Dibutyl Sebacate Research Articles

Micro-Electrohydrodynamic Pump by Dielectric Fluid

A Micro-Electrohydrodynamic (EHD) pump is tested experimentally. The EHD pump examined in this paper is fabricated with two cylindrical copper electrodes of the inner diameter 3 mm. The distance between electrodes was changed from 0.6 mm to 1.2 mm. In order to simplify the characterization of the pressure capacity of the EHD pump, the uniform electric field added in the gap between the cylindrical electrodes using aluminum disc electrodes (40 mm outer diameter). The static pressure and the mean velocity in a closed fluidic circuit were measured with Dibutyl sebacate as working fluid. The liquid has a dielectric constant, e/e 0 = 4.8 and a low electric conductivity, σ=4.7× 10 -10 (S/m). The static pressure results are compared with the theoretical results. The theoretical model is based on the unipolar conduction which generates the space charge in the liquid. In this model, the Coulomb force can contribute to the EHD motion. The static pressure results show a linear relationship with the square of the electric filed. This linear relationship supports the assumption that the unipolar conduction generates the pressure driving force. The estimation of the EHD pump efficiency based on the theoretical model is 18% with the electrode gap of 1.2mm between the electrodes and 5% with the one of 0.6 mm.

Sorption in reconstituted waxes of homologous series of alcohol ethoxylates and n‐alkyl esters and their effects on the mobility of 2,4‐dichlorophenoxybutyric acid

Equilibrium sorption of n-alkyl esters (dimethyl suberate, diethyl suberate, diethyl sebacate, dibutyl suberate and dibutyl sebacate) and monodisperse alcohol ethoxylates (diethylene glycol, tetraethylene glycol, pentaethylene glycol, hexaethylene glycol and octaethylene glycol monododecyl ether) between the reconstituted cuticular waxes of Stephanotis floribunda Brongn (Madagascar jasmine) or Hordeum vulgare L (barley) leaves and an external aqueous receptor solution was determined. Logarithms of the wax/receptor partition coefficient (K(wax/rec)) of the n-alkyl esters increased linearly with the number of C-atoms. With alcohol ethoxylates, log K(wax/rec) decreased linearly with the number of ethylene oxide units. For both groups of compounds, K(wax/rec) increased with increasing lipophilicity. The values of K(wax/rec) in Stephanotis wax were between 5 and 16 times higher than in barley wax. It is argued that this difference was due to different chemical composition and crystallinity of the waxes. Mobility of [14C]2,4-dichlorophenoxybutyric acid (2,4-DB) in reconstituted Stephanotis and barley wax was increased by a factor of 2-8 by both n-alkyl esters and alcohol ethoxylates. Effects on the mobility of 2,4-DB were linearly related to the internal concentrations of n-alkyl esters and alcohol ethoxylates in reconstituted Stephanotis or barley wax. At the same internal concentrations the effect of n-alkyl esters on the mobility of 2,4-DB in wax exceeded that of alcohol ethoxylates by between 1 and 2 orders of magnitude. Results are discussed in relation to formulating systemic pesticides.

Polymer blends used for the aqueous coating of solid dosage forms: importance of the type of plasticizer

The aim of this study was to investigate the importance of the type of plasticizer in polymer blends used for the coating of solid dosage forms, comparing a lipophilic and a hydrophilic plasticizer (dibutyl sebacate (DBS) and triethyl citrate (TEC)). In vitro drug release from propranolol hydrochloride (propranolol HCl)-loaded pellets coated with blends of ethyl cellulose (EC) and Eudragit® L (100:0, 75:25, 50:50, 25:75 and 0:100 w/w) was investigated at low as well as at high pH. To better understand the underlying mass transport mechanisms, the physicochemical properties of the film coatings (e.g. mechanical resistance, water uptake and dry weight loss behavior) were determined. Interestingly, drug release strongly depended on the type of plasticizer. Importantly, not only the slope but also the shape of the release curves was affected, indicating that the chemical nature of the plasticizer plays a major role for the underlying drug release mechanisms. Diffusion through the intact polymer coatings and/or through water-filled cracks was found to be dominating for the control of drug release. The relative importance of these pathways strongly depended on the polymer blend ratio and type of plasticizer. In contrast to DBS, TEC rapidly leached out of the coatings, resulting in decreasing mechanical resistances of the films and, thus, facilitated crack formation. In addition, the hydrophilicity of the plasticizer significantly affected the water uptake behavior of the film coatings and, hence, changes in the coatings' toughness and drug permeability. Also the relative affinity of the plasticizer to the different polymers was found to be of significance. In contrast to TEC, DBS has a higher affinity to EC than to Eudragit® L, resulting in potential redistributions of this plasticizer within the polymeric systems and changes in the release profiles during storage. Importantly, these effects could be avoided with appropriate curing conditions and preparation techniques for the coating dispersions.

