Surface Disinfection Research Articles

Light-Field Optimization of Deep-Ultraviolet LED Modules for Efficient Microbial Inactivation

Public awareness of preventing pathogenic microorganisms has significantly increased. Among numerous microbial prevention methods, the deep-ultraviolet (DUV) disinfection technology has received wide attention by using the nitride-based light-emitting diode (LED). However, the light extraction efficiency of DUV LEDs and the utilization rate of emitted DUV light are relatively low at the current stage. In this study, a light distribution design (referred to as the reflective system) was explored to enhance the utilization of emitted DUV from LEDs, leading to successful and efficient surface and air disinfection. Optical power measurements and microbial inactivation tests demonstrated an approximately 79% improvement in average radiation power density achieved by the reflective system when measured at a 5 cm distance from the irradiation surface. Moreover, a statistically significant enhancement in local surface disinfection was observed with low electric power consumption. The reflective system was integrated into an air purifier and underwent air disinfection testing, effectively disinfecting a 3 m3 space within ten minutes. Additionally, a fluorine resin film at the nanolevel was developed to protect the light module from oxidation, validated through a 1200 h accelerated aging test under humid conditions. This research offers valuable guidance for efficient and energy-saving DUV disinfection applications.

Optimization of the bioethanol dehydration process using MgCl2 as mass separating agent

Ethanol derived from lignocellulosic sources is an important chemical that can have several uses such as biofuel that can be blended with gasoline, as sanitizer for the disinfection of surfaces, or as additive in the food, cosmetic and pharmaceutical industry. Nevertheless, its separation poses a challenge because it must be separated from water and this mixture forms an azeotrope. This research focuses on the ethanol dehydration using magnesium chloride (MgCl2) as a mass separating agent, which is an innocuous chemical used in the food industry to process Tofu. Therefore, it does not have any side effect, or it is not harmful for humans. Therefore, the use of this salt makes possible to use the purified ethanol as an additive in the food, cosmetic, or pharmaceutical industry. The proposed separation process is optimized using surrogate nonlinear models for the preconcentration and salt evaporation units. The results showed that using magnesium chloride dodecahydrate is a feasible alternative to bioethanol valorization.

Evaluation of germicidal ultraviolet-C disinfection in a real-world outpatient health care environment

The coronavirus disease 2019 pandemic has highlighted the need for effective infection control in outpatient healthcare settings. Germicidal ultraviolet-C (GUV) light, known for inactivating microorganisms by damaging their deoxyribonucleic acid or ribonucleic acid, offers a potential solution. This study examines the efficacy of GUV air disinfection systems in real-world outpatient environments. We deployed upper-room and far-UV GUV fixtures in 3 outpatient facilities, assessing their impact on bacterial loads through air and surface sampling and bioindicator tests. Occupancy was also monitored. While manual air and surface sampling did not show a significant difference in bacterial loads between control and Ultraviolet C-treated groups, bioindicator tests demonstrated a high level of spore inactivation (up to 99.7% for upper-room GUV and 96.26% for far-UV). Occupancy levels did not significantly influence these outcomes. The discrepancy between bioindicator efficacy and environmental sampling results suggests limitations in the latter's ability to accurately capture environmental bioburden. Bioindicators proved to be reliable for in-situ validation of Ultraviolet C surface disinfection. Bioindicators are effective for validating GUV surface disinfection efficacy in healthcare settings, though further research is needed to optimize environmental sampling methods for assessing GUV's impact on real-world bacterial loads.

UVC Stokes and Anti-Stokes Emission of Ca9Y(PO4)7 Polycrystals Doped with Pr3+ Ions.

The recent COVID-19 pandemic has made everyone aware of the threat of viruses and the growing number of antibiotic-resistant bacteria. It has become necessary to find new methods to combat these hazards. One tool that could be used is UVC radiation, i.e., 100-280 nm. Currently, the available sources of this light are mercury vapor lamps. However, the modern world requires more compact, mercury-free, and less energy-consuming light sources. This work presents the results of our research on a new material in which efficient UVC radiation was obtained. Here, we present the results of research on Ca9Y(PO4)7 polycrystals doped with Pr3+ ions prepared using the solid-state method. The absorption, excitation, emission, and emission decay profiles of praseodymium(III) ions were measured and analyzed. The upconversion emission in the UVC region excited by blue light was observed. Parameters such as energy bandgap, refractive index, and thermal stability of luminescence were determined. The studied phosphate-based phosphor possesses promising characteristics that show its potential in luminescent applications in future use in medicine or for surface disinfection.

