Cyclic Mechanical Loading Research Articles

Ion Identification and Ultralow Concentration Sensing with Liquid Flexoelectricity.

The isolation and concentration of electrical charges at ionic-electronic interfaces are prevalent phenomena that impede effective communication between ionic and electronic systems. Detecting these concentrated charges at the interface is crucial for applications, such as signal transmission and ion detection. Current electrical detection approaches introduce additional ionic-electronic interfaces via metallic electrodes with an external stimulating voltage, which alters the initial ion distributions at the interfaces. In this work, we introduce the flexoelectricity of liquids to examine the electrical charge aggregation at ionic-electronic interfaces under cyclic mechanical loads. The measured electrical responses reflect the coupling phenomena between the flexoelectricity and the electric double layer. This proposed approach demonstrates the capability to quantify ion types and concentrations at interfaces. Furthermore, it can identify ion types in mixed solutions and offers high sensitivity at ultralow concentrations. This work promotes a nonchemical, general mechanical method for charge detection at ionic-electronic interfaces.

AN AERODYNAMIC INVESTIGATION OF A HIGH-PRESSURE TURBINE USING ROTOR CASING STATIC PRESSURE MEASUREMENTS AT ENGINE REPRESENTATIVE CONDITIONS WITH DIFFERENT TIP DESIGNS, TIP GAPS AND INLET TEMPERATURE PROFILES

Abstract A rotating High-Pressure (HP) turbine, in modern aircraft engines, is subjected to high cyclic thermal and mechanical loads. Shroudless turbines experience high heat loads on the rotor tip and casing, which makes them one of the life-limiting components for an engine. If the rotor tip starts to erode, then the tip clearance increases which increases the over-tip leakage flow, resulting in reduced stage efficiency and ultimately, the engine lifetime. The Oxford Turbine Research Facility (OTRF) is a high- speed rotating transient test facility that allows unsteady aerodynamics and heat transfer measurements, at engine representative conditions. This paper presents an experimental investigation, of the HP turbine rotor casing aerodynamics, performed in the OTRF. Steady and unsteady casing static pressure measurements were acquired, using pneumatic lines and high-frequency response (∼ 100 kHz) Kulite pressure transducers respectively. The single-stage HP turbine consisted of cooled vanes (featuring film and trailing edge slot cooling), and uncooled rotor blades. Three different tip designs (two squealers and one flat) were tested, at two tip gaps, and with two inlet temperature profiles that included a spatially uniform total temperature profile and an engine representative HP turbine inlet total temperature profile. In parallel, a numerical investigation of the experimental test cases is presented using unsteady Computational Fluid Dynamics (CFD) predictions. The experimental results from this study provide a unique dataset to validate numerical models.

Stress fracture of bone under physiological multiaxial cyclic loading: Activity-based predictive models

While it is known that excessive accumulation of fatigue damage from daily activities contributes to fracture, a model of bone failure under physiologically relevant multiaxial cyclic loading needs to be developed in order to develop effective management strategies for stress or fatigue fractures. The role of strain-induced damage from repetitive loading is a strong candidate for such a model, as cycles of mechanical loading leading to failure can be measured directly. However, this approach has been limited by the restrictions of uniaxial loading models, which often overestimates the fatigue life of bone and suggests that bone will only break well beyond the realistic limits of exercise. To address this gap and develop a physiologically relevant model, our study leverages the power of four commonly used engineering failure criteria as a model for multiaxial loading using a cohort of human tibiae from cadaveric donors (age range 21–85 years old). Four failure criteria (Von Mises, Tsai-Wu, Findley critical plane, and maximum shear strain) were found to be effective in vitro models of tibial fracture when age groups of donors were combined (r2 > 0.84) and stratified (younger: 21–52-years-old versus older: 57–85-years-old) (r2 > 0.83) (p < 0.001). Each failure criterion displayed distinctly lower fatigue curves for the older age group. The maximum shear strain model was used to determine the efficacy of this approach to predict fatigue fractures in humans using published in vivo data from human volunteers. Consistent with in vivo observations in general population, the model demonstrated failure at 5000 to 200,000 loading cycles depending on activities such as jumping, sprinting, and walking, with a 3-fold reduction of fatigue life in older donors. These findings dramatically improve estimates of fatigue life under repetitive loading and demonstrate how age-related changes in bone significantly increase its propensity for fatigue-induced fractures.

