Dc Magnetic Flux Research Articles

Graphene-based terahertz antenna with polarization reconfiguration

This article presents the design of a terahertz antenna with the ability to reconfigure its polarization using graphene’s anisotropic properties. By applying a DC magnetic flux, the graphene conductivity tensor can be transformed into a non-diagonal tensor. Conversely, the magnetic bias can be switched off to revert the tensor to a diagonal state. This approach allows the antenna to switch between linear and circular polarizations, making it highly versatile for terahertz applications. Additionally, by altering the direction of the applied DC magnetic bias, one can select the rotation direction of circular polarization between left and right hand. The feeding line and ground plane of the antenna are made of silver metal, and its behavior in the terahertz band is described using the Modified Relaxation-Effect model, which is more accurate than the skin effect model for this band. The finite element numerical method is utilized to analyze the antenna, which yields results consistent with the design predictions. The antenna’s impedance bandwidth spans 2.8 to 3.22 terahertz for linear polarization and 2.9 to 3.18 THz for circular polarization. The antenna’s maximum gain is 6 dB for linear polarization and 5 dB for circular polarization. The axial ratio for circular polarization is 1.36 in the middle of the band, which is below the 3 dB threshold for circular polarization. The antenna produces directive patterns for both linear and circular polarizations. The key innovation of this antenna design lies in its unique utilization of a magnetostatic field to achieve reconfiguration in the terahertz graphene dielectric resonator antenna, a method that has not been previously documented in literature.

Three-wave mixing traveling-wave parametric amplifier with periodic variation of the circuit parameters

We report on the implementation of a near-quantum-limited, traveling-wave parametric amplifier that uses three-wave mixing (3WM). To favor amplification by 3WM, we use superconducting nonlinear asymmetric inductive element (SNAIL) loops, biased with a dc magnetic flux. In addition, we equip the device with dispersion engineering features to create a stopband at the second harmonic of the pump and suppress the propagation of the higher harmonics that otherwise degrade the amplification. With a chain of 440 SNAILs, the amplifier provides up to 20 dB gain and a 3-dB bandwidth of 1 GHz. The added noise by the amplifier is found to be less than one photon.

Supplementary comparison of national standard instruments in the field of magnetic flux density and magnetic flux measurements by sensing coils

Main textThe COOMET.EM-S26 (1715) supplementary comparison of national standard instruments in the field of magnetic flux density and magnetic flux measurements by sensing coils has been organized within the CCEM framework to test the abilities of the metrology institutes to measure magnetic flux density and magnetic flux.Five NMIs participated in the supplementary comparison COOMET.EM-S26 (1715). Ural Research Institute for Metrology (UNIIM) (since 2020 it has been called Affiliated Branch of D.I. Mendeleev Institute for Metrology (VNIIM-UNIIM)), Russian Federation, acted as the coordinating laboratory of the comparison.The comparison on DC magnetic flux density and magnetic flux was carried out through the measurement of the coil constant of transfer standard coils. In general, very good agreement of the results has been observed.To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database https://www.bipm.org/kcdb/.The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Tuning of strong nonlinearity in radio-frequency superconducting-quantum-interference-device meta-atoms.

Strong nonlinearity of a self-resonant radio-frequency (rf) superconducting-quantum-interference-device (SQUID) meta-atom is explored via intermodulation (IM) measurements. Previous work in zero dc magnetic flux showed a sharp onset of IM response as the frequency sweeps through the resonance. A second onset at higher frequency was also observed, creating a prominent gap in the IM response. By extending those measurements to nonzero dc flux, different dynamics are revealed, including dc flux tunability of the aforementioned gaps and enhanced IM response near geometric resonance of the rf SQUID. These features observed experimentally are understood and analyzed theoretically through a combination of a steady-state analytical modeling and a full numerical treatment of the rf SQUID dynamics. The latter in addition predicts the presence of chaos in narrow parameter regimes. The understanding of intermodulation in rf SQUID metamaterials is important for producing low-noise amplification of microwave signals and tunable filters.

Graphene as a Perfect Conductor

Here, we show that the graphene sheet, which is designed to behave a band insulator, can be turned into a perfect conductor, when the difference of the current from the two valleys gets coupled to an Abelian gauge field. The graphene sheet in such a case is found to display infinite DC conductivity, Debye screening and magnetic flux expulsion.

