Direction Of Thermal Gradient Research Articles

Influence of thermal conductivity on evolution of grain morphology during laser-based directed energy deposition of CoCrxFeNi high entropy alloys

A model CoCrxFeNi high entropy alloy system was chosen to investigate the effect of thermal conductivity on the evolution of spatial orientation of columnar grain morphology during laser directed energy deposition. The thermal conductivity of the alloy was varied by tuning the chromium content in CoCrxFeNi alloys. CoCrxFeNi alloys with chromium content ranging between 0 and 24 at% were produced under identical processing conditions of laser direct energy deposition method. Electron back scattered diffraction images of the cross-sections revealed that the spatial orientation of grain morphology transitioned from zigzag columnar grains from layer-to-layer to near-continuous columnar grains across multiple layers with increased content of chromium in CoCrxFeNi. A multi-scale multi-physics finite element based thermo-kinetic model with consideration to multi-track multi-layer nature of the laser direct energy deposition technique was adopted to correlate the process thermo-kinetics with the evolution of microstructure. The computation calculations revealed that the decrease in thermal conductivity from 36 W/m.K (CoFeNi) to 26 W/m.K (CoCr24FeNi) at the melting point reduced the cooling rate from 3.3 ×104 °C/s to 1.3 ×104 °C/s in CoFeNi and CoCr24FeNi alloys, respectively. This subsequently evolved into increased degree of remelting of previously deposited layers and caused the direction of resultant thermal gradient to reorient towards the build direction. Such reorientation in resultant thermal gradient contributed to transition of spatial orientation of grain morphology from columnar zigzag microstructures from layer-to-layer to near continuous columnar grains across multiple layers. The present observation was verified compared with other reported metallic systems exhibiting zigzag and continuous columnar grains, and a unified mechanism underlining the role of thermal conductivity on microstructure evolution was proposed.

Achieving a Columnar-to-Equiaxed Transition Through Dendrite Twinning in High Deposition Rate Additively Manufactured Titanium Alloys

AbstractThe coarse β-grain structures typically found in titanium alloys like Ti–6Al–4V (wt pct, Ti64) and Ti–6Al–2Sn–4Zr–2Mo–0.1Si (Ti6242), produced by high deposition rate additive manufacturing (AM) processes, are detrimental to mechanical performance. Certain modified processing conditions have been shown to lead to a more refined grain structure, which has generally been attributed to a change in the solidification conditions with respect to the experimental Hunt diagram proposed by Semiatin and Kobryn. It is shown that with Wire Arc AM (WAAM) increasing the wire feed speed (WFS) is effective in promoting a columnar-equiaxed transition (CET). Conversely, estimates of the dendrite-tip undercooling using the KGT model suggest that this will be too small for free nucleation without the addition of artificial nucleants, due to the very low solute partitioning in Ti alloys. It is also shown that it is difficult to promote a CET with plasma transferred arc WAAM as computational fluid dynamics (CFD) melt-pool simulations indicate that the solidification parameters remain within the columnar region on the Semiatin-Kobryn Hunt map, within the constraints of a stable process. However, a high fraction of twin boundaries was observed in the refined β-grain structures seen at high WFS. This has been attributed to departure of $$\left\langle {001} \right\rangle _{\beta }$$ 001 β alignment from the direction of maximum thermal gradient, caused by the curvature of the fusion boundary, stimulating dendrite twinning during solidification. In addition, it is shown that increasing the WFS leads to a change in melt-pool geometry and a reduction of remelt depth, which promoted dendrite twinning and grain refinement.

A model for thermocapillary driven motion of liquid drops on an inclined plane

Thermocapillary drop migration is driven by surface tension gradient. On an inclined plane, gravity acts as an additional force that can have a promoting or resisting effect depending on the thermal gradient direction. The present 2-D model extends Brochard and Chebbi models for thermocapillary migration of small drops on horizontal plates by accounting for Marangoni and Poiseuille flow components, while including the effect of gravity, acting in the case of inclines. The present treatment is based on fundamentals of conservation of mass and momentum transport, and uses the lubrication approximation and extended boundary conditions at the receding and advancing contact lines. A model for the dynamics of migration is provided, and an analytical solution is derived for drop migration dynamics and the critical angle of inclination.