Sequential thermomechanical stress and cracking analysis of photovoltaic modules with full and half-cut cells

The transition from conventional full-cell patterns to half-cell modules in the photovoltaic (PV) industry promises enhanced stability and efficiency. This study investigates the thermomechanical behaviour and stress distribution within half-cell and full-cell PV modules during the manufacturing and operational phases. Using finite element modeling, the research simulates sequentially the manufacturing and operating processes such as laser cutting, soldering, lamination, mechanical loading and thermal cycling. The Extended Finite Element Method (XFEM) predicts crack initiation and propagation in the crack-sensitive regions in PV modules during their entire life. Key findings highlight stress concentrations during manufacturing, influenced by parameters like laser power, scribing length and Silicon wafer size. Mechanical loading (ML) and thermal cycling (TC) induce additional stresses, impacting module reliability. The results are useful for the optimization of material properties and the development of advanced design strategies contributing to the durability and efficiency of PV systems.

Impact of Diamond-like Carbon Films on Reverse Torque: Superior Performance in Implant Abutments with Internal Conical Connections

The loosening or fracture of the prosthetic abutment screw is the most frequently reported complication in implant dentistry. Thin diamond-like carbon (DLC) films offer a low friction coefficient and high wear resistance, functioning as a solid lubricant to prevent the weakening of the implant–abutment system. This study evaluated the effects of DLC nanofilms on the reverse torque of prosthetic abutments after simulated chewing. Abutments with 8° and 11° taper connections, with and without DLC or silver-doped DLC coatings, were tested. The films were deposited through the plasma enhanced chemical vapor deposition process. After two million cycles of mechanical loading, reverse torque was measured. Analyses with scanning electron microscopy were conducted on three samples of each group before and after mechanical cycling to verify the adaptation of the abutments. Tribology, Raman and energy-dispersive spectroscopy analyses were performed. All groups showed a reduction in insertion torque, except the DLC-coated 8° abutments, which demonstrated increased reverse torque. The 11° taper groups experienced the most torque loss. The nanofilm had no significant effect on maintaining insertion torque, except for the DLC8 group, which showed improved performance.

The Surface Deterioration of Prefabricated Zirconia Crowns on Exposure to Acidulated Phosphate Fluoride Gel: An In Vitro Study.

Introduction Zirconia is a widely used restorative material in dentistry due to its superior aesthetic and mechanical properties. The oral cavity is a complex ecosystem with various components, which affect the teeth, as well as artificial restorative materials. Various personal and professional interventions carried out can severely affect the properties of restorative materials, thus altering the longevity of the prosthesis; 1.23% acidulated phosphate fluoride (APF) gel is one such professionally applied topical fluoride agent used to prevent caries. The interaction of this APF gel with highly aesthetic restorative material such as zirconia crowns is unknown. Objective The objective of this study is the evaluation of the surface deterioration of prefabricated zirconia crowns on exposure to deionised water and 1.23% acidulated phosphate fluoride (APF) gel with field emission scanning electron microscope (FE-SEM) and mass loss analysis. Material and method Sixty prefabricated paediatric zirconia crowns were taken, 10 samples were immersed in deionised water, 40 samples were immersed in 1.23% APF gel and 10 samples were used ascontrol. Surface morphology and mass loss analysis were carried out at time intervals of four minutes, 24 hours, 48 hours and 72 hours using FE-SEM and digital weighing machine. Results No visual change was observed in the samples immersed in deionised water at the time interval of 72 hours. There was a marked visual change in samples immersed in 1.23% APF gel at the time interval of four minutes to 72 hours; this change involved a loss of gloss to the appearance of chalkiness. FE-SEM analysis for the control group and samples immersed in deionised water showed a smooth, continuous, undisrupted top layer, while samples immersed in 1.23% APF gel showed changes ranging from surface etching, to pinhole porosities, to crack formation and disruption of the surface depending upon the exposure time. Conclusions On the immersion of zirconia crowns in an aqueous acidic medium of 1.23% APF gel, the crowns showed flaws, imperfectionsand uneven superficial layers. It has been observed that surface grains are disrupted and micropores have been formed. This degraded superficial surface when undergoes cyclic mechanical loading can accelerate the ageing phenomenon of zirconia. Mechanical forces along with a dynamic electrochemical environment can degrade the material properties of zirconia.

