Decontamination Efficacy Research Articles

Decontamination efficacy of sodium hypochlorite solutions for poliovirus

Effective decontamination procedures are critical to the successful manufacture and control of poliovirus vaccines to minimize the risk to personnel and the environment. Polio viruses have been reported to be more resistant to disinfectants than many other viruses. We assessed the efficacy of sodium hypochlorite-containing disinfectants for decontamination for three poliovirus serotypes to implement decontamination procedures that are fully compliant with the WHO GAP III and Health authorities’ requirements. A 10.4 log reduction was observed with a 0.63% sodium hypochlorite solution in a suspension with high protein and high poliovirus concentrations diluted 10-fold compared with a 6 log reduction in an undiluted sample. Treatment efficacy increased with sodium hypochlorite content and decreased with sample protein content. The surface tests showed that two 1-min treatments, 5-min apart, with a 0.63% Chl sodium hypochlorite solution effectively reduced the concentration of all poliovirus serotypes by 10 log10, irrespective of the protein and virus concentration in the sample. Sodium hypochlorite solutions lower than 0.52% were less effective for complete inactivation of poliovirus. In conclusion, we demonstrated that a high level of virus reduction (>10 log10) can be achieved with sodium hypochlorite solutions with poliovirus in suspension and dried on surfaces.

Myco-decontamination of azo dyes: nano-augmentation technologies.

Effluents of textile, paper, and related industries contain significant amounts of synthetic dyes which has serious environmental and health implications. Remediation of dyes through physical and chemical techniques has specific limitations. Augmented biological decontamination strategies 'microbial remediation' may involve ring-opening of dye molecules besides the reduction of constituent metal ions. Both bacterial and fungal genera are known to exhibit metabolic versatility which can be harnessed for effective bio-removal of the toxic dye contaminants. Ascomycetous/basidiomycetes fungi can effectively decontaminate azo dyes through laccase/peroxidase enzyme-mediated catalysis. The extent, efficacy, and range of fungal dye decontamination can be enhanced by the conjugated application of nanomaterials, including nanoparticles (NPs) and their composites. Fungal cell-enabled NP synthesis- 'myco-farmed NPs', is a low-cost strategy for scaled-up fabrication of a variety of metal, metal oxide, non-metal oxide NPs through oxidation/reduction of dissolved ions/molecules by extracellular biomolecules. Augmented and rapid decontamination of azo dyes at high concentrations can be achieved by the use of myco-farmed NPs, NPs adsorbed fungal biomass, and nano-immobilized fungi-derived bio-catalytical agents. This manuscript will explore the opportunities and benefits of mycoremediation and application of fungus-NP bionanoconjugate to remediate dye pollutants in wastewaters and land contaminated with the effluent of textile industries.

Inactivation of virus and bacteria using cold atmospheric pressure air plasmas and the role of reactive nitrogen species

Cold atmospheric pressure plasma has potential as a non-thermal processing technology to decontaminate food and food contact surfaces due to its ability to generate an abundance of reactive oxygen and nitrogen species with antimicrobial attributes at ambient conditions. In this study, we present a comparison on the effectiveness of surface decontamination against feline calicivirus (FCV) and Salmonella spp using four different plasma sources, a dielectric barrier discharge (DBD) in direct contact with the substrate and three remote plasma treatment sources: a 2D DBD, a volumetric DBD and a gliding arc discharge. The plasma sources were all operated in air at atmospheric pressure. The decontamination efficacy was enhanced by the presence of humidity on the sample surface and only direct contact between plasma and samples allowed the inactivation of pathogens on dry substrates. Across all sources, FCV was seen to be more susceptible to the plasma-generated species than Salmonella spp. The diminished effectiveness of the gliding arc discharge compared to the DBDs operating at the same power is most likely due to the low Henry’s law constant of NO, the dominant reactive species generated by the gliding arc. Control experiments illustrate that the co-existence of O3 and NO2, as in the afterglow of the remote DBDs enhances the inactivation compared to the inactivation by O3 or NO2 only. A chemical kinetics model of the plasma effluent and the plasma treatments show a strong correlation between the gas-phase concentration of N2O5 and inactivation of the virus. We experimentally show that the production of N2O5 coincides with the enhanced generation of reactive nitrogen species in the liquid phase.

