Divertor Neutral Pressure Research Articles

Facilitated core-edge integration through divertor nitrogen seeding in the HL-2A tokamak

A divertor detachment with sustainable high-performance plasmas has been achieved through divertor nitrogen seeding in the HL-2A tokamak. The closed divertor structure facilitates achieving high divertor neutral pressure due to its efficient particle containment effect as demonstrated by both experimental and SOLPS simulation results, which aids in achieving the divertor detachment. The radiative divertor is conducive to high-frequency small edge localized modes (ELMs) operation, characterized by a reduced pedestal ion temperature gradient ∇Ti and the enhanced electron density gradient ∇ne . The presence of minority nitrogen at the edge plasma, which results from the divertor nitrogen seeding, contributes to the increase of ion temperature Ti in the confinement region by suppressing the turbulence through the impurity dilution effect and E×B shear. The increased ion temperature Ti and electron density ne compensate the energy loss resulting from the increased edge radiation during detachment, which contributes to the confinement sustainment combined with reduced pedestal energy loss caused by small ELMs. This work advances our understanding of the fundamental physics governing closed divertor detachment with sustainable high-performance plasmas through divertor nitrogen seeding.

Comparison of detachment in Ohmic plasmas with positive and negative triangularity

In recent years, negative triangularity (NT) has emerged as a potential high-confinement L-mode reactor solution. In this work, detachment is investigated using core density ramps in lower single null Ohmic L-mode plasmas across a wide range of upper, lower, and average triangularity (the mean of upper and lower triangularity: δ) in the TCV tokamak. It is universally found that detachment is more difficult to access for NT shaping. The outer divertor leg of discharges with δ≈−0.3 could not be cooled to below 5 eV through core density ramps alone. The behavior of the upstream plasma and geometrical divertor effects (e.g. a reduced connection length with negative lower triangularity) do not fully explain the challenges in detaching NT plasmas. Langmuir probe measurements of the target heat flux widths (λ q ) were constant to within 30% across an upper triangularity scan, while the spreading factor S was lower by up to 50% for NT, indicating a generally lower integral scrape-off layer width, λ int. The line-averaged core density was typically higher for NT discharges for a given fuelling rate, possibly linked to higher particle confinement in NT. Conversely, the divertor neutral pressure and integrated particle fluxes to the targets were typically lower for the same line-averaged density, indicating that NT configurations may be closer to the sheath-limited regime than their PT counterparts, which may explain why NT is more challenging to detach.

Comparison of reduced model predictions for divertor detachment onset and reattachment timescales in ASDEX Upgrade and JET experiments

Building on prior analysis of ASDEX Upgrade (AUG) experiments (Henderson et al 2023 Nucl. Fusion 63 086024), this study compares simple analytical formula predictions for divertor detachment onset and reattachment timescales in JET experiments. Detachment onset primarily scales with divertor neutral pressure, impurity concentration, power directed to the targets, machine size, and integral perpendicular power decay length. JET experiments, focusing on seeding mixtures of Ne and Ar, align with the detachment onset predictions. Radiation efficiencies among the impurities show good agreement with the model predictions, contrasting with AUG observations which suggested higher efficiency for Ar and lower efficiency for Ne. The time taken to re-ionise the neutral volume in front of the outer target in fully detached divertor conditions was measured following both abrupt increases in injected neutral beam power and, separately, cutting of the impurity gas flow. Re-ionisation of the neutrals occurs within approximately 1 s on JET, which aligns with the simple model prediction derived from AUG data. While the AUG results are not new, their comparison with the JET results enhances understanding, reinforcing confidence in using simple models to predict future reactor scenarios.

Impact of divertor neutral pressure on confinement degradation of advanced tokamak scenarios at ASDEX Upgrade

Over previous campaigns, an intense experimental program on advanced tokamak (AT) scenarios, has been carried out at the ASDEX Upgrade tokamak with full-tungsten wall. These discharges have been executed shortly after the boronization of the first wall to reduce the density and the impurity influx. The confinement level of such AT discharges was found to vary considerably, even when discharges with similar, if not identical, engineering parameters were carried out. This work investigates the causes of such confinement variations. Among all plasma quantities analyzed, confinement quality of AT scenarios correlates best with divertor neutral pressure, highlighting the key role of edge and scrape-off layer physics in determining global plasma confinement. In particular, it is found that the main cause of confinement degradation is the reduction of pedestal stability, which is in turn caused by the outward shift of the maximum density gradient position typically observed when the divertor neutral pressure increases. Owing to the low density of AT discharges under analysis, the movement of the maximum density gradient position can be caused entirely by changes in deuterium outgassing from the wall, which is strongly influenced by the boron layer deposited on the plasma-facing components and by the deuterium wall inventory. Finally, the predictive capability of confinement quality with the integrated model IMEP [Luda et al., Nucl. Fusion 60, 036023 (2020)] is tested on these discharges and shows promising results.

