Design Of Generation Research Articles

Performance evaluation of the FastIC readout ASIC with emphasis on Cherenkov emission in TOF-PET

Objective. The efficient usage of prompt photons like Cherenkov emission is of great interest for the design of the next generation, cost-effective, and ultra-high-sensitivity time-of-flight positron emission tomography (TOF-PET) scanners. With custom, high power consuming, readout electronics and fast digitization the prospect of sub-300 ps FWHM with PET-sized BGO crystals have been shown. However, these results are not scalable to a full system consisting of thousands of detector elements. Approach. To pave the way toward a full TOF-PET scanner, we examine the performance of the FastIC ASIC with Cherenkov-emitting scintillators (BGO), together with one of the most recent SiPM detector developments based on metal trenching from FBK. The FastIC is a highly configurable ASIC with 8 input channels, a power consumption of 12 mW ch−1 and excellent linearity on the energy measurement. To put the timing performance of the FastIC into perspective, comparison measurements with high-power consuming readout electronics are performed. Main results. We achieve a best CTR FWHM of 330 ps for 2 × 2 × 3 mm3 and 490 ps for 2 × 2 × 20 mm3 BGO crystals with the FastIC. In addition, using 20 mm long LSO:Ce:Ca crystals, CTR values of 129 ps FWHM have been measured with the FastIC, only slightly worse to the state-of-the-art of 95 ps obtained with discrete HF electronics. Significance. For the first time, the timing capability of BGO with a scalable ASIC has been evaluated. The findings underscore the potential of the FastIC ASIC in the development of cost-effective TOF-PET scanners with excellent timing characteristics.

Global band convergence design for high-performance thermoelectric power generation in Zintls.

Electronic band convergence can have a beneficial impact on thermoelectric performance, but finding the right band-converged compositions is still time-consuming. We propose a method for designing a series of compositions with simultaneous band convergence in the high-entropy YbxCa1-xMgyZn2-ySb2 material by zeroing the weighted sum of crystal-field splitting energies of the parent compounds. We found that so-designed compositions have both larger power factors and lower thermal conductivities and that one of these compositions exhibits a large thermoelectric figure of merit value in comparison with to other p-type Zintls. Our material shows high stability both thermally and temporally. We then assembled an all-Zintl single-stage module, nontoxic and free of tellurium, that demonstrates an exceptional heat-to-electricity conversion efficiency exceeding 10% at a temperature difference of 475 kelvin.

Bivalent and bitopic ligands of the opioid receptors: The prospects of a dual approach.

Opioid receptors belonging to the class A G-protein coupled receptors (GPCRs) are the targets of choice in the treatment of acute and chronic pain. However, their on-target side effects such as respiratory depression, tolerance and addiction have led to the advent of the 'opioid crisis'. In the search for safer analgesics, bivalent and more recently, bitopic ligands have emerged as valuable tool compounds to probe these receptors. The activity of bivalent and bitopic ligands rely greatly on the allosteric nature of the GPCRs. Bivalent ligands consist of two pharmacophores, each binding to the individual orthosteric binding site (OBS) of the monomers within a dimer. Bitopic or dualsteric ligands bridge the gap between the OBS and the spatially distinct, less conserved allosteric binding site (ABS) through the simultaneous occupation of these two sites. Bivalent and bitopic ligands stabilize distinct conformations of the receptors which ultimately translates into unique signalling and pharmacological profiles. Some of the interesting properties shown by these ligands include improved affinity and/or efficacy, subtype and/or functional selectivity and reduced side effects. This review aims at providing an overview of some of the bivalent and bitopic ligands of the opioid receptors and, their pharmacology in the hope of inspiring the design and discovery of the next generation of opioid analgesics.

Renewable energy storage using hydrogen produced from seawater membrane-less electrolysis powered by triboelectric nanogenerators