A hybrid model integrating warm heat and ultraviolet germicidal irradiation might efficiently disinfect respirators and personal protective equipment

BackgroundThe pandemic coronavirus disease 2019 (COVID-19) has taken a heavy toll on human life and has upended the medical system in many countries. The disease has created a system wide worsening shortage of N95, medical masks, and other personal protective equipment (PPE) that is regularly used by healthcare personnel and emergency service providers for their protection.AimConsidering the number of infected patients and the stressed supplies of PPE, reuse of PPE can serve as an efficient contingency plan. Multiple studies have investigated the effect of different decontamination methods.MethodsWe chose the most user-friendly, easily scalable viral decontamination methods, including ultraviolet irradiation and heat treatment. In this paper, we investigated a unique approach to reuse the mask by creating a hybrid model that efficiently sanitizes the infected mask.ResultsThe advantages of the proposed hybrid model as compared to the respective single arms is its decontamination efficacy, operational speed, as well as the number of reuse cycles as verified by mathematical analysis and simulation. This model is mainly intended for medical PPE but can also be used for other domestic and personal sanitization during the COVID-19 pandemic. As per the situation, the hybrid system can be used as standalone systems also. This sanitization process is not only limited to the elimination of Severe acute respiratory syndrome coronavirus 2 but can be extended to any other infectious agents. Thus, our results indicate that the proposed hybrid system is more effective, meets disinfection criterion and time saving for the reuse of respirators and PPE.

Efficacy and safety of decontamination for N95 respirator reuse: a systematic literature search and narrative synthesis.

PurposeUnder times of supply chain stress, the availability of some medical equipment and supplies may become limited. The current pandemic involving severe acute respiratory syndrome coronavirus 2 has highlighted limitations to the ordinary provision of personal protective equipment (PPE). For perioperative healthcare workers, N95 masks provide a stark example of PPE in short supply necessitating the creation of scientifically valid protocols for their decontamination and reuse.MethodsWe performed a systematic literature search of MEDLINE, Embase, Cochrane CENTRAL databases, and ClinicalTrials.gov to identify peer-reviewed articles related to N95 mask decontamination and subsequent testing for the integrity of mask filtration and facial seal. To expand this search, we additionally surveyed the official statements from key health agencies, organizations, and societies for relevant citations.ResultsOur initial database search resulted in five articles that met inclusion criteria, with 26 articles added from the expanded search. Our search did not reveal any relevant randomized clinical trials or cohort studies. We found that moist mask heating (65–80°C at 50–85% relative humidity for 20–30 min) and vaporous hydrogen peroxide treatment were supported by the literature to provide consistent viral decontamination without compromising mask seal and filtration efficiency. Other investigated decontamination methods lacked comprehensive scientific evidence for all three of these key criteria.ConclusionsN95 mask reprocessing using either moist heat or vaporous hydrogen peroxide is recommended to ensure healthcare worker safety.Electronic supplementary materialThe online version of this article (10.1007/s12630-020-01770-w) contains supplementary material, which is available to authorized users.

The combined application of a high voltage, low electrode spacing, and biosurfactants enhances the bio-electrokinetic remediation of petroleum contaminated soil

This study examined the effect of voltage variation, the distance between electrodes and the application of a biosurfactant on the bio-electrokinetic remediation of soil contaminated with petrochemicals. The study was meant to correlate the relationship between voltage, electrode distance, and application of biosurfactants on the efficacy of decontamination. The remediation process involved the application of voltages of 30 V and 10 V with changing electrode spacing of 335 mm and 185 mm. All the electrokinetic setups were spiked with 28 g/L of a biosurfactant. The experiments containing the biosurfactant and run at the highest voltage of 30 V with an electrode spacing of 185 mm had the highest oil recovery efficiency as compared to the other configurations. Decontamination was improved under a high voltage due to the enhancement of electroosmosis and electrophoresis. 30 V increased the energy budget as compared to 10 V in 240 h, but 30 V was more efficient in terms of attaining satisfactory decontamination in the same remediation time. The application of a biosurfactant and lower electrode spacings enhanced desorption and demulsification which led to a reduction in the energy expenditure by accelerating the decontamination process. The variation in voltage did not have detrimental effects on the bacteria but pH affected microbial growth especially in areas closest to the cathode and the anode compartments. The 185 mm electrode spacing presented better bacterial growth conditions as compared to 335 mm electrode spacing. The results were able to show that a high voltage, low electrode spacing and application of a biosurfactant as a combined configuration were able to increase the efficiency and reduce the energy expenditure if satisfactory decontamination was to be achieved. The results also show that electrokinetic remediation can be combined with biosurfactant enhanced bioremediation to remediate soil-water systems. Further studies should be done to study the viability of field scale applications to relate field scale environmental conditions to these lab scale propositions.

