Cubic Meters Of Natural Gas Research Articles

Evaluation of Recoverable Hydrocarbon Reserves and Area Selection Methods for In Situ Conversion of Shale

It is well known that the existing horizontal-well-drilling and hydraulic fracturing technology used to achieve large-scale, cost-effective production from immature to low–moderate-maturity continental shale in China, where the organic matter mainly exists in solid form, is fairly ineffective. To overcome the obstacles, in situ conversion technology seems feasible, while implementing it in the target layer along with estimating the amount of expected recoverable hydrocarbon in such shale formations seems difficult. This is because there are no guidelines for choosing the most appropriate method and selecting relevant key parameters for this purpose. Hence, based on thermal simulation experiments during the in situ conversion of crude oil from the Triassic Chang 73 Formation in the Ordos Basin and the Cretaceous Nenjiang Formation in the Songliao Basin, this deficiency in knowledge was addressed. First, relationships between the in situ-converted total organic carbon (TOC) content and the vitrinite reflectance (Ro) of the shales and between the residual oil volume and the hydrocarbon yield were established. Second, the yields of residual oil and in situ-converted hydrocarbon were measured, revealing their sensitivity to fluid pressure and crude oil density. In addition, a model was proposed to estimate the amount of in situ-converted hydrocarbon based on TOC, hydrocarbon generation potential, Ro, residual oil volume, fluid pressure, and crude oil density. Finally, a method was established to determine key parameters of the final hydrocarbon yield from immature to low–moderate-maturity organic material during in situ conversion in shales. Following the procedure outlined in this paper, the estimated recoverable in situ-converted oil in the shales of the Nenjiang Formation in the Songliao Basin was estimated to be approximately 292 × 108 tons, along with 18.5 × 1012 cubic meters of natural gas, in an area of approximately 8 × 104 square kilometers. Collectively, the method developed in this study is independent of the organic matter type and other geological and/or petrophysical properties of the formation and can be applied to other areas globally where there are no available in situ conversion thermal simulation experimental data.

Origin and microbial degradation of thermogenic hydrocarbons within the sandy gas hydrate reservoirs in the Qiongdongnan Basin, northern South China Sea

Large-scale natural gas hydrate accumulations (generally over one billion cubic meters of natural gas) in coarse-grained marine sediments are the most valuable types for commercial exploration and exploitation. The formation of such a gas hydrate deposit generally requires a sufficient natural gas supply such as deeply buried thermogenic gas source. However, the worldwide discovered thermogenic gas hydrate deposits are rare, leaving relatively a poor understanding of their formation and evolution. Based on the geochemical and microbial analyses of eleven hydrate-related gas and five sediment samples from the thermogenic gas hydrate deposits in the Qiongdongnan Basin in northern South China Sea, we systematically investigated the origin and evolution of thermogenic hydrocarbons within sandy gas hydrate reservoirs. Results show that natural gas within high saturated gas hydrate-filled sandy sediments is predominately of thermogenic (the proportion is 57.1–70.5%), characterized by “dry gas” (99.38–99.7% C1, 0.26–0.47% C2 and <0.5% C3+), relatively lower C1/(C2+C3) ratio (187–376), and heavier δ13C–C1 values (−55.0 to −31.3‰). In addition, typical biomarkers (including the alkanes, tricyclic terpanes, hopanes and steranes) generated from mature source rocks were detected in the hydrate-filled fine sand reservoir, as well as the biomarker indicators (including the unresolved complex mixtures (UCMs) hump and the 25-norhopane homologous series) for severe hydrocarbon biodegradation. Furthermore, large amounts of hydrocarbon degrading bacteria (50.5% of bacteria) and methanogenic archaea (34.3% of archaea) were detected within hydrate-filled sandy sediment. Our results indicated that the deeply buried thermogenic source can indeed provide sufficient gas supply for the formation of a large-scale gas hydrate deposit, but thermogenic liquid hydrocarbons within gas hydrate reservoirs are very susceptible to be degraded and consumed by hydrocarbon degrading bacteria. In addition, we also found that the clay components of argillaceous gas hydrate reservoirs can adsorb and store large amounts of in situ immature organic matter, which can significantly obscure or cover up the original geochemical signatures of thermogenic hydrocarbons therein. These findings suggest that the relative contribution of deeply buried thermogenic source for gas hydrate accumulation worldwide may be underestimated, because we have previously ignored the fact that thermogenic hydrocarbons within gas hydrate reservoirs would be significantly consumed by hydrocarbon degrading microbes or diluted by in situ immature sedimentary organic matter. Our findings are highly significant for the evaluation and exploration of thermogenic gas hydrate accumulations worldwide.

