Discharge Efficiency Research Articles

Design and preparation of ternary polymer nanocomposites for high energy density film capacitors

High discharge energy density (Ue) film capacitors are important for miniaturization and integration in power electronic applications. The Ue of a polymer film is mainly dependent on Weibull's breakdown strength (Eb) and dielectric constant (εr). This work aims to develop ternary nanocomposites composed of polycarbonate (PC), Al2O3 nanoparticles (Al2O3 NPs) and BaTiO3 nanowires (BT NWs) for capacitive energy-storage. Al2O3 NPs have a wide bandgap and are expected to enhance Eb owing to their insulating nature, while BaTiO3 nanowires (BT NWs) are ferroelectric and are expected to provide a high εr. To overcome local electric-field distortion at the interface due to the mismatch in εr, core-shell structured BT@SiO2 NWs are prepared. The Eb of the composite containing 1.0 wt% Al2O3 NPs and 6.0 wt% BT@SiO2 NWs can reach 626 MV/m while that of the pure PC is 465 MV/m. As a result, its Ue reaches 12.12 J/cm3, which is improved by 211% that of the pure PC. Its discharge efficiency is 83.5%. A finite element analysis corroborates the superiority of the ternary polymer nanocomposites for dielectric energy-storage.

Investment-based optimisation of energy storage design parameters in a grid-connected hybrid renewable energy system

Grid-connected hybrid renewable power systems with energy storage can reduce the intermittency of renewable power supply. However, emerging energy storage technologies need improvement to compete with lithium-ion batteries and reduce the cost of energy. Identifying and optimising the most valuable improvement path of these technologies is challenging due to the non-linearity of the energy system model when considering parameters as independent variables. To overcome this challenge, a novel investment-based optimisation method is proposed. The method involves linear optimisation of the hybrid renewable energy system and subsequent investment optimisation, accounting for diminishing improvements per investment. The results from applying the investment-based optimisation to thermal energy, pumped thermal energy, molten salt, and adiabatic compressed air energy storage technologies, show that improving the discharge efficiency is the most valuable for all technologies. The second most important parameters are the costs of discharge capacity and energy storage capacity, and the least important parameters are the charge capacity cost and charge efficiency. The study provides detailed improvement pathways for each technology under various operational conditions, assisting developers in resource allocation. Overall, the investment-based optimisation method and findings contribute to enhancing the competitiveness of emerging energy storage technologies and reducing reliance on batteries in renewable energy systems.

How sintering temperature affects the electrochemical performance of ultra-high nickel (Ni > 0.9) cathode material

The burgeoning demand for electric vehicles with extended driving ranges has propelled ongoing development efforts for ultra-high nickel (Ni > 0.9) cathode materials. Despite significant ongoing research focused on Ni-rich cathode materials, a more comprehensive foundational understanding of ultra-high nickel cathode materials is essential. In our research, we employed LiNi0.94Co0.06O2 as a model ultra-high nickel cathode material to systematically delve into the interplay between sintering temperature, structural features, and electrochemical behavior. Within a sintering temperature spectrum of 660–720 °C, we discerned that specimens produced at diminished temperatures manifest a reduced initial discharge capacity yet excel in cycling endurance. In stark contrast, their counterparts produced at augmented temperatures behave inversely. Identifying a singular sintering temperature that achieves equilibrium between initial discharge capacity and cycling performance proves elusive. Through X-ray diffraction and high-resolution transmission electron microscopy, it became evident that samples synthesized at lower temperatures exhibit pronounced lithium-nickel mixing and develop a thicker NiO layer on the surface, leading to compromised initial discharge performance and capacity. Utilizing focused ion beam scanning electron microscopy, differential capacity analysis, and in-situ X-ray diffraction, we confirm that samples synthesized at lower temperatures possess smaller particle sizes, enabling them to withstand volumetric expansion stress during cycling, resulting in enhanced cycling performance. In the realm of ultra-high nickel cathode materials, elevating the sintering temperature is a conduit to superior initial discharge efficiency and capacity. Yet, the imperative of preserving diminutive particle dimensions, as a stratagem to bolster cycling performance, stands out as a pivotal research frontier.