Utilization of widely available seawater for hydrogen generation using robust electrolysis methods can provide sustainable solutions to energy carriers. Sea waves at the same time provide abundant renewable energy that can produce the electricity required for seawater electrolysis. This work presents a novel design for a self-powered hydrogen generation based on membrane-less seawater electrolysis integrated with spring-assisted spherical triboelectric nanogenerators. To streamline fabrication and minimize maintenance expenses, water electrolysis is conducted in a membrane-less electrochemical cell reactor. Employing a mathematical model, the system's performance is analyzed across different catalysts, electrolytes, and operational temperatures. The modeling outcomes indicate that elevating the cell's temperature can lower the necessary potential, enhancing overall electrochemical cell efficiency and decreasing capacitor charging duration. The voltage required for the cell to reach 100 mA cm−2 in the seawater decreases from 2.4 V to 1.9 V as the cell temperature increase from 25 °C to 70 °C. This is due to the decline in the hydrogen and oxygen evolution reaction overpotentials for NPNNS and Ti supported PtPd from 351 mV to 246 mV and 568 mV–394 mV, respectively. Furthermore, increase in the temperature results in an additional 19 % improvement in cell efficiency from 78 % to 97 % and producing hydrogen per cycle during electrolysis of seawater increase from 0.015 μmole to 0.020 μmole.

Polymers of intrinsic microporosity with alkaline pyrrolidine and piperidine functional groups for high-temperature proton exchange membranes

Recently, the polymers of intrinsic microporosity (PIMs) exhibit good potential in high-temperature proton exchange membrane fuel cells (HT-PEMFCs) due to their tunable microporosity and functionality. In this paper, alkaline pyrrolidine and piperidine functional groups were introduced onto PIM-1 via the classical Mannich reaction obtaining PIM-1/PIM-Py-50 and PIM-1/PIM-MePi-50. It was found that, compared with commercial Meta-polybenzimidazole (m-PBI) membrane, PIMs membranes showed superior retention of phosphoric acid (PA) and conductivity due to their grafting alkaline groups and rich micropores. After equilibration under 80 °C/40 % relative humidity (RH) for 150 h, the PA retention of PA doped PIM-1/PIM-Py-50 (PIM-1/PIM-Py-50/PA) and PA doped PIM-1/PIM-MePi-50 (PIM-1/PIM-MePi-50/PA) membranes were 74.13 % and 68.52 %, respectively, much higher than PA doped m-PBI (m-PBI/PA) (45.73 %). PIMs membranes maintain excellent dimensional and conductivity stability at 160 °C operating conditions, e.g. PIM-1/PIM-Py-50/PA membrane showed area swelling retention and volume swelling retention of 84.69 % and 82.19 % after 230 h at 160 °C. In addition, with the similar PA uptake, PIMs membranes displayed higher conductivity and peak power density (PPD) at 160 °C. In the accelerated stress test (AST) the PPD of the fuel cell (FC) with the PIM-1/PIM-Py-50/PA membrane remained 81.25 % after 200 aggressive start-up/shut-down cycles at 80 °C. Therefore, PIM-based membranes alkaline groups exhibit a wider temperature operating window, providing theoretical guidance for the design and study of the next generation of high-temperature proton exchange membranes (HT-PEMs).

Advanced multimaterial shape optimization methods as applied to advanced manufacturing of wind turbine generators

AbstractCurrently, many utility‐scale wind turbine generator original equipment manufacturers are dependent on imported rare earth permanent magnets, which are susceptible to market risks from cost instability. To lower the production costs of these generators and stay competitive in the market, several small wind manufacturers are pursuing continuous improvements to both generator design and manufacturing. However, traditional design and manufacturing methods have yielded marginal improvements in wind power performance. This work presents novel methods to redesign a baseline 15‐kW wind turbine generator with reduced rare‐earth permanent magnets by leveraging cutting‐edge three‐dimensional (3D) printed polymer‐bonded permanent magnets and steel. Symmetric, asymmetric, and multimaterial‐magnet parametrization methods are introduced for shape optimization. We extend the symmetric and asymmetric methods to the back iron in the stator to further investigate the impact and opportunities for performance improvements with lesser active materials. We employ a design‐of‐experiments approach with parametric computer‐aided design for shape generation and evaluate different designs by magneto‐thermal modeling and finite‐element analysis. We use adaptive sampling technique to identify better performing designs with lesser magnet mass, higher efficiency, and lower cogging torque when compared with the baseline generator. Asymmetric pole designs resulted in a magnet mass in the range of 4.77–5.37 kg, which was 27%–35% lighter than the baseline generator, suggesting that a new design freedom exists that can be enabled by advanced manufacturing, such as 3D printing. Shaping the back iron in the stator resulted in material savings in electrical steel of up to 14.62 kg, which was 20% lighter than the baseline stator. We conducted a structural analysis to evaluate an optimized asymmetric rotor design from the point of view of mechanical integrity and air‐gap stiffness. The magnetically optimal shape profile was shown as having a positive impact on the radial stiffness, and an optimal solution was discovered to reduce the structural mass by nearly 30 kg, which was 29% lighter than the baseline.