Kinetics of inactivation of bacteria responsible for infections in hospitals using UV-LED

Controlling the microbial load in the environment is crucial to prevent the spread of organisms. The continuous spread of nosocomial infections in hospital facilities and the emergence of the coronavirus (COVID-19) highlighted the importance of disinfection processes in health safety. This work aimed to evaluate the effectiveness of LED-based disinfection lamps on bacteria from the ESKAPEE group and virus phage in vitro inactivation to be applied in hospital environments and health facilities disinfection.This study evaluated the effect of different UV wavelengths (275 nm, 280 nm (UVC), 310 nm (UVB) and 340 nm (UVA)) on the disinfection process of various microbial indicators including E. coli, S. aureus, P. aeruginosa, B. subtilis and Bacteriophage lambda DSM 4499. Exposure time (5 min–30 min), exposure distance (0.25 m and 0.5 m) and surface materials (glass, steel, and polished wood) were evaluated on the disinfection efficiency. Furthermore, the study determined the recovery capacity of each species after UV damage.UVC-LED lamps could inactivate 99.99 % of microbial indicators after 20 min exposures at a 0.5 m distance. The exposure time needed to completely inactivate E. coli, S. aureus, P. aeruginosa, B. subtilis and Bacteriophage lambda DSM 4499 can be decreased by reducing the exposure distance. UVB-LED and UVA-LED lamps were not able to promote a log reduction of 4 and were not effective on B. subtilis or bacteriophage lambda DSM 4499 inactivation. Thus, only UVC-LED lamps were tested on the decontamination of different surface materials, which was successful. P. aeruginosa showed the ability to recover from UV damage, but its inactivation rate remains 99.99 %, and spores from B. subtilis were not completely inactivated. Nevertheless, the inactivation rate of these indicators remained at 99.99 % with 24 h incubation after UVC irradiation. UVC-LED lamps emitting 280 nm were the most indicated to disinfect surfaces from microorganisms usually found in hospital environments.

UV-C side-emitting optical fiber-based disinfection: a promising approach for infection control in tight channels.

The growth of pathogenic bacteria in moist and wet surfaces and tubing of medically relevant devices results in serious infections in immunocompromised patients. In this study, we investigated and demonstrated the successful implementation of a UV-C side-emitting optical fiber in disinfecting medically relevant pathogenic bacteria (Pseudomonas aeruginosa and Methicillin-resistant Staphylococcus aureus [MRSA]) within tight channels of polytetrafluoroethylene (PTFE). PTFE is a commonly used material both in point-of-use (POU) water treatment technologies and medical devices (dental unit water line [DUWL], endoscope). For a 1-m-long PTFE channel, up to ≥6 log inactivation was achieved using a 1-m-long UV side-emitting optical fiber (SEOF) with continuous 16-h exposure of low UV-C radiation ranging from ~0.23 to ~29.30 μW/cm2. Furthermore, a linear model was used to calculate the inhibition zone constant (k`), which enables us to establish a correlation between UV dosage and the extent of inactivated surface area (cm2) for surface-bound Escherichia coli on a nutrient-rich medium. The k` value for an irradiance ranging from ~150 to ~271.50 μW/cm2 was calculated to be 0.564 ± 0.6 cm·cm2/mJ. This study demonstrated the efficacy of SEOFs for disinfection of medically relevant microorganisms present in medically and domestically relevant tight channels. The impact of the results in this study extends to the optimization of operational efficiency in pre-existing UV surface disinfection setups that currently operate at UV dosages exceeding the optimal levels.IMPORTANCEGermicidal UV radiation has gained global recognition for its effectiveness in water and surface disinfection. Recently, various works have illustrated the benefit of using UV-C side-emitting optical fibers (SEOFs) for the disinfection of tight polytetrafluoroethylene (PTFE) channels. This study now demonstrates its impact for disinfection of medically relevant organisms and introduces critical design calculations needed for its implementation. The flexible geometry and controlled emission of light in these UV-SEOFs make them ideal for light distribution in tight channels. Moreover, the results presented in this manuscript provide a novel framework that can be employed in various applications, addressing microbial contamination and the disinfection of tight channels.

