Discharge Power Research Articles

Scaling to practical pouch cell supercapacitor: Electrodes by electrophoretic deposition

The scale-up of supercapacitors by electrophoretic deposition (EPD) from coin cell to pouch cell with commercially relevant mass loadings and thicknesses is reported. The use of EPD in electrode fabrication mainly reduces the interfacial resistance and increases the mechanical flexibility of the electrodes. The cycling performance or conversion efficiency can also be improved due to the highly porous EPD coatings. An exemplary investigation of activated carbon (AC) electrodes with an electrolyte comprising of tetraethylammonium tetrafluoroborate in acetonitrile is carried out. According to the general literature, EPD of AC on metal substrates has not performed well for supercapacitor electrodes unless they were thinner and with lower mass loadings than commercial requirements. As a consequence, and to redress this research gap, all the electrodes prepared in this work demonstrate high mass loadings (8 mg cm−2) and practical layer thicknesses (125 µm) and contain polyvinylidene fluoride binders with electrically conductive carbon black particles. Research investigations include: (a) impact of EPD of AC onto small (10 cm2) and large areas (50 cm2) of aluminum foil current collectors, (b) scaling-up of coin to pouch cells, and (c) the preparation of electrode coatings on both sides of the current collector for the first time using EPD for pouch cell investigations. Our research learning shows the evidence of practical cell performance, including current loading (40 A g−1), tens of thousands of successive charge and discharge operation (150,000 cycles), power (30 kW kg−1) and energy densities (10 W h kg−1), capacitance (154 F g−1), capacitance retention (80%) and coulombic efficiency (relatively close to 100%). Based upon the success of the pouch cells investigated in this work, further research studies on the use of EPD for preparing energy storage electrodes for commercial cylindrical types of supercapacitors is envisaged.

Recent Progress Using Graphene Oxide and Its Composites for Supercapacitor Applications: A Review

Supercapacitors are prospective energy storage devices for electronic devices due to their high power density, rapid charging and discharging, and extended cycle life. Materials with limited conductivity could have low charge-transfer ions, low rate capability, and low cycle stability, resulting in poor electrochemical performance. Enhancement of the device’s functionality can be achieved by controlling and designing the electrode materials. Graphene oxide (GO) has emerged as a promising material for the fabrication of supercapacitor devices on account of its remarkable physiochemical characteristics. The mechanical strength, surface area, and conductivity of GO are all quite excellent. These characteristics make it a promising material for use as electrodes, as they allow for the rapid storage and release of charges. To enhance the overall electrochemical performance, including conductivity, specific capacitance (Cs), cyclic stability, and capacitance retention, researchers concentrated their efforts on composite materials containing GO. Therefore, this review discusses the structural, morphological, and surface area characteristics of GO in composites with metal oxides, metal sulfides, metal chalcogenides, layered double hydroxides, metal–organic frameworks, and MXene for supercapacitor application. Furthermore, the organic and bacterial functionalization of GO is discussed. The electrochemical properties of GO and its composite structures are discussed according to the performance of three- and two-electrode systems. Finally, this review compares the performance of several composite types of GO to identify which is ideal. The development of these composite devices holds potential for use in energy storage applications. Because GO-modified materials embrace both electric double-layer capacitive and pseudocapacitive mechanisms, they often perform better than pristine by offering increased surface area, conductivity, and high rate capability. Additionally, the density functional theory (DFT) of GO-based electrode materials with geometrical structures and their characteristics for supercapacitors are addressed.

Effects of chemically-reductive trace gas contaminants on non-thermal plasma inactivation of an airborne virus

Transmission of airborne infectious diseases poses great risk for public health and socio-economic stability, thus, there is a need for an effective control method targeting the spread and transmission of pathogenic aerosols. The existence of chemically-reductive trace air contaminants in animal agriculture may affect the oxidation inactivation process of pathogens. In this study, we report how the presence of such gasses impacts the effectiveness of using non-thermal plasma (NTP) within a packed-bed dielectric barrier discharge reactor to inactivate MS2 bacteriophage. Inactivation of the aerosolized bacteriophage is determined by the combination of viability and polymerase chain reaction assays. Using a plasma power source with a voltage of 20 kV and frequency of 350 Hz, after differentiating and excluding the physical removal effects of viral aerosols potentially caused by plasma, the baseline inactivation of MS2 aerosol in air has been determined based on an overall air flow rate of 200 Liters per minute and plasma discharge power of 1.8 W. When either ammonia or hydrogen sulfide gas is introduced into the airstream at a concentration of 1 part per million, the NTP virus inactivation efficiency is reduced to around 0.5-log from the 1-log baseline inactivation in air alone. Higher concentrations of those gasses will not further inhibit the effectiveness of plasma inactivation.