Achieving solar-thermal driven dual functional device utilizing flexible PDA coated sponge integrated thermoelectric module design for water purification and power generation

The design of an efficient solar energy collector for solar-thermal-driven water purification and power generation is a promising strategy to concurrently mitigate the shortage of fresh water and energy crises. However, harvesting low-grade thermal energy in an eco-friendly and cost-effective manner through solar-thermal materials for water evaporation and electric cogeneration remains challenging. Herein, we demonstrate a dual-functional device integrating solar-thermally driven water purification and thermo-induced power generation. This typical design, fabricated via polydopamine (PDA) tightly deposited onto melamine sponges (PDA@Sponge) via H-bonds, along with a thermoelectric generator (PDA@Sponge/TEG), showcases superior solar-thermal-driven dual-functional application. The critically structurally adjustable PDA@Sponge possesses excellent homogeneity and stability, weakening interfacial hydrogen bonding between water molecules, favoring the evaporation and overflow of water molecules. The optimal serrated design achieves a water evaporation rate of up to ∼1.50 kg −2h−1, with an efficiency of ∼ 94.04 % under one sun, surpassing the most of previous reports, owing to its special tip thermal localization effect and rational water transportation management. Simultaneously, the designed PDA@Sponge/TEG yields an open-circuit voltage and short circuit current of 55 mV and 22 mA, respectively, along with a maximal output power of 162 μW (40.5 μW/cm2) at a load resistance of 7.5 Ω, under one sun and room temperature. Notably, such a device, after multiple series connections, can charge a capacitor to 1.5 V within 1 min, capable of powering low-energy electronic devices such as smartwatches and LED lights. By efficiently integrating of multiple solar-thermal-driven processes, our research promotes the design of multifunctional devices to promise an approach for desalinating seawater, purifying wastewater, and powering low-energy electronics, especially in remote areas lacking power stations and/or water treatment facilities.

Corrosion kinetics of T91 steel under low oxygen conditions (10−7 wt% O) in lead-bismuth eutectic at 500 °C

Among the advanced reactor designs of the fourth generation, the Lead-cooled Fast Reactor (LFR) stands out as one of six distinct types. The corrosion caused by the liquid Lead-Bismuth Eutectic (LBE) on structural materials is recognized as a significant obstacle hindering the development of LFR. The corrosion kinetics of T91 steel in static LBE with 10−7 wt% oxygen at 500 ºC is analyzed in this study. The formed oxide scale consists of an outer (Fe, Cr)3O4 layer with a Fe-Cr spinel structure and an inner internal oxidation zone (IOZ). The thickness evolution of the oxide layers follows a parabolic rule, with rate constants determined for different layers. The dissolution rate of metals into the LBE decreases over time, indicating diminishing the concentration gradient of Fe across the oxide layer-LBE interface. The observed deviations from expected norms may be attributed to dynamic flow conditions and non-isothermal loop experiments, which accelerate Fe diffusion into LBE.

Low tortuous permeable concrete pavement material: A new approach to improve physical properties

Permeable pavement is an environmentally beneficial material that can ease urban problems and mitigate the effects of climate change, such as flooding, urban heat islands, and groundwater decrease. However, it is susceptible to clogging, has limited strength, and demands frequent maintenance. To overcome these problems, an untraditional fiber-reinforced permeable pavement with a low tortuosity pore structure that has an excellent infiltration rate and strength while being resistant to clogging has been studied in this research. Straight pore channels of various sizes and quantities were introduced into self-compacting concrete to create this permeable pavement. High-strength pervious pavement (HSP) samples with porosity ranging from 3.60 to 8.30% and 0–0.2% fiber content were tested. In all cases, HSP showed high infiltration rate (>1 cm/s), high compressive strength (>27 MPa) and tensile strength (1.5 MPa), low mass loss in potential resistance to degradation by impact and abrasion (>25%). However, it did not clog despite extensive cyclic exposure to flow containing sand, clay, and combined ‘sand & clay’. PP fiber content of 0.1%. The 3.60% porosity was found to be optimum considering all properties, whereas 8.30% porosity gave a higher infiltration rate with compromised properties. This permeable pavement can maintain sufficient porosity and permeability for stormwater infiltration without frequent maintenance. Adding polypropylene fiber reduces compressive strength marginally but increases split tensile strength, degradation and potential resistance. This novel fiber-reinforced HSP has the potential to expand the material's applicability. The results obtained from this research are expected to lead the way for a broader application of HSP in various contexts and initiatives that were not previously considered appropriate. This will eventually enhance the design and implementation of a new generation of flood-resistant infrastructure and significantly improve the ability to mitigate urban floods.

