Sewage Sludge Disposal Research Articles

Effect of thermochemical treatment of sewage sludge on its phosphorus leaching efficiency: Insights into leaching behavior and mechanism

Thermochemical conversion, including hydrothermal processing, pyrolysis and incineration, has become a promising technology for sewage sludge (SS) treatment and disposal. Furthermore, acid leaching is considered as an effective method to recover phosphorus (P) from SS and its thermochemical treatment products. This study has investigated the potential of P reclamation from SS and its thermochemical derivatives, including hydrochar (HC), biochar (BC), and SS incinerated ash (SA). Comparative analyses of physicochemical properties of these derivatives revealed a decrease in hydroxyl and aromatic groups and an increase in aliphatic and oxygen-containing functional groups in HC and BC. Leaching experiments using 1 M sulfuric acid (H2SO4) and 1 M oxalic acid (C2H2O4) suggested that H2SO4 slightly outperformed C2H2O4 in terms of P leaching efficiency. HC achieved 79.1 % optimal leaching efficiency in 60 min using H2SO4, while BC, SS, and SA required 360 min to achieve comparable efficiency. SS and BC reached optimal leaching efficiency at 74.1 % and 76.2 % in H2SO4, while SA achieved 80.9 % in C2H2O4. Importantly, HC and SA are more favorable for P extraction using acid leaching, whereas BC tends to be a potential P carrier. Time-dependent kinetics revealed a two-stage leaching process, i.e., fast and slow reaction stages. Shrinking core model indicates product layer diffusion as the primary rate-limiting step in both stages. Overall, these fundamental insights play an important role in practical P recovery through acid leaching of SS derived residues after thermochemical treatment.

Effect of the stabilization process of sewage sludge on the mercury content of municipal sewage sludge

Sewage sludge, the amount of which is increasing every year, must be disposed of on the one hand, and on the other hand it makes a pretty good alternative fuel. However, due to the high mercury content of sewage sludge, its use for energy purposes requires further research. The effect of the technological process of sewage sludge treatment on the mercury content of this end product of wastewater treatment is not fully understood. Therefore, the present study examined 17 sewage sludges from municipal wastewater treatment plants in Lower Silesia for energy properties and mercury content before and after the following technological processes: autothermal aerobic stabilization at temperatures above 50 °C (ATSO), aerobic separated stabilization at effluent temperature (KTSO), separated digestion at ambient temperature (OKF) and separate digestion at 37 °C (WKF). The study showed that the mercury content ranged widely from 0.47 to 6.05 mg/kg Hg, indicating several times higher atmospheric emissions than when using conventional fuels. Among the sewage sludge samples tested, there were samples with very high mercury content, significantly different from the average mercury content of the sludge from the same process line. On this basis, it is concluded that the sewage sludge disposal process leads to the formation of significantly heterogeneous material.Sludge stabilization processes (ATSO, KTSO, OKF, and WKF) increase the mercury content of sewage sludge.

Biochar from Co-Pyrolyzed Municipal Sewage Sludge (MSS): Part 2: Biochar Characterization and Application in the Remediation of Heavy Metal-Contaminated Soils.

The disposal of municipal sewage sludge (MSS) from wastewater treatment plants poses a major environmental challenge due to the presence of inorganic and organic pollutants. Co-pyrolysis, in which MSS is thermally decomposed in combination with biomass feedstocks, has proven to be a promising method to immobilize inorganic pollutants, reduce the content of organic pollutants, reduce the toxicity of biochar and improve biochar's physical and chemical properties. This part of the review systematically examines the effects of various co-substrates on the physical and chemical properties of MSS biochar. This review also addresses the effects of the pyrolysis conditions (temperature and mixing ratio) on the content and stability of the emerging pollutants in biochar. Finally, this review summarizes the results of recent studies to provide an overview of the current status of the application of MSS biochar from pyrolysis and co-pyrolysis for the remediation of HM-contaminated soils. This includes consideration of the soil and heavy metal types, experimental conditions, and the efficiency of HM immobilization. This review provides a comprehensive analysis of the potential of MSS biochar for environmental sustainability and offers insights into future research directions for optimizing biochar applications in soil remediation.