Crack Length of Elastomeric Sealants and Their Service Life in Contrasting Canadian Climates: Effects of Climate Change.

The longevity of polymer-based sealant and jointing products, including elastomers, significantly depends on the level of exposure to sunlight and joint movement. These factors are particularly crucial in the application of polymers in construction due to their susceptibility to degradation under environmental conditions. For instance, diurnal cycles of contraction and dilation, arising from daily temperature fluctuations, impose significant stress on sealants and joints, impacting their durability over time. The elastic nature of polymeric sealants enables them to endure these cyclic mechanical loads. Athough there is considerable information on sealant durability obtained from laboratory accelerated aging, there is limited knowledge about the effect of climatic factors using historical and projected weather data on the durability and expected service life of these products. This study employed the Shephard crack growth model to predict the performance of sealants in a Canadian context; the crack growth and time-to-failure of hypothetical silicone sealants were investigated across 564 locations, for which historical climate data were obtained from 1998 to 2017, including gridded reanalysis data for the period of 1836-2015. The historical climate data were classified into four climate categories, and crack growth was estimated based on historical climatic data within the valid range for the Shephard model, revealing that locations in colder climates with lower levels of precipitation typically exhibit higher cumulative crack growth. The impact of climatic variation and environmental stressors on the longevity of sealants in the context of climate change was also investigated using future projected data.

Analysis of the destruction of a die insert used in the industrial process of hot die forging to produce a yoke forging

The article performs an analysis of the destruction of forging dies (with two impressions for a double system) used in the industrial process of forging on a hydraulic hammer to produce a yoke forging with a complex geometry. A detailed analysis was performer on one of the lower dies made of non-standard hot chromium-molybdenum-vanadium tool steel, selected for the tests due to its premature damage (a crack) and relatively low durability equalling only 1200 forgings, that is 600 forged elements. Based on the performed complex studies (surface scanning, microhardness tests, microscopic tests, numerical modelling, impact strength trials) it was demonstrated that the most dangerous destruction mechanism for the analyzed process is mechanical cracking and thermo-mechanical fatigue. As a result of the tool working under extreme conditions (high cyclic mechanical impact loads as well as thermal loads), the most intensive damage of the roughing pass, caused by thermal fatigue and abrasive wear, takes place in the areas of complex geometry as well as intensive flow of the forging material on the radii of the roundings. In turn, in the case of the finishing pass, we observe mechanical fatigue cracking of the tool in the areas of stress and high pressure concentration. The results of FEM modelling combined with the results of a microstructural analysis made it possible to determine the causes of the formation of cracks in the working area of the die, which included cyclic high thermal and mechanical loads as well as abrasive wear as a result of intensive flow of the forging material. Within the conducted studies, directions of further investigations were also proposed in order to improve the durability of the examined tool. Additionally, the observed high tendency of the tool material to crack, based on thermal expansion and impact tests and the determination of the crack resistance coefficient K1C, led to the proposal of an alternative material with higher impact strength.

The effect of apparent density of sulfidic crosslink and their chemical nature on self-heat build-up in carbon black filled Natural Rubber under cyclic mechanical loading

Natural rubber is a widely used elastomer for the preparation of cyclically mechanically loaded products such as tires, where it reduces self-heating behavior. From a material point of view, the degree of self-heating depends on the composition of the rubber compound. One of the parameters influencing the self-heating of rubber is the type of curing system, which leads to different crosslinking density. The crosslinking density value for carbon black filled rubbers is only apparent due to the its physical interactions present and is referred to as the apparent crosslinking density (aCLD).Therefore, this work focuses on investigating the effect of sulfur intermolecular network formation by conventional (CV), semi-efficient (SEV) and efficient (EV) curing systems on the temperature development of cyclically loaded rubber using an advanced test method to in-situ determine the heat build-up. Rubber samples based on different curing systems were prepared by varying the concentration of the accelerator N-Tertiarybutyl-2-benzothiazole sulfenamide (TBBS) at a constant concentration of sulfur (2.5 phr). Using basic mechanical tests, it was found that the stiffness and hardness of the rubber increased with increasing aCLD and decreasing proportion of poly-sulfide bonds, respectively. Furthermore, cyclic mechanical analysis showed that with increasing aCLD and parallel decrease in the proportion of poly-sulfide bonds, both the loss modulus (G'') and dissipated strain energy increased, which was also reflected in the values of the mechanical stress-induced self-heating gradient. From the values of maximum developed temperatures, it was evident that the group of material with CV curing system showed the lowest self-heat build-up.