Designing product upgrades in the presence of online consumer reviews

AbstractWhen consumers decide whether to buy an experience good, they usually search for online reviews to reduce quality uncertainty. In this paper, we consider that consumers may strategically wait for the new generation product and consult reviews of the previous generation product in the same series while facing sequential launching products. We develop a two‐period analytical model analyzing how the presence of intergenerational reviews influences the firm's decision on product upgrades. Our analysis obtains three main findings. First, when online reviews are less efficient and consumers are more strategic, the firm should skip the old product due to the severe product cannibalization effect. Second, negative reviews discourage the firm from quality improvement, and positive reviews drive the firm to provide quality improvement at a high price. Third, the firm chooses a decreasing price path without online reviews. However, an increasing price path is preferred in the presence of online reviews when online reviews are positive, the efficiency of consumer reviews is high, and consumers are more strategic. Our study indicates that online reviews have important influence on product generation design, and the firm should carefully evaluate online reviews of the old product when designing its new generation product.

Nonlocal quasi-3d vibration/ analysis of three-layer nanoplate surrounded by Orthotropic Visco-Pasternak foundation by considering surface effects and neutral surface concept

The present article deals with the application of refined plate theory and surface effects to investigate the nonlocal free vibration behavior of a functionally graded nano-plate composed of two piezoelectric face sheets resting on Orthotropic Visco-Pasternak. Surface and nonlocal effects are applied using the surface piezoelectricity and stress-strain gradient theories. Surface effects, refined quasi-3D higher-order theory, neutral surface position and in-plane mechanical preloads are considered to study piezoelectric sandwich nano-plate with a functionally graded core in this study for the first time, simultaneously. The size-dependent governing equations are derived based on 2D and 3D refined theory using Hamilton’s principle and different boundary conditions are studied and investigated according to the semi-analytical solution method. Comparing the results of the vibration behavior of 2D and quasi-3D models, local and non-local models, and also, examining different foundations simultaneously can be said as one of the innovations of the current research. Finally, a parametric study is presented to examine the effects of different parameters such as surface effects, small scale parameters, mechanical preloads, thickness stretching effects, neutral surface position, non-homogeneous coefficient, applied voltage, different foundation constants, boundary conditions, geometrical ratios and different theories in details. It is indicated that the inclusion of surface effects and thickness stretching effects leads to a significant influence on the vibration behavior of three-layered nano-scale plates. The presented results in this article may provide useful guidance for the design and development of the next generation of nano-devices.

Comparison of impulse noise energy distribution from two generations of parachute gun

The rocket ejection seat is an advanced life-saving device for fighter pilots. However, it can also produce damaging impulse noise during ejection, which could compromise the pilot’s hearing health, and the manufacturer must assess the noise damage. This study uses Variational Mode Decomposition (VMD) and Hilbert-Huang transform (HHT) to analyze energy-instantaneous distribution over time and frequency-instantaneous and energy contribution of different modes of impulse noise generated by the parachute gun in two generations of rocket ejection seats. The results demonstrate considerable disparities in the energy distribution of impulse noise generated by the parachute gun in the new generation seat compared to the old generation seat. The new generation seat has higher overall energy, more concentrated action time, and a higher energy contribution in the 1-10 kHz frequency range. These findings provide valuable data for the design of the new generation of noise protection equipment for pilots.

Quaternary Ammonium Compounds and Their Composites in Antimicrobial Applications

AbstractQuaternary ammonium compounds (QACs) are well‐known for their antimicrobial properties, but their widespread use is limited due to suboptimal antimicrobial efficiency and safety concerns. Recent progress in materials science has paved the way for the development of QAC‐based composites (QACCs). QACCs with diverse compositions have shown enhanced antimicrobial effectiveness and biosafety for various applications, such as food packaging, capacitive deionization, and household antimicrobials. This review provides a comprehensive summary of the synthesis approaches and different types of QACCs. Moreover, this review examines their antimicrobial applications, taking the underlying structure‐activity relationship into consideration. In addition, this perspectives are presented on the remaining challenges and future research directions for the further development of QACCs. It is expected that this review will provide a valuable reference for the design of next generation QACC‐based antimicrobial agents.

