Degradation Of Methyl Orange Research Articles

Controllable preparation of YPrO3 photocatalystvia sol-gel method with enhanced photocatalytic performance under ultraviolet light

In this work, an ultraviolet light-driven YPrO3 photocatalyst was successfully synthesized via the sol-gel method, utilizing yttrium nitrate hexahydrate (Y(NO3)3·6H2O) and praseodymium nitrate hexahydrate (Pr(NO3)3·6H2O) as the yttrium and praseodymium sources, respectively, with oxalic acid dihydrate (H2C2O4·2H2O) serving as an auxiliary solvent. In addition, the prepared samples were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy(XPS), thermogravimetric and differential scanning calorimetry (TG-DSC), ultraviolet visible diffuse reflectance spectroscopy (UV VisDRS), and an electrochemical workstation. Also, the photocatalytic activity of YPrO3 samples was explored by using methyl orange (MO) solutionas a model pollutant to simulate wastewater under varying synthesis temperatures and illumination durations. The material with the highest degradation efficiency was subjected to cycling and recovery experiments to assess its stability. Furthermore, the photocatalytic mechanism of YPrO3 was investigated. Experimental results revealed that pure YPrO3 samples could be effectively synthesized at calcination temperatures ranging from 850 °C to 1000 °C, with the sample prepared at 900 °C exhibiting the optimal photocatalytic activity. This sample possessed an average grain size of 4–5 μm. Under UV light irradiation for 90min, the YPrO3 sampleprepared at 900°Cachieved approximately 80 % degradation of methyl orange at an initial concentration of 5 mg/L. After five consecutive cycles, the degradation rate remained as high as 70.39 %, with no change in the crystal structure, indicating excellent stability. The photocatalytic mechanism of YPrO3 was found to involve the synergetic effect of superoxide radicals and photogenerated holes in degrading pollutants. In conclusion, YPrO3could be a promising photocatalyst with excellent performance, holding broad application prospects.

Mechanism and toxicity assessment of Cu0/Fe3O4 activated persulfate based on the acceleration cycle of Fe3+/Fe2+ for the degradation of methyl orange

Accelerating the circulation of Fe3+/Fe2+ contributed to the production of SO4·- during persulfate activation in the treatment of refractory wastewater. In this study, magnetic Cu0/Fe3O4 was prepared to enhance the Fe3+/Fe2+ circulation and the separation of Cu0/Fe3O4. The composition, structure, catalytic activity and toxicity of Cu0/Fe3O4 were investigated. The degradation mechanisms of MO were investigated, as well as the toxicity of MO and the breakdown products were evaluated. The results showed that Cu0/Fe3O4(1:3) was more efficient for PS activation as compared with single Cu0 or single Fe3O4. Removal efficiency of MO was up to 94.2% and ·OH and 1O2 played the dominant role. Cu0 and in-situ generated Cu+ accelerated the circulation of Fe3+/Fe2+ and electron transfer efficiency from Cu0/Fe3O4(1:3) to PS. MO molecule was effectively decomposed through hydroxylation and the cleavage of NC and NN bonds. The leachate toxicity of Cu0/Fe3O4(1:3) was low, and the toxicity of intermediate products produced during the reaction was significantly less than MO. In conclusion, this study proposed a feasible pathway for rapid cycle of Fe3+/Fe2+ on the Fe3O4 surface and separation of Cu0 by using Cu0/Fe3O4 as a promising activator for PS, effectively improving the degradation efficiency of MO.

Enhanced photocatalysis by defect-engineered CeO2 with sulfite activation under visible light irradiation

Sulfite-based advanced oxidation processes (s-AOPs) have recently garnered significant attention due to their ability to generate highly oxidative sulfate radicals and eliminate contaminants from water. A state-of-the-art platform has been developed through the synergistic combination of s-AOP and photocatalysis under visible light as weak as ambient indoor daylight. This platform achieved an enhanced degradation efficiency for defect-engineered CeO2 nanocubes by using sodium sulfite instead of SO2, resulting in a synergy factor of up to 88%. The reaction pathways, intermediates, ion leaching and the possible influence of aqueous conditions during the methyl orange degradation have been investigated. The CeO2/Na2SO3/vis-light platform exhibits promising prospect as a system to enhance conventional s-AOP in wastewater treatment or disinfection. It demonstrates excellent performance in terms of pH sensitivity, anion influence, and resistance to leaching. This highlights its significant potential for practical applications and future process scale-up.