Polymeric membrane electrodes with enhanced fluoride selectivity using Zr(IV)-porphyrins functioning as neutral carriers

Poly(vinyl chloride) polymeric membranes plasticized with o-NPOE ( o-nitrophenyl octyl ether) or DOS (dibutyl sebacate) and containing Zr(IV)-octaethyl(OEP)- or Zr(IV)-tetraphenylporphyrins (TPP) along with lipophilic cationic additives (tridodecylmethylammonium chloride; TDMACl) are examined potentiometrically and optically with respect to their response toward fluoride. It is shown that these zirconium porphyrins can function as neutral anion carriers within the organic membranes of the electrodes. Spectrophotometric measurements of thin polymeric films indicate that the presence of lipophilic cationic sites in the form of TDMA + and use of lower dielectric constant plasticizer (DOS) prevents formation of metalloporphyrin dimers in the organic polymer phase, which have been observed previously in polymeric membranes formulated with the same Zr(IV) porphyrins but with lipophilic anion site additives. By preventing dimer formation, rapid and Nernstian potentiometric response of the corresponding membrane electrodes toward fluoride ion is observed. Indeed, electrodes prepared with PVC/DOS membranes containing Zr(IV)-OEP and 15 mol% of TDMACl (relative to the ionophore) exhibit fast ( t 95<15 s) and reversible response toward fluoride. The slope of calibration plots are near-Nernstian (−59.9 mV per decade). Such electrodes display the following selectivity pattern: ClO 4 −>SCN −>F −>NO 3 −>Br −>Cl −, which differs significantly from the classical Hofmeister series, with greatly enhanced potentiometric selectivity toward fluoride. The data presented herein, coupled with results from a previous study, confirm that Zr(IV) porphyrins can serve as either charged or neutral type anion carriers with respect to their enhanced interactions with fluoride when used as ionophores to prepare liquid–polymeric membrane electrodes, and that the nature of membrane additives and plasticizer dictates the response mechanism at play for given membrane formulations.

Characterization of Plasticized PEO Based Solid Polymer Electrolyte by XRD and AC Impedance Methods

The ionic conductivity of lithium based solid polymer films prepared from poly (ethylene oxide) (PEO) and lithium hexafluoarsenate (LiAsF6) with varying compositions of plasticizers like dibutyl sebacate (DBS) and ethylene carbonate (EC) was measured by AC impedance method. Polymer film composition viz. (PEO)8LiAsF6-(DBS)0.4-(EC)0.1 has been evaluated as an optimum composition as evidenced from its high conductivity and freestanding ability. The high conductivity observed for the polymer electrolyte with this composition has been attributed to an enhanced amorphous character and a reduced energy barrier to the segmental motion of lithium ions in the matrix. The temperature dependence of conductivity on the polymer films, with and without plasticizers, appears to obey the Arrhenius law. However, the activation energy of the plasticized polymer film is 0.81 KJ/mol, a value considerably lower than 10 KJ/mol obtained for the unplasticized electrolyte, making the polymer to be a prospective candidate as lithium-ion conducting electrolyte for rechargeable lithium batteries.

Relationship between plasticizer content and tensile bond strength of soft denture liners to a denture base resin.