Mechanical characterization of soft-tissue stiffness during mandibular distraction

The purpose of this study was to determine the stiffness of mandibular soft tissues during mandibular distraction, from the perspective of improving distraction devices such as automated continuous distractors.Uncompleted osteotomy was performed on 11 fresh human hemimandibles via a greenstick fracture, to preserve the uplift of the internal periosteum of the mandibular corpus. In order to replicate continuous distraction, direct measurements were performed through a uniaxial quasi-static tensile test. For all specimens, linear regression was applied to the force-displacement curve for a force region of 10–20 N, and the slope extracted. The mean stiffness was estimated to be 9.12 ± 3.56 N/mm.This study is the first to measure directly the stiffness of the surrounding tissues of the human mandibular corpus, and paves the way to the design of a new generation of distractor devices.

Anion substitution-induced CuCoSe hollow nanotubes as multifunctional electrode materials for supercapacitors and overall water splitting

Developing highly efficient non-noble-metal electrode materials for energy storage and conversion is crucial for advancing sustainable and renewable energy. In this study, a facile and effective anion substitution-induced approach was designed to synthesize uniform CuCoSe hollow nanotubes. Impressively, the obtained CuCoSe hollow nanotubes reach an exceptional mass-specific capacitance of 2,853.1F·g−1 at 10 A·g−1, with intriguing rate capability and desirable capacitance retention after 5,000 cycles. The assembled CuCoSe//CuCoSe symmetrical supercapacitor device exhibits a high energy density of 218.9 Wh·kg−1 at a power density of 4,000 kW·kg−1. Furthermore, the CuCoSe hollow nanotubes show exceptional performances in both oxygen and hydrogen evolution reactions, necessitating low overpotentials of 94.4 and 33.4 mV at 10 mA·cm−2. When used as a bifunctional electrocatalyst, the assembled CuCoSe||CuCoSe electrolytic cell affords a low cell voltage of 1.40 V to drive 10 mA·cm−2, significantly superior to other commercial electrolyzers and most reported bifunctional electrocatalysts. Experimental and density functional theory calculations suggest that selenides substituted CuCo-layered double hydroxides can greatly enhance the electrochemical performances. This work will be beneficial for the design of the next generation of energy storage and conversion technologies.

Antifouling macrocyclic-engineered PVDF membrane for the low-pressure separation of surfactant-stabilized oily wastewater

Fouling is a common phenomenon which affects the long-term efficacy of membranes in the practical treatment of oily wastewater. It often results in a dramatic decline in flux, and a consequent increase in maintenance and operational cost. To address this, various substrates have been incorporated during membrane fabrication to enhance the fouling resistance, and improve the separation efficiency. Herein, we report the fabrication of a novel symmetrical ball-copper phthalocyanine incorporated PVDF membrane (CuPc@PVDF) for the effective separation of surfactant-stabilized oil-in-water emulsions. The symmetrical ball-Cu phthalocyanine with four non-peripheral substituents synthesized ab-initio and characterized using UV–vis, FT-IR, 1H NMR, and MALDI-TOF spectroscopies was added to the casting solution during membrane fabrication resulting in the formation of highly hydrophilic and anti-fouling CuPc@PVDF membrane. In contrast to the PVDF membrane, having a water contact angle of 82.3° ± 0.7°, the CuPc@PVDF membrane demonstrated high hydrophilicity with a contact angle of 55.5° ± 0.5°, and pure water permeance up to 768 LMH at 3 bar. It further achieved 99.9 % rejection of oil with size in the range of 50–450 nm at 1 bar, and demonstrated high stability and excellent anti-fouling property during 10 cycles of continuous demulsification, with a flux recovery ratio (FRR) of 98.5 %, and extremely low irreversible flux of 1.5 %. Similarly, the CuPc@PVDF membrane exhibited high resistance to accelerated organic fouling, maintaining a steady flux and an FRR of 93.0 % during 1 hour of continuous operation with 10 ppm sodium alginate and Ca2+ ions. This study reports a novel strategy to enhance the fouling resistance of demulsification membranes, and could be further explored in the design of next generation of advanced membranes for the purification of oily wastewater.