Soil application of activated hydrochar derived from sewage sludge enhances plant growth and reduces nitrogen loss

Sewage sludge treatment and disposal is a considerable environmental and economic burden, and is considered a major global challenge. Here, sewage sludge treatment and disposal were studied with a focus on hydrothermal carbonization and the use of hydrochar (HC) as a soil amendment after Fenton-reaction activation. The underlying hypothesis was that enhanced adsorption of nutrients (e.g., ammonium) by activated HC (AHC) increases their availability, thus enhancing plant growth and reducing environmental impacts such as greenhouse gas emission and N leaching relative to conventional soil-amendment techniques.The impact of AHC on lettuce plant growth, N leaching, ammonia volatilization, soil trace-gas emissions, and respiration was studied in a net-house planting experiment. Four treatments were tested in quadruplicate using sandy loam soil with addition of either AHC, urea fertilizer, or AHC plus urea, and a control with no amendment.Activation-induced changes in AHC surface properties (indicated by SEM and XPS analyses) resulted in an NH4+ adsorption capacity 60 % higher than that of untreated HC. The AHC + urea soil treatment yielded the most enhanced plant growth, followed by urea and AHC treatments with comparable growth rates. Least growth occurred in the control with no amendment. Nitrogen loss through gas emissions, per kg of lettuce, was lowest with AHC + urea treatment, although its mean N emission as nitrous oxide (N2O) was notably higher at 2.3 mg N2O-N kg−1 than for other treatments (∼0.4 mg N2O-N kg−1). Dissolved-N leaching was reduced by up to four times with AHC treatment due to its higher NH4+ adsorption capacity, indicating reduced environmental impact of the AHC amendment.AHC application is therefore considered a sustainable soil amendment, enhancing plant growth and reducing N loss and sewage environmental impact.

Plant litter as a heavy metal migration strategy following application of sewage sludge to subtropical forest soils

The environmental risks of migration of heavy metals (HMs) following applications of sewage sludge (SS) to forest soils are garnering increased attention. Plant litter at the forest floor may modify HM migration pathways through impacts on soil aggregates and water/soil erosion; however, HM migration responses to plant litter are poorly understood. The aim of this study was to determine the effects of plant litter cover on HMs migration, and water and soil erosion following the application of SS to subtropical forest soils. Effects of addition of SS along and SS plus plant litter at 0.75 or 1.5 kg m−2 on the migration of cadmium, chromium, copper, nickel, lead, and zinc in surface runoff, soil interflow, and sediments were quantified across nine simulated rainfall events in a laboratory experiment and following natural intense rain events in a field experiment. Addition of SS elevated HM concentrations in surface runoff by 38.7 to 98.5 %, in soil interflow by 48.3 to 312.5 %, and in sediment by 28.5 to 149.4 %, and increased the production of sediment aggregates <0.05 mm that led to greater cumulative migrations of HMs in surface runoff and sediment; sediment accounted for 89.5 % of HM migrations. Addition of plant litter reduced cumulative migration of HMs by 87.1–97.27 %; however, the higher rate of plant litter led to a decrease in surface runoff and sediment yield, and an increase in soil interflow. Addition of plant litter shifted the main pathway of HM migration from sediment to surface runoff and soil interflow. The potential ecological HM risk index was “low” for each treatment. We found consistency in HM concentrations and migrations via surface runoff between the field and laboratory experiments. Overall, the addition of plant litter with SS mitigated soil erosion and reduced total migration of HMs, resulting in a 88.7–97.3 % decrease in the ecological risk index of the six HMs. We conclude that the addition of plant litter may provide a management strategy for the mitigation of HM risks to environmental safety for the disposal of SS in subtropical forest systems.