Magnetoinduced spin Nernst effect in topological nodal-line semimetals

The spin Nernst effect (SNE) of a topological nodal-line semimetals (TNLSMs) nanowire in a four-terminal cross-bar device is studied. Based on the nonequilibrium Green’s function method combining with the tight-binding Hamiltonian, the spin Nernst coefficients Ns3z, Ns3x and Ns3y of the two thermal transport models (kz-y case and kx-y case) under a perpendicular magnetic field are obtained. The traditional SNE describes the transverse voltage and spin current caused by the longitudinal thermal gradient. The transverse spin current is generated by the spin–orbit interaction rather than the perpendicular magnetic field. Here we find that the spin Nernst coefficients are equal to zero at the zero-magnetic field, but have finite values for non-zero magnetic fields in TNLSMs. The spin Nernst coefficient is closely related to the strength of the magnetic field and temperature. With the increase of the magnetic field strength, the peak height of the spin Nernst coefficient increases. These results indicate that the SNE is induced by the perpendicular magnetic field in the present TNLSMs system, which can be considered as an anomalous spin Nernst phenomenon. In addition, we find that Ns3z displays a series of peaks when the transmission coefficient TLR jumps from one integer plateau to another, and the spin Nernst coefficient Ns3i (i=x,y,z) is an odd function of the Fermi energy EF with Ns3z/x/y(−EF)=−Ns3z/x/y(EF) in connection mode kz-y. For the kx-y connection mode, due to the presence of the mass term m opening the energy gap, a sudden jump of the transmission coefficient TLR in the vicinity of the energy gap edge causes a very larger peak for the spin Nernst coefficient Ns3z/x/y, and the symmetrical properties of the spin Nernst coefficient Ns3z/x/y are completely broken in the strong magnetic field. These results indicate that the spin Nernst coefficient in TNLSMs strongly depends on the thermal gradient direction and the transverse lead connection direction. The spin Nernst coefficient in TNLSMs has strongly spatial anisotropy, which can be used as the characterization of the experimental detection of TNLSMs.

Microstructure and Crystallographic Texture Evolution of β-Solidifying γ-TiAl Alloy During Single- and Multi-track Exposure via Laser Powder Bed Fusion

The microstructural evolution and crystallographic texture formation of β-solidifying Ti-44Al-6Nb-1.2Cr alloy were identified under single- and multi-track exposures via laser powder bed fusion (L-PBF) for various process parameters. Under single-track exposure, the microstructure of the melt pool was divided into the band-like α2 phase in the melt pool boundary and β phase in the melt pool center. Numerical and thermodynamic simulations revealed that the underlying mechanism of phase separation was related to the variation in the cooling rate in the melt pool, whereas microsegregation induced a shift in the solidification path. Meanwhile, the crystallographic texture of the α2 phase region was identical to that of the substrate owing to the epitaxial growth of the β phase and subsequent α phase nucleation. In contrast, the β phase exhibited a ± 45° inclined <100> alignment in the melt pool, which was tilted to align along the build direction toward the center of the melt pool corresponding to the simulated thermal gradient direction. Furthermore, the narrow hatch space condition maintained the crystallographic texture to the subsequent scan, forming a continuous band-like α2 phase with a strong selection. However, the crystallographic texture in a wide hatch space condition manifested a random distribution and constituted a fine mixture of the β and α2 phases. For the first time, these results will offer an understanding of an anisotropic microstructure control via the L-PBF process and ensure the tailoring of the mechanical properties in the β-solidifying γ-TiAl-based alloys by approaching hatch spacing control.Graphic

Experimental and numerical analysis of CMCs mechanical properties under high-temperature thermal gradient environment

This paper carried out a high-temperature thermal gradient cycling test of ceramic matrix composites (CMCs), investigating the failure characteristics of CMCs in non-uniform high-temperature environments. The result shows that the damage characteristics of CMCs under thermal gradient environments are significantly different from those under uniform temperature environments. The SiC fiber pull-out lengths at different yarn fractures have obvious differences in the thermal gradient direction. The thermal stress damage propagation pattern of CMCs under the thermal gradient environment is revealed by numerical analysis, and its residual mechanical properties under different thermal gradient environments are predicted. The numerical results could be adopted as a theoretical basis and suggestions for temperature control of CMCs components in practical applications.

Presolidification in Eutectic Droplets.

Evidence of presolidification, the counterpart to premelting, is reported. Near the eutectic temperature, T_{C}, the propagation direction of thermal gradient driven motion of eutectic Ge-Pt droplets on Ge(110) is determined by presolidification. Well above T_{C}, the micron-sized droplets move towards the hottest location at the substrate, irrespective of crystalline direction. At 90K above T_{C}, a strong, unanticipated preference for propagation along the substrate [001] azimuth suddenly emerges, which is attributed to presolidification at the liquid-solid interface. The propagation along [001] is accompanied by a distinct change in shape from compact to elongated along [001].