Deuterium recycling and wall retention characteristics during boron powder injection in EAST

Boron (B), as a low-Z material, is widely employed for wall conditioning to enhance plasma performance in fusion devices. In the Experimental Advanced Superconducting Tokamak, a series of experiments involving real-time B powder injection has been conducted to investigate fuel particle behavior. It was observed that fuel particle recycling decreased with an increase in the amount of B powder injected, resulting in an increase in short-term fuel retention. The fuel recycling decreased by up to 80%, as indicated by divertor neutral pressure and Dα line emission. Furthermore, each B atom exhibited a trapping capacity of 0.3 D particles during B powder injection at a typical flow rate. The real-time B injection had no wall hysteresis effect on D retention, implying that cumulative B injection and deposited film did not affect long-term D retention. The possible mechanism for D retention is the formation of B-C-O-D compounds and co-deposition between B and D particles during discharges. This investigation would be valuable for evaluating T retention when B is used as wall conditioning material in future fusion reactor devices.

Numerical study of divertor detachment in TCV H-mode scenarios

The effect of divertor closure and nitrogen seeding on the detachment process has been studied by performing 2D numerical simulations of tokamak à configuration variable (TCV) H-mode divertor scenarios with the SOLEDGE3X-EIRENE edge plasma transport code. The simulations reveal that, in the cases with only deuterium gas fuelling, detachment occurs at a similar level of divertor neutral pressure (0.76 Pa), despite the difference in divertor closure achieved by changing the length of the outer baffle. Nitrogen reduces the target temperature with little effect on the upstream density and momentum loss but drops the upstream pressure, leading to a decrease in the target particle flux and divertor neutral pressure. Furthermore, when the radiation front starts to move up from the outer target, the peak parallel heat flux level at the outer target remains approximately the same ( MW m−2), regardless of whether it is a deuterium fuelling scan, a nitrogen seeding scan at a fixed fuelling rate, or a change in the length of the outer baffle. An empirical partial detachment qualifier calibrated on AUG experimental data was compared with the TCV simulations. The results show good agreement in detachment state prediction, indicating the potential of this detachment qualifier to be applied in devices of different sizes, emphasizing the combined influence of input power entering the divertor, neutral pressure, and the concentration and species of impurity in achieving divertor detachment.

Measurement of divertor neutral pressure in EAST tokamak by ASDEX pressure gauge

In the tokamak plasma operation, divertor neutral particles play a key role in the study of fuel recycling, heat load mitigation, plasma confinement, and so on. Therefore, the in-situ measurement of neutral pressure in the divertor region is essential for the divertor physics studies. Two ASDEX pressure gauges were installed in the lower divertor dome region and passive plate region, respectively, for the in-situ pressure measurement. Experimental results show that, the ASDEX pressure gauge diagnostic is more sensitive, and its measurement on divertor neutral pressure is about 100 milliseconds faster than the external gauge of the divertor. Moreover, the ASDEX pressure gauge diagnostic is applicable for long pulse and high power plasma operation, and the in-situ pressure measurement of the divertor during over 200 s and higher than 10 MW discharges were successfully achieved in EAST. In addition, ASDEX pressure gauge diagnostic sensitively reacts to the changes in plasma parameters, and the neutral pressure is found to be significantly influenced by the plasma heating power. These results provide powerful technical support for the key divertor physical studies in EAST tokamak and the future fusion devices.

Investigation of helium exhaust dynamics at the ASDEX Upgrade tokamak with full-tungsten wall

An efficient removal of He ash by active pumping in future fusion devices is necessary to avoid fuel dilution and not degrade the core confinement properties. Therefore, a deep understanding of the underlying physics mechanisms is mandatory. Helium exhaust has been experimentally investigated at the ASDEX Upgrade tokamak. This is an ideal test environment, thanks to the ITER-like divertor geometry, an extensive diagnostics coverage and the presence of plasma-facing components made of tungsten. The exhaust efficiency, characterized by the He compression in the divertor, was found to improve with increasing divertor neutral pressure but to degrade with detachment. A multi-reservoir particle balance model was developed to interpret the observed exhaust dynamics, accounting for plasma transport and wall retention. The limited performance of the pumping system and the efficient helium retention capability of the tungsten wall were identified to have the strongest impact on the exhaust dynamics.