Sewage sludge pyrolysis ‘kills two birds with one stone’: Biochar synergies with persulfate for pollutants removal and energy recovery

The disposal and resource utilization of sewage sludge (SS) have always been significant challenges for environmental protection. This study employed straightforward pyrolysis to prepare iron-containing sludge biochar (SBC) used as a catalyst and to recover bio-oil used as fuel energy. The results indicated that SBC-700 could effectively activate persulfate (PS) to remove 97.2% of 2,4-dichlorophenol (2,4-DCP) within 60 min. Benefiting from the appropriate iron content, oxygen-containing functional groups and defective structures provide abundant active sites. Meanwhile, SBC-700 exhibits good stability and reusability in cyclic tests and can be easily recovered by magnetic separation. The role of non-radicals is emphasized in the SBC-700/PS system, and in particular, single linear oxygen (1O2) is proposed to be the dominant reactive oxygen. The bio-oil, a byproduct of pyrolysis, exhibits a higher heating value (HHV) of about 30 MJ/kg, with H/C and O/C ratios comparable to those of biodiesel. The energy recovery rate of the SS pyrolysis system was calculated at 80.5% with a lower input cost. In conclusion, this investigation offers a low-energy consumption and sustainable strategy for the resource utilization of SS while simultaneously degrading contaminants.

The Effect of Remediation of Soil Co-Contaminated by Cu and Cd in a Semi-Arid Area with Sewage Sludge-Derived Biochar

In this study, biochar derived from sewage sludge was applied to remediate Cu and Cd co-polluted soil in semi-arid areas for the first time, in which the effects of biochar on the improvement of soil physicochemical and biological properties as well as the immobilization of Cu and Cd were investigated. Soil water holding capacity increased by 0.22–2.74%, soil CEC increased by 0.52–4.06 units, soil SOM content increased by 1.41–5.97 times, and urease and catalase activities increased by 0.012–0.032 mg·g−1·24 h−1, 0.18–2.95 mg H2O2·g−1, but soil pH increased only slightly by 0.69 units after biochar application. In addition, although the total content of these two metals in the soil increased with the use of biochar, the content of DTPA-Cu and Cd decreased by −0.128–0.291 mg/kg, 0–0.037 mg/kg, with the increase in biochar application, and the content of acid-soluble Cu in the soil decreased from 27.42 mg/kg to 3.76 mg/kg, the mobility and bioavailability of these two metals in the soil decreased. Finally, the complexation of organic functional groups with the soil dominates the immobilization process of metals, especially Cu. These findings suggest that biochar from sewage sludge can effectively improve soil quality and remediate heavy metal-contaminated soils in semi-arid regions. Meanwhile, the use of sludge-based biochar for the remediation of contaminated soils also provides a new method for the safe disposal of sewage sludge and a new way for sustainable development. In subsequent studies, methods such as modification are recommended to improve the efficiency of sludge-based biochar for the removal of Cu and Cd.

Life cycle assessment of sewage sludge treatment and disposal technologies based on carbon emissions and environmental impacts

ABSTRACT This study aimed to create a comprehensive evaluation method for sewage sludge (SS) treatment and disposal technologies, considering carbon emission and environmental impacts. Life cycle assessment (LCA) were conducted on six SS treatment and disposal technologies in China. The assessments used the IPCC emission factor approach to calculate carbon emissions and the CML2001 method to determine environmental impact factors. Additionally, a colour-coded method was implemented to quantify the evaluation results. The study found that S1 (anaerobic digestion + land application) had the lowest carbon emissions and environmental impact, making it the optimal technology. The S1 scenario had carbon emissions of 669 kg CO2(t DS)−1 and environmental impacts of 5.20E-10. A sensitivity analysis was conducted to show the impacts of each unit in the six technologies on total carbon emissions and environmental impacts. The results showed that landfilling has a high sensitivity to carbon emissions and environmental impacts. Therefore, controlling greenhouse gases and toxic substances in sludge landfills is crucial for reducing carbon emissions and environmental pollution.