Modeling and Advanced Control of Dual-Active-Bridge DC–DC Converters: A Review

This article classifies, describes, and critically compares different modeling techniques and control methods for dual-active-bridge (DAB) dc–dc converters and provides explicit guidance about the DAB controller design to practicing engineers and researchers. First, available modeling methods for DAB including reduced-order model, generalized average model, and discrete-time model are classified and quantitatively compared using simulation results. Based on this comparison, recommendations for suitable DAB modeling method are given. Then, we comprehensively review the available control methods including feedback-only control, linearization control, feedforward plus feedback, disturbance-observer-based control, feedforward current control, model predictive current control, sliding mode control, and moving discretized control set model predictive control. Frequency responses of the closed-loop control-to-output and output impedance are selected as the metrics of the ability in voltage tracking and the load disturbance rejection performance. The frequency response plots of the closed-loop control-to-output transfer function and output impedance of each control method are theoretically derived or swept using simulation software PLECS and MATLAB. Based on these plots, remarks on each control method are drawn. Some practical control issues for DAB including dead-time effect, phase drift, and dc magnetic flux bias are also reviewed. This article is accompanied by PLECS simulation files of the reviewed control methods.

Development of an Array of Kinetic Inductance Magnetometers (KIMs)

We describe optimization of a cryogenic magnetometer that uses nonlinear kinetic inductance in superconducting nanowires as the sensitive element instead of a superconducting quantum interference device (SQUID). The circuit design consists of a loop geometry with two nanowires in parallel, serving as the inductive section of a lumped LC resonator similar to a kinetic inductance detector (KID). This device takes advantage of the multiplexing capability of the KID, allowing for a natural frequency multiplexed readout. The Kinetic Inductance Magnetometer (KIM) is biased with a DC magnetic flux through the inductive loop. A perturbing signal will cause a flux change through the loop, and thus a change in the induced current, which alters the kinetic inductance of the nanowires, causing the resonant frequency of the KIM to shift. This technology has applications in astrophysics, material science, and the medical field for readout of Metallic Magnetic Calorimeters (MMCs), axion detection, and magnetoencephalography (MEG).

Steady-State and Transient DC Magnetic Flux Bias Suppression Methods for a Dual Active Bridge Converter

This article presents dc magnetic flux bias suppression methods for a dual active bridge (DAB) converter in both steady state and transient process. The steady-state dc offset is caused by asymmetries of the circuit and power switches in practice, while the transient offset is caused by the sudden update of phase shift ratio. This dc bias will increase the conduction losses, lead to loss of zero voltage switching (ZVS), and even saturate the magnetic components. To prevent this risk, this article proposes methods to suppress the dc bias both in steady state and transient process. For steady-state dc bias suppression, the duty cycles of square voltages generated by the primary and secondary side H-bridges are regulated according to the dc bias current. The conditions to achieve zero dc bias and the small-signal model to regulate the dc bias current are derived. For transient dc bias suppression, the phase shift ratio variation is limited to ensure the peak inductor current within the safe operating range. Tunnel magnetoresistance (TMR) is employed to sense the currents, and an analog integration and sampling method is proposed to detect dc bias. Finally, the proposed method is verified through experimental results on a 3200-W DAB prototype.

Digital fluxgate current sensor based on second harmonic detection

This paper presents a new digital fluxgate current sensor based on second harmonic detection for DC and AC measurement. The sensor utilizes a feedback loop to obtain an almost zero-flux condition, i.e., a balance between the magnetic flux of the primary current and the feedback current, in which way the feedback current is proportional to the primary current. The AC magnetic flux is detected with an induction coil, and the DC zero-flux condition is realized by magnetic saturation effect method, where the magnetic core is periodically magnetized and then the second harmonic of the magnetization current is calculated as an indication of the DC magnetic flux. After theoretical derivation, the operating principle of the sensor was investigated using a numerical simulation model built with Simulink of MATLAB. In addition, a prototype sensor was developed and tested. The experiment results demonstrate that the current sensor works properly for DC and AC measurement. The average error is about 0.06% for DC measurement.

Design and Performance of the 850-V 100-kW 16-kHz Bidirectional Isolated DC–DC Converter Using SiC-MOSFET/SBD H-Bridge Modules

This article designs, builds, and tests the 850-V 100-kW 16-kHz bidirectional isolated dc–dc converter using the latest 1.2-kV 400-A SiC- mosfet /SBD H-bridge modules, with focus on efficiency improvement. Here, SBD stands for Schottky barrier diode. It proposes intermittent operation with continuous-current mode (CCM), to reduce switching losses in partial loads. Experimental results verify that the conversion efficiency from the dc input to the dc output is as high as 99.3% at the rated power of 100 kW, and 99.2% at a partial load of 10 kW. These are measured and calculated, discarding auxiliary power losses of 82 W in total, which are produced by the digital controller, gate-drive circuits, and cooling fans. Experimental transient waveforms show that no dc magnetic flux is included in the 850-V 100-kW 16-kHz transformer at intervals of switchover between the continuous operation and the CCM intermittent operation when power reversal from $-$ 100 to 100 kW is performed at an interval of 1 ms. Finally, this article presents an experimental and theoretical discussion on the voltage ripples appearing across the dc capacitor of each bridge.