Improved Capacitive Energy Storage at High Temperature via Constructing Physical Cross‐Link and Electron–Hole Pairs Based on P‐Type Semiconductive Polymer Filler

AbstractIn this work, p‐type polymer semiconductor poly(2‐((3,6,7,10,11‐pentakis (hexyloxy) triphenylene‐2‐yl)oxy)ethyl methacrylate) (PMHT) is added into polyetherimide (PEI). Benefiting from the electrostatic interaction between strong electrophilic charged phenyls of the PEI matrix and strong electronegative benzophenanthrene unit of the PMHT filler, the physical cross‐linked networks are formed in polymer blends. Meanwhile, the lowest unoccupied molecular orbital level of PEI is close to the highest occupied molecular orbital level of PMHT, which is easy to establish electron–hole pair by Coulomb force. Thus, the carrier trap is constructed in the heterojunction region between PMHT filler and PEI matrix. Both physically cross‐linked networks and electron–hole pairs can promote breakdown strength (Eb) of PEI and decrease energy loss. Importantly, PMHT filler can improve the dielectric constant of PEI. As a result, 0.75 wt% PMHT/PEI delivers an ultrahigh discharge energy density (Ud) of 10.7 J cm−3 at an Eb of 680 MV m−1 and at room temperature, and maintains a charge and discharge efficiency of above 90%. In addition, a superior Ud of 5.1 and 3.3 J cm−3 is achieved at 150 and 200 °C, respectively. This paper creates a new perspective for preparing high‐properties polymer dielectrics by combining the advantages of cross‐linking and electron–hole pairs.

Study on improving liquid carrying performance of annular jet pump gas well with static mixer

AbstractIn the process of natural gas extraction, the phenomenon of liquid loading will affect the efficiency of gas well extraction and reduce the life of the well. Compared with conventional drainage gas extraction technology, the jet pump can not only reduce the bottom back pressure and ensure the stable production of gas reservoirs but also promote the final recovery rate. Since the jet pump relies on the interaction between fluid particles to transfer energy, the energy loss is large and the efficiency is low. To maximize the advantages of the gas‐driven jet pump, this study innovatively combines a static mixer with an annular jet pump. Utilizing the cyclonic effect produced by the static mixer, the original gas‐liquid axial motion is transformed into a stronger vortex motion, and the liquid droplets are changed into a liquid film that is easier to carry, which significantly improves the discharge efficiency of the jet pump. This study uses a combination of numerical simulation and experimental analysis to compare the associated effects of the new annular jet pump (NAJP) and the conventional annular jet pump (CAJP) on the liquid‐carrying performance of gas wells in terms of cyclonic effect, droplet breakage ratio, and pump efficiency. The results show that, compared with CAJP, NAJP increases the mass flow rate of the sucked fluid. The droplet breakage ratio increases by 15.4% year‐on‐year, while the critical liquid‐carrying flow rate is reduced by about 10.7%, resulting in a maximum pumping efficiency of 37%, an increase of about 30.7% year‐on‐year. At the same time, the reduction of the energy coefficient means lower energy consumption. In summary, NAJP is better than CAJP in terms of liquid‐carrying effect and efficiency.