3D Modeling of the Solidification Structure Evolution and of the Inter Layer/Track Voids Formation in Metallic Alloys Processed by Powder Bed Fusion Additive Manufacturing.

A fully transient discrete-source 3D Additive Manufacturing (AM) process model was coupled with a 3D stochastic solidification structure model to simulate the grain structure evolution quickly and efficiently in metallic alloys processed through Electron Beam Powder Bed Fusion (EBPBF) and Laser Powder Bed Fusion (LPBF) processes. The stochastic model was adapted to rapid solidification conditions of multicomponent alloys processed via multi-layer multi-track AM processes. The capabilities of the coupled model include studying the effects of process parameters (power input, speed, beam shape) and part geometry on solidification conditions and their impact on the resulting solidification structure and on the formation of inter layer/track voids. The multi-scale model assumes that the complex combination of the crystallographic requirements, isomorphism, epitaxy, changing direction of the melt pool motion and thermal gradient direction will produce the observed texture and grain morphology. Thus, grain size, morphology, and crystallographic orientation can be assessed, and the model can assist in achieving better control of the solidification microstructures and to establish trends in the solidification behavior in AM components. The coupled model was previously validated against single-layer laser remelting IN625 experiments performed and analyzed at National Institute of Standards and Technology (NIST) using LPBF systems. In this study, the model was applied to predict the solidification structure and inter layer/track voids formation in IN718 alloys processed by LPBF processes. This 3D modeling approach can also be used to predict the solidification structure of Ti-based alloys processes by EBPBF.

Poly(butylene succinate) matrices obtained by thermally-induced phase separation: Pore shape and orientation affect drug release

Poly(butylene succinate) (PBS) scaffolds with 3D microporous interconnected architecture and crystallized PBS substructures have been prepared by thermally-induced phase separation (TIPS). Curcumin (CUR) and piperine (PIP) natural drugs were incorporated into the matrices during a one-step fabrication protocol. Alterations in TIPS parameters such as solvent system (1,4 dioxane (DXN) or THF) and cooling condition (intensity and direction of thermal gradient) affected the phase separation process and the scaffold properties. Controlling the crystallization of DXN in a uniaxial direction, resulted in the formation of microtubular scaffolds with oriented porosities. Well-developed PIP crystals and matrix-integrated CUR agglomerates were uniformly distributed throughout the scaffolds. The integration of CUR to the polymer matrix was confirmed by physicochemical evaluations, attributed to a possible interaction with PBS, resulting in a slower release than PIP. The scaffolds with uniaxially-oriented porosities displayed a greater sustained release (only 50–60% after 170 h) due to the restricted drug diffusion through their dense spherulitic pore walls. Due to such structure and smoother well-arranged surfaces, the oriented scaffolds also exhibited greater biocompatibility. Our results reveal the positive influence of TIPS-derived structural orientation on properties of PBS matrices for cell/drug delivery. • Controlling the porous architecture is crucial to designing cell/drug carriers. • Porosity orientation affects the final properties of the polymeric matrix. • Herein, porosity orientation has been controlled by adjusting TIPS thermal gradient. • Uniaxially-aligned pores had spherulitic and denser walls compared to random ones. • Such a structure could impede the drug diffusion, being achieved a sustained release.

Comparative Study on Effects of Thermal Gradient Direction on Heat Exchange between a Pure Fluid and a Nanofluid: Employing Finite Volume Method

This work aims to determine how the temperature gradient orientation affects the heat exchange between two superposed fluid layers separated by zero wall thickness. The finite volume method (FVM) has been developed to solve the governing equations of both fluid layers. To achieve the coupling between the two layers, the heat flow continuity with the no-slip condition at the interface was adopted. The lower part of the space is filled with a nanofluid while the upper part is filled with a pure fluid layer. We have explored two cases of temperature gradient orientation: parallel gradient to gravity forces of our system and perpendicular gradient to gravity forces. We took a set of parameters, Ri and ϕ, to see their influence on the thermal and hydrodynamic fields as well as the heat exchange rate between the two layers. The main applications of this study related to biological systems such as the cytoplasm and the nucleoplasm are phase-separated solutions, which can be useful as models for membranelles organelles and can serve as a cooling system application using heat exchange. The Richardson number and the volume of nanosolid particles have a big impact on the rate of change of heat transmission. When a thermal gradient is perpendicular to gravity forces, total heat transmission improves with increasing solid volume percentage, but when the thermal gradient is parallel to gravity forces, overall heat transfer decreases significantly.

