Dark-field Scanning Transmission Electron Research Articles

Flame made low Pt loading catalysts supported on different metal oxides for catalytic combustion of CO and CH4

Catalytic combustion is an effective approach to remove air pollutants from various emission sources. For this purpose, supported noble metal catalysts are preferred in commercial applications due to their outstanding catalytic activity for eliminating CO, hydrocarbon compounds and NOx. In this paper, we employ the flame spray pyrolysis method to prepare a series of Pt-based catalysts with four different supports (TiO2, ZrO2, MgO and ZnO) and variable low Pt loadings for catalytic combustion of CO and CH4. The performance of 0.5 Pt/TiO2 is the best in all samples, in which the T90 temperatures are 107 and 500 °C for 90% conversion of CO and CH4, respectively. To examine its thermal stability, a time-on-stream test at 700 °C for 420 min is carried out, resulting in a decrease of about 5% in the final conversion of CH4. The X-ray diffraction results show that TiO2 support is a mixed phase with a major amount of anatase and a small amount of rutile other than a pure phase of ZrO2, MgO and ZnO. Furthermore, X-ray photoelectron spectroscopy analysis and high-angle annular dark-field scanning transmission electron microscopy observation show that when the Pt loading is low, the Pt species exist as highly dispersed single atoms on the surface of the TiO2 support. As the Pt loading gradually increases, the state of the Pt species transitions from single atoms to Pt clusters, resulting in a decrease in dispersion. Ultimately, the Pt can successfully accumulate on the surface of the TiO2 nanoparticles, providing abundant active sites for efficient catalytic combustion reactions.

Modulated crystallographic shear structure in titanium–chromium oxides: their structure and phonon-transport properties

Advancements in phonon engineering have propelled the study of heat conduction within nanostructures, focusing on the wave nature of phonons for thermal conductivity manipulation. This work investigates the annealing-induced structural transformation of titanium–chromium oxide crystals, highlighting a role in modulating thermal conductivity through the regularization of crystallographic shear (CS) plane spacing. Utilizing high-angle annular dark-field scanning transmission electron microscopy and selected-area electron diffraction, a transformation from disordered to ordered arrangements of CS planes was observed through annealing at high temperatures. The thermal conductivity increased following annealing. The variability observed in the spacing of CS planes before annealing implies that phonon Anderson localization might play a role in the changes in thermal conductivity.

Capturing low-concentration benzene: Design and mechanism of high-performance Cu1-Ox,Ny-C single-atom adsorbents

Common adsorbents, such as active carbons, zeolites, and metal–organic frameworks (MOFs), struggle to capture low concentrations of benzene. Single-atom adsorbents (SAAs), boasting exceptional atomic utilization efficiency and precisely tailored electronic structures, offer a promising solution. This study first designed Cu1-Ox,Ny-C SAAs and explored their enhanced benzene adsorption through density functional theory (DFT). Particularly, a crucial link between the SA coordination configuration and its affinity for benzene was established. Next, Cu1-Ox,Ny-C was synthesized from the MOF MIL-101(Cr) and extensively characterized using high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) and X-ray absorption fine structure (XAFS) spectroscopy, etc. to determine the coordination configuration of Cu single atoms. Finally, a thorough evaluation of the Cu1-Ox,Ny-C’ capacity and stability was conducted. Theoretical analysis revealed that Cu single atoms within the Ox,Ny-C matrix act as the primary adsorption sites for benzene. Notably, O and N atoms work synergistically: oxygen atoms promote adsorption, while nitrogen atoms mainly stabilize single-atom sites. Cu1-Ox,Ny-C was successfully synthesized, and characterization revealed that Cu1-O2,N2(trans)-C and Cu1-O3,N1-C were the dominant coordination configurations. Remarkably, despite a fourfold decrease in specific surface area compared to MIL-101(Cr), Cu1-Ox,Ny-C exhibited a threefold increase in chemisorption capacity for low-concentration benzene. Moreover, it exhibits excellent resistance to H2O and can be effectively reused. This study demonstrates a valuable strategy for designing and creating highly efficient SAAs for capturing low concentrations of benzene.