Microwave assisted synthesis for ϵ-MnO2 nanostructures on Ni foam as for rechargeable Li–O2 battery applications

Lithium-air batteries exhibits high practical energy densities ranging from 1000 to 4000 Wh Kg−1, rendering them appealing for applications in portable electronic devices and electric vehicles. Nevertheless, they grapple with challenges like low charge–discharge efficiency, limited stability over multiple cycles, and electrode degradation stemming from undesirable side reactions, thus impeding their commercial market. In this study, ϵ-MnO2 petal-like nanostructures were synthesized on Ni foam via simple, microwave-assisted synthesis approach. The resulting ϵ-MnO2/Ni electrode demonstrated storage capacities (1982 mAh g−1 discharge capacity at 200 mA g−1) alongside enhanced cyclability and stability over 100 cycles, independent of discharge depth. This electrochemical performance can be attributed to its 3D morphology, oxygen defects, and the absence of side reactions from carbon-based additives. Overall, ϵ-MnO2/Ni electrode catalysts hold potential for realizing cost-effective Li-O2 based energy storage technologies.

Principle and applications of quantum dots in zinc battery

With the advent of quantum dots, it has been widely used to various fields of material science to enhance the performance. This study focuses on the potential of graphene quantum dots (GQDs) to improve the performance of zinc batteries. Due to its unique photoelectric properties, high surface area and excellent conductivity, GQDs shows significant application potential in the field of battery technology. This article mainly discusses the possibility of using GQDs to improve the charge and discharge efficiency of zinc batteries, including how to improve the conductivity of the electrode, provide more active sites, and increase the energy storage capacity of the battery. The paper also identifies key challenges and limitations in this area, including the material complexity of GQDs, scalability issues, impact on battery stability, and environmental impact. Finally, the article provides some ideas on how to address these challenges and the future of GQDs applications in zinc batteries.

A Fully Elastic Wearable Electrochemical Sweat Detection System of Tree-Bionic Microfluidic Structure for Real-Time Monitoring.

Fresh sweat contains a diverse range of physiological indicators that can effectively reflect changes in the body. However, existing wearable sweat detection systems face challenges in efficiently collecting and detecting fresh sweat in real-time. Additionally, they often lack the necessary deformation capabilities, resulting in discomfort for the wearer. Here, a fully elastic wearable electrochemical sweat detection system is developed that integrates a sweat-collecting microfluidic chip, a multi-parameter electrochemical sensor, a micro-heater, and a sweat detection elastic circuit board system. The unique tree-bionic structure of the microfluidic chip significantly enhances the efficiency of fresh sweat collection and discharge, enabling real-time detection by the electrochemical sensors. The sweat multi-parameter electrochemical sensor offers high-precision and high-sensitivity measurements of sodium ions, potassium ions, lactate, and glucose. The electronic system is built on an elastic circuit board that matches perfectly to wrinkled skin, ensuring improved wearing comfort and enabling multi-channel data sampling, processing, and wireless transmission. This state-of-the-art system represents a significant advancement in the field of elastic wearable sweat detection and holds promising potential for extending its capabilities to the detection of other sweat markers or various wearable applications.

CFD Numerical Simulation Study Based on Plunger Air Lift

To study the movement law of a plunger air lift and liquid discharge efficiency, this paper observes the plunger movement and leakage through indoor experiments, based on which the CFD method is applied to establish a numerical model with the same experimental conditions, and compares the simulation results with the experiments, verifies the feasibility of the CFD simulation, and optimizes the structure of the plunger, and researches the change rule of the bottom-hole pressure and the wellhead pressure in a 200 m long wellbore. The results show that the error between CFD simulation and experimental data is 12.5%. When the depth of the plunger groove is 10 mm, the width of each groove is 10 mm, and the number of grooves is 12, the leakage is minimal; in addition, to ensure the smooth lifting of the plunger, it is necessary to control the wellhead pressure and keep the pressure difference with the bottom of the well. When the wellbore pressure is 10 MPa, the wellhead pressure should be no more than 7 MPa, and when the wellbore–wellhead pressure difference is kept at a certain level (7 MP), the plunger cannot continue to move up when the wellhead pressure is more than 18 MP, so it is necessary to control the wellbore pressure as it cannot be too big and increase the wellbore–wellhead pressure difference as much as possible. The above study of the plunger lifting law provides a reference basis for the determination of the above research plunger process parameters.