A Feature Extraction Method for Prognostic Health Assessment of Gas Compressor Valves

Abstract This paper presents features derived from the pressure-volume (PV) diagram that is useful in estimating different valve faults in reciprocating compressors with a strong potential of remaining useful life prediction. The PV diagram is expected to deviate depending on valve wear conditions. The valve degradation types explored in this work are leakage, seat wear, and spring fatigue in the suction and discharge assemblies of a Dresser-Rand ESH-1 compressor commonly used in the petrochemical industry. The proposed method estimates the polytropic exponent on the compression and expansion phase as well as the discharge and suction valve loss power and uses them as features for a quadratic discriminant analysis. The features are created through in-cylinder pressure, suction pressure, discharge pressure, and crank angle measurements collected on a single-stage, dual-acting compressor operating on air with wear precisely machined and seeded into the poppets of the inlet and outlet valves. A very high classification accuracy is achieved in distinguishing the wear types, severity, and location with strong prognostic trends.

Pea protein-inulin conjugate prepared by atmospheric pressure plasma jet combined with glycosylation: structure and emulsifying properties.

Pea protein is one of plant proteins with high nutritional value, but its lower solubility and poor emulsifying properties limit its application in food industry. Based on wet-heating glycosylation of pea protein and inulin, effects of discharge power of atmospheric pressure plasma jet (APPJ) on structure, solubility, and emulsifying ability of pea protein-inulin glycosylation conjugate were explored. Results indicated that the APPJ discharge power did not affect the primary structure of pea protein. However, changes in secondary and spatial structure of pea protein were observed. When APPJ discharge power was 600 W, the solubility of glycosylation conjugate was 75.0% and the emulsifying stability index was 98.9 min, which increased by 14.85 and 21.95% than that of only glycosylation sample, respectively. These findings could provide technical support for APPJ treatment combination with glycosylation to enhance the physicochemical properties of plant-based proteins.

Experimental and Theoretical Assessment of Inverter-Operated Split Air Conditioner with Low GWP Alternative Refrigerants

This article presents experimental evaluation and comparative analysis of low GWP alternative refrigerants, namely HC-290 (propane), HC-1270 (propylene), HC/HC-1270 blend, and HFC-32 (difluoro methane) as drop-in replacements for HCFC-22 (Chloro difluoro methane) in a typical 1.5 TR capacity inverter operated split type air conditioner (SAC). The experimental setup consisted of retrofitting an original HCFC-22 test unit following the soft optimization of the SAC system for each alternative refrigerant, followed by testing under controlled operating conditions as per the IS 1391, Part-1 standard at the half capacity and the rated capacity of inverter SAC. The results obtained were compared against the baseline HCFC-22 test unit. The optimized SAC gave EERIS (Indian Seasonal Energy Efficiency Ratio) of 4.63 for HC-290, 4.71 for HC-1270 and 4.87 for HC-290/HC-1270 blend, respectively increased by 8.94 %, 10.82 % and 14.58 % compared to HCFC-22. HFC-32 delivered the maximum cooling capacity of 6.78 kW, 3.67 % higher than baseline unit at the rated capacity. HC-290/HC-1270 blend exhibited the lowest power consumption and discharge temperature amongst all the refrigerants considered. The charge of flammable refrigerants has been optimized below LFL satisfying EN378 standard for the safety of inverter SAC in domestic applications.

Superhydrophobic Co/Fe sulfide nanoparticles and single-atoms doped carbon nanosheets composite air cathode for high-performance zinc-air batteries

Development of a high-performance bifunctional catalyst is essential for the actual implementation of zinc-air batteries in practical applications. Herein, a bifunctional cathode of Co3S4/FeS heterogeneous nanoparticles embedded in Co/Fe single-atom-loaded nitrogen-doped carbon nanosheets is designed. Cobalt-iron sulfides and single atomic sites with Co-N4/Fe-N4 configurations are confirmed to coexist on the carbon matrix by EXAFS spectroscopy. 3D self-supported super-hydrophobic multiphase composite cathode provides abundant active sites and facilitates gas–liquid-solid three-phase interface reactions, resulting in excellent electrocatalytic activity and batteries performance, i.e., an OER overpotential (η10) of 260 mV, a half-wave potential (E1/2) of 0.872 V for ORR, a ΔE of 0.618 V, and a discharge power density of 170 mW cm−2, a specific capacity of 816.3 mAh g−1. DFT analysis shows multiphase coupling of sulfide heterojunction through single-atomic metal doped carbon nanosheets reduces offset on center of electronic density of states before and after oxygen adsorption, and spin density of adsorbed oxygen with same spin orientation, leading to weakened charge/spin interactions between adsorbed oxygen and substrate, and a lowered oxygen adsorption energy to accelerate OER/ORR.