Photocatalytically active layered double hydroxide-PVDF composite membranes for effective remediation of dyes contaminated water

In this work, polyvinylidene fluoride (PVDF) intercalated CuFe layered double hydroxides (LDH) membranes were fabricated and investigated for UV-LED/persulfate degradation of methylene blue (MB), crystal violet (CV), methyl orange (MO), and Eriochrome black T (EBT) dyes from water. The PVDF-CuFe membrane exhibited improved heterogeneity, surface functionality (CuO, Fe–O, Cu–O–Fe), surface roughness, and hydrophilicity. The process parameters were optimized by response surface methodology, and maximum MB removal (100%) was achieved within 45.22–178.5 min at MB concentration (29.45–101.93 mg/L), PP concentration (0.5–2.41 g/L) and catalyst dosage (1.84–1.95 g/L). The degradation kinetics was well described by a pseudo-first-order model (R2 = 0.982) and fast reaction rate (0.029–0.089/min). The MB dye degradation mechanism is associated with HO·/SO4•− reactive species generated by Fe3+/Fe2+ or Cu2+/Cu+ in PVDF-CuFe membrane and PP dissociation. The PVDF-CuFe membrane demonstrated excellent recyclability performance with a 12% reduction after five consecutive cycles. The catalytic membrane showed excellent photocatalytic degradation of crystal violet (100%), methyl orange (79%), and Eriochrome black T (60%). The results showed that UV-LED/persulfate-assisted PVDF-CuFe membranes can be used as a recyclable catalyst for the effective degradation of dye-contaminated water streams.

Functionalization of Polypropylene by TiO2 Photocatalytic Nanoparticles: On the Importance of the Surface Oxygen Plasma Treatment.

A new two-step method for developing a nanocomposite of polypropylene (PP) decorated with photocatalytically active TiO2 nanoparticles (nTiO2) is proposed. This method involves the low-temperature plasma functionalization of polypropylene followed by the ultrasound-assisted anchoring of nTiO2. The nanoparticles, polymeric substrate, and resultant nanocomposite were thoroughly characterized using nanoparticle tracking analysis (NTA), microscopic observations (SEM, TEM, and EDX), spectroscopic investigations (XPS and FTIR), thermogravimetric analysis (TG/DTA), and water contact angle (WCA) measurements. The photocatalytic activity of the nanocomposites was evaluated through the degradation of methyl orange. The individual TiO2 nanoparticles ranged from 2 to 6 nm in size. The oxygen plasma treatment of PP generated surface functional groups (mainly -OH and -C=O), transforming the surface from hydrophobic to hydrophilic, which facilitated the efficient deposition of nTiO2. Optimized plasma treatment and sonochemical deposition parameters resulted in an active photocatalytic nTiO2/PP system, degrading 80% of the methyl orange under UVA irradiation in 200 min. The proposed approach is considered versatile for the functionalization of polymeric materials with photoactive nanoparticles and, in a broader perspective, can be utilized for the fabrication of self-cleaning surfaces.

Enhanced Photocatalytic Degradation of Methyl Orange by Metal‐Tio2 Nanoparticles

AbstractIn this study, a series of transition metal‐doped TiO2 was prepared by a simple sol‐solvothermal method. Mix an ethanol solution of tetrabutyl titanate and metal nitrate solution to obtain a homogeneous sol, which is then subjected to solvothermal treatment. After calcination, the metal‐TiO2 naoncomposite was obtained. Selected transition metal precursors, including Cu, Fe, Ag, Cr, Co and Zn, were doped into TiO2 nanocatalysts to assess photocatalytic degradation activities. The results show that 1 mol % Ag−TiO2 photocatalyst has a larger specific surface area, a stable anatase phase and the narrowest forbidden band energy (3.00 eV). In photocatalytic degradation of methyl orange (MO) tests, 1 mol % Ag−TiO2 could reach 100 % decolourisation after 70 min and 75.43 % mineralisation after 90 min. ESR analysis confirmed that Ag doping significantly increased the content of ⋅O2− and ⋅OH for the TiO2 catalyst, which are responsible for the oxidation reactions and consequently degradation of pollutants. The photocatalytic degradation mechanism of MO was also proposed. The TOC analyses confirmed the mineralization of MO. The excellent thermal and chemical stability of 1 mol % Ag−TiO2 has also been demonstrated by thermogravimetric analysis and cycling experiments. Electrochemical tests have also demonstrated the excellent electrochemical properties of 1 mol % Ag−TiO2.