High-performance electrocatalyst for PEMFC cathode: Combination of ultra-small platinum nanoparticles and N-doped carbon support

To accelerate the implementation of zero-emission power installations based on proton-exchange membrane fuel cells, it is necessary to maximize the power characteristics of these devices. For this purpose, we have obtained and tested a new N-doped carbon support and a synthesized Pt/C catalyst based on it with a platinum loading of about 37.3 %. A comparison of the degradation resistance of the initial support and the N-doped one has shown greater stability of the latter. At the same time, Raman spectroscopy has confirmed the presence of the C–N bond, which indicates the successful doping of carbon with nitrogen. The resulting Pt/C catalyst based on an N-doped support is characterized by a substantially narrow size dispersion and an ultra-small nanoparticle size of about 2.6 nm. The high-angle annular dark-field scanning transmission electron microscopy images of the synthesized catalyst have confirmed the presence of individual platinum atoms/clusters uniformly distributed over the surface of the support, and their presence is due to nitrogen embedded into the carbon structure. This material is characterized by a 50 m2 gPt-1 larger electrochemically active surface area and a 227 A gPt-1 greater mass activity compared to the commercial JM40 analog (40 % platinum loading). Meanwhile, the electrochemical parameters remaining after the accelerated stress testing are almost 2 times higher than those of JM40. And the power characteristics in the membrane electrode assembly for the catalyst synthesized by the facile one-pot synthesis method are 13 % (575 mW cm-2) higher than those of the commercial analog (500 mW cm-2). The Pt/C catalyst obtained during the research is deemed promising for commercial use in proton-exchange membrane fuel cells.

Influence of excess silicon on polytype selection during metal-mediated epitaxy of GaN nanowires

We have examined the origins of polytype selection during metal-mediated molecular-beam epitaxy of GaN nanowires (NWs). High-angle annular dark-field scanning transmission electron microscopy reveals [111]-oriented zinc blende (ZB) NWs and [0001]-oriented wurtzite (WZ) NWs, with SixNy at the interface between individual NWs and the Si (001) substrate. Quantitative energy dispersive x-ray spectroscopy reveals a notably higher Si concentration of 7.0% ± 2.3% in zinc blende (ZB) NWs than 2.3% ± 1.2% in wurtzite (WZ) NWs. Meanwhile, density functional theory calculations show that incorporation of 8 at. % Si on the Ga sublattice inverts the difference in formation energies between WZ and ZB GaN, such that the ZB polytype of GaN is stabilized. This identification of Si and other ZB polytype stabilizers will enable the development of polytype heterostructures in a wide variety of WZ-preferring compounds.

Elemental distribution and site occupancy in a Co-Ni-Al-Ti-Ta-W superalloy

γ'-precipitate strengthened cobalt-based superalloys show promise for higher temperature-capability over nickel-based superalloys due to higher melting temperatures. This study investigates a multicomponent CoNi-based superalloy with composition of 54Co-30Ni-9Al-1Ta-4Ti-2-W (at.%) in terms of elemental partitioning and site occupancy. Atom probe tomography (APT) reveals preferential partitioning of Ni, Al, Ti, Ta and W to the γ'-precipitate and Co to the γ-matrix. Aberration-corrected high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) and energy dispersive spectrometer (EDS) along the [001] zone axis of γ'-precipitate with L12 structure indicate that Co, Ni substitute at A-sites, whereas Al, Ti, Ta, W prefer the B-sites. Density functional theory (DFT) calculations further confirm the results of partitioning behaviors and site preferences. Clarifying elemental partitioning and site occupancy provides valuable insights into alloy design principles for advanced CoNi-based superalloys.

Application of Weak-Beam Dark-Field STEM for Dislocation Loop Analysis †.

Nanoscale dislocation loops formed by irradiation can significantly contribute to both irradiation hardening and embrittlement of materials when subjected to extreme nuclear reactor environments. This study explores the application of weak-beam dark-field (WBDF) scanning transmission electron microscopy (STEM) methods for quantitative irradiation-induced defect analysis in crystalline materials, with a specific focus on dislocation loop imaging and analysis. A high-purity Fe-5 wt% Cr model alloy was irradiated with 8 MeV Fe2+ ions at 450°C to a fluence of 8.8 × 1019 m-2, inducing dislocation loops for analysis. While transmission electron microscopy (TEM) has traditionally been the primary tool for dislocation imaging, recent advancements in STEM technology have reignited interest in using STEM for defect imaging. This study introduces and compares three WBDF STEM methods, demonstrating their effectiveness in suppressing background contrasts, isolating defect information for dislocation loop type classification, providing finer dislocation line images for small loop analysis, and presenting inside-outside contrast for identifying loop nature. Experimental findings indicate that WBDF STEM methods surpass traditional TEM approaches, yielding clearer and more detailed images of dislocation loops. The study concludes by discussing the potential applications of WBDF STEM techniques in defect analysis, emphasizing their adaptability across various material systems beyond nuclear materials.

