Cylindrical Shape Research Articles

High-power test results for a cylindrical-shell silicon carbide higher-order-mode damper

The next high-current Electron-Ion Collider (EIC) is a new accelerator to be built at Brookhaven National Laboratory in collaboration with Thomas Jefferson National Accelerator Facility. In the EIC Electron Storage Ring (ESR), there will be beam currents of up to 2.5 A, which will excite massive higher-order-mode (HOM) power in the 17 single-cell 591 MHz superconducting radio-frequency (SRF) cavities. Damping the HOM power in the ESR SRF cavities is a challenge. A room temperature cylindrical shell shape silicon carbide (SiC) beamline HOM absorber (BLA) was chosen as the baseline design, due to its broadband and high-power capability, and previous demonstrations at other accelerator facilities, albeit at much lower power. Because the EIC BLA HOM power dissipation is significantly greater than the previous applications, it is imperative to carry out high-power testing to determine the maximum device performance levels achievable for thermal transport, rf breakdown, and mechanical stress, prior to finalizing the design. A SiC HOM absorber with a state-of-the-art geometry size was prototyped to verify the shrink-fit technique, test outgassing rate, and high-power handling capability. This paper presents the HOM damper’s prototyping and test results. Published by the American Physical Society 2024

Natural and Forced Convective Heat Transfer Enhancement for Solid Cylinders with Different Geometrical Shapes

Enhancing heat transfer for both natural and forced convection is a common issue for any heat transfer process. Experimental studies have been carried out for six different geometrical shapes of solid bars for natural convection and forced convection with four different air velocities while keeping the same perimeter and length of the solid bars, which means the lateral surface area of the bars is the same. Results reveal that both the natural and forced convective heat transfer characteristics are greatly influenced by the geometrical shape in terms of Nusselt number (Nu), heat transfer coefficient (h), and heat transfer rate (q). In addition, isosceles and cylindrical shape geometry contribute to the lowest and highest heat transfer, respectively. As well, it is obtained from the results that convective heat transfer characteristics are directly related to the cross-sectional area, even if the perimeters are the same. Moreover, among the different geometrical shapes, the isosceles and hexagonal shapes take the shortest and longest duration to attain the steady-state condition in the conductive heat transfer process. The convective heat transfer characteristics are well-validated, with available results for both natural and forced convection heat transfer.

Rockfall simulation via spherical harmonic based discrete element method

The trajectory of falling rock is significantly affected by its shape. In order to capture the falling rock shape, spherical harmonic function expansion method is used. The reasonable order of spherical harmonic function expansion items is determined according to the error analysis. Spherical harmonic based discrete element method is utilized to simulate the rockfall process of cylindrical and irregular shape rocks. The influences of the rock and terrain shapes on the rockfall trajectory are analyzed. The results show that the shape of falling rock can be described precisely by spherical harmonic function expansion method, and only a little data should be stored. The predicted trajectory of cylindrical rockfall is close to the experimental result. Spherical and block falling rocks usually show more regular horizontal displacement, lateral offset and jump height during the motion process. Those motion quantities for long strip and flaky falling rocks are more sensitive to their initial rotations. Terrain has a strong influence on rockfall trajectory, falling rocks are prone to move along or rest at mountain valleys.

Ultrasonic dehydration of materials without liquid-vapor transition

This study validates the mechanism of ultrasonic dehydration without transition of water into vapor. The process can be realized by cavitation dispersion of liquid initiated by collapse of cavitation bubbles of cylindrical shape formed in capillaries. The developed mathematical model considers the complete life cycle of cavitation bubbles, encompassing three stages: slow growth, rapid expansion with deformation, and collapse. The optimum range of sound pressure level from 150 dB (critical level) to 170 (limit level) at which cavitation dispersion of liquid from capillaries takes place has been determined. The optimum sample size corresponding to the ultrasonic wavelength in gas, at which the dehydrated productivity is maximized, has been determined. The mechanism of ultrasonic dispersion of liquid during drying was confirmed by experiments. Practical implementation of ultrasonic drying of food products (carrots) confirmed effectiveness of implementation of dehydration mechanism and provided a reduction of drying time by 1.9 times with a reduction of power consumption by 1.7 times.