A versatile plasma generation power supply featuring a multilevel converter for arbitrary waveforms generation

Purpose Plasma technology has become of great interest in a wide variety of industrial and domestic applications. Moreover, the application of plasma in the domestic field has increased in recent years due to its applications to surface treatment and disinfection. In this context, there is a significant need for versatile power generators able to generate a wide range of output voltage/current ranging from direct current (DC) to tens of kHz in the range of kVs. The purpose of this paper is to develop a highly versatile power converter for plasma generation based on a multilevel topology. Design/methodology/approach This paper proposes a versatile multilevel topology able to generate versatile output waveforms. The followed methodology includes simulation of the proposed architecture, design of the power electronics, control and magnetic elements and test laboratory tests after building an eight-level prototype. Findings The proposed converter has been designed and tested using an experimental prototype. The designed generator is able to operate at 10 kVpp output voltage and 10 kHz, proving the feasibility of the proposed approach. Originality/value The proposed converter enables versatile waveform generation, enabling advanced studies in plasma generation. Unlike previous proposals, the proposed converter features bidirectional operation, allowing to test complex reactive loads. Besides, complex waveforms can be generated, allowing testing complex patterns for optimized cold-plasma generation methods. Besides, unlike transformer- or resonant-network-based approaches, the proposed generator features very low output impedance regardless the operating point, exhibiting improved and reliable performance for different operating conditions.

Ultraviolet light C prototype device against Sporothrix brasiliensis as a potential physical method for surface disinfection.

Sporothrix brasiliensis is recognized as an emergent fungal pathogen and the high amount of fungal propagules in the lesions of infected cats allows the contamination of surfaces by direct contact. Given that the environment can play a role in the transmission of this fungus, effective methods to eliminate this pathogen from contaminated surfaces are necessary. Physical methods, such as ultraviolet light C (UVC), are broad used for surfaces disinfection, however, non-data about its activity against S. brasiliensis is reported. Therefore, we aimed to evaluate an easy handled prototype of a UVC device, in the inhibition of S. brasiliensis. Three doses and times of exposure of irradiance were tested: 3.5mJ/cm2 (1s), 5.25mJ/cm2 (1.5s) and 329mJ/cm2 (94s) against a standardized inoculum of yeast and mold phase of S. brasiliensis. A decrease in CFU was shown in all doses of irradiance in both phases of S. brasiliensis, the average reduction ranged from 78 to 100% among doses, being a complete fungicidal activity achieved against the yeast phase after the 94s exposure (329mJ/cm2). Our data shows that UVC is a potential physical method for disinfection of surfaces contaminated with S. brasiliensis, and the prototype device developed provides an easy handling, and quickly results.

Eco-Friendly Sanitization of Indoor Environments: Effectiveness of Thyme Essential Oil in Controlling Bioaerosol Levels and Disinfecting Surfaces.

Bioaerosols and pathogens in indoor workplaces and residential environments are the primary culprits of several infections. Techniques for sanitizing air and surfaces typically involve the use of UV rays or chemical sanitizers, which may release chemical residues harmful to human health. Essential oils, natural substances derived from plants, which exhibit broad antimicrobial properties, could be a viable alternative for air and surface sanitation. The objective of this study has been to investigate the efficacy of thyme essential oil (TEO) in environmental sanitation processes. In Vitro assays through agar well diffusion, disk volatilization and tube dilution methods revealed significant antimicrobial activity of TEO 100% against foodborne and environmental isolates, with both bacteriostatic/fungistatic and bactericidal/fungicidal effects. Therefore, aqueous solutions of TEO 2.5% and 5% were formulated for air sanitation through nebulization and surface disinfection via direct contact. Bioaerosol samples and surface swabs were analyzed before and after sanitation, demonstrating the efficacy of aqueous solutions of TEO in reducing mesophilic and psychrophilic bacteria and environmental fungi levels in both air and on surfaces. The obtained results prove the antimicrobial potential of aqueous solutions of TEO in improving indoor air quality and surface cleanliness, suggesting thyme essential oil as an effective and safe natural sanitizer with minimal environmental impact compared to dangerous chemical disinfectants.