Argon admixture-driven enhanced ionization and performance of a 5 kW Hall thruster on krypton

Utilizing alternative propellants has been recognized as a strategy to reduce the total cost of propellants in electric propulsion-based missions. The aim of this study is to quantify the Hall effect thruster (HET) performance and operating characteristics using a Kr–Ar mixture to enable mission designers to evaluate the impact on mission and spacecraft design. We present the performance and plume plasma properties of the P5 5 kW-class HET operated with a Kr–Ar mixture with Ar volumetric flow rate fractions from 0 to 100%. The thruster is characterized at discharge power levels of 2.6 kW and 4.1 kW at constant discharge current and voltage over the range of Ar fractions. Despite higher ionization energy and lower mass of Ar, the thruster exhibited a similar level of thrust within 2% when comparing the pure Kr and 26%-Ar mixture cases. The derived ion energy distribution functions and analytical modeling suggest that the characteristic length for the ionization region is extended as the Ar fraction increases. The increased residence time of Kr at the extended ionization region and background energetic electrons from the ionized Ar neutrals are considered to cause this enhanced ionization of the injected Kr neutrals. This leads to a 6% higher Kr ion density at the 26%-Ar case even at the 16% less injected Kr neutral density than in the pure Kr case. The enhanced Kr ionization and generated Ar ions in the 26%-Ar case consequently led to a comparable thrust with that of the pure Kr case. The study indicates that mixing Ar with approximately 26% volumetrically with Kr can provide a similar or even higher thrust performance at the same discharge power. This will be particularly advantageous for various space missions that require high impulses by reducing the total cost of the propellant.

Oxygen Vacancy-Rich NiCo2O4 on Carbon Framework with Controlled Pore Architectures as Efficient Bifunctional Electrocatalysts for Zn-Air Batteries

Transition metal oxides are considered alternative electrocatalysts for ZAB owing to their multiple oxidation states. However, they have limitations such as low electrical conductivity and the deficiency of reactive sites. In this study, to overcome these shortcomings and improve electrocatalytic activity, oxygen vacancies and porous architectures were introduced through a partial reduction process and a porous carbon framework. Open porous carbon microspheres with uniformly loaded NiCo2O4 nanosheets and oxygen vacancies (V-NCO/OPC) displayed enhanced electrocatalytic performance with a low Tafel slope (68 mV dec-1) in the oxygen reduction reaction (ORR) and a low overpotential (402 mV) at 10 mA cm–2 in the oxygen evolution reaction (OER). The combined effect of the oxygen vacancies and porous architecture can offer sufficient active sites, modify the electronic structure of the metal oxide surface, and facilitate mass transport, enhancing the electrocatalytic properties of V-NCO/OPC. Furthermore, when applied for ZAB, V-NCO/OPC demonstrated better electrochemical performance including discharge power density (154.9 mW cm-2) at the current density of 175.9 mA cm-2, low voltage gap (0.85 V) at the initial cycle, and long-term (250 h) cycle stability at the current density of 10 mA cm−2 than those of noble-metal electrocatalysts.

Preparation of palladium-based catalyst by plasma-assisted atomic layer deposition and its applications in CO2 hydrogenation reduction

Supported Pd catalyst is an important noble metal material in recent years due to its high catalytic performance in CO2 hydrogenation. A fluidized-bed plasma assisted atomic layer deposition (FP-ALD) process is reported to fabricate Pd nanoparticle catalyst over γ-Al2O3 or Fe2O3/γ-Al2O3 support, using palladium hexafluoroacetylacetonate as the Pd precursor and H2 plasma as counter-reactant. Scanning transmission electron microscopy exhibits that high-density Pd nanoparticles are uniformly dispersed over Fe2O3/γ-Al2O3 support with an average diameter of 4.4 nm. The deposited Pd-Fe2O3/γ-Al2O3 shows excellent catalytic performance for CO2 hydrogenation in a dielectric barrier discharge reactor. Under a typical condition of H2 to CO2 ratio of 4 in the feed gas, the discharge power of 19.6 W, and gas hourly space velocity of 10000 h−1, the conversion of CO2 is as high as 16.3% with CH3OH and CH4 selectivities of 26.5% and 3.9%, respectively.