Valorization of ladle furnace slag and functional enhancement of post-adsorption materials

Carbonating metallurgical slags plays a pivotal role in achieving efficient mineral CO2 sequestration and waste valorization.This research introduces a novel integrated approach that combines the carbonation of Ladle Furnace Slag (LFS) with the simultaneous degradation of Methyl Orange (MO) in synthetic water. The comprehensive characterization of LFS was conducted using X-ray Diffraction (XRD), X-ray Fluorescence (XRF), Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES), Brunauer-Emmett-Teller (BET) analysis, and Scanning Electron Microscopy (SEM). The adsorption experiments reveal the high LSF capacity for MO degradation (149.25 mg/g) following pseudo-second-order kinetics (R2 = 0.99) and Langmuir isotherm (R2 = 0.98). The adsorption process was primarily governed by chemical and electrostatic interactions. Analysis of LFS-loaded MO indicated a reduction in Ca(OH)2phases, responsible for CO2mineralization and the formation of calcite (CaCO3). Furthermore, the study explored the reusability of LFS-MO composites through chemical and thermal modifications. Pyrolysis of carbonated LFS with KOH impregnation exhibited potential for regenerating Ca(OH)2phases, while thermal modification induced significant mineral and microstructural changes, creating new active sites at various temperatures. Additionally, the Fenton-like reaction followed by thermal modification resulted in a highly organized and microporous LFS structure with enhanced surface area and porosity. Moreover, modification with ZnSO4followed by thermal activation promoted the formation of ZnO nanoxides on the LFS surface. This research proposes an innovative carbonating approach for metallurgical slags and wastewater treatment, extending their utility and enhancing industrial sustainability. Carbonated LFS-MO composites hold promise for applications in construction, CO2capture, and wastewater treatment, thereby fostering sustainable industrial practices with ongoing research and development efforts.

Surprising Effects of Al2O3 Coating on Tribocatalytic Degradation of Organic Dyes by CdS Nanoparticles

With a band gap of 2.4 eV, CdS has been extensively explored for photocatalytic applications under visible light irradiation. In this study, CdS nanoparticles have been investigated for the tribocatalytic degradation of concentrated Rhodamine B (RhB) and methyl orange (MO) solutions. For CdS nanoparticles in a glass beaker, 78.9% of 50 mg/L RhB and 69.8% of 20 mg/L MO solutions were degraded after 8 h and 24 h of magnetic stirring using Teflon magnetic rotary disks, respectively. While for CdS nanoparticles in a beaker with Al2O3 coated on its bottom, 99.8% of the RhB solution was degraded after 8 h of magnetic stirring and 95.6% of the MO solution was degraded after 12 h of magnetic stirring. Moreover, another contrast was observed between the two beaker bottoms—a new peak at 250 nm in UV–visible absorption spectra was only observed for the MO degradation by CdS in the as-received glass beaker, which indicates that MO molecules were only broken into smaller organic molecules in that case. These findings are meaningful for expanding the catalytic applications of CdS and for achieving a better understanding of tribocatalysis as well.

Bio‐Fabricated Silver Nanoparticles for Catalytic Degradation of Toxic Dyes and Colorimetric Sensing of Hg2+

AbstractIn the present study, silver nanoparticles were synthesized via green synthesis using fenugreek (Trigonella foenum‐graecum L.) seeds of variety HM 425. The AgNPs were characterized by using UV‐Visible spectroscopy, Particle size analyzer, Field emission scanning electron microscopy coupled to Energy dispersive X‐ray spectroscopy, XRD, High resolution transmission electron microscopy and Fourier Transform Infrared Spectroscopy. The AgNPs were spherical and had an average particle size of 28 nm. The reduction of cationic dyes Methylene blue, Rhodamine B, and an anionic azo dye Methyl Orange by Sodium borohydride was used as a model reaction to investigate the catalytic ability of AgNPs. The results demonstrated an efficient catalytic dye degradation of methylene blue (95.81 %, 25 min, 0.1737±0.01 min−1), Rhodamine B (90.23 %, 15 min, 0.1388±0.01 min−1) and methyl orange (83.63 %, 39 min, 0.0412±0.002 min−1). The synthesized AgNPs had an excellent detection limit of 12.50 μM for Hg2+, making them excellent solid bio‐based sensors for mercury sensing.