Suppression for DC Magnetic Flux for a Current-Fed Bi-Directional Isolated DC-DC Converter under Boost Mode

Suppression for DC Magnetic Flux for a Current-Fed Bi-Directional Isolated DC-DC Converter under Boost Mode

The Comparative Analysis of AC-Flux and DC-Flux Resolvers

Resolver, as an electromagnetic sensor, is widely used in many industrial applications. It can detect the position of the rotary part of the electric machines precisely. In commercial resolvers, the excitation winding is connected to the high frequency (HF) AC source. The amplitude-modulated voltages induced in the signal windings need to be demodulated in order to calculate the envelope of the output signals and accordingly detect the position. On the other hand, in PM-resolver, signal windings replaced by Hall-effect sensors to measure the DC magnetic flux which is produced by permanent magnets. In this study, the performance of both AC and DC flux resolvers is investigated under different circumstances. All the simulations are done by the time-stepping finite element method (TSFEM).

Architecture to achieve nuclear magnetic resonance spectroscopy with a superconducting flux qubit

We theoretically analyze the performance of the nuclear magnetic resonance (NMR) spectroscopy with a superconducting flux qubit (FQ). Such NMR with the FQ is attractive because of the possibility to detect the relatively small number of nuclear spins in a local region ($\sim\mu$m) with low temperatures ($\sim$ mK) and low magnetic fields ($\sim$ mT), in which other types of quantum sensing schemes cannot easily access. A sample containing nuclear spins is directly attached on the FQ, and the FQ is used as a magnetometer to detect magnetic fields from the nuclear spins. Especially, we consider two types of approaches to NMR with the FQ. One of them is to use spatially inhomogeneous excitations of the nuclear spins, which are induced by a spatially asymmetric driving with radio frequency~(RF) pulses. Such an inhomogeneity causes a change in the DC magnetic flux penetrating a loop of the FQ, which can be detected by a standard Ramsey measurement on the FQ. The other approach is to use a dynamical decoupling on the FQ to measure AC magnetic fields induced by Larmor precession of the nuclear spins. In this case, neither a spin excitation nor a spin polarization is required since the signal comes from fluctuating magnetic fields of the nuclear spins. We calculate the minimum detectable density (number) of the nuclear spins for the FQ with experimentally feasible parameters. We show that the minimum detectable density (number) of the nuclear spins with these approaches is around $10^{21}$ /cm$^3$ ($10^8$) with an accumulation time of a second.

Electromagnetic Vibration Analysis of Magnetically Controlled Reactor Considering DC Magnetic Flux

The main factors of stress distribution in MCRs are the magnetostriction effect of the core materials and the magnetic force between gaps under DC bias excitation. This article developed a coupling model for MCRs considering Maxwell magnetic force and magnetostriction under DC flux density biases. The constitutive equations of the magnetic field and strain field are constructed based on the magnetic property curves with a new measured and analyzed method to consider DC magnetic flux biases, which is the key contributions of this study. Then, the electromagnetic vibration properties of the MCR model are calculated and analyzed. To prove the validity of the proposed method, the vibration of a 4.4 kVar-220 V MCR is tested and analyzed.

Accurate 3-axis measurement of inhomogeneous magnetic fields

Abstract Hall effect based Teslameters/Gaussmeters measure DC and AC magnetic flux densities in the range from a few µT to about 30 T. For accurate measurement a 3-axis Hall probe is applied with small magnetic field sensitive volume (MFSV) of 100 µm × 10 µm × 100 µm, with vertical and horizontal Hall elements integrated on a single chip. The planar Hall effect, that produces additional measurement errors is suppressed by the spinning current technique. The orthogonality error of the 3-axis Hall probe is reduced to smaller than 0.1° by the described calibration procedure. This paper explains why the above features are crucial for some applications in industry and modern science for accurate measurement of inhomogeneous magnetic fields and how to achieve them. The future technology trends in magnetic metrology are introduced and the newly developed Nanomapper that incorporates a 3-axis Hall probe with a MFSV of smaller than 10×10×10 micrometer is presented.