Towards a standardised orchid germination protocol: determining the optimal duration of chemical scarification for orchid seeds by means of viability and permeability staining

Complex nutrient media are used for the germination of orchids in the laboratory. These substrates are also suitable for the growth of microbes and thus the sterilization of both the medium and the seeds prior to sowing is mandatory. The surface disinfection of orchid seeds with chemical substances eliminates possible infections and enhances germination in several cases, by chemically scarifying their seed coats. However, long durations of chemical treatments may result in viability loss, and consequently, precisely determining the optimal treatment duration is essential for developing effective germination protocols. In this study, the double staining technique with Tetrazolium Chloride and Trypan Blue is tested as a proxy method to determine the optimal chemical treatment duration for 10 orchid taxa of Greece. Various durations of chemical treatment with 5% Ca(OCl)2 were carried out on independent seed samples which were subsequently tested, pairwise, for both germination and viability. The results in the corresponding experiments are extraordinarily similar and we conclude that the double viability staining is a quick and accurate technique in determining the permeability and optimal duration for chemical scarification prior to germination experiments. The storability potential of the taxa studied is discussed in comparison with previous data of the NKUA Seed Bank.

Shedding light on the problem: Influence of the radiator power, source-sample distance, and exposure time on the performance of UV-C lamps in laboratory and real-world conditions.

Effective surface disinfection is crucial for preventing the spread of pathogens in hospitals. Standard UltraViolet-C (UV-C) lamps have been widely used for this purpose, but their disinfection efficiency under real-world conditions is not well understood. To fill this gap, the influence of the power of the ultraviolet radiator, source-sample distance, and exposure time on the performance of UV-C lamps against Escherichia coli and Staphylococcus epidermidis were experimentally determined in the laboratory and hospital. The obtained results showed that the UV irradiance and, thus, the UV-C disinfection efficiency decreased significantly at distances greater than 100 cm from the UV-C lamp. Moreover, increasing the total power of the radiators does not improve the performance of UV-C lamps under real conditions. The UV-C disinfection efficiency greater than 90% was achieved only under laboratory conditions at a close distance from the UV-C lamp, i.e., 10 cm. These findings provide novel insights into the limitations of UV-C lamps in real-world conditions and highlight the need for more effective disinfection strategies in hospitals.

First Report of Globisporangium (Pythium) mastophorum causing Damping-off / Root Rot on Parsley in Slovenia.