Review of: "Nanotubes exist in two main categories: single-walled nanotubes and multi-walled MWNTs nanotubes. Single-walled nanotubes can be thought of as high-graphite sheets wrapped in a cylindrical shape"

Review of: "Nanotubes exist in two main categories: single-walled nanotubes and multi-walled MWNTs nanotubes. Single-walled nanotubes can be thought of as high-graphite sheets wrapped in a cylindrical shape"

Fat and fat-free mass measurement agreement by dual-energy X-ray absorptiometry versus bioelectrical impedance analysis: Effects of posture and waist circumference.

Bioelectrical impedance analysis (BIA) operates under the assumption that the conductor has a uniform cylindrical shape. However, this assumption may be violated if measures are taken in the seated position, especially in people with a high waist circumference (WC). The aims of this research were to determine whether posture (supine, standing, and seated) and WC affect agreement between BIA and dual-energy X-ray absorptiometry (DXA) measures of fat mass (FM) and fat-free mass (FFM). Baseline data were collected from 28 adults (mean=61.4±6.9years, 64.3% female) with obesity (BMI 38.6±5.0kg/m2). Body composition was measured using BIA in the supine, standing, and seated positions and by DXA while supine. Intraclass correlation coefficient (ICC) analyses with two-way mixed effects and absolute agreement were performed to determine agreement. Point estimates were excellent for FM and FFM while supine, excellent for FM and good for FFM while standing, and moderate for FM and good for FFM while seated. BIA measures in the supine position resulted in the narrowest 95% confidence intervals compared with other positions. Better agreement was observed across all positions in participants with a WC below the median (118.3cm). Despite the potential pragmatic value of measuring with BIA in a seated position, the results of this analysis demonstrate the poorest agreement between DXA and BIA methods, especially in individuals with high WC. Findings from this study demonstrate that BIA, particularly when measured in a supine position, can serve as a viable alternative to DXA for measuring body composition in people with obesity.

Application of Mass Particle Methods in the Shape Design for Scientific Balloons

This paper proposes a dynamic simulation method for solving balloon shapes. The mass-spring-damping model is used to discretize two-dimensional generatrixes and three-dimensional membrane surfaces, respectively. We solve two-dimensional/three-dimensional ascent shapes at different zero-pressure heights and numerically simulate mushroom cloud shapes that occur during the balloon ground launch. The typical rapid transition feature of the mushroom cloud shape at the waist is depicted. In addition, a preliminary numerical simulation study was conducted for the pumpkin superpressure balloon deployment instability problem. The Calladine instability critical curve for constant angle design lobes is compared and validated for different gore numbers and lobe angles. Further, simulations were carried out on fully inflated shapes of two derived superpressure balloon designs developed by the Japan Aerospace Exploration Agency/Institute of Space and Astronautical Science, namely, the Tawara intermediate cylindrical segment balloon and the diamond-shaped tendon balloon. We verify the ISAS conclusion that the diamond-shaped tendon balloon has a cylindrical shape when fully inflated. Finally, a preliminary simulation study was carried out on the deployment shape of four ballonet architectures in the superpressure balloon. The proposed method for solving various types of balloon shapes based on the mass particle method is simple and efficient, and it has been well applied in our actual balloon engineering.

The genetic basis of apple shape and size unraveled by digital phenotyping.

Great diversity of shape, size, and skin color is observed among the fruits of different apple genotypes. These traits are critical for consumers and therefore interesting targets for breeding new apple varieties. However, they are difficult to phenotype and their genetic basis, especially for fruit shape and ground color, is largely unknown. We used the FruitPhenoBox to digitally phenotype 525 genotypes of the apple reference population (apple REFPOP) genotyped for 303,148 single nucleotide polymorphism (SNP) markers. From the apple images, 573 highly heritable features describing fruit shape and size as well as 17 highly heritable features for fruit skin color were extracted to explore genotype-phenotype relationships. Out of these features, seven principal components (PCs) and 16 features with the Pearson's correlation r < 0.75 (selected features) were chosen to carry out genome-wide association studies (GWAS) for fruit shape and size. Four PCs and eight selected features were used in GWAS for fruit skin color. In total, 69 SNPs scattered over all 17 apple chromosomes were significantly associated with round, conical, cylindrical, or symmetric fruit shapes and fruit size. Novel associations with major effect on round or conical fruit shapes and fruit size were identified on chromosomes 1 and 2. Additionally, 16 SNPs associated with PCs and selected features related to red overcolor as well as green and yellow ground color were found on eight chromosomes. The identified associations can be used to advance marker-assisted selection in apple fruit breeding to systematically select for desired fruit appearance.