Evaluation of a Magnetic Dipole Model in a DC Magnetic Flux Leakage System

One of the most common methods for performing non-destructive testing in steel tank floors is DC magnetic flux leakage (MFL). The magnetic dipole method is the most widely used mathematical technique to predict the MFL from defects in such structures. However, due to the complexity of an exact analytical description of an MFL system, researchers often make coarse approximations for the profile of the magnetic surface charge density $\sigma _{m}$ , orientation of the magnetic field H, and variation of relative permeability $\mu _{r}$ . In this paper, the validity of these approximations is evaluated for 2-D rectangular defects in a steel plate, by comparing model predications with finite element results. The primary sources of deviation between the approximate solutions and true MFL profiles were found to be caused by assumptions that 1) $\sigma _{m}$ on the specimen surface adjacent to a flaw is zero. This assumption is equivalent to treating the orientation of H to be parallel to the specimen surface, even at locations in close proximity to a flaw and 2) local variation in permeability around the defect can be ignored. This approximation was found to cause an underestimation of $\sigma _{m}$ and, consequently, the predicted MFL. In contrast, approximating $\sigma _{m}$ to be zero at the bottom of a flaw, and approximating uniform distribution for $\sigma _{\mathbf {m}}$ on the vertical defect sides of a slot defect was found to generate only minor errors in an estimate of flux leakage.

Tunable Superconducting Cavity using Superconducting Quantum Interference Device Metamaterials

Here we consider a tunable superconducting cavity that can be used either as a tunable coupler to a qubit inside the cavity or as a tunable low noise, low temperature, RF filter. Our design consists of an array of radio-frequency superconducting quantum interference devices (rf SQUIDs) inside a superconducting cavity. This forms a tunable metamaterial structure which couples to the cavity through its magnetic plasma frequency. By tuning the resonant frequency of the metamaterial through an applied magnetic flux, one can tune the cavity mode profile. This allows us to detune the cavity initially centered at 5.593 GHz by over 200 MHz. The maximum quality factor approaches that of the empty cavity, which is 4.5 × 106. The metamaterial electromagnetic response is controlled via a low-frequency or dc magnetic flux bias, and we present a control line architecture that is capable of applying sufficient magnetic flux bias with minimal parasitic coupling. Together this design allows for an in-situ tunable cavity which enables low-temperature quantum control applications.

Imaging collective behavior in an rf-SQUID metamaterial tuned by DC and RF magnetic fields

We examine the collective behavior of two-dimensional nonlinear superconducting metamaterials using a non-contact spatially resolved imaging technique. The metamaterial is made up of sub-wavelength nonlinear microwave oscillators in a strongly coupled 27 × 27 planar array of radio-frequency Superconducting QUantum Interference Devices (rf-SQUIDs). By using low-temperature laser scanning microscopy, we image microwave currents in the driven SQUIDs while in non-radiating dark modes and identify the clustering and uniformity of like-oscillating meta-atoms. We follow the rearrangement of coherent patterns due to meta-atom resonant frequency tuning as a function of external dc and rf magnetic flux bias. We find that the rf current distribution across the SQUID array at zero dc flux and small rf flux reveals a low degree of coherence. By contrast, the spatial coherence improves dramatically upon increasing the rf flux amplitude, in agreement with simulation.

MAGNETOSTATIC FIELD ANALYSIS OF DC COMMUTATOR MOTORS WITH GEAR-TEETH ON THE ROTOR

This paper presents the open-circuit magnetostatic field analysis of a DC commutator motor by applying 1-D and 2-D equivalent magnetic circuit methods. For the 1-D and 2-D equivalent magnetic circuit method, the average air-gap flux density of a DC commutator motor and magnetic flux in every node are derived respectively, and the validity is verified by the finite-element analysis. The Carter’s coefficient is applied to model the permeance of the slot and gear-teeth space. The differences of the air-gap flux density are 3.21% and 3.06% for 1-D and 2-D methods, respectively. The flux linkages, back-EMF constants, cogging torques, electromagnetic torques, and torque ripples of the two gear profiles with feasible number of teeth integrated on the rotor are analyzed to verify the effects of gear profiles. The result shows that the gear-teeth integrated on the motor act as dummy slots, which reduce the cogging torque and torque ripple by 92.02% and 50.14 %, respectively.

Characterization and Modeling of a Virtual Air Gap by Means of a Reluctance Network

This paper deals with an analytical model of the virtual air gap (VAG) function in order to define design rules when this technique is used inside complex devices. The establishment of those design rules constitutes the main originality of the developments presented in this paper, which are about a single-phase magnetic core. It is based on the definition of a nonlinear reluctance network that takes simultaneously into account the effects of dc and ac magnetic flux components in the disturbed area that contains the VAG. The results are validated using a finite-element analysis and experimentally.