Investigation on the unsteady ventilation performance of oscillating jet air supply through both spontaneous vortex street effect and active modulation

Ventilation is one of the most vital measures to create a healthy and comfortable indoor environment, significantly influencing indoor air quality and building energy consumption. The conventional steady-state airflow field of a ventilated room, if not reasonably configured, is prone to cause air stagnation in certain regions, whereas the unsteady airflow improves the mixing effect, which favors the dispersion and purging of indoor air pollutants. This paper proposes a method to induce an unstable air flow field utilizing the spontaneous Karman vortex street effect on the air-supply jet and swinging modulation. The quasi-periodicity of the airflow field and its influence on the indoor pollutant purging effect were investigated. The effects of air velocity oscillation and pollutant concentration decay in a ventilated room were studied through experimental measurements and computational fluid dynamics analysis. The results show that the transverse oscillation jet has a dominant period of 1.6 s and the longitudinal oscillation jet has a dominant period of 2.987 s, and both jets have a width about twice that of the free jet. The airborne pollutant discharge efficiency of the oscillating jet was higher than that of the free jet at the occupancy level, and the longitudinal oscillating jet purged pollutants faster than the transverse oscillating jet. This study reveals that oscillating jets can provide an option to create periodic flow fields and improve the efficiency of ventilation.

Electrochemical Performance of Nitrogen Self-Doping Carbon Materials Prepared by Pyrolysis and Activation of Defatted Microalgae.

Pyrolysis and activation processes are important pathways to utilize residues after lipid extraction from microalgae in a high-value way. The obtained microalgae-based nitrogen-doped activated carbon has excellent electrochemical performance. It has the advantage of nitrogen self-doping using high elemental nitrogen in microalgae. In this study, two kinds of microalgae, Nanochloropsis and Chlorella, were used as feedstock for lipid extraction. The microalgae residue was firstly pyrolyzed at 500 °C to obtain biochar. Then, nitrogen-doped activated carbons were synthesized at an activation temperature of 700-900 °C with different ratios of biochar and KOH (1:1, 1:2, and 1:4). The obtained carbon materials presented rich nitrogen functional groups, including quaternary-N, pyridine-N-oxide, pyrrolic-N, and pyridinic-N. The nitrogen content of microalgae-based activated carbon material was up to 2.62%. The obtained materials had a specific surface area of up to 3186 m2/g and a pore volume in the range of 0.78-1.54 cm3/g. The microporous pore sizes of these materials were distributed at around 0.4 nm. Through electrochemical testing such as cyclic voltammetry and galvanostatic charge-discharge of materials, the materials exhibited good reversibility and high charge-discharge efficiency. The sample, sourced from microalgae Chlorella residue at activation conditions of 700 °C and biochar/KOH = 1:4, exhibited excellent endurance of 94.1% over 5000 cycles at 2 A/g. Its high specific capacitance was 432 F/g at 1 A/g.

Application of graded phase change materials for solar energy inter-seasonal storage heating and thermal storage characteristics

Abstract In this paper, firstly, the heat transfer characteristics of the stepped phase change accumulator are studied, and the location of the solid-liquid phase interface is determined by the phase fraction in a fixed grid scheme, while the phase change heat transfer process is simulated using Fluent. Secondly, for the phase change heat transfer problem, the enthalpy-porosity method in the Solidification/Melting model is used to treat the solid-liquid mixed paste region of the phase interface as a porous media region, and the evaluation system is constructed in terms of heat storage and discharge efficiency, heat storage, and heat recovery efficiency. Then the mathematical model, boundary conditions and solution parameters of the stepped phase change heat accumulator are set, and the data analysis of the effect of the pool height-to-diameter ratio on the heat storage in the solar inter-seasonal storage heating system is carried out by using ANSYSCFD software. The results show that the heat storage of the system also shows an overall increasing trend with the increase of the pool height-to-diameter ratio, and the heat storage of the system increases faster when the height-to-diameter ratio increases from 0.2 to 1.0 in sequence, and the heat storage of the system increases less when the height-to-diameter ratio changes between 0.9 and 1.8, and basically tends to be stable. This study realizes the graded heat storage and graded heat use of solar energy, which is useful for the research of solar heat supply and heat storage.

