Divergence Angle Research Articles

Multi-hole grid thruster plume simulation model based on single grid aperture analytical model

This paper presents a plume divergence angle prediction model for ion thruster. Firstly, an analytical model using Gaussian distribution for single grid hole plume is proposed. The parameters of this single hole model are obtained from the particle simulation results of ion optics which utilizes the immersed finite element Particle-in-cell Monte Carlo collision (IFE-PIC-MCC) method. Then, by the extension of the single hole model, a three-dimensional plume model for the whole ion optics is proposed. This plume model can be used to predict the divergence angle of ion thruster plume. Finally, a numerical example with the simulation of a 217-hole ion optics is provided to demonstrate the features of the proposed method.

Numerical Analysis of Convergent-Divergent Angles and Operating Conditions Impact on Rocket Nozzle Performance Parameters

Comprehensive numerical analysis was conducted to elucidate the exhaust performance of rocket engine nozzles. The study focused on unravelling the intricate relationship between convergence and divergence angles and their impact on the exhaust performance parameters, including velocity coefficient (cv), angularity coefficient (Ca), and gross thrust coefficient (Cfg). In contrast to conventional studies that focus mainly on the divergent section, this research delved into both convergent and divergent aspects of nozzle geometry. For the convergent section, a range of angles from 20° to 45° was systematically examined. For the divergent section, a wide spectrum of angles was explored, ranging from small (10°-13°), medium (14°-19°) and large (20°-25°) divergent angles. Further, we venture beyond geometry, investigating the influence of nozzle pressure ratio (NPR) on these key metrics. Realisable 𝑘𝑘−𝜀𝜀, enhanced wall traitement was used to simulate nozzle flow. The study identified the optimal convergent angle at 37.5°. The 15° diverging angle provides good overall performance, while the 23° angle strikes the ideal compromise: maximizing thrust and efficiency while minimizing weight and maintaining optimal performance.

Effect of pulse frequency on discharge characteristics of Hall thruster under pulsating operation

In this study, the effect of pulse frequency on the discharge and plume characteristics of Hall thrusters under pulsating operation is investigated. The experimental results show that the discharge current and thrust decrease as the frequency increases to the range of 30–90 kHz. The efficiency of the thruster is negatively correlated with the pulse frequency, and the pulse frequency minimally affects the plume divergence angle and ion current. It is found that an increase in the pulse frequency decreases the secondary electron emission flux on the wall and the near-wall conduction rate of electrons in the channel, thus consequently decreasing the electron current. An increase in the electron current share improves the current-utilization efficiency. In addition, as the frequency increases, the ion power loss on wall increases and the ion acceleration becomes less effective, thus resulting in a decrease in thrust. The combined effect of these two factors results in an increase in the anode efficiency as the frequency increases.

Smooth motion parallax method for 3D light-field displays with a narrow pitch based on optimizing the light beam divergence angle.

The three-dimensional (3D) light field display (LFD) with dense views can provide smooth motion parallax for the human eye. Increasing the number of views will widen the lens pitch, however, resulting in a decrease in view resolution. In this paper, an approach to smooth motion parallax based on optimizing the divergence angle of the light beam (DALB) for 3D LFD with narrow pitch is proposed. DALB is controlled by lens design. A views-fitting optimization algorithm is established based on a mathematical model between DALB and view distribution. Subsequently, the lens is reversely designed based on the optimization results. A co-designed convolutional neural network (CNN) is used to implement the algorithm. The optical experiment shows that a smooth motion parallax 3D image is achievable through the proposed method.

“Turbulence effect on total mechanical energy budget and energy loss of turbulent flows with different hydraulic regimes in open-channel transitions”

ABSTRACT Transitions are needed in hydraulic structures which are flumed. In expanding transitions, flow separates from the boundary if the angle of divergence exceeds about 5 degrees. The present paper gives an insight into the turbulence effect and energy loss in expanding transition with small angle of divergence. In wide angle expansion, flow separates from the boundary resulting in highly non-uniform velocity distribution at the exit of expansion resulting in erosion of down stream channel. Author performed experiments to control separation of flow in wide angle expansion. The paper discusses about the devices used by the author to control separation in wide angle expanding transition.