A simple three-cylinder radiometer and low-speed anemometer to characterize human extreme heat exposure.

As populations and temperatures of urban areas swell, more people face extreme heat and are at increasing risk of adverse health outcomes. Radiation accounts for much of human heat exposure but is rarely used as heat metric due to a lack of cost-effective and accurate sensors. To this end, we fuse the concepts of a three-globe radiometer-anemometer with a cylindrical human body shape representation, which is more realistic than a spherical representation. Using cost-effective and readily available materials, we fabricated two combinations of three cylinders with varying surface properties. These simple devices measure the convection coefficient and the shortwave and longwave radiative fluxes. We tested the devices in a wind tunnel and at fourteen outdoor sites during July 2023's record-setting heat wave in Tempe, Arizona. The average difference between pedestrian-level mean radiant temperature (MRT) measured using research-grade 3-way net radiometers and the three-cylinder setup was 0.4 3.0°C ( 1 SD). At most, we observed a 10°C MRT difference on a white roof site with extreme MRT values (70°C to 80°C), which will be addressed through discussed design changes to the system. The measured heat transfer coefficient can be used to calculate wind speed below 2m·s-1; thus, the three cylinders combined also serve as a low-speed anemometer. The novel setup could be used in affordable biometeorological stations and deployed across urban landscapes to build human-relevant heat sensing networks.

Interaction of Carbon Nanotubes, Capped Carbon Nanotubes, CNT2–5, C60, C70, HO-C60, [C60]2, and [C60]3 Fullerenes with Virulence Factors of Gram-Negative and Gram-Positive Bacteria: Potential Applications for 3D-Printed Scaffolds

The antimicrobial application of carbon nanomaterials, such as carbon nanotubes (CNTs), capped CNTs, CNT2–5, C60, C70, HO-C60, [C60]2, and [C60]3 fullerenes, is increasing, owing to their low cytotoxicity properties compared to other nanomaterials such as metallic nanoparticles. Enhanced mechanical properties and antibacterial activity can be caused by the incorporation of CNTs in 3-dimensional (3D) printed nanocomposites (NCs). The interruption of the bacterial membrane resulting from the cylindrical shape and high aspect ratio properties has been found to be the most prominent antibacterial mechanism of CNTs. However, the unraveling interaction of CNTs, capped CNTs, CNT2–5, C60, C70, HO-C60, [C60]2, and [C60]3 fullerenes with virulence factors of the main bacterial pathogenesis has not yet been understood. Therefore, in the present study, interactions of these carbon-based nanomaterials with the eight virulence factors, including protein kinase A and (ESX)-secreted protein B of Mycobacterium tuberculosis, pseudomonas elastase and exotoxin A of Pseudomonas aeruginosa, alpha-hemolysin and penicillin-binding protein 2a of Staphylococcus aureus, and shiga toxin 2a and heat-labile enterotoxin of Escherichia coli, were evaluated with the molecular docking method of AutoDock Vina. This study disclosed that the binding affinity was highest for CNT2–5 and [C60]3 toward alpha-hemolysin, with binding energies of −32.7 and −26.6 kcal/mol, respectively. The stability of the CNT2–5–alpha-hemolysin complex at different times was obtained according to the normal mode analysis of ElNémo and iMOD servers.