Pythium-like species cause damping-off symptoms of various hosts, including umbelliferous crops. In April 2023, parsley plantlets (Petroselinum crispum), showing stunted growth, yellowing, decayed roots and damping-off, were obtained from a nursery in central Slovenia, where parsley was grown in polystyrene trays in a greenhouse. Nearly 30% of plants were symptomatic. Sampled roots of ten plants contained ornamented oogonia (avg. 33.3 ± 1.4 µm in diam) with conical projections (5.2 ± 0.5 µm long) (Figure S1 A, B) in microscopically analyzed squash mounts. The pathogen was isolated from root pieces treated for surface disinfection with 0.5% sodium hypochlorite for 30 s, and washed with sterile water. Four 1-2 mm root pieces were taken from each of 10 plants, plated on the selective medium P5ARP, and incubated at 21 °C. Mycelia emerging from root pieces were transferred to carrot piece agar (CPA). Twenty-two equally looking oomycetous colonies were obtained; all sampled plants were infested. Oogonia formed by all colonies were similar to those observed on decayed roots and suggested that Globisporangium (Pythium) mastophorum is the causal disease agent. Analyses of partial β-tubulin (Kroon et al. 2004) and mitochondrial cytochrome c oxidase I (COI) gene sequences (Robideau et al. 2011) confirmed the identification. Obtained COI (Genbank accession number OR725417) sequence was 100% identical to that from G. mastophorum strain CBS 375.72 (EU350523), whereas the β-tubulin sequence (OR725416) corresponded to 99.6 % pairwise identity (KJ595502). Further, pathogenicity of an obtained isolate was tested on 4 wk-old curly leaf (cv. Petra F1) parsley. Half of a 7 d-old CPA culture, consisting of mycelium and oogonia, was finely cut and mixed with ca 50 ml of nonsterile commercial substrate (Potgrond H, AGRO-FertiCrop) in each of six 400 ml pots. Pots were filled with ca 300 ml additional substrate, into which 5 parsley seedlings were planted. Control plants were treated equally but with sterile CPA. Plantlets were watered with sterile tap water and held at ambient light conditions and temperature (night 18 °C - day 23 °C). After 14 d, inoculated plants started wilting and yellowing and showed stunted growth. After 21 d, roots were severely decayed and the seedlings damped-off (Figure S1 C). Four pieces each from 10 decayed roots were plated. Thirty-one pieces revealed pythium-like colonies. Obtained isolates were morphologically identical to the strain used for inoculation and identified as G. mastophorum. Control plants developed no foliar or root symptoms and no pythium-like species was obtained. Agricultural advisors observed occurrence of parsley damping-off also in other nurseries in Slovenia what may lead to spreading the pathogen to parsley in production fields and private gardens. The case emphasizes the need for implementing phytosanitary measures in order to eliminate primary inoculum. Reports from field-infected plants showed that G. mastophorum is a pathogen of parsley in Australia (Petkowski et al. 2013) and the USA (Tsuchida et al. 2018), and celery in the Czech Republic (Šafránková and Holková 2017). Others isolated G. mastophorum from parsley in The Netherlands (online database of the Westerdijk Fungal Biodiversity Institute, strain CBS 243.86). However, the here described case is, to the best of our knowledge, one of the rare documentations of damping-off due to G. mastophorum in Europe (Šafránková and Holková 2017) and the first in Slovenia. Funding: The work was funded by the Ministry of Agriculture, Forestry and Food of Slovenia, and Slovenian Research and Innovation Agency (ARIS Programs P4-0431 and P4-0072).

Disinfection of needleless connectors for catheters in one second using a hand-held UV device

The standard of care for disinfecting needleless connectors (NCs) of central venous catheters includes alcohol-containing caps or up to a 15-second scrub with alcohol or chlorhexidine. Due to the clinical impact and high cost of treating Central line-associated bloodstream infections (CLABSI), reducing the incidence of CLABSI is a priority for public health and of the Centers for Disease Control. Alcohol-containing caps have been demonstrated to disinfect external NC surfaces, but not the internal surface. Ultraviolet light (UV-C) is a strategy for disinfection of NC internal and external surfaces. Four clinically relevant bacteria (Staphylococcus aureus, Staphylococcus epidermidis, Escherichia coli,Pseudomonas aeruginosa) and Candida albicans were inoculated on NCs. Disinfection efficacy was measured after exposure to one second of 285nm UV-C light at 48mW/cm2 in a proprietary handheld device and UV-C transparent NC or standard of care. Disinfection of internal and external surfaces of NC inoculated with S aureus using alcohol caps, and UV-C was also compared. A 4-log reduction in colony forming units (CFUs) on the interior and exterior surfaces of the UV-transparent NC of clinically relevant pathogens was observed with UV-C light at this power for 1second. We demonstrated the efficacy of UV-C for the disinfection of NCs in one second using the UV-C device in benchtop studies. This device holds promise for reducing CLABSI, and clinical studies are planned.

Chimeric Amphiphilic Disinfectants: Quaternary Ammonium/Quaternary Phosphonium Hybrid Structures.

Cationic biocides play a crucial role in the disinfection of domestic and healthcare surfaces. Due to the rise of bacterial resistance towards common cationic disinfectants like quaternary ammonium compounds (QACs), the development of novel actives is necessary for effective infection prevention and control. Toward this end, a series of 15 chimeric biscationic amphiphilic compounds, bearing both ammonium and phosphonium residues, were prepared to probe the structure and efficacy of mixed cationic ammonium-phosphonium structures. Compounds were obtained in two steps and good yields, with straightforward and chromatography-free purifications. Antibacterial activity evaluation of these compounds against a panel of seven bacterial strains, including two MRSA strains as well as opportunistic pathogen A. baumannii, were encouraging, as low micromolar inhibitory activity was observed for multiple structures. Alkyl chain length on the ammonium group was, as expected, a major determinant of bioactivity. In addition, high therapeutic indexes (up to 125-fold) for triphenyl phosphonium-bearing amphiphiles were observed when comparing antimicrobial activity to mammalian cell lysis activity.