Atomic structure of GPB-II zone and its evolution in an Al-Zn-Mg-Cu-Si crossover alloy during aging

The GPB-II zone is the main strengthening precipitate in the Al-4.5Zn-1.5Mg-1.0Cu-0.35Si (wt.%) crossover alloy, resulting in increased alloy strength and ductility. The atomic structure of the GPB-II zone and its evolution process during aging have been studied by high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) in the present work. It is shown that the GPB-II zone is a hybrid precipitate consisting of the L phase (a disordered phase with a QP lattice and is normally present in Al-Mg-Si-Cu alloy) on the inner part and Guinier-Preston-Bagaryatsky (GPB) zones (an important strengthening phase in Al-Cu-Mg alloy) on the outer part. The GPB-II zone is formed by the GPB zone nucleating at the Cu site (in-between and on the Si-network) of the L phase. The unique combination of the GPB zone and L phase was investigated, and the “Si parallelogram embedding with Cu” was proposed. The GPB zone provides the atoms for the L phase’s growth and results in the coarsening of the L phase with few GPB zones after a long aging time. The role of the Zn element in the formation of the GPB-II zone was discussed. It is thought to have a similar effect as Cu and can also promote the formation of GPB zones on the L phase.

Interface structure of α-Mg/14H-LPSO: First-principles prediction and experimental study

The interfacial structure of the α-Mg/14H-LPSO phase in rare earth-including magnesium alloy was investigated via high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) imaging and first-principles calculations of density-functional theory. Eleven possible interfacial models were constructed according to the different terminations of the LPSO phase, and the corresponding interfacial energies were calculated, from which the four most stable structures (Ter1-MgY-hollow, Ter2-Zn-hollow, Ter3-MgYII-hollow and Ter4-Mg-bridge) were obtained. The interfacial phase diagrams related to the Y chemical potentials were obtained from the calculations, and the most stable interfacial structure was evaluated. Ter1-MgY-hollow and Ter2-Zn-hollow have the lowest interfacial energies in the range of −0.7 eV < ΔμY < −0.6 eV, where fluctuating change of state is the minimized and the interface is the most stable. The separation work of the two models was calculated to predict the bonding strength of the structures at both ends of the interface. The calculation results show that the maximum interfacial separation work is 1.45 J/m2 for the interface model of α-Mg and 14H-LPSO phase structure with Ter2-Zn-hollow termination.

Morphology and crystallography of E-(Al18Cr2Mg3) nano dispersoids in 7475 Al alloy

The morphology and crystallography of E-(Al18Cr2Mg3) nano dispersoids in 7475 Al alloy have been studied by using transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM), high angle annular dark field scanning transmission electron microscopy (HAADF-STEM) and electron tomography (ET). Seven distinct morphologies have been three-dimensionally distinguished at the nanoscale: (i) triangular plates on {111}Al, (ii) hexagonal plates on {111}Al, (iii) rods parallel to 〈110〉Al, (iv) small tetrahedra with {111}Al facets, (v) small octahedra, (vi) spheres and (vii) irregular shapes. Twinning can contribute to the diverse morphologies of E nano dispersoids. The orientation relationships (ORs) between E nano dispersoids and Al matrix have been systematically investigated by selected area electron diffraction (SAED) patterns, HRTEM and matrix calculation. The results from the matrix calculation indicate the absence of clear ORs between E nano dispersoids and Al matrix in 7475 Al alloy.