Enhanced sunlight-driven photocatalysis of non-metal doped zinc oxide via wet impregnation for the removal of organic compounds

Zinc oxide (ZnO), a commonly used photocatalyst, suffers from the rapid recombination of photogenerated charge carriers, and the inability to harvest visible light. Therefore, the green synthesized ZnO from Garcinia mangostana pericarp is modified via non-metal (X) doping of N, P, S, Br, and B with a mass content of 5 % to tackle the aforementioned. The obtained materials were characterized through various modern characterization techniques. The results reveal that amongst the X-doped sample, ZnO-B demonstrates the highest photocatalytic performance. The characteristics of ZnO include good crystallinity as well as a low band gap energy of 2.094 eV, revealing an enhanced visible light absorption activity of the sample. The photoactivity of surveyed ZnO-B was investigated through the degradation of malachite green, methyl orange, and tetracycline, achieving a removal rate of 96.29, 86.59, and 90.32 %, respectively. Simultaneously, the antibacterial properties of the ZnO-X were evaluated for Staphylococcus aureus under sunlight illumination. Moreover, the photocatalysis mechanism of the studied materials was elucidated through the band structure, toxicity, and total organic carbon removal of the post-catalysis solution. The selected boron-doped zinc oxide catalyst also showed excellent reusability after 10 cycles of photocatalysis, retaining ∼ 80 % of its original activity. The obtained results reveal the potential application of non-metal-doped zinc oxide in environmental remediation and water disinfection.

Degradation of Methyl Orange from Aqueous Solution Using Fe-Ni-Co-Based Trimetallic Nanocomposites: Optimization by Response Surface Methodology

Effluent-containing dye molecules is a significant environmental hazard. An economical and energy-saving solution is needed to combat this issue for the purpose of environmental sustainability. In this study, Fe-Ni-Co-based trimetallic nanocomposite was synthesized using the coprecipitation method. Scanning Electron Microscopy (SEM), X-ray diffraction (XRD), and Fourier Transform Infra-Red spectroscopy were conducted to explore the physical morphology, phase structure and functional groups of the synthesized catalyst. Among dyes, methyl orange is considered as a major contaminant in textile effluent. The current study focused on the degradation of methyl orange using a trimetallic Fe-Ni-Co-based nanocomposite. A central composite design in response surface methodology was employed to analyze the independent variables including dye concentration, catalyst dose, temperature, hydrogen peroxide, irradiation time, and pH. Dye degradation has been achieved up to 81% in 20 min at the lowest initial concentration (5 mg/L) in optimized conditions. Based on ANOVA, the predicted values were in great agreement with the actual values, signifying the applicability of response surface methodology in the photocatalytic decolorization of dyeing effluents. The results gained from this research demonstrated that the synthesis method of trimetallic nanocomposite (Iron Triad) is a cost-effective and energy efficient method that can be scaled up to a higher level for industrial application.

Enhanced Photocatalytic Degradation of Organic Dyes by Cerium‐Doped Zinc Oxide Nanocones

AbstractCerium‐doped zinc oxide (Ce‐ZnO) nanocones with cerium concentrations of 0, 0.5, 1, and 2 % were synthesized using a sol‐gel method. Their effectiveness as photocatalysts for degrading dyes such as Rhodamine B (RhB), Methylene Orange (MO), and Methylene Violet (MV) was evaluated. The optical and structural properties, particle size distribution, and morphology of these nanocones were examined using X‐ray diffraction (XRD), scanning electron microscopy (SEM), and ultraviolet‐visible (UV‐Vis) spectrophotometry. XRD results confirmed that the nanocones were highly crystalline with a hexagonal wurtzite structure, and a noticeable blue shift was observed in the Ce‐doped ZnO nanocones compared to pure ZnO. The photocatalytic performance under UV exposure showed that cerium doping significantly improved the degradation of RhB, MO, and MV. Notably, ZnO nanocones doped with 1 % cerium exhibited the highest photocatalytic efficiency, achieving 100 % degradation of RhB within 60 minutes. Additionally, 1 % Ce‐ZnO nanocones demonstrated degradation efficiencies of 86.3 % for MO and 74.9 % for MV within the same time frame.