The purpose of this study was to determine the influence of plasticizer content on the tensile bond strength of heat-cured acrylic soft denture liners to a denture base resin. Differences among materials were significant, except for 100 wt% Dibutyl Sebacate (DBS) and 80 wt% DBS of tensile bond strength. The bond strength of all materials to the denture base increased with an increase in thermal cycles significantly except for 40 wt% DBS. The tensile bond strength of soft denture liners to the denture base resin significantly decreased with an increase of plasticizer contents. Differences were found among the difference plasticizer contents in failure types between the denture base resin and soft denture liners. The results suggest that the tensile bond strengths of heat-cured acrylic soft denture liners to the denture base resin were lower with an increase in plasticizer content.

Enhanced film-forming properties for ethyl cellulose and starch acetate using n-alkenyl succinic anhydrides as novel plasticizers.

The aim of this study was to investigate the ability of n-alkenyl succinic anhydrides (n-ASAs) to improve the film-forming characteristics of a novel coating polymer, potato starch acetate degree of substitution 2.8 (SA). n-ASAs were also applied to improve the otherwise brittle properties of ethyl cellulose (EC) aqueous dispersion (Aquacoat) and EC solvent-based films. The effectiveness of two n-ASAs, 2-octenyl succinic anhydride (OSA) and 2-dodecen-1-ylsuccinic anhydride were evaluated as plasticizers. Mechanical properties, both water vapor and drug permeabilities, and glass transition temperatures of the cast free films were measured. Triethyl citrate and dibutyl sebacate were used as reference plasticizers. The long hydrocarbon chain of n-ASA, with its accessible carbonyl groups, enabled a strong plasticization effect on the tested polymers. Due to the excellent mechanical properties (i.e., a tough film structure with considerable flexibility) and low permeability of the plasticized films, n-ASAs, and especially OSA proved to be an ideal plasticizer particularly for EC based coatings. Also, the EC aqueous dispersion plasticized with n-ASAs resulted in a markedly enhanced coalescence of the colloidal polymer particles, even at low drying temperatures. In applications where a coating with high flexibility is required, n-ASAs can be used as plasticizers at moderately high concentrations (up to 60-70%, w/w) without losing the high tensile strength, excellent toughness and low permeability of EC and SA films.

Controlled porosity osmotic pump-based controlled release systems of pseudoephedrine: I. Cellulose acetate as a semipermeable membrane

A controlled porosity osmotic pump-based drug delivery system has been described in this study. Unlike the elementary osmotic pump (EOP) which consists of an osmotic core with the drug surrounded by a semipermeable membrane drilled with a delivery orifice, controlled porosity of the membrane is accomplished by the use of different channeling agents in the coating. The usual dose of pseudoephedrine is 60 mg to be taken three or four times daily. It has a short plasma half life of 5–8 h. Hence, pseudoephedrine was chosen as a model drug with an aim to develop a controlled release system for a period of 12 h. Sodium bicarbonate was used as the osmogent. The effect of different ratios of drug:osmogent on the in-vitro release was studied. Cellulose acetate (CA) was used as the semipermeable membrane. Different channeling agents tried were diethylphthalate (DEP), dibutylphthalate (DBP), dibutylsebacate (DBS) and polyethyleneglycol 400 (PEG 400). The effect of polymer loading on in-vitro drug release was studied. It was found that drug release rate increased with the amount of osmogent due to the increased water uptake, and hence increased driving force for drug release. This could be retarded by the proper choice of channeling agent in order to achieve the desired zero order release profile. Also the lag time seen with tablets coated using diethylphthalate as channeling agent was reduced by using a hydrophilic plasticizer like polyethyleneglycol 400 in combination with diethylphthalate. This system was found to deliver pseudoephedrine at a zero order rate for 12 h. The effect of pH on drug release was also studied. The optimized formulations were subjected to stability studies as per ICH guidelines at different temperature and humidity conditions.

Novel bilirubin-based PVC calcium sensors.