Effect of process parameters on plasma partial oxidation approach for removal of leaking LPG

In order to address the challenge of preventing explosions in the accidental disposal of leaking liquefied petroleum gas (LPG), a plasma partial oxidation (PPO) approach for converting the gas into liquid products is proposed for the first time, which eliminates the explosion risk in leaking LPG from the pathway of combustible gas removal. The effect of the initial C4H10 (Simulated LPG) concentration, discharge power, and residence time on the reaction performance were investigated, and the main reaction pathway was proposed. The residence time had the greatest effect on C4H10 conversion (27.6 – 78.0%) and yield of total liquid products (26.0 – 63.9%). The rise in discharge power substantially increased the C4H10 conversion (29.9 – 51.2%) and maintained a liquid product selectivity of more than 88.0%. When the initial C4H10 concentration is lower than 5%, the C4H10 concentration can reduce directly to 1.8% at a moderate discharge power (39 W) and residence time (0.81 s), which can eliminate the risk of explosion. This article provides a new approach for the disposal of LPG spills and offers new insights into the effects of main process parameters and their mechanisms for optimizing the PPO reaction performance of converting C4H10 into liquid products.

Analysis of discharge performance and thermo-electric conversion efficiency in thermally regenerative ammonia-based flow battery with foam copper electrode

This paper established a numerical model of mass transport and electrochemical reaction coupling in porous media of thermally regenerative ammonia-based flow battery with foam copper electrode (TRAFB-FCE) for the first time. The effects of the structural parameters of the foam copper electrode on the power density, energy density, discharge capacity, and active species distribution of the battery were comprehensively studied based on the coupled numerical model. Special attention was paid to the selection strategy of the initial reactant concentration for the battery under different discharge conditions. The results suggest that increasing the porosity or thickness of the foam copper electrode causes the voltage and power density of the battery to first increase and then decrease, while the discharge capacity and energy density monotonically increase. Moreover, the battery should avoid discharging at current densities exceeding 720 A·m−2. When the discharge current density is less than 200 A·m−2, it is preferable to set the initial concentration of Cu2+ to 0.4 mol/L, while the discharge current density is in the range of 200–720 A·m−2, the initial concentration of Cu2+ is preferable to be 0.3 mol/L. When it discharges at about 5 % of its maximum power density, the Carnot-relative efficiency of this battery is comparable to the highest value currently reported in the field of liquid-based thermo-electric conversion achieved by the Thermal Regenerative Electrochemical Cycle (TREC) technology, and the power density of the former is 8.87 times that of the latter.

Antibiotic Chloramphenicol degradation using submerged thermal plasma synergized with LaMnO3 catalyst

The present study focused on the degradation of antibiotic Chloramphenicol (CAP), an emerging contaminant, using submerged thermal plasma (STP) technology. Almost 99 % degradation and 82 % mineralization were achieved within 20 min of treatment by Ar/CO2 plasma, generated at 6.2 kW discharge power using a customized thermal plasma torch inside the aqueous solution. Kinetic analysis revealed first-order reaction for CAP degradation with a rate constant of 0.257 min−1. Long-lived species, such as H2O2, O3, NO2–, NO3–, and Cl- formed during plasma treatment were quantified. LaMnO3 perovskite (LMO) nanopowder prepared through a novel thermal plasma route, was introduced as catalyst into the treatment system which enhanced the degradation and mineralization efficiency by 34 % and 17 %, respectively, showing a strong synergetic effect between STP and catalyst. The energy yield was elevated from 102 mg/kWh to 144 mg/kWh with the addition of catalyst into the STP treatment system. Liquid chromatography-mass spectroscopy was used to identify the various degradation intermediates produced during thermal plasma treatment and correspondingly possible degradation pathways were proposed. The antibacterial activity assessment results revealed a significant reduction in the antimicrobial activity of all treated solutions against Gram-positive Bacillus cereus and Gram-negative Pseudomonas aeruginosa bacteria. Additionally, seed germination and growth assessment revealed a reduction in phytotoxicity of the treated solutions. STP, combined with the LMO, proved highly effective in treating pharmaceutical contamination in aqueous medium.