Experimental realization of near-critical-density laser wakefield acceleration: Efficient pointing 100-keV-class electron beam generation by microcapillary targets

We experimentally demonstrated the generation of a pointing stable, low-divergence, low-energy electron beam driven by near-critical-density laser wakefield acceleration using a moderate low-intensity laser pulse. Electron beams with a half-beam divergence angle of ∼30 mrad were generated at laser intensities of 4 × 1016–1 × 1018 W/cm2 from a microcapillary hole. The pointing fluctuation of the electron beam was 1.8 mrad (root-mean-square) at the maximum laser intensity of 1 × 1018 W/cm2. The energies of the electron beam were up to 400 keV at 1 × 1018 W/cm2 and 50 keV even at 1 × 1016 W/cm2. We confirmed that the peak energy of the hump or cutoff energy of the electron beams was reproduced in particle-in-cell simulation. Such low divergence electron beam generation at sub-relativistic intensity (1016 to 1017 W/cm2 order) will lead to various applications of laser-driven keV-class electron beams, such as advanced radiotherapy.

Experimental and numerical study on wet steam flow metering overreading characteristics in venturi tube

The precise measurement of wet-steam flow is of great importance in various industrial systems, including nuclear reactors, oil and gas transportation, and cogeneration systems. However, the measurement accuracy of wet-steam flow can be affected by overreading (OR) when using venturi meters. This paper presents a systematic numerical simulation using the DPM model and an experimental study on the characteristics of overreading in wet-steam flow metering. The experiments are carried out on a two-phase flow liquid and steam platform. Firstly, the OR characteristics of a venturi structure with fixed dimensions (a throttling ratio of 0.6, a divergence angle of 15°, and a venturi diameter of 20 mm) are quantitatively analyzed at different flow rates (0.14-0.32 kg/s) and qualities (ranging from 0.14 to 0.90). It is found that the Lockhart-Martinelli parameter (XLM) plays a more significant role than the gas Froude number (Frg) in determining the overreading (OR) characteristics of a venturi under a given temperature, pressure, and venturi structure. Secondly, a venturi overreading prediction model based on XLM is proposed, and its ability to predict overreading for larger mass flow rates and venturi diameters is verified by numerical simulation data. As evaluated through numerical simulation data, the proposed model’s maximum relative error and average deviation are below 15% and 10%, respectively. This study provides valuable insights into developing an overreading model for industrial applications under large flow and venturi diameter conditions.

Acoustics and aerodynamic effects following glottal and infraglottal medialization in an excised larynx model

ObjectiveThis study aimed to investigate the impact of the implant’s vertical location during Type 1 Thyroplasty (T1T) on acoustics and glottal aerodynamics using excised canine larynx model, providing insights into the optimal technique for treating unilateral vocal fold paralysis (UVFP).MethodsMeasurements were conducted in six excised canine larynges using Silastic implants. Two implant locations, glottal and infraglottal, were tested for each larynx at low and high subglottal pressure levels. Acoustic and intraglottal flow velocity field measurements were taken to assess vocal efficiency (VE), cepstral peak prominence (CPP), and the development of intraglottal vortices.ResultsThe results indicated that the implant's vertical location significantly influenced vocal efficiency (p = 0.045), with the infraglottal implant generally yielding higher VE values. The effect on CPP was not statistically significant (p = 0.234). Intraglottal velocity field measurements demonstrated larger glottal divergence angles and stronger vortices with the infraglottal implant.ConclusionThe findings suggest that medializing the paralyzed fold at the infraglottal level rather than the glottal level can lead to improved vocal efficiency. The observed larger divergence angles and stronger intraglottal vortices with infraglottal medialization may enhance voice outcomes in UVFP patients. These findings have important implications for optimizing T1T procedures and improving voice quality in individuals with UVFP. Further research is warranted to validate these results in clinical settings.