Power exhaust and core-divertor compatibility of the baffled snowflake divertor in TCV

A baffled snowflake minus low-field side (SF-LFS) is geometrically-optimised in tokamak à configuration variable, increasing divertor neutral pressure, to evaluate the roles of divertor closure (comparing with an unbaffled SF-LFS) and magnetic geometry (comparing with a baffled single null (SN)) in power exhaust and core-divertor compatibility. Ohmically-heated L-mode discharges in deuterium, with a line-averaged core density of approximately m−3, are seeded with nitrogen to approach detached conditions. Baffles in the SF-LFS configuration are found to reduce the peak outer target heat flux by up to , without significantly affecting the location of the inter-null radiation region or the core-divertor compatibility. When compared to the baffled SN, the baffled SF-LFS exhibits a reduction in the outer target heat flux by up to and the ability to balance the strike-point distribution of heat flux. These benefits are less significant with N2 seeding, with similar peak target quantities (such as heat flux, electron temperature and ion flux) and divertor radiated power. Despite a radiating region located farther from the confined plasma for the SF-LFS than the baffled SN, no change in core confinement is observed. Core effective charge even indicates an increase in core impurity penetration for the SF-LFS. These experiments constitute a good reference for detailed model validations and extrapolations, exploring important physics such as core impurity shielding and the dependence of divertor cross-field transport on magnetic geometry.

The effect of impurity seeding into the closed divertor on plasma detachment in the HL-2A tokamak

Recent progress towards an increased understanding of detached divertor physics has been made with the highly closed divertor geometry in HL-2A. Non-intrinsic impurities were injected into the outer divertor chamber, and increased divertor neutral pressure and enhanced volumetric energy loss in the divertor were observed. Meanwhile the neutral pressure in the main chamber decreased slightly, and neutral compression between the divertor and main chamber increased greatly. This led to divertor detachment with a low upstream plasma line-averaged electron density (). In the H-mode, slight degradation of the core confinement, characterized by a decrease in plasma stored energy and pedestal pressure and an increase in edge-localized mode frequency, was observed, but the H-mode was still sustained well with H98 > 1. Pedestal density fluctuation was increased during detachment, implying that the enhanced pedestal transport might be responsible for the degradation. During the divertor detachment phase, the impurities were well controlled in the divertor without strong radiation near the X-point region, and the main plasma density did not increase but decreased slightly; this could be a benefit of the highly closed divertor geometry. The experimental results suggest that a closed divertor geometry has the advantages of volumetric energy loss, gas pumping and impurity control in the divertor without significant effects on the plasma confinement, thus giving a wider operating window for divertor detachment.

Simulation of Liquid Lithium Divertor Geometry Using SOLPS-ITER

Plasma-facing component (PFC) geometries are evaluated for a Fusion Nuclear Science Facility (FNSF) design to find solutions that are compatible with flowing liquid lithium components while satisfying requirements from the perspective of plasma and neutral particle transport. Flowing liquid metal (LM) divertor systems offer important advantages due to continual regeneration of the surface material, but may require modifications from standard optimized tokamak divertor designs. Scrape Off Layer Plasma Simulator for the International Thermonuclear Experimental Reactor (SOLPS-ITER) simulations are used to compare standard vertical target, open, and balanced baffled geometries. It is found that the open geometry offers little control of neutral particles and has narrow operating windows where the divertor fluxes can be lowered to acceptable levels, while maintaining the required upstream density. The addition of neutral baffles allows greater control over the divertor conditions with less impact on the upstream density. The divertor neutral pressure in the baffled geometry is slightly higher than the open divertor, but not as large with a vertical target. A first-pass coupling of the SOLPS solution with sheath and implantation/erosion models to compute the lithium emission shows that the lithium is largely confined to the near-surface region due to the small ionization mean free path and large main ion flow toward the surface. The lithium source was varied by three orders of magnitude. At the highest rate, when the sourced lithium approaches the level of the main ion recycling flux, a high core lithium concentration (~10%) is observed with only moderate power dissipation to affect the divertor plasma.