Co-pyrolysis of sewage sludge with hydrogen-rich polythene: Effects on synergistic promotion and bio-oil quality

Co-pyrolysis of biomass with hydrogen-rich feedstock is a promising technology to improve bio-oil quality, in which understanding the synergistic effects and product of sewage sludge (SS) with two types of plastic waste (HDPE, LDPE) is essential to develop co-pyrolysis technology. This work used in situ tracking to detect co-pyrolysis promotion/inhibition effects with different mixed feedstocks and mixing ratios, and analyzed volatile and bio-oils in detail. The results show that co-pyrolysis synergistic promotion was mainly created by the release of a large amounts of free radicals, and the largest promotion occurred near the maximum mass loss rate (DTGmax). The synergistic promotion effect was 190 % higher for SS mixed with HDPE (S–H) than for SS mixed with LDPE (S-L). Co-pyrolysis reduced polluting gases (e.g., NO2, and SO2), enhanced the degradation of oxygenated functional groups, contains 2.7 times of hydrocarbons in bio-oil than SS mono-pyrolysis. S-L promoted short-chain generation and produced more naphthalene compounds (e.g., methylnaphthalene and 2-methylnaphthalene) in hydrocarbons. However, S–H tends to produce longer chains and more monocyclic aromatic hydrocarbons (e.g., alkylbenzenes). The gasoline fraction in bio-oil could reach 89.7 % (S7L3) and 55.8 % (S5H5). This information helps to promote clean disposal and resource utilization of sewage sludge and plastic waste through co-pyrolysis.

Enhanced uranium removal from leach liquor using raw and activated sludge as sustainable adsorbents

ABSTRACT To eliminate uranium from sulphate leach solution, this study introduces an economical, environmentally friendly adsorbent derived from dewatered municipal sludge (RS) and activated (AS) using calcium oxide. Various analytical methods, including scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), Fourier transform infrared spectroscopy (FTIR), Brunauer – Emmett – Teller (BET) analysis, and X-ray fluorescence spectroscopy (XRF), were employed in the characterisation of both materials. The efficacy of these adsorbents in removing uranium from sulphate leach fluid was systematically explored resulting in the achievement of a maximum adsorption capacity of 33.0 mg g−1 and 60.2 mg g−1 for RS and AS respectively. These adsorption capacity were detected using the following operational parameters: solution pH equals 2.0, 240 min as a contact time between the adsorbent and U(VI) solution, U(VI) initial concentration of 250 mg L−1, adsorbent dosage of 5.0 g L−1 and room temperature. The pseudo-second order kinetic and Langmuir isotherm models were determined to be the most suitable for the U(VI) adsorption process, showing a chemisorption, monolayer, and uniform process for the uranium adsorption by both materials. Using 1.0 M hydrochloric acid, over 96% of the U(VI) was successfully desorbed from the loaded sorbent, and AS sorbent held its stability for six sorption/desorption cycles in a row. Overall, this study offers a promising solution for sewage sludge disposal while addressing economic and environmental concerns.

Behaviour of sewage sludge based lightweight aggregate in geopolymer concrete

The global challenge of sewage sludge disposal has encouraged innovative solutions aimed at reducing environmental impact while simultaneously addressing the growing demand for sustainable construction materials. This study aimed to develop treated raw sewage sludge-based lightweight aggregates with strength comparable to commercially available aggregates. Two methods, namely cold bonding and sintering, were employed for the formation of aggregates. The sintering method produced well-formed and hard aggregates, while the cold bonded aggregates exhibited weakness and disintegrated under the slightest pressure. The optimal mix for quality aggregates was found to be 10%–20% sewage sludge, 70%–80% fly ash, and 10% lime using the sintering method. In the sintering method, an increase in sewage sludge content resulted in the reduction of bulk density and specific gravity by 13% and 4% respectively due to the high organic content in sewage sludge, volatile gas release, and porous structure formation. When 10% to 20% sewage sludge content was added, water absorption of the aggregates also increased by approximately 2%. Physical properties such as individual pellet strength. aggregate crushing value reduced by 18%, 20% respectively and the aggregate impact value increased by about 9%. These aggregates were then used to produce lightweight geopolymer concrete, which exceeded the design strength by 7% for the aggregate containing 20% sewage sludge and demonstrated excellent physical properties. The use of waste-based aggregates offers advantages including savings in cost, sustainability, resource conservation, waste reduction, and reduced environmental impact, making them a valuable alternative to natural crushed stone aggregates in specific applications.