Poly(vinyl chloride) membrane sensors for Ca(II) ions were constructed based on bilirubin (1,3,6,7-tetramethyl-4,5-dicarboxyethy-2,8-divinyl-[b-13]-dihydrobilenone) as a neutral carrier in the presence of various plasticizers (o-nitrophenyloctyl ether, dioctyl phethalate and dibutyl sebacate), which were used as solvent mediators to incorporate the carrier into the membranes. The role of plasticizers as a medium of complexation was demonstrated. The influences of an anionic excluder, the pH and foreign ions were investigated. The selectivity coefficients were measured by a separate solution method. Among the plasticizers used, o-nitrophenyloctyl ether gave the best selectivity in the presence of large concentrations of alkali and alkaline earth's metal ions. Using sensor number I, a linear calibration graph with a good Nernstian slope of 29.5 +/- 0.8 mV was obtained for Ca(II) concentrations of 5 x 10(-7)-10(-2) mol l(-1) with a detection limit of 3 x 10(-7) mol l(-1) (12 ppb). The sensor can be used for more than 3 months with good reproducibility and a fast response time of 10 s. The developed sensor has been successfully applied to the analysis of some pharmaceutical formulations, baby-food products and human plasma. Moreover, it can be used as an indicator sensor in the potentiometric titration of Ca(II) with EDTA.

Evaluation of the Film-Forming Property of Hydrogenated Rosin

The film-forming and coating properties of a new biomaterial, hydrogenated rosin (HR), is investigated in the present communication. Films produced by casting method are studied for mechanical, (tensile strength, elongation, and Young's modulus), water vapor transmission, and moisture absorption characteristics. Type of plasticizer and its concentration were observed to play an important role in modifying the film characteristics. Dibutyl sebacate (DBS), a hydrophobic plasticizer, was found to be suitable for development of flexible and smooth films. Film formulations plasticized with DBS were investigated for coating the drug layered nonpareil seeds where plasticization facilitated development of smooth and uniformly coated pellets. The increase in coat buildup, however, did not sustain the drug release significantly. The studies conclude that HR films promise utility as moisture-protective hydrophobic, film-coating materials.

Examination of sex-hormonal activity of some additives for PVDC film

Stabilizers (epoxidized linseed oil and epoxidized soybean oil) and plasticizers (acetyl tributyl citrate, diacetyl monolauryl glyceride and dibutyl sebacate) commonly used in polyvinylidene chloride (PVDC) films and extracts of such films were investigated for estrogenic and androgenic activity by means of estrogen receptor (ER) and androgen receptor (AR) competitive ligand-binding assays. Further, in in vivo experiments, ovariectomized Sprague-Dawley rats were observed for uterine wet weight change, uterine endometrium hyperplasia and vaginal mucosa cornification, following administration of each test compound or extract orally (0.5 or 500 mg/kg) or subcutaneously (0.5 or 100 mg/kg). No significant response or change was observed with any of the test compounds or extracts, either in vitro or in vivo. The results thus indicate that neither the stabilizers and plasticizers used in PVDC films, nor their extracts, exert sex-hormonal activity.

Time-Dependent Mechanical Properties of Polymeric Coatings Used in Rupturable Pulsatile Release Dosage Forms

The mechanical properties of polymer films used in pharmaceutical coatings of pulsatile drug delivery systems were evaluated in the dry and the wet state by a newly developed puncture test, which allowed the time-dependent measurement of the mechanical properties on the same film specimen. Force, puncture strength, energy at break, modulus, and strain were investigated as a function of water exposure time with respect to the type of polymer and the type and concentration of plasticizer and pore former (hydroxypropyl methylcellulose, HPMC). Eudragit® RS films were very flexible, had a high strain, and broke upon puncture with only small cracks. In contrast, ethylcellulose films were more brittle with a lower strain and showed complete film rupture. Increased amounts of the hydrophilic pore former, HPMC, resulted in a reduced puncture strength and in an increase in water uptake and weight loss of the films. The puncture strength decreased with increasing plasticizer concentration and was lower with the lipophilic dibutyl sebacate than with the hydrophilic triethyl citrate.

The formation of colonic digestible films of amylose and ethylcellulose from aqueous dispersions at temperatures below 37°C

The film forming properties of a commercial aqueous ethylcellulose dispersion (Surelease) mixed with a range of ratios of an amylose/butanol complex in the presence of a range of concentrations of a plasticiser has been studied by measuring the minimum film forming temperature (MFFT). Contrary to what was to be anticipated from the literature, it was found that an additional 4% of the plasticiser (dibutyl sebacate), normally present in the standard formulation of the ethyl cellulose dispersion, was sufficient to lower the MFFT to allow the formation of films at 35°C. This was confirmed by assessment of the glass transition temperature of free films prepared by casting and drying at 35°C by the application of dynamic mechanical analysis. This technique also demonstrated that the ethylycellulose and the amylose were not miscible. The ability of faecal slurry to digest the films formed at low temperatures was confirmed by the use of a batch fermenter. The extent of digestion was directly related to the amylose content of the films, ensuring the potential to provide films, which could function as colon specific coatings.