In vitro decontamination efficacy of the RSDL® (Reactive Skin Decontamination Lotion Kit) lotion component against riot control agents: Capsaicin, Mace™ (CN) and CS

The study examined the degradation of riot control agents (RCAs): 2-chloroacetophenone (CN), 2-chlorobenzalmalononitrile (CS), and capsaicin, using the Reactive Skin Decontamination Lotion Kit (RSDL®) lotion and evaluated the the direct liquid phase reactivity of the RSDL lotion component with each RCA.RSDL lotion was mixed with the selected RCAs at different molar ratios. Reactivity of the active ingredient potassium 2,3-butanedione monoximate (KBDO) with the RCA was observed for one hour. Samples of 10 μL were taken and quenched, analyzed for residual RCA using LC–MS. CN, was degraded at molar ratios of two and above in less than 2 min. At a molar ratio of 1:1 KBDO:CN, ∼90 % of CN was degraded within 2 min, the remaining 10 % residual CN was observed for one hour without any change. CS, degradation of more than 68 % of CS was achieved at 20:1 M ratio of KBDO:CS within 1 h of reaction time. For capsaicin, no degradation was observed regardless of the higher molar ratios of up to 20:1 and longer reaction times of up to one hour. This study provides evaluation of neutralizing action of the RSDL lotion without assessment of the physical removal component by the RSDL Kit.

A combination process including ionizing radiation for hygienization and shelf life extension of leafy vegetables

Raw leafy greens are commonly associated with global foodborne outbreaks due to pathogenic contaminants. In the current study, greens, such as spinach (Spinacia oleracea L.), coriander (Coriandrum sativum L.) and mint (Mentha spicata L.) showed presence of coliforms (including E. coli)along with other aerobic microbes, yeast and molds. These vegetables mostly consumed in raw or culinary purpose, and hence increase the chances of food borne illnesses. Moreover, the leafy greens are perishable. In this context, we optimized a combination process including radiation treatment to achieve hygienization and shelf life extension of these leafy green vegetables. The combination treatment comprising potable water wash, chlorination (NaOCl-200 ppm) followed by irradiation (2 kGy using electron beam or gamma) was developed, and the processed samples showed keeping quality up to 15 days at 4-6°C, whereas control samples spoiled within two days. The treatment resulted in coliform count below detection level while retaining the nutritional, phenolic content and organoleptic qualities. Thus, the combination treatment could ensure safety, keeping quality enhancement of perishable leafy greens and to control global food outbreaks. Electron beam over gamma processing found to be a commercial viable option due to its high throughput and equal efficacy in microbial decontamination

Analysis of Chemical Simulants in Urine: A Useful Tool for Assessing Emergency Decontamination Efficacy in Human Volunteer Studies.