Inclined solar interface evaporation system with downward steam generation for efficient desalination and salt crystallization positioning

Solar-driven Interfacial Vapor Generation (SIVG) has been recognized as a potentially effective method of converting seawater into potable freshwater resources. In this work, we employed a straightforward approach to cultivate CuS and polypyrrole on copper foam as an solar absorber, while sterilized face towels served as water an evaporation interface and water transport sites. An inclined steam blocking evaporator with a salt-out part that attracts salt aggregation was ingeniously designed to improve the salt-resistant performance. Even in 15 wt% brine, the evaporation equipment maintained a stable and high evaporation rate, with an average evaporation rate of about 1.588 kg m−2 h−1 under 1 solar illumination. More particularly, in order to improve the water collection rate, a beveled condensers placed at the bottom of the steam blocking evaporator was customized, so as to shorten the steam condensation path and achieve internal water collection. Therefore, the water collection rate of the evaporator is as high as 2.238 kg m−2 h−1 and water collection efficiency is 85.90 %. Additionally, the evaporation device can effectively purify heavy metal ions and organic matter. This study can provide a new idea for the design and performance improvement of solar interfacial vapor generation and water collection device.

Investigations on the development of impact-resistant thermoplastic fibre hybrid composites from glass and steel fibre

With the increased use of fibre reinforced composites (FRP), the design of new generation of composite structures with high stiffness and a ductile material behaviour is required to cope with complex load scenarios and high damage tolerances. This can be achieved, in particular, by a combination of conventional fibre-reinforced composites (FRP), which possess high stiffness and strength with metallic materials characterized by their high ductility and associated higher energy absorption capacity. Currently, there are no solutions for hybridisation of high performance filament yarns, metal filament yarns and thermoplastic filament yarns on micro level. Therefore, the main objective of this study is to develop a fibre hybrid composite based on hybrid yarn consisting of glass, steel and polypropylene filament yarns and to compare its tensile and impact properties with those of the composite reinforced only with glass filament yarn. The tensile and impact properties of the unidirectional hybrid composites produced from the developed multi-material hybrid yarn consisting of steel, glass and polypropylene filament yarns are compared with those of a non-hybrid composite reinforced exclusively with glass filament yarn. The results show that by hybridising with steel fibres a characteristic post-failure behaviour can be achieved, so that the developed multi-material hybrid yarns have a high potential for use in composites with high crash and impact performance requirements, where safety demands are essential.

3D Printing of Double Network Granular Elastomers with Locally Varying Mechanical Properties.

Fast advances in the design of soft actuators and robots demand for new soft materials whose mechanical properties can be changed over short length scales. Elastomers can be formulated as highly stretchable or rather stiff materials and hence, are attractive for these applications. They are most frequently cast such that their composition cannot be changed over short length scales. A method that allows to locally change the composition of elastomers on hundreds of micrometer lengths scales is direct ink writing (DIW). Unfortunately, in the absence of rheomodifiers, most elastomer precursors cannot be printed through DIW. Here, 3D printable double network granular elastomers (DNGEs) whose ultimate tensile strain and stiffness can be varied over an unprecedented range are introduced. The 3D printability of these materials is leveraged to produce an elastomer finger containing rigid bones that are surrounded by a soft skin. Similarly, the rheological properties of the microparticle-based precursors are leveraged to cast elastomer slabs with locally varying stiffnesses that deform and twist in a predefined fashion. These DNGEs are foreseen to open up new avenues in the design of the next generation of smart wearables, strain sensors, prosthesis, soft actuators, and robots.

Three-Dimensionally Nanometallic Superstructure Synthesized via a Single-Particle Soft-Enveloping Strategy.

Three-dimensionally (3D) integrated metallic nanomaterials composed of two or more different types of nanostructures make up a class of advanced materials due to the multidimensional and synergistic effects between different components. However, designing and synthesizing intricate, well-defined metallic 3D nanomaterials remain great challenges. Here, a novel single-particle soft-enveloping strategy using a core-shell Au NP@mSiO2 particle as a template was proposed to synthesize 3D nanomaterials, namely, a Au nanoparticle@center-radial nanorod-Au-Pt nanoparticle (Au NP@NR-NP-Pt NP) superstructure. Taking advantage of the excellent plasmonic properties of Au NP@NR-NP by the synergistic plasmonic coupling of the outer Au NPs and inner Au nanorods, we can enhance the catalytic performance for 4-nitrophenol hydrogenation using Au NP@NR-NP-Pt NP as a photocatalyst with plasmon-excited hot electrons from Au NP@NR-NP under light irradiation, which is 2.76 times higher than in the dark. This process opens a door for the design of a new generation of 3D metallic nanomaterials for different fields.