Establishing surface disinfection protocol for micropropagation of clonal apple rootstock MM111

Establishing surface disinfection protocol for micropropagation of clonal apple rootstock MM111

Comparative Analysis of the Disinfection Efficiency of Steel and Polymer Surfaces with Aqueous Solutions of Ozone and Sodium Hypochlorite

Disinfection of surfaces with various functional purposes is a relevant measure for the inactivation of microorganisms and viruses. This procedure is used almost universally, from water treatment facilities to medical institutions and public spaces. Some of the most common disinfectants the World Health Organization recommends are chlorine-containing compounds. Sodium and calcium hypochlorites are only used for disinfection of the internal surfaces of water treatment facilities. However, it is known that ozone is a more powerful oxidizing agent. This study compares the effectiveness of inactivating yeast-like fungi Candida albicans, Gram-positive Bacillus subtilis, and Gram-negative bacteria Escherichia coli with aqueous ozone and sodium hypochlorite solutions. This study used ozone solutions in water with a concentration of 0.5–1.5 mg/L and sodium hypochlorite solutions with an active chlorine concentration of 50–150 mg/L. Steel and polymeric plates were used as substrates. Comparison of the CT (concentration by time) criterion at the ratio of LD50 in NaClO to ozonated water shows that the smallest difference, around 100 times, was observed in the inactivation of Candida albicans. The maximum difference is up to 230 times in the inactivation of Bacillus subtilis.

In vitro germination and micropropagation of the Balkan endemic Lilium chalcedonicum L., a potential ornamental lily

Lilium chalcedonicum L., a bulbous perennial endemic to the Balkans, is recognized for its considerable ornamental potential. In this study, seeds were gathered from a wild population and subjected to surface disinfection. Subsequently, they were placed in Petri dishes containing a half-strength Murashige and Skoog (MS) nutrient substrate (MS/2), with temperature conditions at 15 °C and 20 °C, followed by cycles of 5 °C and return to 15 °C and 20 °C, respectively. The in vitro-cultivated seedlings were then transplanted for further growth in MS medium enriched with either 30 g L-1 or 60 g L-1 sucrose and 0.1 mg L-1 6-N-benzyladenine (BA). In the following stage, the resulting bulblets were separated and cultivated in MS/2, either without hormones (Hf) or with BA at concentrations of 0.2 mg L-1, 0.5 mg L-1, or 1 mg L-1. Moreover, the combined influence of 1-naphthaleneacetic acid (NAA) at a concentration of 1.0 mg L-1 and 0.2 mg L-1 BA was examined. This stage was succeeded by a further division of the bulblets, and the explants were cultured in Hf, MS/2 or with the inclusion of 0.5 mg L-1 BA or a combination of BA and NAA at ratios of 0.2/1 and 0.5/0.05 mg L-1; zeatin at 0.5 mg L-1 was also used, combined with 0.05 mg L-1 NAA. Notably, all seeds exhibited a 100% germination rate following alternating temperature regimes including periods of low temperature. During the initial cultivation phase, each seedling gave rise to two bulblets measuring 0.6 cm in diameter. Subsequent subcultures on Hf substrates and those containing BA without NAA, resulted in the highest number of bulblets (1.6-2.2 bulbs/plant) of the largest diameter (0.8-0.9 cm). Particularly noteworthy was the substantial increase in the average number of produced bulblets during the subsequent subcultures (multiplication stage), where 16.9 bulbs were formed in MS/2 medium containing 0.5 mg L-1 BA, with a median diameter of 1.7 cm.