To date, all human studies of mass-casualty decontamination for chemical incidents have relied on the collection and analysis of external samples, including skin and hair, to determine decontamination efficacy. The removal of a simulant contaminant from the surface of the body with the assumption that this translates to reduced systemic exposure and reduced risk of secondary contamination has been the main outcome measure of these studies. Some studies have investigated systemic exposure through urinary levels of simulant metabolites. The data obtained in these studies were confounded by high background concentrations from dietary sources. The unmetabolized simulants have never been analyzed in urine for the purposes of decontamination efficacy assessment. Urinary simulant analysis could obviate the need to collect skin or hair samples during decontamination trials and provide a better estimate of both decontamination efficacy and systemic exposure. The study objective therefore was to determine whether gross skin contamination as part of a decontamination study would yield urine levels of simulants sufficient to evaluate systemic availability free from dietary confounders. In this study, a gas chromatography-tandem mass spectrometry method was developed for the analysis of two chemical simulants, methyl salicylate (MeS) and benzyl salicylate (BeS), in urine. An extraction and sample clean-up method was validated, enabling quantitation of these simulants in urine. The method was then applied to urine collected over a 24-hour period following simulant application to the skin of volunteers. Both MeS and BeS were present in all urine samples and were significantly increased in all post-application samples. The MeS levels peaked one hour after skin application. The remaining urinary levels were variable, possibly due to additional MeS exposures such as inhalation. In contrast, the urinary excretion pattern for BeS was more typical for urinary excretion curves, increasing clearly above baseline from four hours post-dose and peaking between 12.5 and 21 hours, a pattern consistent with dermal absorption and rapid excretion. The authors propose BeS is a useful simulant for use in decontamination studies and that its measurement in urine can be used to model systemic exposures following skin application and therefore likely health consequences.

Rapid simulation of viral decontamination efficacy with UV irradiation

This paper focuses on viral decontamination by ultraviolet (UV) irradiation technologies. This work develops an efficient and rapid computational method to simulate a UV pulse in order to ascertain the decontamination efficacy of UV irradiation for a surface. It is based on decomposition of a pulse into a group of rays, which are then tracked as they progress towards the target contact surface. The algorithm computes the absorption at the point of contact and color codes it relative to the incoming irradiation. This allows one to quickly quantify the decontamination efficacy across the topology of a structure.

Decontamination of Bacillus Spores with Formaldehyde Vapor Under Varied Environmental Conditions

This study investigated formaldehyde decontamination efficacy against dried Bacillus spores on porous and non-porous test surfaces, under various environmental conditions. This knowledge will help responders determine effective formaldehyde exposure parameters to decontaminate affected spaces following a biological agent release. Prescribed masses of paraformaldehyde or formalin were sublimated or evaporated, respectively, to generate formaldehyde vapor within a bench-scale test chamber. Adsorbent cartridges were used to measure formaldehyde vapor concentrations in the chamber at pre-determined times. A validated method was used to extract the cartridges and analyze for formaldehyde via liquid chromatography. Spores of Bacillus globigii, Bacillus thuringiensis, and Bacillus anthracis were inoculated and dried onto porous bare pine wood and non-porous painted concrete material coupons. A series of tests was conducted where temperature, relative humidity, and formaldehyde concentration were varied, to determine treatment efficacy outside of conditions where this decontaminant is well-characterized (laboratory temperature and humidity and 12 mg/L theoretical formaldehyde vapor concentration) to predict decontamination efficacy in applications that may arise following a biological incident. Low temperature trials (approximately 10°C) resulted in decreased formaldehyde air concentrations throughout the 48-hour time-course when compared with formaldehyde concentrations collected in the ambient temperature trials (approximately 22°C). Generally, decontamination efficacy on wood was lower for all three spore types compared with painted concrete. Also, higher recoveries resulted from painted concrete compared to wood, consistent with historical data on these materials. The highest decontamination efficacies were observed on the spores subjected to the longest exposures (48 hours) on both materials, with efficacies that gradually decreased with shorter exposures. Adsorption or absorption of the formaldehyde vapor may have been a factor, especially during the low temperature trials, resulting in less available formaldehyde in the air when measured. Environmental conditions affect formaldehyde concentrations in the air and thereby affect decontamination efficacy. Efficacy is also impacted by the material with which the contaminants are in contact.