Low-coordinated Mn–N2 sites in graphene oxide induce peroxydisulfate activation for tetracycline degradation: Process optimization and theoretical calculation

Atom-dispersed low-coordinated transition metal-Nx catalysts exhibit excellent efficiency in activating peroxydisulfate (PDS) for environmental remediation. However, their catalytic performance is limited due to metal-N coordination number and single-atom loading amount. In this study, low-coordinated nitrogen-doped graphene oxide (GO) confined single-atom Mn catalyst (Mn-SA/NGO) was synthesized by molten salt-assisted pyrolysis and coupled to PDS for degradation of tetracycline (TC) in water. Aberration-corrected high-angle annular dark-field scanning transmission electron microscopy (AC-HAADF-STEM) and X-ray absorption fine structure spectroscopy (XAFS) analysis showed the successful doping of single-atom Mn (weight percentage 1.6%) onto GO and the formation of low-coordinated Mn–N2 sites. The optimized parameters obtained by Box-Behnken Design achieved 100% TC removal in both prediction and experimental results. The Mn-SA/NGO + PDS system had strong anti-interference ability for TC removal in the presence of anions. Besides, Mn-SA/NGO possessed good reusability and stability. O2•−, •OH, and 1O2 were the main active species for TC degradation, and the TC mineralization reached 85.1%. Density functional theory (DFT) calculations confirmed that the introduction of single atoms Mn could effectively enhance adsorption and activation of PDS. The findings provide a reference for the synthesis of high-performance single-atom catalysts for effective removal of antibiotics.

Effect of Pre-Deformation on Precipitation in Al–Zn–Mg–Cu Alloy

AbstractIn this work, strengthening effects and evolution of precipitates in a pre-deformed Al–Zn–Mg–Cu alloy during ageing were investigated using Vickers hardness measurements, tensile tests, and high angle annular dark field scanning transmission electron microscopy (HAADF-STEM). It was found that all cold rolled conditions had higher mechanical strength than the non-deformed condition for all ageing times and that this effect increases at higher deformation ratios. It was also found that the non-deformed condition has a higher age hardening response than that of the cold rolled conditions. A homogeneous precipitate distribution was observed in the non-deformed condition, while the cold rolled conditions contained non-uniformly distributed precipitates due to the introduced dislocations. This led to larger precipitate sizes and a reduction in the precipitate number densities in the pre-deformed conditions. HAADF-STEM analysis revealed differences in the fraction of different precipitate types between the non-deformed and the cold rolled conditions. η', η2, and disordered η phase were observed in the non-deformed condition, while η', η2 and the newly identified Y phase were observed in the cold rolled conditions. The disordered η phase contained structural units of the η1 phase and was associated with reducing the lattice misfit between this phase and the Al matrix. Formation of the Y phase was related to an accelerated nucleation rate in the regions of high dislocation density. Graphical abstract

Structural insight into palladium-nickel clusters over mordenite zeolite for carbene-insertion reaction

The advancement of heterogeneous catalysts incorporating metal clusters in the nanometric size range has garnered significant attention due to their extraordinary catalytic activity and selectivity. The detailed characterization and understanding of the atomic structure of these metal clusters within catalysts is crucial for elucidating the underlying reaction mechanisms. In the present study, a distinctive three-atom PdNi cluster, characterized by two Pd atoms at terminal positions and a central Ni atom, was synthesized over mordenite zeolite. The presence of atomic PdNi clusters within the eight-membered ring side pocket area was confirmed by multiple advanced analytical techniques, including magic-angle spinning nuclear magnetic resonance spectroscopy, synchrotron X-ray powder diffraction, extended X-ray absorption fine structure spectroscopy, and high-angle annular dark-field scanning transmission electron microscopy. The catalytic activity of the confined active species was examined by the carbene-mediated reactions of ethyl-2-diazoacetate to ethyl-2-methoxyacetate as a model reaction. Compared to the Pd-mordenite and Ni-mordenite, the PdNi-mordenite catalyst incorporates a PdNi cluster, which demonstrates a superior performance, achieving 100% conversion and high selectivity under the same reaction conditions. Our study elucidates the potential of constructing bimetallic clusters in zeolites, providing valuable insights for developing new heterogeneous catalysts applicable to a wide range of catalytic processes.