Energy density source levels of underwater explosive charges

This paper presents experimental measurements of energy density source levels of small explosive charges for high frequencies to 18 kHz. The experiments were carried out using Signals Underwater Sound (SUS) charges deployed at a deep water site in a coastal fiord north of Vancouver BC. The waveform of an underwater explosion is characterized by a high intensity shock wave signal followed by a series of bubble pulses of decreasing intensity. The bubble pulses dominate the SUS energy density spectrum at frequencies below 1 kHz, but at higher frequencies the spectrum is dominated by the characteristics of the decay envelope of the shock wave signal. The explosive material in SUS charges is packed in a thin cylindrical cavity, resulting in a non-uniform decay envelope with secondary pulses when detonated, and a non-spherical distribution of the radiated sound. The impact of the cylindrical charge shape on energy density source level was investigated experimentally. Data were recorded for SUS deployments that generated in-line and broadside sound propagation to the receiver with respect to the axis of the cylindrical charge. Experimental measurements indicate significant differences in the high frequency SUS energy density spectrum depending upon the SUS and receiver geometry.

Spatially uncorrelated two port MIMO DRA using phase gradient PRS for dual directional pattern diversity

This study presents a system utilizing a cylindrical shape ceramic along with a suspended frequency selective surface (FSS), designed for multiple input multiple output (MIMO) applications with dual ports. The proposed antenna system showcases dual pattern diversity properties introducing spatially uncorrelated pattern. Key features of the structured radiator include the arrangement of cylindrical ceramic and the incorporation of an FSS. The alumina ceramic is purposefully placed on the upper part of the dielectric with a joint ground plane. These ceramics are stimulated using circular aperture. To reduce the far-field correlation, FSS with similar phase gradients are placed at the top of DRA at a certain distance. This arrangement yields two distinct radiation patterns from the two ports, ensuring a diverse radiation pattern for the antenna. The proposed technique yields significant improvements, surpassing 10 dB in isolation and achieving a 70% improvement in correlation values. The measured results validate the applicability of this antenna structure for WLAN access point applications within the 5.15–5.35 GHz frequency range.

The Effect of Magnetoelastic Anisotropy on the Magnetization Processes in Rapidly Quenched Amorphous Nanowires.

In this paper, we report for the first time on the theoretical and experimental investigation of Fe77.5Si7.5B15 amorphous glass-coated nanowires by analyzing samples with the same diameters in both cases. The hysteresis curves, the dependence of the switching field values on nanowire dimensions, and the effect of the magnetoelastic anisotropy on the magnetization processes were analyzed and interpreted to explain the magnetization reversal in highly magnetostrictive amorphous nanowires prepared in cylindrical shape by rapid quenching from the melt. All the measured samples were found to be magnetically bistable, being characterized by rectangular hysteresis loops. The most important feature of the study is the inclusion of the magnetoelastic anisotropy term that originates in the specific production process of these amorphous nanowires. The results show that the switching field decreases when the nanowire diameter increases and this effect is due to the reduction in anisotropy and in the intrinsic mechanical stresses. Moreover, the obtained results reveal the importance of factors such as geometry and magnetoelastic anisotropy for the experimental design of cylindrical amorphous nanowires for multiple applications in miniaturized devices, like micro and nanosensors.

First Report of Anthracnose Caused by Colletotrichum gloeosporioides on Cinnamomum camphora in Korea.