Research progress and perspective on sludge anaerobic digestion technology: A bibliometric analysis.

Rational disposal of sludge is an ongoing concern. This work is the first attempt for in-depth statistical analysis of anaerobic digestion (AD) research in recent three decades (1986-2022) using both quantitative and qualitative approaches in bibliometrics to investigate the research progress, trends and hot spots. All publications in the Web of Science Core Collection database from 1986 to April 4, 2022 were analyzed. Results showed that the research on AD started in 1999 and the number of papers significantly increased since 2012. The research about the disposal of sewage sludge mainly focuses on energy recovery (e.g. methane and short chain volatile organic acids) by AD. Besides, different pretreatment technologies were studied in this study to eliminate the negative effects on the disposal of sludge caused by hydrolysis (rate-limiting step of AD), water content (increasing the costs) and heavy metal (toxic to the environment) of sludge. Of those, the treatment technologies related to direct interspecies electron transfer were worth further studied in the future. Towards that end, iron conductive material, iron-based advanced oxidation and biological treatment were concluded as the prospective technologies and worth to further study.

Efficient removal of heavy metals from sewage sludge using a low-cost protic ionic liquid: Investigation of mechanism and ecological risk

Land utilization for the disposal of sewage sludge (SS) is an effective strategy, yet the existence of heavy metals (HMs) in the SS represents critical constraints to its implementation on a larger scale. By the principles of simple synthesis steps and low synthesis cost, a low-cost double cationic protic ionic liquid was produced in this study for HMs removal from SS. The influence of reaction time, protic ionic liquid to SS mass ratio, and reaction temperature on HM removal were thoroughly investigated. This result indicated that the integration of protic ionic liquid and heat treatment was efficacious in the efficient elimination of HMs. Under 60°C, 15 min, and protic ionic liquid: SS of 0.5, the removal efficiency of Zn, Fe, Ni, and Cd exceeded 80%, and Cr achieved a removal efficiency of up to 93%. The BCR sequential extraction procedure and calculation of the potential ecological risk index revealed a significant reduction in the ecological risk associated with the treated SS, transitioning from a high to a low-risk level. The alterations in elemental and chemical bonding within the solid phase of SS and changes in polysaccharide and fluorescence properties within the liquid phase of SS were investigated using redundancy analysis, two-dimensional correlation analysis, and parallel factor analysis. These findings suggest that dehydration, deamination, and decarboxylation reactions may be responsible for removing HMs within SS. These findings have a positive impact on further elucidating the effects of protic ionic liquid in SS pretreatment, thereby facilitating the efficient utilization of municipal SS resources.

Synergistic treatment of sewage sludge and food waste digestate residues for efficient energy recovery and biochar preparation by hydrothermal pretreatment, anaerobic digestion, and pyrolysis

The safe disposal of sewage sludge (SS) and food waste digestate residues (DR) is a tough issue considering the difficulty of dewatering and the environmental risks from heavy metals and pathogens. This study combined hydrothermal pretreatment (HP), anaerobic digestion (AD), and pyrolysis to synergistically dispose of SS and DR to enhance dewaterability, recover energy, and prepare biochar with heavy metal immobilization. The results showed that the solid contents of centrifuged cakes increased after HP at 180 °C of SS with the addition of 25% and 50% mass fractions of DR. The centrate from co-HP had a high chemical oxygen demand (COD) and was further treated by AD at 37 °C, producing 193.75 and 210.39 mL/g CODinput (25 °C and 1 atm) of cumulative CH4 under the addition of 50% and 75% mass fractions of DR, respectively. The methanogenic types in AD converted from hydrogen utilization to acetic acid utilization with increasing DR ratio. Zn, Cu, Ni, and Pb were primarily left in the biochar after 50% mass fraction of DR was mixed in the HP combined with pyrolysis at 700 °C; the chemical fractionation of Zn, Cu, Cr, and Pb in the biochar increased to over 85% of the residual fractions, resulting in the lowest potential ecological risk index (15.22, low risk). The CH4 produced from the AD of the co-HP centrate (50: 50, w/w) can supply heat for the HP process, reducing the energy input by 89%. This co-disposal strategy can effectively recover carbon resources from solid wastes to reduce carbon emissions.