High gas throughput SOLPS-ITER simulations extending the ITER database to strong detachment

SOLPS-ITER simulations performed for Q DT = 10, P SOL = 100 MW burning plasmas on ITER extend the existing database to high values of separatrix averaged neon impurity concentration (⟨c Ne⟩ ≈ 6%) and divertor neutral pressure (⟨p div⟩ > 25 Pa) in order to determine the heat flux mitigation capability of these scenarios and whether strongly detached states are accessible. In the existing database of ITER simulations, the level of detachment was limited to cases where the integral ion flux to the outer target was greater than 80% of the value at rollover, with the impurity radiation localized near the target. With the possibility of narrow heat flux channels and increased deposited power due to tile shaping, it is important to explore operation at a higher degree of detachment. Two series of simulations were explored to extend the database of SOLPS simulations. By increasing the deuterium and neon puff rates proportionally, the peak divertor energy flux (q ⊥,max) is decreased from 5 to 3 MW m−2 while ⟨p div⟩ increased from 11 to 27 Pa. By increasing only the neon puff, q ⊥, max can be reduced to <1MW m−2 while ⟨p div⟩ is maintained at Pa. As the neon puff level is increased, the position of the impurity radiation peak is shifted towards the X-point. At the highest neon puff levels with steady-state solutions, the electron temperature is reduced below 1 eV across 50 cm of each divertor target. The new cases extend previously observed tight relationships in power and momentum loss factors to low electron temperature improving their utility for highly detached regimes.

New insights on divertor parallel flows,E × B drifts, and fluctuations from in situ, two-dimensional probe measurement in the Tokamak à Configuration Variable

In situ, two-dimensional (2D) Langmuir probe measurements across a large part of the TCV outer divertor are reported in L-mode discharges with and without divertor baffles. This provides detailed insights into time averaged profiles, particle fluxes, and fluctuation behavior in different divertor regimes. The presence of the baffles is shown to substantially increase the divertor neutral pressure for a given upstream density and to facilitate the access to detachment, an effect that increases with plasma current. The detailed, 2D probe measurements allow for a divertor particle balance, including ion flux contributions from parallel flows and E × B drifts. The poloidal flux contribution from the latter is often comparable or even larger than the former, and the divertor parallel flow direction reverses in some conditions, pointing away from the target. In most conditions, the integrated particle flux at the outer target can be predominantly ascribed to ionization along the outer divertor leg, consistent with a closed-box approximation of the divertor. The exception is a strongly detached divertor, achieved here only with baffles, where the total poloidal ion flux even decreases towards the outer target, indicative of significant plasma recombination. The most striking observation from relative density fluctuation measurements along the outer divertor leg is the transition from poloidally uniform fluctuation levels in attached conditions to fluctuations strongly peaking near the X-point when approaching detachment.

Dependence of scrape-off layer profiles and turbulence on gas fuelling in high density H-mode regimes in TCV

A set of high density, highly shaped H-mode discharges has been performed in the TCV tokamak with the aim of assessing the effects of increasing divertor neutral recycling on the properties of upstream inter-ELM scrape-off layer (SOL) profiles and transport. An increase of divertor neutral pressure has been correlated with the evolution of separatrix properties and turbulence level. The latter has been quantified by means of the α t parameter introduced in (Eich 2020 Nucl. Fusion 60 056016), describing the contribution of resistive-interchange turbulence in the SOL relative to drift wave transport. The analysis reveals a general broadening of the upstream SOL profiles as α t increases, with the SOL power width measured by the vertical IR thermography system increasing significantly. In a similar way, the upstream density profile widens in the near SOL, whereas in the far SOL a density shoulder is observed to progressively form and increase in amplitude. This behaviour is associated with an enhancement of far SOL turbulent transport in the form of blob-filaments travelling radially faster across the far SOL and becoming bigger at higher α t. The detected filaments, evaluated from the fast reciprocating probe at the outer midplane, are determined to mostly belong to the resistive ballooning and resistive X-point regimes.