Ta2O5 coatings modified with CdS, ZnO, and Dy2O3 particles prepared by plasma electrolytic oxidation of tantalum for the photocatalytic degradation of methyl orange

Ta2O5/CdS, Ta2O5/ZnO and Ta2O5/Dy2O3 coatings for application in photocatalytic degradation of methyl orange were prepared by plasma electrolytic oxidation of tantalum in an alkaline electrolyte with different concentrations of CdS, ZnO, and Dy2O3 particles up to 2.0 g/L. The coatings were characterized by SEM/EDS, XRD, Raman spectroscopy, DRS and photoluminescence spectroscopy. The morphology, thickness, phase structure and absorption properties of all coatings are almost identical and independent of the content of CdS, ZnO, and Dy2O3 embedded in Ta2O5 coatings. The orthorhombic and monoclinic phases of Ta2O5 are the main constituents of the coatings. Due to the low content of embedded CdS, ZnO, and Dy2O3 in Ta2O5 coatings, they exhibit high absorption in the middle ultraviolet region, which is characteristic of Ta2O5. The photocatalytic activity (PA) of Ta2O5/CdS, Ta2O5/ZnO and Ta2O5/Dy2O3 is higher than that of pure Ta2O5 and depends on the amount of CdS, ZnO, and Dy2O3 in the electrolyte, respectively. The highest PA was observed for coatings formed in an electrolyte containing 0.5 g/L of CdS, ZnO, and Dy2O3. The improved PA of Ta2O5/CdS, Ta2O5/ZnO and Ta2O5/Dy2O3 compared to Ta2O5 is related to the reduction of photogenerated electron/hole recombination. The mechanism of the photogenerated electron/hole transfer process is presented and discussed.

Plant‐assisted synthesis of Fe3O4 nanoparticles for catalytic degradation of methyl orange dye and electrochemical sensing of nitrite

AbstractThe present study details a more environmentally friendly method for synthesizing iron oxide nanoparticles (Fe3O4‐NPs) utilizing Hibiscus sabdariffa (H. sabdariffa) leaf extract. The produced H. sabdariffa/Fe3O4‐NPs underwent characterization through VSM, XRD, FESEM‐EDX, TEM and FTIR analyses. The FESEM and TEM images revealed that the H. sabdariffa/Fe3O4‐NPs had a narrow distribution and an average particle size of 5±2 nm. Catalytic degradation studies of the synthesized Fe3O4‐NPs exhibited efficient reduction of methyl orange (MO) dye. The degradation of MO catalysed by H. sabdariffa/Fe3O4‐NPs follow the pseudo‐first order kinetics, with a rate constant of 0.0328 s−1 (R2=0.9866). Moreover, in electrochemical sensing studies, the anodic peak current of nitrite (NO2−) for H. sabdariffa/Fe3O4‐NPs/GCE showed a linear relationship with its concentration within the range of 0.5–7.5 mM, achieving a detection limit of 0.29 μM. These findings demonstrate that the modified electrode with Fe3O4‐NPs synthesized using H. sabdariffa leaf extract serve as a novel electrochemical sensor for determining NO2− with high sensitivity and reproducibility.

Novel approach for green synthesis of stable gold nanoparticles with dried turmeric root extract: investigations on sensor and catalytic applications.

In this study, we present the synthesis of gold nanoparticles (AuNPs) using a completely green synthesis method without the use of any additional functionalizing agent, except dried turmeric root extract. The significant synthesis parameters were optimized, and the applicability of AuNPs was investigated in areas such as plasmonic and fluorescent sensing of aluminum (Al3⁺) and chromium (Cr3⁺) ions, reduction of 4-nitrophenol (4-NP), and degradation of methylene blue (MB) and methyl orange (MO) dyes. Characterization studies were performed using UV-Vis spectroscopy, TEM, FTIR, and XRD, revealing that the AuNPs predominantly had a spherical morphology and a very small particle size of 8.5 nm, with stability maintained up to 120 days. The developed AuNP-based plasmonic sensors relied on aggregation-induced decreases in absorption, along with a red shift in the spectra. Fluorescence sensing demonstrated a linear increase in intensity with increasing concentrations of Al3⁺ and Cr3⁺, with detection limits of 0.83 and 1.19 nM, respectively. The catalytic activities of AuNPs were tested in reducing 4-NP and degradations of MB and MO dyes (binary system) in tap water and wastewater, with the reactions following pseudo-first-order kinetics. This study highlights the potential of AuNPs synthesized from turmeric roots for various environmental and sensing applications.