Single−atom Co anchored on covalent organic framework for remarkable photocatalytic hydrogen evolution efficiency

Single-atom catalysts (SACs) have attracted extensive attention because of their high atomic utilization and superior catalytic activity. Herein, single-atom Co has anchored on the β-ketoenamine-linked covalent organic framework (Tp-Tta COF) pores and used for remarkable photocatalytic hydrogen(H2) production under Ultraviolet–Visible light (UV–Vis light) irradiation. The single-atom Co is visualized by the aberration-corrected high-angle annular dark-field scanning transmission electron microscopy (AC HAADF-STEM), and the C3–Co–N1 coordination structure is demonstrated by X-ray absorption fine structure (XAFS) measurements. The modified Co0.4-SAC/Tp-Tta COF shows a high photocatalytic H2 production of 1798.5 μmol g−1 h−1 and the Apparent quantum yield(AQY) is 3.02% at 420 nm. The improvement of the activity and stability of the photocatalyst is mainly attributed to the incorporation of Co single-atom that boosts the separation efficiency of photogenerated electron-hole pair and provides well-dispersed active sites. This study provides valuable insights into the development of UV–Vis light-responsive photocatalysts at the atomic level.

RhRu Bimetallic Oxide Cluster Catalysts for Cross-Dehydrogenative Coupling of Arenes and Carboxylic Acids.

Noble-metal-based bimetallic oxide clusters are promising novel catalysts. In this study, we developed carbon-supported RhRu bimetallic oxide clusters (RhRuOx/C) with a mean diameter of 1.2 nm, which showed remarkable catalytic activity for the cross-dehydrogenative coupling (CDC) of arenes and carboxylic acids with O2 as the sole oxidant. RhRu bimetallic oxide cluster formation was confirmed by aberration-corrected high-angle annular dark-field scanning transmission electron microscopy with energy-dispersive X-ray spectroscopy and synchrotron X-ray absorption spectroscopy. Kinetic isotope and substituent effects indicated that arene C-H bond cleavage was the rate-determining step and proceeded via electrophilic concerted metalation-deprotonation mechanism, with a carboxylate as an internal base. Density functional theory calculations supported the proposed mechanism and indicated that the active center for C-H bond activation was Rh(V) rather than Rh(III), while Ru enhanced the electrophilicity of the Rh(V) site by decreasing the negative charge of the surrounding oxygen atoms. Electron-rich arenes showed relatively high reactivity for the RhRuOx/C-catalyzed CDC reaction, and both aliphatic and aromatic carboxylic acids were applicable to the reaction. The RhRuOx/C catalyst is promising for the CDC reaction of arenes and carboxylic acids to produce aryl esters. This work promotes the development of noble-metal-based bimetallic oxide clusters for C-H bond activation reactions.

On the shear strain associated with T1 precipitation in Al-Cu-Li(-Mg-Ag) alloys

The formation mechanism and the distribution arrangements of T1 precipitate plates in peak-aged samples of an Al-4Cu-1.2Li-0.3Mg-0.4Ag (wt.%) alloy are studied using atomic-resolution high-angle annular dark-field (HAADF) and annular bright-field (ABF) scanning transmission electron microscopy (STEM). The formation of a T1 plate of a single unit-cell thickness from the α-Al matrix is found to be associated with a large shear strain that is equivalent to the formation and glide of two different Shockley partial dislocations on two alternate {111}α planes. The T1 precipitate plates tend to cluster into various configurations, including T-shaped and V-shaped configurations comprising two plates of two different T1 variants, and X-shaped configurations consisting of three or four plates of two different variants. The signature of the shear strain is clearly visible in these configurations. A single T1 plate of one unit-cell thickness is elastically distorted in a T-shaped configuration, and the two T1 plates of the same variant in an X-shaped configuration are displaced with respect to each other. Different types of stair-rods are also formed in the intersection of the paired T1 plates in the V-shaped configurations.

A new high-pressure die casting Mg−Gd−Sm−Al alloy with high strength-ductility synergy

A high-pressure die casting (HPDC) Mg−5Gd−1.5Sm−0.7Al alloy was newly developed and exhibits outstanding strength-ductility synergy, with the yield strength and the tensile elongation to fracture being approximately 200 MPa and 8.5%, respectively. This alloy has two types of α-Mg grains: coarse α1-Mg ((46 ± 18) μm) and fine α2-Mg ((9.2 ± 2.3) μm) grains, and various Al-GS (GS = Gd and Sm) particles located at grain boundaries while clear solute-atom segregation near grain boundaries with limited or free intermetallic particles. Characterizations using Cs-corrected high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) indicate the crystal structures of Al-GS phases. After aging, dense β’ precipitates and chain-shaped β’’-like structures precipitated near grain boundaries while a high density of ultrafine β’’-(Mg,Al)3Sm precipitates and Al-GS clusters formed in grain center. Relatively fine grains, Al-GS primary particles, solute-atom segregation near grain boundaries, and/or multiple precipitates contribute to the high strength of the studied alloy, while the multi-scale α-Mg grains, variety of intermetallic particles but discontinuous skeleton, and the multi-typed precipitated lead to its satisfactory ductility.