Experimental study on the role of the target electron temperature as a key parameter linking recycling to plasma performance in JET-ILW* *This manuscript has been authored by UT-Battelle, LLC, under contract DE-AC05-00OR22725 with the US Department of Energy (DOE). The US government retains and the publisher, by accepting the article for publication, acknowledges that the US government retains a nonexclusive,

Changes in global and edge plasma parameters (H 98(y,2), dimensionless collisionality ν *, core density peaking, separatrix density n e,sep) with variations in the D2 fueling rate and divertor configuration are unified into a single trend when mapped to ⟨T e,ot⟩, the spatially averaged spectroscopically derived outer target electron temperature. Dedicated JET with the ITER-like wall (JET-ILW) experiments in combination with an extended JET-ILW database of unseeded low-triangularity H-mode plasmas spanning a wide range of D2 fueling rates, I p, B t and heating power have demonstrated the importance of ⟨T e,ot⟩ as a key physics parameter linking the recycling particle source and detachment with plasma performance. The remarkably robust H 98(y,2) trend with ⟨T e,ot⟩ is connected to a strong inverse correlation between ⟨T e,ot⟩, n e,sep and ν *, thus directly linking changes in the divertor recycling moderated by ⟨T e,ot⟩ with the previously established relationship between ν *, core density peaking and core pressure resulting in a degradation in core plasma performance with decreasing ⟨T e,ot⟩ (increasing ν *). A strong inverse correlation between the separatrix to pedestal density ratio, n e,sep/n e,ped, and ⟨T e,ot⟩ is also established, with the rise in n e,sep/n e,ped saturating at ⟨T e,ot⟩ > 10 eV. A strong reduction in H 98(y,2) is observed as ⟨T e,ot⟩ is driven from 30 to 10 eV via additional D2 gas fueling, while the divertor remains attached. Consequently, the pronounced performance degradation in attached divertor conditions has implications for impurity seeding radiative divertor scenarios, in which H 98(y,2) is already low (∼0.7) before impurities are injected into the plasma since moderate gas fueling rates are required to promote high divertor neutral pressure. A favorable pedestal pressure, p e,ped, dependence on I p has also been observed, with an overall increase in p e,ped at I p = 3.4 MA as ⟨T e,ot⟩ is driven down from attached to high-recycling divertor conditions. In contrast, p e,ped is reduced with decreasing ⟨T e,ot⟩ in the lower I p branches. Further work is needed to (i) clarify the potential role of edge opacity on the observed favorable pedestal pressure I p scaling; as well as to (ii) project the global and edge plasma performance trends with ⟨T e,ot⟩ to reactor-scale devices to improve predictive capability of the coupling between recycling and confined plasma fueling in what are foreseen to be more opaque edge plasma conditions.

Fuel retention in WEST and ITER divertors based on FESTIM monoblock simulations

The influence of the input power (IP), puffing rate and neutral pressure on the fuel (hydrogen isotopes) inventory of the WEST and ITER divertors is investigated. For the chosen range of parameters (relatively low temperature at the strike points), the inventory of the WEST divertor evolves as the power 0.2 of the puffing rate and as the power 0.3 of the IP. The inventory at the strike points is highly dominated by ions whereas it is dominated by neutrals in the private zone. Increasing the fuelling rate increases the retention in the private zone and decreases slightly the retention at the strike points. Increasing the IP increases the inventory at the strike points and does not affect much the inventory at the private flux region. The inventory of the ITER divertor is not strongly dependent on the divertor neutral pressure. The inventory increases from 0 Pa to 7 Pa and then decreases slightly from 7 Pa to 10 Pa. After 107 s of continuous exposure, the maximum inventory in the ITER divertor was found to be 14 g. The inventory is not maximum at the strike points due to the high surface temperature of the monoblocks in this region. The maximum accumulation of H in the ITER divertor is below 5 mg per 400 s discharge and below 2 mg per 400 s discharge after 200 discharges.

SOLPS-ITER validation with TCV L-mode discharges

This work presents a quantitative test of SOLPS-ITER simulations against tokamak à configuration variable (TCV) L-mode experiments. These simulations account for drifts, currents, kinetic neutrals, and carbon impurities providing the most complete edge transport simulations for TCV to date. The comparison is performed on nominally identical discharges carried out to assess the effectiveness of TCV's divertor baffles in the framework of the European Plasma Exhaust program and employs numerous edge diagnostics providing a detailed code-experiment benchmark for TCV. The simulations show a qualitative consistency, but the quantitative differences remain, which are assessed herein. It is found that, for a given separatrix density, the simulations most notably yield a colder, and denser, divertor state with a higher divertor neutral pressure than measured.