Divergence angle consideration in energy spread measurement for high-quality relativistic electron beam in laser wakefield acceleration

The thorough exploration of the transverse quality represented by divergence angle has been lacking yet in the energy spread measurement of the relativistic electron beam for laser wakefield acceleration (LWFA). In this work, we fill this gap by numerical simulations based on the experimental data, which indicate that in a C-shape magnet, magnetic field possesses the beam focusing effect, considering that the divergence angle will result in an increase in the full width at half maxima (FWHM) of the electron density distribution in a uniformly isotropic manner, while the length-to-width ratio decreases. This indicates that the energy spread obtained from the electron deflection distance is smaller than the actual value, regardless of the divergence angle. A promising and efficient way to accurately correct the value is presented by considering the divergence angle (for instance, for an electron beam with a length-to-width ratio of 1.12, the energy spread correct from 1.2% to 1.5%), providing a reference for developing the high-quality electron beam source.

Performance analysis of high-spectral-resolution lidar with/without laser seeding technique for measuring aerosol optical properties

High-spectral-resolution lidar (HSRL) is a powerful tool for aerosol measurements. With/without laser seeding technique in the transmitted laser, the HSRL can be distinguished as the single-longitudinal-mode (SLM) HSRL or the multi-longitudinal-mode (MLM) HSRL, and the Mach-Zehnder interferometer (MZI) with periodic transmittance function can be used as the spectral discriminator in both the SLM HSRL and MLM HSRL. To in-depth knowledge of the respective advantages of the SLM HSRL and MLM HSRL for measuring aerosol optical properties, the working principle, optimal parameter setting, and detection performance of the SLM HSRL and MLM HSRL are analyzed and discussed in detail, respectively. The working principle of the SLM HSRL and MLM HSRL indicate that the effective transmittance of MZI is the important parameter of data retrieval, the main source of retrieval uncertainties, and the key factor of MZI optical path difference (OPD) settings. To ensure that the MZI can achieve the preferable separation for aerosol Mie scattering signals and molecular Rayleigh scattering signals, the optimal OPDs of MZI are set at 165 mm and 1000 mm in the SLM HSRL and MLM HSRL from the aspects of the effective transmittance of MZI and the spectral discrimination ratio (SDR). Besides, to analyze the influence of frequency difference and divergence angle for the detection performance of HSRL, the effective transmittance of MZI and SDR are simulated and the results show that the MLM HSRL has higher requirements for the environmental parameters and the echo beam collimation than the SLM HSRL. Moreover, the HSRLs with SLM and MLM transmitted lasers are constructed in Xi'an for measuring aerosol optical properties. The preliminary measurement results show that the range square corrected signal (RSCS) of Rayleigh channel is smaller than that of Mie channel in both the SLM HSRL and MLM HSRL, while the difference between RSCS of Rayleigh channel and RSCS of Mie channel in the SLM HSRL is larger than that in the MLM HSRL, and the detection range of the SLM HSRL is lower than that of the MLM HSRL.

High-Power Mid-Infrared Quantum Cascade Laser with Large Emitter Width

High-power quantum cascade lasers (QCLs) have a wide application prospect. In this paper, a high-power high-beam-quality device with a large ridge width is demonstrated. The effect of different ridge widths on mode loss was studied, and the results showed that the mode loss decreased as the ridge width increased. Furthermore, as the width of the ridge increased, the temperature of the active region rose. In the experiment, the wafers were grown by metal–organic chemical vapor deposition (MOCVD), and the ridge width of the device was controlled by wet etching. A laser with a ridge width of 15 µm and a length of 5 mm achieved an output of 2.2 W under 288 K continuous wave (CW) operation, with a maximum slow-axis divergence angle of 27.2° and a device wavelength of 5 μm. The research results of this article promote the industrial production of base transverse mode QCL.