Environmental sustainability practice of sewage sludge and low-rank coal co-pyrolysis: A comparative life cycle assessment study

This study attempts to bridge the current research gaps related to the environmental burdens of low-rank coal (LRC) and sewage sludge (SS) co-pyrolysis potentially. The life cycle assessment (LCA), energy recovery and sensitivity analysis were investigated for different proportions of LRC and SS (co-)pyrolysis. The results showed that the LRC/SS pyrolysis mitigated the environmental burden with an average improvement of 43 % across 18 impact categories compared with SS pyrolysis. The best net values of energy and carbon credits were identified in SL-4 with −3.36 kWh/kg biochar and −1.10 CO2-eq/kg biochar, respectively. This study firstly proposed an optimal LRC/SS co-feed proportion at 3 to 7, which achieves the acceptable environmental burden and satisfactory energy recovery. Moreover, sensitivity analysis demonstrated this proportion is robust and adaptable. LRC/SS co-pyrolysis is a promising and sustainable alternative for SS disposal, which could meet the imperative of carbon emission mitigation and resource recycling.

Practical strategies of phosphorus reclamation from sewage sludge after different thermal processing: Insights into phosphorus transformation

In the context of circular economy and global shortage of phosphorus (P) fertilizer production, it is crucial to effectively recover P during the treatment and disposal of sewage sludge (SS). Although thermal treatment of SS has been widely applied, a targeted P reclamation route is not yet well established. This study has comprehensively investigated and compared the physicochemical properties of SS and solid residues (hydrochar (HC), biochar (BC), sewage sludge ash (SSA), hydrochar ash (HCA), and biochar ash (BCA)) after application of three typical thermal treatment techniques (i.e., hydrothermal carbonization (180‒240 °C), pyrolysis (400‒600 °C) and combustion (850 ℃). P speciation and transformation during thermal processes were extensively explored followed by a rational proposal of effective P reclamation routes. Specifically, thermal processing decomposed organic P and converted non-apatite P to apatite P. Orthophosphate-P was found to be the main species in all samples. Physicochemical properties of the resulting thermal-derived products were significantly affected by the thermal techniques applied, thereby determining their feasibility for different P reclamation purposes. In particular, ash is not recommended for agricultural use due to higher harmful metals content, while acid leaching can be an alternative solution to synthesize non-Fe-containing P products because of the lower co-dissolved Fe content in the leachate. HC and BC offer the option for synthesis of Fe containing products. Eventually, HC and BC demonstrate great potential for agriculture application, however, a comprehensive risk assessment should be conducted before their real-world applications.

High-Temperature Ash Melting and Fluidity Behavior upon the Cocombustion of Sewage Sludge and Coal.

Wastewater treatment produces a large amount of sludge, where the minimizing of the disposed sludge is essential for environmental protection. The co-combustion of sludge with coal is a preferable method for sewage sludge disposal from the economic and environmental perspective. The co-combustion of sludge has been widely used in the industry with the advantages of large processing capacity. The melting characteristics of ash are an important criterion for the selection of the co-combustion methods and furnace types. In this study, two types of sludge and four types of coal with different ash melting points were selected, where the ash melting behavior upon co-combustion is investigated by experimental and thermodynamical approaches. Especially, the slag fluidity upon co-combustion is explored via a modified inclined plane method. It has been found that the presence of SiO2 and CaO in sludge substantially enhances its fusion temperature owing to the high content of CaO, while SiO2 acts as a solvent, facilitating the co-melting of other oxides and raising the sludge fusion temperature. Fe2O3 exhibits a specific mass fraction within the range of 10-20%. Furthermore, the presence of CaO and SiO2 prohibits the flow ability of the slag at high temperatures, and Fe2O3 promotes the flow ability for sludge at high temperatures. With increasing base/acid ratio, the sludge flow velocity increases remarkably and peaks at 1.6. The interaction between Fe-Ca and Si-AI significantly affects the fluidity significantly. The findings are expected to optimize the condition of co-combustion and desirable furnace design for the incineration of sludge.