Fabrication of CuO/MoS2@gCN nanocomposite for effective degradation of methyl orange and phenol photocatalytically

Water from the industries contains various organic effluents which are needed to be removed. Photocatalysis is an efficient method to degrade organic effluents that contaminate water and harmfully affect the environment. This study presents the structural, optical characteristics, and photocatalytic activity of the CuO/MoS2 and their composite with gCN. The hydrothermal approach was employed to fabricate MoS2 nanoflowers, and the co-precipitation method to fabricate CuO. The composite with gCN was prepared successfully using an ultrasonication approach. The physio-chemical properties of fabricated photocatalysts were investigated by various characterization techniques. SEM analysis revealed the nanoflower morphology of the prepared MoS2 sample. The photocatalytic activity was examined by the photodegradation of methyl orange dye and phenol. CuO/MoS2@gCN photocatalyst showed 85.14 % degradation of methyl orange and 63.50 % degradation of phenol. Also, the rate constant of CuO/MoS2@gCN was found to be 0.051 min−1 for MO dye and 0.02 min−1 for phenol, which is higher than other synthesized samples. The scavenging experiment was carried out to identify the most photoactive species involved in the organic pollutants photocatalytic degradation. Electrons served as the primary photoactive species in photocatalysis. Consequently, it is concluded from the results that CuO/MoS2@gCN could be employed as an efficient photocatalyst for wastewater treatment.

Theoretical-experimental study of Fe–ZrO2 and Co–ZrO2. Oxidative degradation of methyl orange azo dye

In recent years, advanced oxidation processes (AOPs) based on the generation of sulfate radicals (SO4●-) (SR-AOPs) have emerged as an innovative method for the decontamination of water and wastewater. In this study, Fe(II) and Co(II) catalysts supported on ZrO₂ were synthesized and employed as an activator for PMS and PS for the degradation of methyl orange. The general objective is to gain detailed insight into the interaction between oxidants and supported metal catalysts at the molecular level. Experimental results and density functional theory (DFT) calculations were employed to analyze the potential activation mechanism of the oxidants. The support was prepared via coprecipitation, and metal ion deposition was achieved through incipient wetness impregnation. The characterization of the catalysts was conducted through atomic absorption spectrometry, X-ray diffraction and Fourier-transform infrared spectroscopy. The findings indicated that PMS was the most efficient oxidant, with Co–ZrO2 emerging as the most effective catalyst (77% MO mineralization), compared to Fe–ZrO2, which exhibited a lower degree of mineralization (37.6%) under the specified experimental conditions. The use of PS as an oxidant resulted in low levels of degradation for both catalysts. The remarkable catalytic efficacy of the Co–ZrO₂/PMS system was elucidated through the application of density functional theory (DFT) calculations. These revealed that the adsorption energy of the oxidants on Co–ZrO₂ is lower than that on Fe–ZrO₂, which could facilitate the subsequent release of radicals to the reaction medium.

Electrochemical remediation of methyl orange over reusable biochar ferrite coated photocatalytic plates