A Computational Model of Mechanical Stretching of Cultured Cells on a Flexible Membrane.

In this work, we created a computational model of the mechanical stretching of cell on a flexible membrane under cyclic mechanical loading. This model provides insight into the forces and displacements inside of cell that result from that application of stretch. As many experiments use this set up, our work is relevant to interpreting many studies that use mechanical stretch to stimulate mechanotransduction.

Critical parameters governing elastocaloric effect in polyisoprene rubbers for solid-state cooling

The aim of this work is to study the critical parameters governing the eCe (elastocaloric effect) of poly-isoprene rubber (NR and IR) in use conditions of a cooling device, i.e. under partial cyclic loading. The effect of mechanical cyclic loading parameters (pre-extension ratio, waveform and frequency) on eCe was first studied. It shows that the eCe increases when the mimimum pre-extension ratio is increased and frequency is lowered from 1Hz to 0.001Hz, as it promotes strain-induced crystallization. However, it also leads to a decrease in potential cooling power, from 7 to 0.01 MW/m3 (i.e. 8 kW/kg to 0.01 kW/kg). At intermediate frequency (f ≈ 0.1 Hz), the comparison of square and triangular waveforms demonstrated that the former enables greater temperature variation. This is due to its holding step (at maximum extension ratio), which maximizes crystallization but also promotes stress relaxation, resulting in increased mechanical losses. Consequently, the square and triangular loadings have a COPmat of 12 and 25, with a temperature variation of 4.2K and 3.6K, respectively. Regarding the formulation, rubbers that do not have a great tendency to crystallize such as synthetic polyisoprene rubber seem to have the best COPmat, while to maximize ΔT, the best of our formulations are NR crosslinked with sulfur and having a crosslink density close to 1.5 × 10−4 mol/cm3, which combine large strain induced crystallization and entropic elasticity. This material has a COPmat of about 27 and allows a ΔT≈4K, i.e.performance comparable to that of the best Shape Memory Alloys (at equivalent COPmat).

Study on the mechanical properties of hydrogels enhanced by acryloyl‐functionalized polyethyleneimine cross‐links

AbstractAppropriate mechanical properties is one of the prerequisites for the applications of hydrogels, where cross‐linker is a crucial component in manipulating such mechanical property. Herein, acryloyl‐functionalized polyethyleneimine (APEI) was innovatively used as novel functional cross‐links to optimize the mechanical properties of polyacrylamide (PAM) hydrogels. APEI cross‐links were synthesized by simply adding acryloyl chloride into polyethyleneimine in aqueous solution. The chemical structures of APEI were confirmed by Fourier transform infrared and nuclear magnetic resonance spectra. APEI possessed massive highly acryloyl functional groups that can serve as multifunctional cross‐linking centers for the polymerization of monomers via covalent bonding interactions. These covalent bonds are favorable for constructing a firm 3D cross‐linked networks for hydrogels to withstand deformations, endowing hydrogels with the improved mechanical properties. The tensile strength with an elongation at break for the hydrogels can reach 234 kPa and 18.4‐fold, respectively. In addition, even the hydrogels can bear cyclic mechanical loads and deformations for 50 cycles at 5‐fold stain, indicating a good fatigue resistance. The deformability of APEI cross‐links clusters under stretching was responsible for the stretchability of PAM/APEI hydrogels. This work provides a simple strategy to enhance the mechanical properties of hydrogels via the development of novel APEI chemical cross‐linker.