Polymerized rosin: novel film forming polymer for drug delivery

Polymerized rosin (PR) a novel film forming polymer is characterized and investigated in the present study for its application in drug delivery. Films were produced by a casting/solvent evaporation method from plasticizer free and plasticizer containing solutions. Films prepared from different formulations were studied for their mechanical (tensile strength, percent elongation and Young's modulus), water vapour transmission and moisture absorption characteristics. Neat PR films were slightly brittle and posed the problem of breaking during handling. Hydrophobic plasticizers, dibutyl sebacate and tributyl citrate, improved the mechanical properties of free films with both the plasticizers showing significant effects on film elongation. Release of diclofenac sodium (model drug) from coated pellets was sustained with high coating levels. Concentration of plasticizer was found to affect the release profile. PR films plasticized with hydrophobic plasticizers could therefore be used in coating processes for the design of oral sustained delivery dosage forms.

Effect of plasticizer on the dynamic surface tension and the free volume of Eudragit systems.

The purpose of the present study was to determine the changes of dynamic surface tension of aqueous Eudragit dispersions quantitatively and compare these data with the free volume of the free films formed from several dispersions of different dibutyl sebacate (DBS) concentrations. Eudragit L 30D and Eudragit RL 30D aqueous colloidal polymer dispersions and their cast free films were examined. The concentration of DBS varied in the dispersions from 0 to 20%. The dynamic surface tension of the dispersions were measured by the Du Nouy ring method while the free volume of cast films were determined by positron annihilation spectroscopy. The obtained results show that dynamic surface tension measurements indicate the white point (WP) of Eudragit dispersions by a significant standard deviation increase. This may suggest the applicability of dynamic surface tension measurements for the determination of the WP of polymeric dispersions. A decrease in the WP temperature of Eudragit dispersions with an increasing plasticizer concentration was observed up to the DBS concentration of 10% w/w. Above this concentration neither the WP of the polymer dispersion nor the free volume of the free films of the polymer were changed remarkably.

The characterization of polyvinyl butyral by thermal analysis

A range of thermal analytical techniques have been used to characterize PVB obtained from various manufacturers and recycled material recovered from glass recycling units. 13 C NMR spectroscopy was used to confirm that PVB is a random ter-polymer containing butyral and hydroxyl side groups with a small amount of acetate units. Little variation in chemical composition was observed between the grades studied. The PVB also contained between 20 and 25 wt.% of plasticizers and GC mass spectroscopy has been used to determine that the dominant plasticizer was dibutyl sebacate. A more convenient method to determining the amount present, however, was differential scanning calorimetry since PVB being an amorphous rubber its glass transition temperature, T g, varied with plasticizer content. Most recycled PVB samples had similar T g’s but these could be adjusted by addition of further amounts of dibutyl sebacate. PVB decomposed by side group elimination above 260 °C. Butyraldehyde, butenal, water, and acetic acid were the major components from these elimination reactions, but benzene and other aromatic products were observed from the decomposition of polyene residues. Below 260 °C the change in mass was attributed to plasticizer loss by the evaporation of dibutyl sebacate from the PVB matrix. It was concluded that recycled and blended grades of PVB could be re-used as a laminating agent for glass and that PVB should be recycled rather than placed in landfill.