Biochar (BC) obtained from biomass pyrolysis holds immense potential for environmental remediation. The efficiency of BC can further be enhanced by incorporating metal nanoparticles (NPs) in the porous carbon matrix. In the present work nanocomposites (NCs) were prepared by the addition of ferrite nanoparticles (FNPs) into an oxidized BC matrix to create BC /Fe3O4 (BCF). This process improves BC stability, electron transfer, conductivity, and photocatalytic ability for dye degradation. Microstructure and functional group analysis of BCF was performed by SEM, XRD, and FTIR showing intercalation of FNPs with surface functionalities of oxidized BC matrix. The B-H curve of FNPs and BCF reveals super paramagnetic behavior with saturation magnetization (Ms, emu/g) of 67.36 and 20.01 respectively. BET surface area analysis shows surface area (m2/gm) 45.81 and 44.19 for oxidized BC and BCF respectively, that attributed to partial blocking of porous carbon matrix by FNPs. UV-DRS supports the semiconducting behavior of BCF with a significantly reduced band gap (eV) of 2.95 over pristine BC (4.76). BCF-coated photocatalytic plates (PCPs) were developed and utilized for the remediation of methyl orange (MeO) in water samples. Degradation of MeO was investigated over time by electrochemical methods. The square wave voltammetric method showed the limit of detection and quantification of 0.09 ppm and 0.28 ppm respectively for MeO over a glassy carbon electrode in 0.1 M acetate buffer. BCF-derived PCPs rendered ∼99 % degradation efficiency against MeO (50 mgL−1) under UV radiation over 240 min. Developed PCPs demonstrate reusability up to 5 cycles without any further purification step and offer efficient degradation of MeO making them suitable for the treatment of water polluted with dyes.

Enhanced photocatalytic degradation of harmful pollutants by MoO3/SiO2/MXene nanocomposite powder catalyst

The search for materials to treat wastewater is especially crucial. Herein, we have prepared 1D molybdenum oxide (MoO3) nanobelts through a hydrothermal approach. The binary (MoO3/SiO2) and ternary composites of MoO3/SiO2/MXene were synthesized via ultrasonication route. The as-prepared MoO3, MoO3/SiO2, and MoO3/SiO2/MXene composites were employed to investigate the photocatalytic behavior of two organic dyes, methyl orange (MO) and crystal violet (CV). The % degradation of MO in the presence of MoO3 nanobelts and MoO3/SiO2 was calculated to be 48.9 % and 74.4 %, respectively. In the case of CV dye, the degradation (%) was observed at 53.7 % and 75.9 %. The MoO3/SiO2/MXene composite revealed the best photocatalytic behavior against both MO and CV dyes by removing 94.7 % and 97.7 % under visible light irradiation. The rate constant values of MoO3 nanobelts, MoO3/SiO2 and MoO3/SiO2/MXene composite for MO dye were calculated to be 0.00568 min−1, 0.01156 min−1, and 0.02399 min−1 and for CV dye 0.00679 min−1, 0.01208 min−1, and 0.02798 min−1 respectively. A scavenging test was carried out to monitor the main photo-active species that take part during the photocatalysis and hydroxyl radicals were found to be the highly active species during whole photodegradation progression. The SiO2 particles function as a good adsorbent medium and transfer the adsorbed organics toward more active sites to advance the reaction. 2D MXene nanosheets, as good conductors, reduce the recombination rate of charges, offer large surface area, and facilitate fast transfer of charges. The results suggest that MoO3/SiO2/MXene composite is a potential contender for wastewater remediation applications.

Fabrication of electrospun PA66 nanofibers loaded with biosynthesized silver nanoparticles: investigation of dye degradation and antibacterial activity.

In the current study, silver nanoparticles (AgNPs) incorporated Polyamide 66 (PA66) nanofiber mat as a photocatalyst which was prepared using electrospinning technique for degradation of methyl orange (MO). Considering the lack of reported studies on the influence of the ultrasonication on the size and stability of AgNPs, the purpose of the study was to produce a small size of AgNPs and compare it with the continuous stirring method. It is reasonable to report that the advantage of ultrasonication is to generate relatively smaller AgNPs (u-AgNPs) compared to fabrication by continuous stirring method (s-AgNPs). Helichrysum arenarium (HA) extract was used as a reducing agent as well as a capping agent in green synthesis of AgNPs. AgNPs were characterized by UV-visible spectrophotometry, Fourier-transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), and transmission electron microscope (TEM). PA66/u-AgNs nanofibers were then successfully electrospun and characterized by using scanning electron microscope (SEM), FT-IR, thermal gravimetric analysis (TGA), and water contact angle measurement (WCA). Fabricated PA66-based nanofiber mat with smooth surface and uniform diameters (330-340nm) was used as a catalyst in MO degradation. PA66/u-AgNP nanofibers were also evaluated for antibacterial performance and showed significant inhibition against Escherichia coli, Staphylococcus aureus, and Pseudomonas aeruginosa bacteria. According to these findings, it is expected that the fabricated novel PA66/u-AgNP nanofibers can be announced as a promising potent and applied to the wastewater applications.