Theoretical and experimental studies on channel impulse response of short-range non-line-of-sight ultraviolet communications.

A theoretical channel impulse response (CIR) model of short-range non-line-of-sight (NLOS) ultraviolet communications (UVC) in noncoplanar geometry under the single-scatter condition is proposed. Simulation results obtained from the widely accepted Monte-Carlo (MC)-based channel model of NLOS UVC are provided to verify corresponding theoretical results obtained from the proposed theoretical single-scatter CIR model. Additionally, an outdoor experiment with a light-emitting diode (LED) as the light source is first designed to measure the channel step response of NLOS UVC and to further validate the proposed theoretical single-scatter CIR model. By varying the different parameters of the transmitter and the receiver, such as the baseline range, the inclination angle, the azimuth angle, the beam divergence angle, and the field-of-view angle, the results of the proposed theoretical single-scatter CIR model and the MC-based channel model are exhibited and further analyzed in detail. Results indicate that the computational time cost by the proposed theoretical single-scatter CIR model is decreased to less than 0.6% of the MC-based one with comparable accuracy in assessing the temporal characteristics of NLOS UVC channels. Additionally, theoretical results obtained from the proposed theoretical single-scatter CIR model manifest satisfactory agreement with corresponding experimental measurements.

High-beam-quality low-resistance vertical-cavity surface-emitting laser array with graphene electrode.

Thermal crosstalk and current crowding effects are pressing issues that significantly impact the beam quality and efficiency of vertical-cavity surface-emitting laser (VCSEL) arrays. In this paper, by taking advantage of the excellent current transmission characteristics of graphene, what we believe to be a novel VCSEL array based on graphene electrode is designed to realize vertical current injections. The series resistance and self-heating of arrays are reduced by controlling the transport direction of the current, effectively suppressing the thermal crosstalk effect. Furthermore, high array beam quality is obtained by optimizing the current density distribution in active regions. Ultimately, the high-power quasi-single mode emission of VCSEL arrays is achieved by introducing graphene electrodes (Gr-VCSEL array) designs. Compared to traditional VCSEL arrays, the 10 × 10 Gr-VCSEL array demonstrates a 41% reduction in series resistance, a side mode suppression ratio of 32 dB, and a divergence angle around 12 °. This structure simultaneously achieves quasi-single mode emission and effectively suppresses the thermal crosstalk effect, providing a new method for the development of high-beam quality VCSEL arrays.

Research on the Drift Prediction of Marine Floating Debris: A Case Study of the South China Sea Maritime Drift Experiment

Annually, hundreds of individuals tragically lose their lives at sea due to shipwrecks or aircraft accidents. For search and rescue personnel, the task of locating the debris of a downed aircraft in the vastness of the ocean presents a formidable challenge. A primary task these teams face is determining the search area, which is a critical step in the rescue operation. The movement of aircraft wreckage on the ocean surface is extremely complex, influenced by the combined effects of surface winds, waves, and currents. Establishing an appropriate drift motion prediction model is instrumental in accurately determining the search area for the wreckage. This article initially conducts maritime drift observation experiments on wreckage, and based on the results of these experiments, analyzes the drift characteristics and patterns of the debris. Subsequently, employing a wealth of observational experimental data, three types of drift prediction models for the wreckage are established using the least squares method. These models include the AP98 model, the dynamics model, and an improved model. In conclusion, the effectiveness and accuracy of the three models is evaluated and analyzed using Monte Carlo techniques. The results indicate that the probability of positive crosswind leeway (CWL) is 47.4%, while the probability of negative crosswind leeway (CWL) is 52.6%. The jibing frequency is 7.7% per hour, and the maximum leeway divergence angle observed is 40.4 degrees. Among the three drift prediction models, the refined AP98 drift model demonstrates the highest forecasting precision. The findings of this study offer a more accurate drift prediction model for the search of an aircraft lost at sea. These results hold significant guiding importance for maritime search and rescue operations in the South China Sea.