Influence of sebacate plasticizers on the thermal behaviour of dipalmitoylphosphatidylcholine liposomes

Sebacic acid esters are a promising class of low toxicity plasticizers for PVC. They are lipophylic substances and thus, their interaction with biomembranes must be considered. DPPC liposomes in the presence of increasing amounts of dimethylsebacate (DMS), diethylsebacate (DES), dibutylsebacate (DBS) and di-(2-ethylhexyl)sebacate (DEHS) have been studied by DSC, both on heating and cooling. As a general feature, the melting point decreases and the enthalpy Δ H increases along with the half-width and asymmetry of the transition in most of the systems. The observed effects are strongly dependent on the length and the shape of the ester-chains suggesting that both polar interactions between carboxylic groups of sebacates and the polar heads of the lipids as well the hydrophobic interactions involving penetration into the bilayer are important. The effects are noticeable also in the presence of small amounts of plasticizers. In the presence of large amounts of DES and DBS, a complex structure of the transition arising from the coexistence of aggregates of different types and also the appearance of new phases were observed. The behaviour of sebacates to model biomembranes is quite different for other classes of lipophylic PVC plasticizers, such as phthalates and we explain the differences on the basis of the greater flexibility of the sebacic acid chain.

Study of novel rosin-based biomaterials for pharmaceutical coating.

The film forming and coating properties of Glycerol ester of maleic rosin (GMR) and Pentaerythritol ester of maleic rosin (PMR) were investigated. The 2 rosin-based biomaterials were initially characterized in terms of their physicochemical properties, molecular weight (Mw), and glass transition temperature (Tg). Films were produced by solvent evaporation technique on a mercury substrate. Dibutyl sebacate plasticized and nonplasticized films were characterized by mechanical (tensile zzzz strength, percentage elongation, and Young's modulus), water vapor transmission (WVT), and moisture absorption parameters. Plasticization was found to increase film elongation and decrease the Young's modulus, making the films more flexible and thereby reducing the brittleness. Poor rates of WVT and percentage moisture absorption were demonstrated by various film formulations. Diclofenac sodium-layered pellets coated with GMR and PMR film formulations showed sustained drug release for up to 10 hours. The release rate was influenced by the extent of plasticization and coating level. The results obtained in the study demonstrate the utility of novel rosin-based biomaterials for pharmaceutical coating and sustained-release drug delivery systems.

Influence of Plasticizer Type and Coat Level on Surelease® Film Properties

Two commercially available formulations of aqueous ethylcellulose dispersion differing in their plasticizer, i.e., Surelease/E-7-7050 containing dibutyl sebacate (DBS) and Surelease/E-7-7060 containing glyceryl tricaprylate/caprate (GTC), were evaluated and compared for their film properties as a function of polymeric coat level. Ibuprofen tablets were coated at 1, 2, 3, and 5% w/w levels using each Surelease formulation, and the coated tablets were evaluated for their drug release characteristics, coat reflectivity (gloss), surface texture, Brinell hardness, and elastic modulus. The drug release was dependent on the coat level and followed Hixson–Crowell cube-root model at 1% coat level. However, at ≥2% coat levels, the release from tablets coated with GTC plasticized formulation appeared to be best described by non-Fickian release mechanism and that from tablets coated with DBS plasticized formulation appeared to follow apparent zero-order release mechanism. At equal coat levels, tablets coated with GTC plasticized Surelease yielded lower drug release rates, higher reflectivity (gloss), lower surface roughness, higher Brinell hardness, and lower elastic modulus than those coated with DBS plasticized formulation. A good correlation was observed between the drug release rates and the reflectivity and surface texture of the coated tablets. The film-coats of GTC plasticized formulation were harder and more elastic than those of DBS plasticized formulation indicating better mechanical integrity.

Coating Polymer-plasticizer Interaction in Relation to the Enthalpy Relaxation of Polymer

In the course of the formulation of coated dosage forms, the selection of the suitable composition of the coating system is of great importance in respect of the final dosage form. Since the applied coating systems are multicomponent, the possible interactions between the components determine the physico-chemical stability of the formulated dosage form, the drug release process, as well as the formulation parameters. In the present study, the influence of the applied plasticizer, dibutyl sebacate on the enthalpy relaxation of casted Eudragit L 30D films was determined as a function of the plasticizer concentration. The enthalpy relaxation was recorded by DSC during the applied isothermal recovery process of Eudragit films. The obtained results indicate that enthalpy relaxation can be measured by DSC at 20 mass/mass% dibutyl sebacate concentration, which refers to the increased molecular mobility consequently to the effect of the interaction between the polymer and plasticizer.