Improved photocatalytic disinfection performance of graphitic carbon nitride through hybridization with humic acid /zinc peroxide: A synergistic generation of antimicrobial reactive oxygen species

Photocatalytic disinfection of bacteria using photosensitive nanomaterials is an efficient method for bacteria inactivation and is considered a beneficial alternative to chemical disinfectants that produce harmful by-products. However, due to the limited application scope of photocatalysts, the antibacterial efficiency remains unsatisfactory. To enhance the photocatalytic efficiency of the non-metal photosensitizer, graphitic carbon nitride (g-C3N4) nanosheets, they were composited with a metal-based photosensitizer, zinc peroxide (ZnO2) nanoparticles, with the aim of humic acid (HA). Besides the self-generating ability of H2O2 by ZnO2 in an aqueous medium, its deposition over g-C3N4 nanosheets enhances visible light harvesting and increases both surface area and active sites, thereby enhancing photocatalytic efficiency. The resulting composite, g-C3N4/ZnO2, produced more H2O2, •OH, and O2•- radicals than either component when exposed to visible light. Moreover, the photocatalyst demonstrated enhanced photocatalytic disinfection efficacy against Gram-positive bacteria (Staphylococcus aureus and Bacillus subtilis) under dark conditions compared to pure g-C3N4 nanosheets. However, a notably greater antibacterial activity was observed when the nanocomposites were subjected to light irradiation. FESEM images and live-dead assays revealed the physical contact of the nanocomposite with the surface of bacterial cells and the loss of cell membrane integrity. Furthermore, it was observed that there was greater cellular uptake of nanocomposites into cells and the generation of reactive oxygen species (ROS) under light irradiation compared to similar conditions in the dark, leading to an increased photoinactivation rate of bacteria. The enhanced photocatalytic and antibacterial activities of g-C3N4/ZnO2 nanocomposites make them attractive for a range of applications, including use in nanomedicine and environmental surface disinfection.

Visible-light photoactivated proanthocyanidin and kappa-carrageenan coating with anti-adhesive properties against clinically relevant bacteria

The increase of bacterial resistance to antibiotics is a growing concern worldwide and the search for new therapies could cost billions of dollars and countless lives. Inert surfaces are major sources of contamination due to easier adhesion and formation of bacterial biofilms, hindering the disinfection process. Therefore, the objective of this study was to develop a photoactivatable and anti-adhesive kappa-carrageenan coating using proanthocyanidin as a photosensitizer. The complete reduction (>5-log10 CFU/cm3) of culturable cells of Staphylococcus aureus, Escherichia coli and Pseudomonas aeruginosa pathogens was achieved after 30 min of exposure to visible light (420 nm; 30 mW/cm2) with 5 % (w/v) of the photosensitizer. Cell membrane damage was confirmed by measuring potassium leakage, epifluorescence microscopy and bacterial motility analysis. Overall, visible light irradiation on coated solid surfaces mediated by proanthocyanidin showed no cytotoxicity and inactivated clinically important pathogens through the generation of reactive oxygen species, inhibiting bacterial initial adhesion. The developed coating is a promising alternative for a wide range of applications related to surface disinfection and food biopreservation.

UV- C Light Mobile Robotics System

Because diseases are spreading, cleaning enclosed places has become a critical concern. Various methods, including chemical-based solutions in liquid and gas forms, are commonly used for pathogen eradication. However, the environmental damage caused by these methods compounds existing challenges facing humanity. Additionally, UVC light, a promising alternative for disinfection, poses risks to human skin and eyes, necessitating precautions to prevent exposure. Moreover, the effectiveness of UVC disinfection is limited to directly exposed surfaces, rendering it challenging to utilize in occupied spaces where thorough disinfection is crucial. Furthermore, UVC light is less effective on porous surfaces like wood and fabric, further limiting its efficacy. The suggested solution incorporates UVC disinfection technology together with cleaning and drying features to overcome these issues. The objective is to improve the cleaning efficacy and efficiency of enclosed spaces by merging these elements. Both surface disinfection and impurity elimination are the main goals of the mopping and drying functions, which guarantee thorough cleaning. By using clever navigation algorithms to make sure all surfaces have direct exposure to UV-C lamps, the technology also overcomes the shortcomings of existing UVC disinfection. As porous surfaces react less well to UVC disinfection alone, the combination of cleaning and drying activities makes treatment possible. The proposed study provides a brief review of the methods used in sanitation with and without UV rays and the specific range of UV rays utilized in sanitation. It suggests an innovative UV-C sanitation robotic system that overcomes the shortcomings of existing UV-C disinfection systems.