Cinnamomum camphora, known as the camphor tree, is an evergreen tree widely cultivated in Asia as an ornamental plant (Singh and Jawaid, 2012). In June 2023, several leaves on a total of 10 trees planted on a street in Suncheon, Jeonnam Province, Korea showed black spots. Disease incidence was observed in at least 15% of the 10 trees. The symptoms included circular spots with a light ash-colored center and dark brown borders. The size of lesions varied depending on the progress of the disease. The disease progressed by 30% on the tree leaves. To isolate the pathogen, we cut out the lesions on the leaf surface sterilized with 70% ethanol for one minute, washed three times with sterilized distilled water, dried, and placed on water agar. Then, it was incubated at 25°C for three days. Emerging hyphae from the samples were subcultured on potato dextrose agar (PDA), resulting in three independent isolates (SYP-F1226-1 to SYP-F1226-3) after single spore isolation from 3 independent trees. The isolates exhibited grayish fluffy mycelium in the center of the colony, while the edges were white on PDA. Conidia had rounded cylindrical shape and were 4.9 to 8.4 µm  1.4 to 3.1 µm (avg. 5.9  2.1 μm, n = 100) in size. Appressoria were round, dark gray, produced at the tip of the germ tube after a septum formed the conidium. The morphological characteristics matched those of Colletotrichum species complexes. (Damm et al., 2012; Weir et al., 2012). For molecular identification, ITS (OR647338 to 40), GAPDH (OR657042 to 44), CHS-1 (OR657045 to 47), ACT (OR657048 to 50), and CAL (OR657051 to 53) sequences from isolates SYP-F1226-1~3 showed a 99.65%, 98.56%, 99.00%, 99.28%, and 99.52% identity with that of type strain C. gloeosporioides ICMP 17821 (JX010152, JX010056, JX009818, JX009531, and JX010445, respectively). Using the MEGA X program (Kumar et al. 2018), maximum likelihood analysis based on the concatenated sequences placed the isolates within a clade comprising C. gloeosporioides. Pathogenicity of SYP-F1226-1 was tested using three leaves from a 1-year-old branch of three independent healthy C. camphora plants. The leaf surfaces were sterilized by rubbing a cotton pad soaked in 70% ethanol and then wiping them with a sterilized cotton pad. The leaves per plant were inoculated with 5 mL of a conidial suspension (1 × 105 conidia/mL), both with and without wounding. Another three control leaves were inoculated with sterile distilled water, both with and without wounding. The inoculated leaves were wrapped in a plastic bag for 48 hours under conditions of 100% relative humidity. Spot symptoms were observed on both wounded and non-wounded leaves 21 days after inoculation. No symptoms were observed in the control on either of the wounded leaves. Pathogenicity tests were performed three times. The pathogen was re-isolated from the lesion after treatment, and its identity was confirmed using the five genes and morphological characteristics. This confirms the fulfillment of Koch's postulates. C. fioriniae (Liu et al, 2022) and C. siamens (Liu et al, 2022; Khoo et al, 2023) have been reported as the causal pathogen of anthracnose in C. camphora, but C. gloeosporioides has not been reported as a pathogen in C. camphora. To our knowledge, this is the first report of anthracnose caused by C. gloeosporioides on C. camphora in Korea. This study will provide symptomatic, mycological, and molecular biological information for the early detection of anthracnose disease in C. camphora plants.

The geometric evolution of aortic dissections: Predicting surgical success using fluctuations in integrated Gaussian curvature.

Clinical imaging modalities are a mainstay of modern disease management, but the full utilization of imaging-based data remains elusive. Aortic disease is defined by anatomic scalars quantifying aortic size, even though aortic disease progression initiates complex shape changes. We present an imaging-based geometric descriptor, inspired by fundamental ideas from topology and soft-matter physics that captures dynamic shape evolution. The aorta is reduced to a two-dimensional mathematical surface in space whose geometry is fully characterized by the local principal curvatures. Disease causes deviation from the smooth bent cylindrical shape of normal aortas, leading to a family of highly heterogeneous surfaces of varying shapes and sizes. To deconvolute changes in shape from size, the shape is characterized using integrated Gaussian curvature or total curvature. The fluctuation in total curvature (δK) across aortic surfaces captures heterogeneous morphologic evolution by characterizing local shape changes. We discover that aortic morphology evolves with a power-law defined behavior with rapidly increasing δK forming the hallmark of aortic disease. Divergent δK is seen for highly diseased aortas indicative of impending topologic catastrophe or aortic rupture. We also show that aortic size (surface area or enclosed aortic volume) scales as a generalized cylinder for all shapes. Classification accuracy for predicting aortic disease state (normal, diseased with successful surgery, and diseased with failed surgical outcomes) is 92.8±1.7%. The analysis of δK can be applied on any three-dimensional geometric structure and thus may be extended to other clinical problems of characterizing disease through captured anatomic changes.

Theoretical modeling of the electronic structure and Fermi surfaces of Gd4Sb3 and GdSb2 compounds

Our theoretical modeling of the electronic structure in the intermetallic Gd4Sb3 and GdSb2 compounds has been done in the framework of density functional theory accounting for spin-orbit coupling. It revealed the metallic character of the summed total density of electronic states for both materials. The complicated Fermi surfaces were found in the half-metallic Gd4Sb3 compound which corresponds to the band structure. The GdSb2 material is obtained to be a bad metal with the low density of states near the Fermi energy, the Fermi surfaces of GdSb2 are found to have the cylindrical shape.