Skin penetration and decontamination efficacy following human skin exposure to fentanyl

Unintentional exposure to potent synthetic opioids during law enforcement seizures and rescue operations can potentially result in incapacitating effects or life-threatening respiratory depression. The hazard comes mainly from inhalation exposure, however, the skin contact risk should be considered. In the present study, the skin penetration of fentanyl and the efficacy of different decontamination protocols were evaluated by applying two forms of fentanyl on dermatomed human skin mounted in a diffusion cell. Studies were performed on dry skin or skin moistened by water, sweat or hand sanitizer.The free base of fentanyl displayed greater skin penetration ability than the hydrochloride salt and a higher steady state penetration rate of fentanyl in solution compared to powder on dry skin. Sweaty skin increased the penetration rate, both when applied in solution and as powder. The hand sanitizer increased skin penetration of the free base fentanyl but not the hydrochloride salt. Of the evaluated decontamination procedures, only soapy water demonstrated a general efficacy.In conclusion, the skin contact hazard of fentanyl is highly dependent on the exposure conditions and contamination density. The risk for physiological effects of fentanyl is assessed to occur only at very high exposures on sweaty skin. In such events, skin decontamination using soap and water is estimated to be a sufficient decontamination procedure.

An insight into curcumin-based photosensitization as a promising and green food preservation technology.

Consumer awareness on the side effects of chemical preservatives has increased the demand for natural preservation technologies. An efficient and sustainable alternative to current conventional preservation techniques should guarantee food safety and retain its quality with minimal side effects. Photosensitization, utilizing light and a natural photosensitizer, has been postulated as a viable and green alternative to the current conventional preservation techniques. The potential of curcumin as a natural photosensitizer is reviewed in this paper as a practical guide to develop a safe and effective decontamination tool for industrial use. The fundamentals of the photosensitization mechanism are discussed, with the main emphasis on the natural photosensitizer, curcumin, and its application to inactivate microorganisms as well as to enhance the shelf life of foods. Photosensitization has shown promising results in inactivating a wide spectrum of microorganisms with no reported microbial resistance due to its particular lethal mode of targeting nucleic acids. Curcumin as a natural photosensitizer has recently been investigated and demonstrated efficacy in decontamination and delaying spoilage. Moreover, studies have shown the beneficial impact of an appropriate encapsulation technique to enhance the cellular uptake of photosensitizers, and therefore, the phototoxicity. Further studies relating to improved delivery of natural photosensitizers with inherent poor solubility should be conducted. Also, detailed studies on various food products are warranted to better understand the impact of encapsulation on curcumin photophysical properties, photo-driven release mechanism, and nutritional and organoleptic properties of treated foods.

The use of ozone gas for the inactivation of Bacillus anthracis and Bacillus subtilis spores on building materials.

A study was conducted to assess the efficacy of ozone gas in inactivating spores of both Bacillus anthracis and Bacillus subtilis inoculated onto six building materials (glass, wood, carpet, laminate, galvanized metal, and wallboard paper). Testing conditions consisted of ozone gas concentrations ranging from 7,000–12,000 parts per million (ppm), contact times from 4 to 12 h, and two relative humidity (RH) levels of 75 and 85%. Results showed that increasing the ozone concentration, contact time, and RH generally increased decontamination efficacy. The materials in which the highest decontamination efficacy was achieved for B. anthracis spores were wallboard paper, carpet, and wood with ≥ 6 log10 reduction (LR) occurring with 9,800 ppm ozone, 85% RH, for 6 h. The laminate and galvanized metal materials were generally more difficult to decontaminate, requiring 12,000 ppm ozone, 85% RH, and 9–12 h contact time to achieve ≥6 LR of B. anthracis. Lastly, overall, there were no significant differences in decontamination efficacy between the two species.

Efficacy and safety of selective decontamination of the digestive tract (SDD) to prevent recurrent hepatic cyst infections in polycystic liver disease: a retrospective case series.