A preliminary investigation on the mechanical behaviour of a stiff Italian clay in the context of hydrogen storage

The large-scale use of renewable energy sources is closely linked to the ability to store excess energy generated during periods of overproduction for use when demand is at a peak. Storing green energy is therefore a key component in the move towards a carbon-neutral economy. Underground hydrogen storage in depleted oil and gas reservoirs may provide an efficient long-term solution. Cyclic injection and production of hydrogen alter the chemo-hydro-mechanical conditions of the reservoir and caprocks, and possible geomechanical consequences of such alterations must be preliminarily assessed for safe storage operations. This study aims at exploring the possible effects of cyclic mechanical loads, such as those that might be induced by hydrogen storage and production, on the mechanical behaviour of a clayey caprock. A series of triaxial tests, both monotonic and cyclic, were carried out on undisturbed samples of a stiff Italian clay cored from a caprock formation overlying a hydrocarbon reservoir. The results show that the material response is characterized by the distinctive stress-strain behaviour of stiff clays, with a rather high fragility, which was found to be highly dependent on the loading strain rate. During laboratory experiments conducted at frequencies larger than in situ ones, cyclic loading under stress control causes a gradual degradation of the material structure leading to the formation of a clear shear band followed by a reduction in shear strength. Eventually, failure occurs as the peak shear strength approaches the applied load. The progressive destructuration also implies a reduction in P- and S-wave propagation velocities and a significant change in the signal shape, which is therefore a promising parameter for monitoring the material degradation process.

Effect of Matte-Sn Electroplating Parameters on the Thermo-mechanical Reliability of Lead-free Solder Joints

Most of the Cu/Cu alloy lead-frames of electronic components used for automotive applications contain electroplated matte-Sn terminal finish to improve the wettability of Sn-based Pb-free solders during reflow soldering process. When the solder joints are subjected to combined thermal and mechanical cyclic loading, the influence of matte-Sn electroplating parameters can lead to early and brittle failure of the solder joint. To test this hypothesis, a factorial design of experiments (DOE) has been conducted with LFPAK-MOSFET (hereafter referred to as LFPAK) components plated with different matte-Sn electroplating parameters and reflow soldered with two solder alloys (SAC 305 and Innolot). The LFPAK solder joints were then subjected to thermo-mechanical in-phase cyclic loading under different strain amplitudes. No electrical measurement is done to eradicate the effect of electrical current on the solder joint. The response to the DOE is the crack percentage obtained in the LFPAK solder joints after 1000 and 2000 cycles. The Innolot solder joints exhibited lower crack percentages than the SAC 305. The level of organic additives in the electroplating process of matte-Sn influences the failure mode of the solder joint. Microstructural investigation attributes the nature of failure to the morphology of the (Cu,Ni)6Sn5 IMC phase that forms on the component side of the solder joint.

Cyclic Thermomechanical Loading of Epoxy Polymer: Modeling with Consideration of Stress Accumulation and Experimental Verification.

Developing a viscoelastic model for the cyclic thermomechanical loading of thermosetting polymers is the main goal of this study. The model includes memory for residual thermal stresses and can consider stress accumulation across many loading cycles. By considering stress accumulation, we can improve predictions and understand how thermosetting polymers' stress-strain state changes under cyclic thermomechanical loading. This approach was validated through experimental verification to ensure its applicability in practical engineering scenarios. The experiment showed that the thermosetting polymer can accumulate stress during cycles of heating and mechanical loading during use. The results of the modeling and experiment are compared. The results have led to corrections in the way this model is applied to thermosetting polymers like the epoxy resin in this study. The corrected results matched well with the experimental measurements of stress under cyclic thermomechanical load, with a difference of only 1 to 6%.

Effect of the temporal coordination and volume of cyclic mechanical loading on human Achilles tendon adaptation in men

Human tendons adapt to mechanical loading, yet there is little information on the effect of the temporal coordination of loading and recovery or the dose–response relationship. For this reason, we assigned adult men to either a control or intervention group. In the intervention group, the two legs were randomly assigned to one of five high-intensity Achilles tendon (AT) loading protocols (i.e., 90% maximum voluntary contraction and approximately 4.5 to 6.5% tendon strain) that were systematically modified in terms of loading frequency (i.e., sessions per week) and overall loading volume (i.e., total time under loading). Before, at mid-term (8 weeks) and after completion of the 16 weeks intervention, AT mechanical properties were determined using a combination of inverse dynamics and ultrasonography. The cross-sectional area (CSA) and length of the free AT were measured using magnetic resonance imaging pre- and post-intervention. The data analysis with a linear mixed model showed significant increases in muscle strength, rest length-normalized AT stiffness, and CSA of the free AT in the intervention group (p < 0.05), yet with no marked differences between protocols. No systematic effects were found considering the temporal coordination of loading and overall loading volume. In all protocols, the major changes in normalized AT stiffness occurred within the first 8 weeks and were mostly due to material rather than morphological changes. Our findings suggest that—in the range of 2.5–5 sessions per week and 180–300 s total high strain loading—the temporal coordination of loading and recovery and overall loading volume is rather secondary for tendon adaptation.