Flexible, scalable, and efficient thermoelectric touch detector based on PDMS and graphite flakes

This paper presents freestanding thermoelectric touch detectors consisting of graphite conductive flakes into a polydimethylsiloxane matrix. An optimal concentration of graphite flakes (45 wt%) lead to robust and homogeneous detectors that exhibited signal-noise ratio values up to 170 with rise and falling times below 1 s and 7 s, respectively. The detectors performance was stable over continuous operation and did not reveal significant degradation while bended under different curvature radii (45, 25 and 15 mm) and consecutive bending cycles. Moreover, the twist of the thermal gradient direction between the electrodes of the detector enables a Yes or No response which opens new usage possibilities. Therefore, this work provides an efficient way to develop robust, low-cost, and scalable thermal detectors with potential use in wearable technologies.

Deterministic modeling of solidification microstructure formation in directed energy deposition fabricated Ti6Al4V

Metal additive manufacturing (MAM) technology is now widely applied in the manufacturing and remanufacturing industry, among which microstructure simulation gradually shows its importance. Traditional solidification microstructure simulation methods all have their merits as well as drawbacks when applied in MAM cases. In this work, a deterministic solidification microstructure model, named “invasion model”, is established to avoid the essential defects of traditional methods. This model focuses on the interaction between the neighboring bi-crystals instead of simulating the growth kinetics of each columnar grain or deriving the field form of variables. Within a bi-crystal system, the grain boundary tilt from thermal gradient direction is understood as a transient invasion behavior of one grain to another, and the competitive grain growth behavior along the buildup process of MAM is a summary of all the invasions in bi-crystal systems. To fill the gaps in the rapid solidification theory, a database recording the anisotropic growth effect under a rapid directional solidification condition was established with the help of an artificial neural network (ANN). Wire feed directed energy deposition (DED) fabricated Ti6Al4V thin-wall samples with full dendritic columnar grains (prior beta) are used as a benchmark to test the validation of the novel simulation model. The grain geometrical structure of reconstructed prior β grains along the build-up direction has a good agreement with the simulation result. The model can also be applied to other cases of MAM or combine with various models to achieve real-time as-solidified crystallographic feature prediction when it meets the scope of application. • Traditional solidification microstructure simulation methods all have their merits and drawbacks when applied in MAM cases. • Invasion model is established to investigate the transient competitive grain growth behavior within bi-crystal systems. • Wire DED Ti6Al4V thin-wall samples are used as a benchmark to test the validation of the novel simulation model.

Tailored grain morphology via a unique melting strategy in electron beam-powder bed fusion

This study presents a unique melting strategy in electron beam-powder bed fusion of Alloy 718 to tailor the grain morphology from the typical columnar to equiaxed morphology. For this transition, a specific combination of certain process parameters, including low scanning speeds (400–800 mm/s), wide line offsets (300–500 μm) and a high number of line order (#10) was selected to control local solidification conditions in each melt pool during the process. In addition, secondary melting of each layer with a 90° rotation with respect to primary melting induced more vigorous motions within the melt pools and extensive changes in thermal gradient direction, facilitating grain morphology tailoring. Four different types of microstructures were classified according to the produced grain morphology depending on the overlap zone between two adjacent melt pools, i.e., fully-columnar (overlap above 40 %), fully-equiaxed (overlap below 15 %), mixed columnar-equiaxed grains, and hemispherical melt pools containing mixed columnar-equiaxed grains (overlap ~20–25 %). The typical texture was <001>; however, the texture was reduced significantly through the transition from the columnar to equiaxed grain morphology. Along with all four different microstructures, shrinkage defects and cracks were also identified which amount of them reduced by a reduction in areal energy input. The hardness was increased through the transition, which was linked to the growth of the γʺ precipitates and high grain boundary density in the fully-equiaxed grain morphology.