BackgroundHepatic cyst infection is a complication of polycystic liver disease (PLD) that causes substantial morbidity. Repetitive infection is frequent and is increasingly difficult to treat. As translocated gut bacteria are considered the cause, we hypothesize that selective decontamination of the digestive tract (SDD) reduces recurrence of hepatic cyst infection.MethodsWe performed a retrospective, observational study in two referral centres. All patients with PLD treated with SDD for hepatic cyst infection were included. Efficacy was determined by calculating the infection incidence (hepatic cyst infections per month) before and during SDD therapy. Adverse events were scored according to the Common Terminology Criteria for Adverse Events (CTCAE).ResultsWe identified eight patients who received SDD (88% female, 88% polycystic kidney disease). The median age was 65 years (IQR: 51–74 years). SDD lowered the median incidence from 0.09 episodes per month (IQR: 0.06–0.25 episodes per month) to 0.01 episodes per month (IQR: 0.00–0.05 episodes per month) (P = 0.12). Discontinuation of SDD led to rapid recurrence of cyst infection (71% within 6 weeks). SDD consisted of polymyxins with/without aminoglycosides. The median SDD treatment duration was 20 months (range: 3–89 months). Six patients (75%) developed adverse events [CTCAE Grade 1 (gastrointestinal: n = 3) or Grade 3 (ototoxicity: n = 1; fungal infection: n = 1)], mostly attributable to aminoglycosides; one patient developed polymyxin E resistance.ConclusionsSDD prophylaxis provides a novel strategy for limiting recurrent hepatic cyst infection in PLD patients. However, adverse events are frequent and curtail its use. As most were attributable to aminoglycosides, polymyxin E is considered the preferred therapy.

Non-thermal atmospheric gas plasma for decontamination of sliced cheese and changes in quality.

The atmospheric-pressure non-thermal dielectric barrier discharge (DBD) plasma has recently emerged as an efficient decontamination method for the food safety enhancement. Thus the objective of this study was to evaluate the effectiveness of a simple DBD plasma treatment, with a relatively low-frequency power supply operating at 60 Hz, for microbial inactivation. A parametric study of operating conditions for bacterial inactivation was conducted using nutrient agar inoculated with Escherichia coli (2.28--6.28 log CFU/ml). The microbial log reduction was enhanced with increasing input power (30, 50, 70 W) and plasma exposure time (0, 1, 3, 5, 7 min). The inactivation effect was increased by decreasing inter-electrode gap (2, 1.5, 1 cm) and by reducing the initial microorganism concentration. Accordingly, a DBD plasma treatment at 50 W for 10 min could lead to complete killing of E. coli and partial inactivation of Listeria innocua on cheese (mean log reduction: 4.75 ± 0.02 and 0.72 ± 0.01, respectively). The decontamination efficacy of DBD plasma was affected by the types of microorganisms. The changes in hardness and color of cheese were unnoticeable after 10 min treatment with a power of 50 W. Overall, the results suggested that the DBD plasma can be potentially exploited to improve the food safety.

Improved skin decontamination efficacy for the nerve agent VX

Early initiated decontamination is demonstrated to be crucial to avoid systemic effects of highly toxic and low volatile agents exposed on the skin. Skin decontamination can be performed by simple procedures, such as washing with soap and water, or by using advanced decontamination products containing absorption and agent degradation properties. Reactive Skin Decontamination Lotion (RSDL) has demonstrated high efficacy to remove nerve agents from the skin. However, contrary to the current operational recommendations, experimental studies have shown that prolonged skin contact time of RSDL is important for efficient decontamination of VX. In the present study, several RSDL-protocols were evaluated for the efficacy to remove neat VX from human skin in vitro. The decontamination efficacies of the RSDL-procedures were compared with the efficacy of the simple procedure of washing off the skin with soapy water. The RSDL-protocols containing repeated swabbing with the sponge and a 10 min skin contact time of RSDL-lotion demonstrated the greatest decontamination efficacy of all procedures evaluated. Repeating the protocol 2 h after the initial decontamination step resulted in a transient increased skin penetration of remaining intact agent on skin and was followed by rapidly declined agent penetration rate. Decontamination performed with soapy water significantly increased agent amounts penetrating skin, most likely caused by skin hydration and agent dilution. In conclusion, a slightly extended procedure for RSDL-decontamination showed improved efficacy and is therefore recommended for removal of nerve agents from the skin. In addition, it is of highest importance that skin decontamination of nerve agents should consist of procedures using low water content.