O121: Advancing Surgical Innovations: A Novel Approach to Engineering an Off-The-Shelf Bone-Tendon Junction Scaffold Suitable for Transplantation

Abstract Background Musculoskeletal injuries occurring at a staggering rate of 1.7 billion annually, frequently involve the complex bone-tendon junction (BTJ) often due to tear from tendon end due to cyclical strain. Current treatment options, varying from repair to reconstruction usually result in suboptimal outcomes due to structural inconsistencies. Methods In this novel study, we developed comprehensive approach to tackle this clinical challenge. We subjected BTJ tissue harvested from rabbit lower limbs (N=22) to decellularisation process. This involved 5-day demineralisation with 5% formic acid, followed by 8-day proprietary decellularisation method. Further, decellularised bone segments were immersed in Ca-P simulated body fluid for 24 hours to achieve mineral phase and enhance cell attachment. To facilitate recellularisation, adipose-derived stem cells were cultured in differentiating media for 14 days, differentiating into osteoblasts and fibroblasts for bone and tendon segments respectively. Cell phenotype was characterised using cell identification assays. Precise injection of differentiated cells into respective segments was conducted under cyclical mechanical loading with innovative stepper motor device, simulating native tissue physiology. Results Confirmation of effective decellularisation was established through histological characterisation and DNA quantification, with DNA content reduced to &amp;lt;50ng/mg (p&amp;lt;0.05) in bone segment. Successful recellularisation of decellularised scaffold and cell alignment in direction of mechanical load was confirmed through histological analysis on day 5. Comparative analysis revealed similarities in properties between control, remineralised, and recellularised bone, presenting this approach as a promising regenerative technique. Conclusion Our approach offers hope to potentially revolutionise clinical outcomes in this challenging domain by effectively replicating native tissue properties.

Low cycle fatigue behavior and life prediction of a directionally solidified alloy

Low cycle fatigue behavior and life prediction of a directionally solidified alloy

Hydraulic fracturing phase-field model in porous viscoelastic media

The mechanical behavior of shale exhibits pronounced time-dependent nonlinearity. Existing phase-field models are inadequate for evaluating the fluid-driven fracture propagation process in porous viscoelastic media. In this study, a new viscoelastic phase-field model for fluid-driven fracture propagation was introduced based on a thermodynamically consistent framework using the Maxwell–Wiechert model to describe viscoelastic constitutive behavior, with the bulk and shear moduli expanded using the Prony series. Volumetric deviatoric splits were used for both elastic and viscous energies. The fluid flow in both the fracture and the matrix adhered to Darcy's law. Additionally, the phase-field driving force considers the combined influence of rock elastic, viscous, and fluid energies. The numerical calculation iteration format was constructed using finite element discretization and the Newton–Raphson (NR) iterative method. A staggered iteration algorithm was applied to address the displacement, pressure, and phase-field problems. This method not only accurately simulates mechanical cyclic loading but also models the extension of multiple hydraulic fractures in homogeneous reservoirs and hydraulic fracture propagation in fractured reservoirs.

The Development of a 2D Numerical Model of a Device Using the Elastocaloric Effect to Cool Electronic Circuits

The scientific community has been working hard lately to develop fresh, environmentally friendly refrigeration technologies. Those based on solid-state refrigerants are among the Not-In-Kind Refrigeration Technologies that show great promises. The one based on the elastoCaloric Effect is among the most interesting of them. This paper presents the development of a 2D numerical model for a device harnessing the elastocaloric effect with the primary objective of cooling electronic circuits. The study focuses on the intricate interplay between mechanical and thermal aspects, capturing the dynamic behavior of the elastocaloric material in response to cyclic mechanical loading. The numerical model incorporates detailed descriptions of the electronic circuits, accounting for heat dissipation and thermal management. Through simulations, the optimal configuration for efficient cooling is explored, considering various operative conditions and mechanical loading conditions (tensile and bending). The findings contribute to the advancement of elastocaloric cooling technology, offering insights into the design and optimization of devices aimed at enhancing electronic circuit performance through effective thermal control. The results that the most promising configuration is based on bending, a design choice resulting appropriate for cooling the electronic circuits.