially improving reactor plasma performance (Ono et al., 2013, 2014) [2,3]. The application of lithium (Li) in NSTX resulted in improved H-mode confinement, H-mode power threshold reduction, and reduction in the divertor peak heat flux while maintaining essentially Li-free core plasma operation even during H-modes. These promising results in NSTX and related modeling calculations motivated the radiative liquid lithium (LL) divertor (RLLD) concept (Ono et al., 2013) [2] and its variant, the active liquid lithium divertor concept (ARLLD) (Ono et al., 2014) [3], taking advantage of the enhanced non-coronal Li radiation in relatively poorly confined divertor plasmas. It was estimated that only a few moles/s of lithium injection would be needed to significantly reduce the divertor heat flux in a tokamak fusion power plant. By operating at lower temperatures ≤450°C than the first wall ∼600–700°C, the LL-covered divertor chamber wall surfaces can serve as an effective particle pump, as impurities generally migrate toward lower temperature LL divertor surfaces. To maintain the LL purity, a closed LL loop system with a modest circulating capacity of ∼1l/s (l/s) is envisioned to sustain the steady-state operation of a 1GW-electric class fusion power plant. By running the Li loop continuously, it can carry the dust particles and impurities generated in the vacuum vessel to outside where the dust/impurities are removed by relatively simple filter and cold/hot trap systems. Using a cold trap system, it can recover tritium (T) in real time from LL at a rate of ∼0.5g/s needed to sustain the fusion reaction while minimizing the T inventory. With an expected T fraction of ≤0.7%, an acceptable T inventory level can be achieved. In NSTX-U (Menard et al., 2012; Ono et al., 2015) [4,5], preparations are now underway to elucidate the physics of Li plasma interactions with a number of Li application tools and Li radiation spectroscopic instruments. The NSTX-U Li evaporator, which provides Li coating over the lower divertor plate, can offer important information on the RLLD concept, and the Li granule injector will test some of the key physics issues for the ARLLD concept. A LL loop is also being prepared off-line for prototyping future use on NSTX-U.

Effect of resonant magnetic perturbations on low collisionality discharges in MAST and a comparison with ASDEX Upgrade

Sustained edge localized mode (ELM) mitigation has been achieved on MAST and AUG using resonant magnetic perturbations (RMPs) with various toroidal mode numbers over a wide range of low to medium collisionality discharges. The ELM energy loss and peak heat loads at the divertor targets have been reduced. The ELM mitigation phase is typically associated with a drop in plasma density and overall stored energy. In one particular scenario on MAST, by carefully adjusting the fuelling it has been possible to counteract the drop in density and to produce plasmas with mitigated ELMs, reduced peak divertor heat flux and with minimal degradation in pedestal height and confined energy. While the applied resonant magnetic perturbation field can be a good indicator for the onset of ELM mitigation on MAST and AUG there are some cases where this is not the case and which clearly emphasize the need to take into account the plasma response to the applied perturbations. The plasma response calculations show that the increase in ELM frequency is correlated with the size of the edge peeling-tearing like response of the plasma and the distortions of the plasma boundary in the X-point region. In many cases the RMPs act to increase the frequency of type I ELMs, however, there are examples where the type I ELMs are suppressed and there is a transition to a small or type IV ELM-ing regime.

The ARIES Advanced and Conservative Tokamak Power Plant Study

Tokamak power plants are studied with advanced and conservative design philosophies to identify the impacts on the resulting designs and to provide guidance to critical research needs. Incorporating updated physics understanding and using more sophisticated engineering and physics analysis, the tokamak configurations have developed a more credible basis compared with older studies. The advanced configuration assumes a self-cooled lead lithium blanket concept with SiC composite structural material with 58% thermal conversion efficiency. This plasma has a major radius of 6.25 m, a toroidal field of 6.0 T, a q95 of 4.5,a βtotalN of 5.75, an H98 of 1.65, an n/nGr of 1.0, and a peak divertor heat flux of 13.7 MW/m2. The conservative configuration assumes a dual-coolant lead lithium blanket concept with reduced-activation ferritic martensitic steel structural material and helium coolant, achieving a thermal conversion efficiency of 45%. The plasma has a major radius of 9.75 m, a toroidal field of 8.75 T, a q95 of 8.0, a βtotalN of 2.5, an H98 of 1.25, an n/nGr of 1.3, and a peak divertor heat flux of 10 MW/m2. The divertor heat flux treatment with a narrow power scrape-off width has driven the plasmas to larger major radius. Edge and divertor plasma simulations are targeting a basis for high radiated power fraction in the divertor, which is necessary for solutions to keep the peak heat flux in the range 10 to 15 MW/m2. Combinations of the advanced and conservative approaches show intermediate sizes. A new systems code using a database approach has been used and shows that the operating point is really an operating zone with some range of plasma and engineering parameters and very similar costs of electricity. Other papers in this issue provide more detailed discussion of the work summarized here.