Dynamic Cross-Linked Polyethylene Networks with High Energy Storage and Electrical Damage Self-Healability.

Dielectric polymers that exhibit high energy density Ue, low dielectric loss, and thermal resistance are ideal materials for next-generation electrical equipment. The most widely utilized approach to improving Ue involves augmenting the polarization through increasing the dielectric constant εr or the breakdown strength Eb. However, as a conflicting parameter, the dielectric loss also increases inevitably at the same time. In addition, due to the long-term work under a strong electric field or high potential, dielectric materials often produce electrical damage (electrical tree), which is one of the main factors affecting the reliability and service life of electrical equipment. To address these problems, we herein develop dynamic cross-linked polyethylene materials (PE-MA-Epo) by polyethylene-graft-maleic anhydride (PE-MA) and polar epoxy monomers, which showed high εr (>7), low dielectric loss (<0.02), high Ue (5.16 J/cm3 at 425 MV/m), and outstanding discharge efficiency (97%). The performances of the materials are adequate to rival biaxially oriented polypropylene (BOPP) films. Moreover, the excellent self-healing capability of PE-MA-Epo enables the total recovery of εr and tan δ after electrical tree healing. After two cycles of electrical breakdown healing, Eb remained at 80%, which improves the durability and reliability of dielectric polymers. Therefore, PE-MA-Epo shows great potential for applications in advanced electronic power devices.

Sandwich-structured BOPET films with high energy density and low loss for high temperature film capacitors

Film capacitors have widely been used in modern electrical/electronic equipment because of their high insulation property and high-power density. However, the traditional dielectric films suffered a high conduction loss under high temperature and electric field conditions, which leads to the depression of high temperature energy storage properties. Herein, sandwich-structured composite films using biaxially oriented polyethylene terephthalate (BOPET) as the outer layers were prepared to construct the interfacial barrier, which was beneficial for hindering the propagation of breakdown path. In addition, epoxy resin was applied as the adhesive inner layer to bind the outer layers up tightly, while the boron nitride nanosheets (BNNSs) in the inner layer further improved the breakdown strength of the film and inhibited the conduction loss, especially under high temperature and electric field conditions. The composite film with optimized BNNSs content had a high discharged energy density of 9.11 J/cm3 and a ultrahigh charge–discharge efficiency of 95% at 25 °C, while the values were 6.45 J/cm3 and 70% at 150 °C, respectively, of which both were much higher than those of pure BOPET. Thus, the sandwich-structure method points out a promising way of preparing dielectric films with excellent energy storage performances.

Combined Pericapsular Nerve Group Block and Intrapelvic Lateral Femoral Cutaneous Nerve Block Is Associated With Decreased Opioid Consumption After Hip Arthroscopy: A Retrospective Cohort Study.