Ferroelectric behavior arising from polar topologies in epitaxially strained SrTiO3-δ ultrathin films

In this work, we show that epitaxially strained SrTiO3-δ thin films, grown by ion-beam sputtering onto (001)Nb:SrTiO3 substrates, exhibit a ferroelectric behavior. At the atomic-scale, through high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) images, it was possible to identify the presence of polar nanoregions with non-trivial polar topological structures in the SrTiO3-δ film, which are induced through oxygen vacancies. To further confirm the presence of strained regions with a polar structure, Raman spectroscopy and high-resolution X-ray diffraction were employed and it was possible to confirm the presence of a tetragonal structure in the SrTiO3-δ film, with a tetragonality ratio (c/a) of 1.005. Scanning probe microscopy and macroscopic polarization-electric field hysteresis loops show ferroelectric behavior with maximum polarization of ∼1.5 μC/cm2, remnant polarization of ∼0.4 μC/cm2 and coercive field of ∼0.3 MV/cm. This work opens a window for exploring novel polar topological effects in sub-10 nm thin film materials for non-volatile memory application.

Complementary nanodomain structures in topologically close-packed precipitates of Al-Zn-Mg-Cu alloy

High-strength aluminium alloys attract continuous research interest, owing to their wide use in aerospace and terrestrial transportation industries. The performance of the alloys is essentially determined by nanoscale precipitates, thus understanding the structure and formation mechanism of the precipitates during thermal processing is of great importance. Here, we reveal complementary domain structures in precipitates in a high-strength Al-Zn-Mg-Cu alloy using a combination of aberration-corrected high-angle annular dark-field scanning transmission electron microscopy and energy dispersive X-ray spectroscopy. Through the transfer of fivefold symmetry polyhedra at domain boundaries, the intermediate precipitates develop two sets of highly ordered and structurally complementary nanoscale domains in their nucleation and growth. This new type of atom packing maintains the topologically close-packed structure inside the precipitates while reducing the lattice misfit with the Al matrix and the barrier of structural transformations on two interfaces, demonstrating good thermal stability. Our discoveries lead to insight into the precipitate evolution in the Al-Zn-Mg-Cu alloy system and can help understand other precipitation processes of complex structured phases. Furthermore, the evolution process demonstrates an advanced mode of building metastable architectures with nanoscale interlocking pieces in alloy matrixes, which may inspire strategies to obtain high-strength, lightweight and thermostable alloys.

Homogeneous distribution of highly dispersed Pt species over O and P co-doped g-C3N4 and its superior photocatalytic H2 evolution activity

In this study, we synthesized O and P co-doped graphitic C3N4 (OPCN) materials by a one-step calcination method and prepared Pt/OPCN photocatalysts for the photocatalytic H2 evolution reaction. Among the Pt/OPCN catalysts with various O and P contents, Pt/OPCN2 exhibited the highest H2 evolution rate of 2198 μmol·g−1 (AQE = 7.33 %), which was 1.65 times higher than that of Pt/CN (1330 μmol·g−1). Moreover, Pt/OPCN2 demonstrated excellent photocatalytic properties, such as suitable band gap (2.50 eV) for visible light and efficient charge separation of photoexcited electron–hole pairs, which was confirmed by ultraviolet-visible spectroscopy, electrochemical impedance spectroscopy, photoluminescence spectroscopy, and time-resolved photoluminescence measurements. Fundamentally, the Pt species effectively interacted with neighboring PO and CO functional groups that optimally located on defective OPCN2, resulting in a homogeneous formation of highly dispersed PtO evenly distributed over Pt/OPCN2, as confirmed by X-ray photoelectron spectroscopy, high-angle annular dark-field scanning transmission electron microscopy, and density functional theory calculations. However, excessive O and P contents of OPCN3 damaged the morphological structure of g-C3N4, inducing a poor interaction between the Pt species and OPCN3 and forming isolated Pt nanoparticles, resulting in the low photocatalytic activity of Pt/OPCN3.