Kinetic Monte Carlo simulations of the sintering microstructural evolution in density graded stainless steel fabricated by SPS

The microstructural evolution and sintering behavior of density graded stainless steel 304 L were evaluated using three-dimensional kinetic Potts Monte Carlo simulations. Density graded samples were fabricated using spark plasma sintering (SPS) and were axially divided into five regions in the thermal gradient direction to quantify the density variations using images obtained through scanning electron microscopy (SEM). Finite element analysis was then utilized to quantify the temperature gradient within the samples. Subsequently, two different kinetic Monte Carlo (kMC) simulations were applied to evaluate the microstructural evolution in the samples. The simulation results were compared with the density values obtained from the SEM images and the overall density measurements of the samples. Microstructural evolution parameters, such as densification and sintering stress profiles, were then obtained, followed by the evaluation of the effects of several parameters on the density profiles of the SPS-sintered samples. The results show that kMC simulations accurately evaluate the microstructural evolution of sintering, quantify the sintering behavior, and predict the effects of several parameters on the density profiles. kMC simulations of density graded material sintering provide predictive results to control the resulting sintered microstructure and to identify the sintering stage of each region of the density graded samples.

Overgrowth behavior at converging grain boundaries during competitive grain growth: A two-dimensional phase-field study

Herein, three types of converging grain growth were investigated during directional solidification, through two-dimensional phase-field simulations. The three types were distinguished by the orientation of the favorably oriented (FO) dendrites. The growth orientation of the FO dendrites was parallel to the thermal gradient direction in type I, whereas the orientation of FO dendrites was inclined in the same and opposite lateral directions as those of the unfavorably oriented (UO) dendrites in types II and III, respectively. The largest difference between FO and UO grain inclination angles—that is, the threshold angle, for unusual overgrowth in different alloy systems were clearly different, in type I and III cases. In all three types of converging grain growth, overgrowth of UO dendrites by FO dendrites (usual overgrowth) was observed to occur more frequently than that of FO dendrites being overgrown by UO dendrites (unusual overgrowth). The asymmetry of the inclined dendrite diffusion layer caused different solute interactions in the three types of converging grain growths. Based on the different solute interactions, unusual overgrowth behavior occurred most readily in type III cases—and with most difficulty in type II cases. We also saw that the local GB orientation may alternate between FO and UO grain orientations in type III cases.

Phase-field simulations and microstructural analysis of epitaxial growth during rapid solidification of additively manufactured AlSi10Mg alloy

In metal additive manufacturing, the unique microstructure from extreme process conditions determines the properties of the build part. In this study, the microstructural evolution of the additively manufactured AlSi10Mg alloy was studied to elucidate the relationship between its growth morphology and the local thermal gradient during rapid solidification. The microstructure of a uniaxially built specimen, as analyzed by electron backscatter diffraction (EBSD), exhibiting the [100](001) texture along the building direction. To investigate the local growth morphology, phase-field simulations were performed to examine the effect of grain misorientation on the previously built layer with respect to the thermal gradient direction. Furthermore, the solidification of partially melted microstructures observed during the EBSD measurements was simulated under the rapid solidification conditions. The obtained results revealed that the growth morphology of alloy grains during solidification strongly depended on the misorientation angle of the previously built layer measured with respect to the local thermal gradient direction. The simulated microstructures were in good agreement with the experimentally observed alloy morphology, which indicated that the utilized phase-field method could be potentially used in quantitative microstructural modeling.

Microstructure and grain growth direction of SRR99 single-crystal superalloy by selective laser melting

Nickel-based Single Crystal (SX) superalloys have an excellent creep ductility and thermal fatigue resistance at elevated temperatures. But SX structure is difficult to be manufactured under the demand of increasing operating temperature and complex shapes. In this work, the feasibility of manufacturing Nickel-based SX-superalloys by selective laser melting (SLM) was investigated theoretically and experimentally. Firstly, the solidification conditions including temperature field, thermal gradient and solidification speed of the SLMed multi-track samples were calculated by an established finite element model to judge the theoretical feasibility based on the columnar to equiaxed transition (CET). Then, the single-track, triple-track and cuboid samples on a single-crystal SRR99 substrate were deposited to judge the experimental feasibility and explore their grain growth mechanism during SLM. The results showed that CET can be avoided during the whole process of SLM. The unidirectional SRR99 SX structure with a height of 2 mm can be successfully obtained by SLM. On horizontal section, the microstructures can be divided into [001] orientation zone, [010] orientation zone and overlapping zone with a typical secondary dendrite structure. On vertical section, the columnar dendritic structure along the dominant thermal gradient direction is present. The primary dendrite spacing of the SLMed samples (∼1–2 μm) is more than two orders of magnitude lower than that of the cast one (∼320 μm). So, SLM technology possesses the capacity to manufacture SX superalloy. When the deposited height reaches 6 mm, the misorientation angle is about 25° and a crack initiates. Finally, the grain growth mechanism of the SLMed SRR99 single-crystal superalloy was proposed based on the local thermal gradient, the existing well-aligned crystallographic orientation and the preferential grain growth direction.