Ambulatory hip arthroscopies are associated with moderate-to-severe pain often requiring opioid analgesia. Novel motor-sparing blocks, the pericapsular nerve group (PENG) and lateral femoral cutaneous nerve (LFCN) block, have shown efficacy in hip surgery. We sought to investigate the analgesic benefits of these novel blocks in terms of opioid-sparing and discharge efficiency. We conducted a retrospective cohort study with propensity score matching of 224 patients who underwent ambulatory elective unilateral hip arthroscopy. One group received a combined PENG and LFCN block (PENG/LFCN, n = 86), while a second group received only a PENG block (n = 26). A control group (n = 112) received no blocks. The primary outcome was postanesthesia care unit (PACU) mean opioid consumption. Secondary outcomes were maximum numeric rating scale (NRS) pain score, intravenous rescue analgesia, and PACU readiness-for-discharge times. The PENG/LFCN-block group required significantly less opioids than the control group in the PACU (25.98 ± 13.04 vs 14.58 ± 5.77, respectively) and were discharged earlier 2.72 ± 1.16 vs 4.42 ± 1.63 hours, respectively). The combined PENG/LFCN group also used less intravenous rescue opioids than the control group (0.47 ± 1.18 vs 1.44 ± 2.1 mg, respectively) and showed a significant difference in the highest NRS pain scores than the control group (6.01 ± 2.38 vs 6.77 ± 2.1 respectively). The PENG block alone group did not show a significant difference in opioid reduction (21.95 ± 15.83 vs 27.72 ± 15.01, respectively). This retrospective study found that in patients who underwent ambulatory elective unilateral hip arthroscopy, a combined PENG and LFCN block was associated with expedited PACU discharge and a clinically significant reduction in postoperative opioid use. Further study is warranted.

Wide Bandgap Heterostructured Dielectric Polymers by Rapid Photo‐Crosslinking for High‐Temperature Capacitive Energy Storage

AbstractPolymer dielectrics capable of operating stably at high temperatures (&gt;150 °C) are urgently in great demand to catch up with the booming electric power systems. Enhancing the heat resistance of polymers is typically achieved through thermal crosslinking with the use of crosslinking agents. Unfortunately, the conventional thermal crosslinking faces challenges in terms of commercialization due to its complex fabrication, inevitable introduction of small molecule impurities, and significant time and energy consumption. Here, a convenient, impurity‐free, time and energy efficient photo‐crosslinking method to create wide bandgap heterostructures within a dielectric polymer matrix, is presented. Remarkably, this approach achieves synergistically enhanced heat resistance and electrical insulation. Surprisingly, the crosslinked polymer exhibits an unprecedented Weibull characteristic breakdown strength of 1057 and 810 MV m−1 at room temperature and at 150 °C, respectively, which corresponds to superior energy storage densities of 14.28 and 5.55 J cm−3 with a charge–discharge efficiency of 90%, respectively. Furthermore, the polymer demonstrates an excellent electrical breakdown self‐healing character. These remarkable achievements, combined with the convenient and cost‐effective fabrication process, highlight the potential of cinnamate photo‐crosslinking in advancing high‐performance polymer dielectrics.

Effect of Carrier Film Phase Conversion Time on Polyacrylate Polymer Electrolyte Properties in All-Solid-State LIBs

To optimize the preparation process of polymer electrolytes by in situ UV curing and improve the performance of polymer electrolytes, we investigated the effect of carrier film phase conversion time on the properties of polymer electrolyte properties in all-solid-state LIBs. We compared several carrier films with phase conversion times of 24 h, 32 h, 40 h, and 48 h. Then, the physical properties of the polymer electrolytes were characterized and the properties of the polymer electrolytes were further explored. It was concluded that the carrier membrane with a phase transition time of 40 h and the prepared electrolyte had the best performance. The ionic conductivity of the sample was 1.02 × 10−3 S/cm at 25 °C and 3.42 × 10−3 S/cm at 60 °C. At its best cycle performance, it had the highest discharge-specific capacity of 155.6 mAh/g, and after 70 cycles, the discharge-specific capacity was 152.4 mAh/g, with a capacity retention rate of 98% and a discharge efficiency close to 100%. At the same time, the thermogravimetric curves showed that the samples prepared by this process had good thermal stability which can meet the various requirements of lithium-ion batteries.