Compatibility of detached divertor operation with robust edge pedestal performance

The compatibility of detached radiative divertor operation with a robust H-mode pedestal is examined in DIII-D. A density scan produced low temperature plasmas at the divertor target, Te⩽2eV, with high radiation leading to a factor of ⩾4 drop in peak divertor heat flux. The cold radiative plasma was confined to the divertor and did not extend across the separatrix in X-point region. A robust H-mode pedestal was maintained with a small degradation in pedestal pressure at the highest densities. The response of the pedestal pressure to increasing density is reproduced by the EPED pedestal model. However, agreement of the EPED model with experiment at high density requires an assumption of reduced diamagnetic stabilization of edge Peeling–Ballooning modes.

Application of the radiating divertor approach to innovative tokamak divertor concepts

We survey the results of recent DIII-D experiments that tested the effectiveness of three innovative tokamak divertor concepts in reducing divertor heat flux while still maintaining acceptable energy confinement under neon/deuterium-based radiating divertor (RD) conditions: (1) magnetically unbalanced high performance double-null divertor (DND) plasmas, (2) high performance double-null “Snowflake” (SF-DN) plasmas, and (3) single-null H-mode plasmas having different isolation from their divertor targets. In general, all three concepts adapt well to RD conditions, achieving significant reduction in divertor heat flux (q⊥p) and maintaining high performance metrics, e.g., 50–70% reduction in peak divertor heat flux for DND and SF-DN plasmas that are characterized by βN≅3.0 and H98(y,2)≈1.35. It is also demonstrated that q⊥p could be reduced ≈50% by extending the parallel connection length (L||-XPT) in the scrape-off layer between the X-point and divertor targets over a variety of the RD and non-RD environments tested.

Active control of divertor heat and particle fluxes in EAST towards advanced steady state operations

Significant progress has been made in EAST towards advanced steady state operations by active control of divertor heat and particle fluxes. Many innovative techniques have been developed to mitigate transient ELM and stationary heat fluxes on the divertor target plates. It has been found that lower hybrid current drive (LHCD) can lead to edge plasma ergodization, striation of the stationary heat flux and lower ELM transient heat and particle fluxes. With multi-pulse supersonic molecular beam injection (SMBI) to quantitatively regulate the divertor particle flux, the divertor power footprint pattern can be actively modified. H-modes have been extended over 30s in EAST with the divertor peak heat flux and the target temperature being controlled well below 2MW/m2 and 250°C, respectively, by integrating these new methods, coupled with advanced lithium wall conditioning and internal divertor pumping, along with an edge coherent mode to provide continuous particle and power exhaust.

Active radiative liquid lithium divertor concept

Developing a reactor compatible divertor has been identified as a particularly challenging technology problem for magnetic confinement fusion. Application of lithium (Li) in NSTX resulted in improved H-mode confinement, H-mode power threshold reduction, and reduction in the divertor peak heat flux while maintaining essentially Li-free core plasma operation even during H-modes. These promising Li results in NSTX and related modeling calculations motivated the radiative liquid lithium divertor (RLLD) concept [1]. In the RLLD, Li is evaporated from the liquid lithium (LL) coated divertor strike point surface due to the intense heat flux. The evaporated Li is readily ionized by the plasma due to its low ionization energy, and the poor Li particle confinement near the divertor plate enables ionized Li ions to radiate strongly, resulting in a significant reduction in the divertor heat flux. This radiative process has the desired effect of spreading the localized divertor heat load to the rest of the divertor chamber wall surfaces, facilitating divertor heat removal. The modeling results indicated that the Li radiation can be quite strong, so that only a small amount of Li (∼a few mol/s) is needed to significantly reduce the divertor peak heat flux for typical reactor parameters. In this paper, we examine an active version of the RLLD, which we term ARLLD, where LL is injected in the upstream region of divertor. We find that the ARLLD has similar effectiveness in reducing the divertor heat flux as the RLLD, again requiring only a few mol/s of LL to significantly reduce the divertor peak heat flux for a reactor. An advantage of the ARLLD is that one can inject LL proactively even in a feedback mode to insure the divertor peak heat flux remains below an acceptable level, providing the first line of defense against excessive divertor heat loads which could result in damage to divertor PFCs. Moreover, the low confinement property of the divertor (i.e., <1ms for Li particle confinement time) makes the ARLLD response fast enough to mitigate the effects of possible transient events such as large ELMs.

A Simple Hybrid Model for SOL, Pedestal and Core Tokamak Plasmas

AbstractIn this paper, the divertor heat flux density profile is being discussed. The simple robust model, dealing with core, pedestal and edge plasmas was improved. The model was applied to the ITER basic regime. Heat flux density was estimated for two different cases of heat flux SOL width of ITER. In the case of wide 2 cm SOL, the peak divertor heat flux density is under technological limit of 10 MW/m2. In the case of quite narrow 1 mm width SOL, peak divertor heat flux density exceeds this limit by several times and detached divertor regimes should be considered. (© 2014 WILEY‐VCH Verlag GmbH &amp; Co. KGaA, Weinheim)