Understanding detachment of the W7-X island divertor

The fundamental behavior of the W7-X island divertor under detached conditions, which has been theoretically predicted with the EMC3-Eirene code, is re-examined here under the experimental conditions achieved so far and compared with the first experimental results. Both simulations and experiments cover a range of divertor configurations and plasma parameters, and show the following common trends: (1) with rising impurity radiation, the target heat load decreases ‘uniformly’ over the entire target surface in the sense that both the peak and average heat loads can drop by an order of magnitude. Impurity radiation (mainly from intrinsic carbon) occurs primarily at the plasma edge and the resulting negative impact on the stored energy is less than 10%. (2) When the total radiation exceeds a critical level, the target particle flux (the recycling flux Γrecy) begins to fall and can drop by a factor of 3–5 at high radiation levels without an obvious indication of significant volume recombination. (3) While Γrecy decreases, the divertor neutral pressure continues to build up and reaches a maximum, at which point Γrecy has declined significantly. (4) During detachment, the electron temperature at the last closed flux surface falls in a way that is not quantitatively understandable from parallel classical heat conduction processes. This paper presents a physical explanation of the numerical/experimental results described above. Furthermore, using the EMC3-Eirene code as a diagnostic tool, we are able, apparently for the first time, to provide a full quantitative analysis of each transport channel in the island divertor, aiming to clarify how the island divertor plasma self-regulates to maintain particle, energy, and momentum balance under detached conditions.

Dependence of upstream SOL density shoulder on divertor neutral pressure observed in L-mode and H-mode plasmas in the EAST superconducting tokamak

Upstream density profiles in the scrape-off layer (SOL) have been examined in low-confinement mode (L-mode) and high-confinement mode (H-mode) plasmas in the EAST superconducting tokamak. A weak density shoulder forms in the near SOL region in upper single-null configurations when the neutral pressure measured at the lower divertor exceeds a threshold value of 2 × 10−2 Pa in L-mode plasmas. When the neutral pressure is below this threshold, the weak density shoulder is absent and the sidebands of the lower hybrid waves associated with SOL parametric instabilities are reduced. Active detachment control with neon–deuterium seeding demonstrate that the weak density shoulder can form before the onset of the outer divertor detachment as long as the neutral pressure is above the threshold. Furthermore, no remarkable expansion of a shoulder is observed during divertor detachment, suggesting that divertor detachment is not a necessary condition for the formation or growth of a density shoulder. Through the increase in neutral pressure in the lower divertor by an order of magnitude, the weak shoulder was observed to expand into the far SOL and reach the leading edge of the limiter. The results in L-mode discharges identified the neutral pressure in the lower divertor as a primary factor for the formation of an SOL density shoulder in the upper single-null discharges. For the type-I ELMy H-mode plasmas, a similar density shoulder was detected during the inter-ELM phase when the neutral pressure in the lower divertor exceeded a threshold value of 4 × 10−2 Pa. On the other hand, the shoulder was absent when the divertor neutral pressure went below this threshold even though the plasma discharge was conducted with a higher core line-averaged density and divertor collisionality. This is consistent with the observations in L-mode plasmas. The neutral particle ionization of the working gas is thus believed to play a key role during the formation of the SOL density shoulder in the EAST tokamak.

Divertor closure effects on the TCV boundary plasma

The Tokamak à Configuration Variable (TCV) has recently been equipped with gas baffles to increase its divertor closure for a broad range of divertor magnetic geometries. First experimental results reported in Reimerdes et al. (2021) demonstrated compatibility with a broad range of divertor magnetic geometries and confirmed the main design constraints of the baffles, in particular an increased divertor neutral pressure. The present article presents a more in-depths analysis and extended experiments of this first baffle assessment on the TCV boundary plasma. It is shown that the divertor neutral pressure increased following the installation of the baffles, as predicted by SOLPS-ITER and SolEdge2D-EIRENE simulations. Varying the divertor closure by changing the position of the plasma showed that the plasma equilibrium designed to assess the baffle effect was not far from the optimal trade-off between plasma plugging and recycling on the baffles. The baffles facilitate access to a partially detached regime in both L- and H-modes. In L-Mode, with the ion ∇B-drift directed from the X-Point to the plasma core, a reduction of the line-averaged density detachment threshold by approximately 20% is observed at the outer target, while inner strike point detachment is only achieved in the presence of baffles. Multispectral imaging shows that the CIII front moves from the outer target towards the X-Point at a lower line-averaged plasma density, indicating a colder outer leg. In H-mode, the CIII front is generally located near the X-Point between the ELMs, while without baffles, N2-seeding is required to move the front up to that location.