Coordinated power management strategy for reliable hybridization of multi-source systems using hybrid MPPT algorithms

This research discusses the solar and wind sourcesintegration in aremote location using hybrid power optimization approaches and a multi energy storage system with batteries and supercapacitors. The controllers in PV and wind turbine systems are used to efficiently operate maximum power point tracking (MPPT) algorithms, optimizing the overall system performance while minimizing stress on energy storage components. More specifically, on PV generator, the provided method integrating the Perturb & Observe (P&O) and Fuzzy Logic Control (FLC) methods. Meanwhile, for the wind turbine, the proposed approach combines the P&O and FLC methods. These hybrid MPPT strategies for photovoltaic (PV) and wind turbine aim to optimize its operation, taking advantage of the complementary features of the two methods. While the primary aim of these hybrid MPPT strategies is to optimize both PV and wind turbine, therefore minimizing stress on the storage system, they also aim to efficiently supply electricity to the load. For storage, in this isolated renewable energy system, batteries play a crucial role due to several specific benefits and reasons. Unfortunately, their energy density is still relatively lower compared to some other forms of energy storage. Moreover, they have a limited number of charge–discharge cycles before their capacity degrades significantly. Supercapacitors (SCs) provide significant advantages in certain applications, particularly those that need significant power density, quick charging and discharging, and long cycle life. However, their limitations, such as lower energy density and specific voltage requirements, make them most effective when combined with other storage technologies, as batteries. Furthermore, their advantages are enhanced, result a more dependable and cost-effective hybrid energy storage system (HESS). The paper introduces a novel algorithm for power management designed for an efficient control. Moreover, it focuses on managing storage systems to keep their state of charge (SOC) within defined range. The algorithm is simple and effective. Furthermore, it ensures the longevity of batteries and SCs while maximizing their performance. The results reveal that the suggested method successfully keeps the limits batteries and SCs state of charge (SOC). To show the significance of system design choices and the impact on the battery’s SOC, which is crucial for the longevity and overall performance of the energy storage components, a comparison in of two systems have been made. A classical system with one storage (PV/wind turbine/batteries) and the proposed system with HESS (PV/wind turbine system with batteries). The results show that the suggested scenario investigated with both wind and solar resources appears to be the optimum solution for areas where the two resources are both significant and complementary. The balance between the two resources seems to contribute to less stress on storage components, potentially leading to a longer lifespan. An economical study has been made, using the Homer Pro software, to show the feasibility of the proposed system in the studied area.

Research on SOP Estimation Based on SOC Constraints under Static Operating Conditions

In a battery management system (BMS), accurate estimation of system operating power (SOP) is essential to ensure battery performance and extend service life. In this paper, an SOP estimation method based on open circuit voltage (OCV), state of charge (SOC) and battery current is studied. By analyzing the battery data under dynamic stress test (DST) conditions, the estimated value of continuous peak charge and discharge current is calculated, and the corresponding continuous peak charge and discharge power is estimated accordingly. Comparing the estimated charging and discharging power with the experimental value, the results show that the new algorithm can significantly improve the estimation accuracy of SOP. It not only improves the accuracy of SOP estimates, but also helps to optimize BMS, thereby improving the overall performance and service life of the power battery.

Air disinfection by nanosecond pulsed DBD plasma

Atmospheric pressure dielectric barrier discharge (DBD) plasma is an emerging and promising technique for air disinfection in public environments. Power supply is a crucial factor but it remains unclear about its impacts on the air disinfection performance of plasmas. In this work, a nanosecond (ns) pulsed power supply was applied to drive an in-duct grating-like DBD array to achieve fast single-pass air disinfection. The influence of pulse parameters and environmental factors on both the discharge characteristics and the single-pass bacterial inactivation efficiency were uncovered. At a close relative humidity (RH) level, the efficiency was dominated by the discharge power, namely, specific input energy could serve as the disinfection dose. A higher frequency, shorter pulse rising time, and suitable pulse width are preferred to obtain a higher Z value. The pulsed source was not notably superior to an alternating current source, or even worse at a low voltage frequency at the same discharge power. Airflow humidity was a predominant factor to improve the efficiency and a single-pass efficiency of ∼ 99% and a Z value of 2.2 L/J were achieved under an optimal RH of 50%–60%. This work provides fundamental knowledge of ns-pulsed DBD on discharge characteristics and air disinfection behaviors.

Effect of atmospheric pressure plasma jet on the structure and physicochemical properties of wheat starch.