Optical–Mechanical Integration Analysis and Validation of LiDAR Integrated Systems with a Small Field of View and High Repetition Frequency

Integrated systems are facing complex and changing environments with the wide application of atmospheric LiDAR in civil, aerospace, and military fields. Traditional analysis methods employ optical software to evaluate the optical performance of integrated systems, and cannot comprehensively consider the influence of optical and mechanical coupling on the optical performance of the integrated system, resulting in the unsatisfactory accuracy of the analysis results. Optical–mechanical integration technology provides a promising solution to this problem. A small-field-of-view LiDAR system with high repetition frequency, low energy, and single-photon detection technology was taken as an example in this study, and the Zernike polynomial fitting algorithm was programmed to enable transmission between optical and mechanical data. Optical–mechanical integration technology was employed to obtain the optical parameters of the integrated system under a gravity load in the process of designing the optical–mechanical structure of the integrated system. The experimental validation results revealed that the optical–mechanical integration analysis of the divergence angle of the transmission unit resulted in an error of 2.586%. The focal length of the telescope increased by 89 μm, its field of view was 244 μrad, and the error of the detector target surface spot was 4.196%. The continuous day/night detection results showed that the system could accurately detect the temporal and spatial variations in clouds and aerosols. The inverted optical depths were experimentally compared with those obtained using a solar photometer. The average optical depth was 0.314, as detected using LiDAR, and 0.329, as detected by the sun photometer, with an average detection error of 4.559%. Therefore, optical–mechanical integration analysis can effectively improve the stability of the structure of highly integrated and complex optical systems.

Presenting new artificial intelligence techniques for finding optimum performance of solar chimney power plant

The various applications of solar energy have progressed significantly over recent decades. In this paper, finding the optimum performance criteria of a SCPP is studied. The mathematical modelling of 1-D flow is written and the optimum performance is determined for each group of geometric and environmental variables including the angle of collector roof (β), chimney divergence (α) and ambient wind velocity (Va ). In addition, different artificial intelligence techniques including regression tree, genetic programming and a novel method named trended regression tree are applied to find optimum performance conditions at any arbitrary group of α, β and Va . Results indicate that maximum power output (Pt ) and associated mass flow rate ( m ˙ ) increase with increasing chimney divergent angle and wind velocity at a constant collector roof angle. Comparing the obtained results of artificial intelligence techniques shows that trended regression tree method predicts the optimum conditions of SCPP better than other methods. Genetic programming is used to present fitted algebraic functions on Pt and m ˙ and the ratio of turbine pressure drop to pressure potential (PR). Results demonstrate the algebraic relation of PR estimates the PR accurately at each group of variables.

Transmitter design and AE–AR region characterization for NOMA-SLIPT UWOC systems with uniformly distributed message and Imp-SIC

This paper investigates simultaneous lightwave and information transfer (SLIPT) based non-orthogonal multiple access (NOMA) in underwater optical wireless communication (UWOC) systems. At the user signal separation (SS) based SLIPT scheme is employed. Imperfect successive interference cancellation (SIC) at the near user is considered. Firstly, we derive the maximum allowable electrical power for message symbols at the transmitter, ensuring input to the laser diode lies within the linear region and. A novel linearity-constrained transmitter design is proposed for the uniformly distributed message, followed by calculations of instantaneous data rate and instantaneous harvested energy for both users. Then, closed-form expressions for average data rates (AR) and average energy harvested (AE) under weak turbulence-induced fading channels using Holtzman’s approximation are derived. The tightness of the approximation is confirmed by Monte-Carlo simulations. AE–AR boundaries for both users show an initial rise and subsequent decline in data rates with increased harvested energy, owing to higher bias values restricting transmitter power. The study also examines trade-offs between AE and AR across various system parameters including beam divergence angles, imperfection of SIC, power allocation coefficients, and water types, is conducted. We observe shifting and shrinking/expansion of the AE–AR region depending upon the variation of the various system parameters. We also show that the discussed SS scheme is general and encompasses time-switching (TS), and power-splitting (PS) schemes as special cases. We also briefly discuss as to how the developed framework could be extended to more than two users. In summary, the overall effective energy consumption deduces owing to the adoption of SLIPT at the users, making the considered setup more energy-efficient.