Optimizing transcranial magnetic stimulator coils for minimal influence of individual variability in head geometry

In prior studies focused on transcranial magnetic stimulator (TMS) coils, optimization of coil windings typically occurred on generic curved surfaces, such as planes or cylindrical shapes. However, these surfaces do not consider the challenge of coil misalignment, which arises due to variations in individual head geometries. This misalignment can significantly diminish the coil's effectiveness. To address this issue, we propose a novel coil design approach that identifies the 'best-fit' curved surface, minimizing the likelihood of mismatch with diverse skull geometries. We further enhance the coil winding pattern using the stream function applied to this custom curved surface. Numerical simulations using a hemisphere brain model demonstrate that the coil designed on this 'best-fit' curved surface exhibits a remarkable 22% increase in efficiency and a 41% expansion in stimulation area compared to the conventional butterfly coil. These findings underscore the advantages of our method in crafting high-efficiency and wide-ranging therapeutic TMS coil.

Microfabricated Nitinol Stent Retrievers with a Micro-Patterned Surface.

Stent retrievers are medical devices that are designed to physically remove blood clots from within the blood vessels of the brain. This paper focuses on microfabricated nitinol (nickel-titanium alloy) stent retrievers, which feature micro-patterns on their surface to enhance the effectiveness of mechanical thrombectomy. A thick film of nitinol, which was 20 µm in thickness, was sputtered onto a substrate with a micro-patterned surface, using electroplated copper as the sacrificial layer. The nitinol film was released from the substrate and then thermally treated while folded into a cylindrical shape. In vitro experiments with pig blood clots demonstrated that the micro-patterns on the surface improved the efficacy of blood clot retrieval.

수중에서의 무게추 중량과 수심의 상관성 조사

This study is one of the basic experiments for the development of a weight type water level gauge. The weights are made of polyvinyl chloride (PVC) with a density of 1.1-1.35 g/cm3, in cylindrical shapes of different sizes. The weights come in different diameters: 5, 6, 7, and 8 centimeters, and two different lengths: 20 and 30 centimeters. The weight of the weights was measured using a load cell and the inverse relationship of weight change with increasing depth was investigated. Also, by adjusting the gap between the weight and the outer casing, the distance at which the error in the weight observation due to the surface tension of water of 72.75 dyne/cm (20℃) was not affected was determined. In conclusion, we found that the larger the diameter of the weight and the smaller the height, the better the correlation with the water depth. Also, considering contamination of the PVC weight and manufacturing precision, it was determined that the space between the PVC weight and the external case required more than 1cm. A buoyancy type water level gauge requires the smallest possible weight diameter and sufficient clearance.

Fabrication and Investigation of Deformable Rubber-Carbon Nanotube-Glue Gel-Based Impedimetric and Capacitive Tactile Sensors for Pressure and Displacement Measurements.

Carbon nanotube-glue composite gel-based surface-type elastic sensors with a cylindrical shape deformable (flexible) metallic body were fabricated for tactile pressure and compressive displacement sensing. The fabrication of the sensors was performed using the rubbing-in technique. The effect of the pressure and the compressive displacement on the capacitance and the impedance of the sensors were investigated at various frequencies (in the range of 1 kHz to 200 kHz). It was found that under the effect of pressure from 0 to 9 g/cm2, the capacitance increased by 1.86 and 1.78 times, while the impedance decreased by 1.84 and 1.71 times at the frequencies of 1 kHz to 200 kHz, respectively. The effect of displacement on the impedance and the capacitance of the device was also investigated at various frequencies from 1 kHz to 200 kHz. The results showed that under the effect of compressive displacement up to 25 µm, the impedance of the sensors decreased on average by 1.19 times, while the capacitance increased by 1.09 times, accordingly. The frequency response of the displacement sensor showed that it matched with the low-pass filter. The obtained results are explained based on changes in the shape and geometrical parameters of the cylindrical-shaped conductive body. These results have also been explained on the basis of the distance between the conductive plates of the capacitive sensors during compression, which takes place under the effect of applied pressure or displacement. Moreover, the design of the sensors is simple and easy to fabricate, and their use is also earthy. The fabricated sensors have great potential for commercialization.