The effect of atmospheric pressure plasma jet (APPJ) with different discharge power (0, 400, 600, and 800 W) on the structure and physicochemical properties of wheat starch were evaluated in this study. After APPJ treatments, significant declines in peak viscosity, breakdown viscosity, and final viscosity of wheat starch pasting parameters were observed with increase of plasma treatment power. Being treated with discharge power of 800 W, the PV and BD value of wheat starch paste significantly dropped to 2,578 and 331 cP, respectively. Apparently, APPJ could raise the solubility of wheat starch, while reduce the swelling capacity, and also lower the G' and G″ value of wheat starch gel. Roughness and apparent scratch was observed on the surface of the treated wheat starch granules. Although APPJ treatment did not alter wheat starch's crystallization type, it abated the relative crystallinity. APPJ treatment might be useful in producing modified wheat starch with lower viscosity and higher solubility.

Plasma Technology Applied to Improve Wettability for Emerging Mycelium-Based Materials

Plasma technology is increasing its applications in the textile industry for conferring surface functionalities through greener processes. In this study, plasma treatments are studied to improve the wettability of mycelium-based material, an emerging material with a lot of potential in the near future. The plasma effect was characterized by assessing the added functionality (wettability) and inspecting surface modifications with different techniques, such as scanning electron microscopy (SEM) and X-Ray photoelectron spectroscopy (XPS). Low pressure plasma (LPP) treatments were successfully applied into the mycelium-based material and optimal power of discharge and treatment time were set for this material (750 W, 17.5 min). With the optimized LPP treatments, the water absorption capacity of mycelium-based material was improved by 2000% and some surface morphological modifications were observed by SEM analysis. On the other hand, XPS analysis demonstrated how the plasma treatment changes the surface composition.

Analysis of the effect of high falling water on the performance of hydroelectric power plants using whirpool type turbines

A hydroelectric power plant (PLTA) uses the flow of water as a source of energy. Evaluating the output of hydropower facilities, including the optimal height of the waterfall, turbine torque, electrical power, generator power, and generated efficiency, was the aim of the study. This study intends to investigate the power, torque, and efficiency that may be produced by a hydroelectric power plant with a whirlpool-type turbine, as well as how the height of falling water influences the operation of the plant. The experiment in this study measures three different waterfall heights with five different blade configurations. The study on the hydropower prototype involved three trials that collected data on torque, power, efficiency, waterfall height, and water discharge. The PLTA Prototype's best potential head in Test 3 was determined to be 0.01143, with a height of 0.67 meters, no sluice, and a diameter of 0.0625 meters. The lowest water outflow was discovered at a head of 0.55 meters with a water debit of 0.01036. The third attempt, which featured a sluice opening with a diameter of 0.0625 meters and a height of 0.67 meters (head), used the most water power in the experiment. The testing yielded the following results: 75.13 watts of water power, 5.16 watts of generator power, 0.233 N.m. of torque, 2.63 watts of turbine power with a generator load 3.73 watts without one, and 6.87% efficiency. Data gathered from the hydropower prototype's operation can be used to construct testing instruments for use in laboratories

Determining the effect of laboratory testing conditions on working parameters of the ST-25 hall thruster

The object of this study is the ST-25 Hall thruster with limited discharge power, no more than 200 W, designed by Flight Control LLC (Ukraine). The problem that was solved in the current paper was to determine the effect of residual gas pressure in vacuum chambers on the operating parameters of the Hall thruster. To solve this task, the operating parameters of the ST-25 thruster were determined, which was tested in three vacuum chambers with different sizes of residual pressure. As a result of the laboratory study into the operating parameters of the ST-25 thruster, the volt-ampere characteristics of the engine discharge at fixed values of the working gas (xenon) flow rate were obtained. The dependences of the engine thrust on the mass flow rate of the working gas at fixed values of the discharge voltage were derived. Based on the experimental data, the dependences of the specific impulse of the engine anode unit on the discharge voltage, as well as the dependence of efficiency of the engine anode unit on the discharge voltage were calculated. The studies showed that when the residual pressure in the vacuum chamber is reduced by 2–3 times, the operating parameters of the engine increase by 15–20 %. Such a reduction in residual pressure increases thrust by 25–40 %. Special feature of the results is the determination of threshold values of residual gas pressure in vacuum chambers during experimental studies, in which the operating parameters of the Hall thruster are similar to its operating parameters under space conditions. This work’s findings could be used in practice when conducting experimental studies of electric rocket engines, when it is necessary to estimate the operating parameters of Hall thrusters that will be obtained under actual space conditions