Anomalous spin Nernst effect in Weyl semimetals

The spin Nernst effect describes a transverse spin current induced by the longitudinal thermal gradient in a system with the spin–orbit coupling. Here we study the spin Nernst effect in a mesoscopic four-terminal cross-bar Weyl semimetal device under a perpendicular magnetic field. Because the spin current is a tensor, it has three elements with the spin direction pointing to the x, y and z directions when the spin current flows along the transverse lead. By using the tight-binding Hamiltonian combined with the nonequilibrium Green’s function method, the three elements of the spin current in the transverse leads and the spin Nernst coefficients are obtained. The results show that the spin Nernst effect in the Weyl semimetal has an essential difference to the traditional Nernst effect: we found that the z direction spin current is zero without the magnetic field while it appears under the magnetic field, and the x and y direction spin currents in the two transverse leads flow out or in together, in contrast to the traditional spin Nernst effect, in which the spin current is induced by the spin–orbit coupling and flows out from one lead and flows in on the other. We call it the anomalous spin Nernst effect. In addition, we show that the Weyl semimetals have inversion-type symmetry, mirror-reversal-type symmetry and electron–hole-type symmetry, which lead to the spin Nernst coefficients being either odd or even functions of the Fermi energy, the magnetic field and the transverse terminals. Moreover, the spin Nernst effect in the Weyl semimetals are strongly anisotropic and its coefficients are strongly dependent on both the direction of thermal gradient and the direction of the transverse lead connection. Three non-equivalent connection modes (x-z, z-x and x-y modes) are studied in detail, and the spin Nernst coefficients for three different modes exhibit very different behaviors. These strongly anisotropic behaviors of the spin Nernst effect can be used as the characterization of magnetic Weyl semimetals.

Effect of the misorientation angle and anisotropy strength on the initial planar instability dynamics during solidification in a molten pool

The initial planar instability will appear with the solute accumulation ahead of the solid/liquid (S/L) interface during solidification in a molten pool. The instability process is dominated by the misorientation angle and the surface tension anisotropy strength, where the misorientation angle is the angle between the preferred crystalline orientation of base metal and the thermal gradient direction in front of the S/L interface. In this study, their effects on the initial planar instability during gas tungsten arc welding of an Al-alloy are investigated using a modified analytic model and a quantitative phase-field model, respectively. Specifically, we apply the uniform fluctuation spectrum assumption, Aω(0) = kBTM/{γ0[1 − 15γ4cos(4θ0)]ω2}, to represent the influence of thermal noise on S/L interface evolution. The incubation time, average wavelength and detailed interface morphology of the initial planar instability are investigated with varying surface tension anisotropies (determined by anisotropy strength γ4 and misorientation angle θ0). The results indicate that -γ4cos(4θ0) is a reasonable indicator for the effect of surface tension anisotropy on the initial planar instability. Moreover, rather than influencing solute diffusion, the surface tension anisotropy just affects the planar interface stability during the solidification. Finally, the experimental observations with the same welding parameters was carried out, which are in general agreement with the simulated results.

Long-range transverse spin Seebeck effect in permalloy stripes using Sagnac interferometer microscopy

Coupling of spins and phonons in ferromagnets (FM) may persist up to mm length scale, thus generating macroscopic spatially distributed spin accumulation along the direction of an applied thermal gradient to an FM slab. This typical feature of transverse spin Seebeck effect (TSSE) has been demonstrated so far using electrical detection methods in FM films, in particular in a patterned structure, in which FM stripes grown onto a substrate perpendicular to the applied thermal gradient direction are electrically and magnetically isolated. Here we report optically detected TSSE response in isolated FM stripes based on permalloy deposited on SiN substrate, upon the application of a thermal gradient. For these measurements we used the magneto-optic Kerr effect measured by an ultrasensitive Sagnac interferometer microscope that is immune to thermo-electrics artefacts. We found that the optical TSSE coefficient in the NiFe stripes geometry is about one order of magnitude smaller than that in the continuous NiFe film, which is due to the limited phonons path in the FM stripes along the thermal gradient direction. Our results further confirm the existence of TSSE response in conducting FM compounds.