Cleaning and disinfection of crates and trucks used for duck transport: field observations during the H5N8 avian influenza outbreaks in France in 2017

Transport of infected birds is thought to play a key role in the spread of avian influenza (AI) on poultry farms during epizootic outbreaks. Ensuring efficient cleaning and disinfection (C&D) of equipment used for transport is needed to prevent the spread of AI. This study aimed to evaluate the efficacy against the AI virus of C&D protocols applied on trucks and crates used for the transport of ducks during the H5N8 AI outbreaks in France in 2017. In 3 abattoirs, 16 transport vehicles and their crates were sampled by swabbing to detect the influenza type A genome by real-time reverse-transcription polymerase chain reaction. Vehicles were tested before and after decontamination, which was carried out in accordance with the abattoirs' protocols. A total of 86 samples out of 299 collected before C&D were positive for AI (29%); 7 trucks out of 16 transported crates detected positive for AI. After C&D, the AI genome was detected in 56 samples out of 308 (18%). Ten trucks were loaded with a shipment of AI-positive crates. Eight vehicles were detected positive in the cabin, on the truck bed, and/or on the wheels. Despite reinforcement of C&D, the efficacy of decontamination was variable among slaughterhouses. The efficacy seemed to depend on the initial contamination load, C&D protocols, and how the protocol is implemented. Breaks in biosecurity measures led to frequent contamination of trucks after C&D. Observational studies during animal health crises are of interest to analyze practices in emergency conditions and to put forward measures aimed at increased preparedness.

Effectiveness of Ultraviolet-C Light and a High-Level Disinfection Cabinet for Decontamination of N95 Respirators.

Background:Shortages of personal protective equipment (PPE) including N95 respirators are an urgent concern in the setting of the global COVID-19 pandemic. Decontamination of PPE could be useful to maintain adequate supplies, but there is uncertainty regarding the efficacy of decontamination technologies.Methods:A modification of the American Society for Testing and Materials standard quantitative carrier disk test method (ASTM E-2197-11) was used to examine the effectiveness of 3 methods, including ultraviolet-C (UV-C) light, a high-level disinfection cabinet that generates aerosolized peracetic acid and hydrogen peroxide, and dry heat at 70°C for 30 minutes. We assessed the decontamination of 3 commercial N95 respirators inoculated with methicillin-resistant Staphylococcus aureus (MRSA) and bacteriophages MS2 and Phi6; the latter is an enveloped RNA virus used as a surrogate for coronaviruses. Three and 6 log10 reductions on respirators were considered effective for decontamination and disinfection, respectively.Results:UV-C administered as a 1-minute cycle in a UV-C box or a 30-minute cycle by a room decontamination device reduced contamination but did not meet criteria for decontamination of the viruses from all sites on the N95s. The high-level disinfection cabinet was effective for decontamination of the N95s and achieved disinfection with an extended 31-minute cycle. Dry heat at 70°C for 30 minutes was not effective for decontamination of the bacteriophages.Conclusions:UV-C could be useful to reduce contamination on N95 respirators. However, the UV-C technologies studied did not meet pre-established criteria for decontamination under the test conditions used. The high-level disinfection cabinet was more effective and met criteria for disinfection with an extended cycle.

Remediating Indoor Pesticide Contamination from Improper Pest Control Treatments: Persistence and Decontamination Studies

The improper and excessive use of pesticides in indoor environments can result in adverse human health effects, sometimes necessitating decontamination of residential or commercial buildings. A lack of information on effective approaches to remediate pesticide residues prompted the decontamination and persistence studies described in this study. Decontamination studies evaluated the effectiveness of liquid-based surface decontaminants against pesticides on indoor surfaces. Building materials were contaminated with 25-2,400 μg/100cm2 of the pesticides malathion, carbaryl, fipronil, deltamethrin, and permethrin. Decontaminants included both off-the-shelf and specialized solutions representing various chemistries. Pesticides included in this study were found to be highly persistent in a dark indoor environment with surface concentrations virtually unchanged after 140 days. Indoor light conditions degraded some of the pesticides, but estimated half-lives exceeded the study period. Decontamination efficacy results indicated that the application of household bleach or a hydrogen peroxide-based decontaminant offered the highest efficacy, reducing malathion, fipronil, and deltamethrin by >94-99% on some surfaces. Bleach effectively degraded permethrin (>94%), but not carbaryl (<70%) while the hydrogen peroxide containing products degraded carbaryl (>71-99%) but not permethrin (<54%). These results will inform responders, the general public and public health officials on potential decontamination solutions to remediate indoor surfaces.