Plasmonic-nanowire near-field beam analyzer

Abstract Experimental near-field analysis of the output beams from the end faces of micro/nano-waveguide is very necessary, because important information such as spatial intensity distributions, mode orders, and divergence angles can be obtained, and are very important for investigating and designing nanophotonic devices. However, as far as we know, it has not been demonstrated yet. In this work, we experimentally demonstrate a plasmonic-nanowire near-field beam analyzer, utilizing a single Au nanowire (AuNW) as the probe to scan the spatial near-field distributions of emitted beams from micro/nano-waveguide end-faces. Our analyzer can resolve the trade-off between high measurement resolution and light collection efficiency in conventional beam analyzers by a reverse nanofocusing process, achieving a probe resolution of 190 nm (<λ/8) and a simulated collection efficiency of ∼47.4 % at λ = 1596 nm. These attractive advantages allow us to obtain three‐dimensional (3D) scanning in a large range from the plasmonic hotspot region to the far-field region, characterizing the 3D spatial distribution evolution from a metal nanowire output beam for the first time, with an M 2 factor lower than that of the ideal Gaussian beam (M 2 = 1). In addition, the analyzer also demonstrates simultaneous characterization of multimodes in irregular and large-sized nanoribbons, further verifying its ability to selectively explore complex multimodes that are difficult to be predicted by numerical simulations. Our results suggest that this plasmonic-nanowire beam analyzer may hold promise for diverse near-field applications for micro/nano-waveguides such as nanolasers and biosensing, and offer a new method for understanding nanophotonic structures.

Dual-color emissive OLED with orthogonal polarization modes

Linearly polarized organic light-emitting diodes have become appealing functional expansions of polarization optics and optoelectronic applications. However, the current linearly polarized diodes exhibit low polarization performance, cost-prohibitive process, and monochromatic modulation limit. Herein, we develop a switchable dual-color orthogonal linear polarization mode in organic light-emitting diode, based on a dielectric/metal nanograting-waveguide hybrid-microcavity using cost-efficient laser interference lithography and vacuum thermal evaporation. This acquired diode presents a transverse-electric/transverse-magnetic polarization extinction ratio of 15.8 dB with a divergence angle of ±30°, an external quantum efficiency of 2.25%, and orthogonal polarized colors from green to sky-blue. This rasterization of dielectric/metal-cathode further satisfies momentum matching between waveguide and air mode, diffracting both the targeted sky-blue transverse-electric mode and the off-confined green transverse-magnetic mode. Therefore, a polarization-encrypted colorful optical image is proposed, representing a significant step toward the low-cost high-performance linearly polarized light-emitting diodes and electrically-inspired polarization encryption for color images.

Non-uniform distributed silicon optical phased array for high directionality and a wide steering range.

A non-uniform distributed silicon optical phased array (OPA) is proposed and numerically demonstrated to realize high directionality and a wide range for beam steering. The OPA is composed of grating antennas with dual-layer corrugations along silicon strip waveguides, which can achieve a high directionality of 0.96 and a small divergence angle of 0.084°. To reduce the crosstalk between adjacent antennas and realize a wide steering range, the genetic algorithm is improved and utilized to arrange the locations of grating antennas. As a proof of concept, a 32-channel non-uniform distributed OPA is designed and thoroughly optimized. The simulation results successfully demonstrate a two-dimensional wide steering range of 70∘×18.7∘ with a side-mode suppression ratio (SMSR) over 10dB.