EFFECT OF CHEMICALS ON RECOVERY OF CLOGGED DRIP EMITTERS FOR MAXIMUM UTILIZATION OF TREATED EFFLUENT FOR IRRIGATION

The growth in agriculture production is possible with wastewater utilization using the advanced technology of Drip Irrigation System (DIS). Drip irrigation is negatively affected by emitter clogging which entails reduced emitter discharge and irrigation system efficiency. The role of acid and chlorine contact time in emitter recovery with treated effluent is crucial. A combination of phosphoric acid (30,20 and 10 minutes) and sodium hypochlorite contact times (30,25 and 20 minutes) was used to study the recovery of in-line labyrinth drippers clogged with Treated Effluent (TE). A 1.2 ml/L of phosphoric acid and 20 mg/l of sodium hypochlorite was injected singly using a venturi dosing system. Nine (9) laterals with clogged emitters were implemented for treatment and the recovery discharge rates were measured for 5 minutes and characterized. Physicochemical and biological water analyses were carried out to determine parameters triggering clogging and the effect on recovery. The results showed that the chemical treatments had a significant effect on clog removal and recovered the discharge rates by 99.89 % of the initial flow at acid and chlorine contact times of 30 minutes each. This also had a relatively major effect alleviating emitter clogging from a discharge ratio variation (Dra) value of 33.50% to 123.23%. The recovery Dra values in each contact time with the chemicals were deemed effective (Dra≥ 75%). This was an indication that clogging in this study was mainly due to the chemical precipitation of Fe, Ca2+ and pH of the wastewater. The acid dissolved the mineral precipitates and chlorine disintegrated the organic matter built-ups. ANOVA tests for the acid and the chlorine contact time indicated that there were no statistically significant differences at p&lt;=0.05 on the effect of the average flow. This could be indicative of the sole effect of the phosphoric acid and sodium hypochlorite on the different clog type target. The chemical treatments recovery on CV, Uc and Dra could address the constraints in DIS and provide sustainable practice guidelines for the reduction of clogging, more beneficial because it can improve the system’s irrigation efficiency with the utilization of TE

Evaluation of carbon emission efficiency based on urbanscaling law: take 308 cities in China as an example.

The development of urban low carbonization is an important foundation for achieving the goal of "dual carbon." The differences in spatial differences based on scientific methods revealing the characteristics of urban carbon emissions and its efficiency are of great significance for shaping the green low-carbon land space pattern. This article uses urban standard models and scale adjustments to the urban index (SAMIs) identification in 2006-2017 308 Chinese urban carbon discharge standards and efficiency time and space evolution pattern and their characteristics. The results of the study show that there is a stable secondary relationship between carbon emissions and urban population scale, which means that the growth rate of urban carbon emissions is significantly lagging behind the growth of urban systems. The analysis of urban carbon emission efficiency based on SAMI values shows significant spatial heterogeneity: the carbon emission efficiency of cities in North China, East China, and Northeast China is lower than that of other regions. In terms of temporal changes, there was a phenomenon of SAMI high-value cities moving north and low-value cities moving south between 2006 and 2017, and △SAMIs showed a pattern of hot in the west and cold in the east. This study broadens the applicability of urban scaling law models in urban environmental research, providing a new perspective for evaluating urban carbon emission efficiency and China's energy conservation and emission reduction work.

Communicating Patient Discharge Readiness: An Implementation Evaluation in an Inpatient Hospital Medicine Setting.

The progression of patients through a hospital from admission to discharge can be slowed by delays in patient discharge, increasing pressure on health care staff. We designed and piloted the Discharge Today tool, with the goal of improving the efficiency of patient discharge; however, adoption remained low. To close this implementation gap, we deployed and evaluated a 4-part implementation strategy bundle. We measured the success of implementation by evaluating validated implementation outcomes using both quantitative and qualitative methods, grounded in Normalization Process Theory. The implementation strategies used were effective for increasing use of the Discharge Today tool by hospital medicine physicians and advanced practice providers during both the active and passive implementation periods. While the implementation strategies used were effective, qualitative findings indicate that limitations in the functionality of the tool, alongside inconsistent use of the tool across clinical staff, continued to inhibit adoption.