Sewage sludge amendment of rice as a potential alternative to mineral fertilizer: Analyses of physiological, biochemical and molecular mechanisms of plant response

Sewage sludge (SS) disposal poses environmental concerns, yet its organic matter, macro- and micronutrients, make it potentially beneficial for enhancing soil quality and crop yield. This study focuses on three types of SS: “R10” (SS1), which is commonly used in agricultural practices, and two environmentally friendlier options (SS2 and SS3), as alternatives to mineral fertilizer (urea) for rice cultivation. A pot experiment was conducted to investigate the ecophysiological, biochemical, and molecular responses of rice at three different growth stages. SS application led to a significant increase in biomass production (particularly SS3), along with increased nitrogen (N) levels. Enhanced chlorophyll content was observed in SS-treated plants, especially during inflorescence emergence (with the highest content in SS3 plants). At the ecophysiological and biochemical levels, SS treatments did not adversely affect plant health, as evidenced by unchanged values of maximal PSII photochemical efficiency and malondialdehyde by-products. At biochemical and gene expression levels, antioxidant enzyme activities showed transient variations, likely related to physiological adjustments rather than oxidative stress. Ascorbic acid and glutathione did not significantly vary. This study concludes that the use of SS in soil can be a viable alternative fertilizer for rice plants, with positive effects on biomass, chlorophyll content, and no adverse effects on plant health. Among the tested SSs, SS3 showed the most positive effect, even compared to commercial fertilizer. These results suggest that SS application could improve rice yield while addressing environmental concerns surrounding SS disposal.

Data-driven approach for sustainable geopolymer mortar production with treated sewage sludge

ABSTRACT This paper highlights an innovative approach to address the environmental challenges associated with waste management and construction materials. The study presents a new technique for utilising treated sewage sludge in the production of eco-friendly geopolymer mortar. Sewage sludge is a byproduct generated from wastewater treatment plants that poses significant environmental issues due to its disposal problems. Geopolymer mortar, on the other hand, is a sustainable construction material that can be produced by activating industrial waste materials, such as fly ash, using alkaline activators. By integrating machine learning algorithms and data visualisation techniques, this study optimises the mix parameters of geopolymer mortar while simultaneously reducing the negative impact of sewage sludge disposal. The experimental results show that sewage sludge ash can replace fly ash and fine aggregate in 1:3 geopolymer mortar by up to 30% and 20%, respectively, without any toxic or heavy metal residues. The compressive and flexural strength of the sludge-based mortar were comparable to ordinary geopolymer mortar, while water absorption and drying shrinkage were similar to control specimens. This research offers a unique solution to promote sustainability in waste management and construction industry by utilising waste materials, including fly ash and treated sewage sludge, for geopolymer production.

Treatment and Disposal of Sewage Sludge: Assessment of Effectiveness and Efficiency for the Purposes of Tariff Regulation of Wastewater Disposal companies

The possibilities of economic justification for activities related to the treatment and disposal of sewage sludge are considered by assessing their effectiveness and efficiency. Two assessment methods are proposed: based on integral target indicators and based on a risk-based approach. A combined assessment of the effectiveness and efficiency of production and investment program activities is recommended. It is based on the main regulatory documents regulating the field of wastewater disposal. It is noted that the use of this approach will provide regulatory and regulated institutions with an effective mechanism for economic argumentation of the process costs related to the treatment of sewage sludge.