ENERGY POTENTIAL OF DISTRIBUTED GENERATION AT POWERFUL BOILER HOUSES OF UKRAINE IN CONDITIONS OF MILITARY AGGRESSION

The Integrated Power System of Ukraine (IPS) is purposefully destroyed by the russian aggressor and suffers significant damage, which has caused long-term emergency interruptions in the power supply of critical infrastructure facilities, enterprises and the population. One of the ways to increase the stability of the IPS of Ukraine is to increase the share of distributed generation in its composition. The conceptual idea of solving this problem is the transformation of existing critical infrastructure objects from electricity consumers into electricity producers/suppliers who will provide their own electricity needs and the needs of other electricity consumers. Boiler houses of centralized heat supply systems (DHS) of Ukrainian cities with their existing electric power and fuel infrastructure can become such objects in wartime conditions. The author proposes the widespread introduction of energy-efficient cogeneration gas-piston units (CGPUs) at boiler houses of the DHS. The container-type CGPU is a typical mass-produced equipment that is manufactured in Ukraine and abroad and has a short implementation period (up to 5 days from the date of delivery to the industrial site of the boiler house). The high maneuverability of the CGPUs allows for an increase the flexibility of the IPS of Ukraine. The article presents the main technical and economic indicators of distributed generation with the use of CGPU at existing boiler houses for further national planning of the development of distributed generation during the martial law and post-war reconstruction of Ukraine. The application of CGPU at boiler houses of the DHS of Ukrainian cities has the potential to provide additional distributed generation with a total capacity of up to 2365.7 MW, in particular, 1224.8 MW at 158 boiler houses with a thermal capacity of 100 Gcal/h and more (612 CGPUs with an average unit electric power of 2.0 MW each); 561.9 MW at 409 boiler houses from 20 to 100 Gcal/h (803 CGPUs of 0.7 MW each); 561.9 MW in 2101 boiler houses from 3 to 20 Gcal/h (4136 CGPUs of 0.14 MW each). Under the conditions of 8 hours a day of use of the installed capacity of CGPUs, 567.8 thousand MWh of electricity will be produced every month at the boiler houses of the DHS (taking into account the consumption of the boiler houses for their own needs and release to the network to other consumers) and 136–142 million cubic meters of natural gas will be consumed. According to the average specific cost of modular CGPU (turnkey supply) from 800 to 950 USD/kW of installed electric capacity, capital costs for implementing the CGPUs with a total capacity of 2,365.7 MW will amount to USD 1.89–2.25 billion. Bibl. 31, Fig. 3.

Technical-Economic Analysis of Energy Efficiency Solutions for the Industrial Steam System of a Natural Gas Processing Plant

Steam, which is primarily employed as a heat transfer medium in process plants, is one of the most widely utilized energy carriers in the industrial sector. One of the factors that affects the cost of steam is how well the condensate collection, steam supply, and return systems of industrial steam systems perform. In a case study, the steam systems of a natural gas processing plant were simulated. The amount of demineralized water loss and, consequently, the identification of various solutions to improve the system were analyzed. The whole steam system was simulated using the MEASUR software platform (v 1.2), and by placing the operational information of the steam system, it was possible to create a baseline for the system, model saving solutions, and finally, provide a technical and economic evaluation of the solutions. Due to the high loss of steam condensate in the SRU steam system (more than 3000 kg per hour), solutions to improve the energy efficiency of the SRU steam system in the form of a maximum recovery of steam condensate (replacement of defective steam traps, redesign of the low-pressure condensate collection network, and high-pressure waste condensate collection) were evaluated with two price assumptions of current energy prices and real prices (the energy saving value of one cubic meter of natural gas is equal to 13 cents). The results show that, for current prices, the investment return period will be between 11.8 and 3.8 months. Moreover, in the main steam system of the refinery (unit 9200), there are three solutions: replacing and repairing defective steam traps, installing an expansion turbine instead of a steam pressure relief valve (PRV), and other solutions (including increasing boiler efficiency, automatic control of the boiler, and energy recovery boiler blowdown) under two price assumptions, the current and real prices of natural gas and demineralized water, were evaluated, and the modeling results show that the investment return period for each of the above solutions at the current prices is 10.2, 186, and 13.3, respectively. The investment return period is based on assuming real fuel and BFW prices are equal to 2.0, 37.6, and 1.7, respectively.

Topical issues of legal regulation of gas production in Russia

The prospects for natural gas on the Russian continental shelf are very significant. According to experts, there are about 55 trillion cubic meters of natural gas on the Russian continental shelf. Most of these reserves are concentrated in the Yamalo-Nenets Autonomous Okrug, where approximately 43.5 % of the total reserves of the Arctic shelf are located. There are also significant reserves of natural gas in other parts of the Arctic shelf, such as the Barents and Kara Seas. Despite the rather complete regulatory framework that governs all stages of natural gas production, from obtaining a license to the environmental component, the system of regulatory legal acts in the field of gas production can be described as quite complex and multi-level. The article deals with the issues of legal regulation of production and processing of natural gas associated with new political and economic challenges. The authors conclude that further systematization of legislation in this area.

Study and application of temporary plugging agent for temporary plugging acid fracturing in ultra-deep wells of Penglai gas field

The burial depth of Penglai gas field reservoir in the Sichuan Basin of China exceeds 7,000 m, and the reservoir temperature is 160°C. Penglai gas field belongs to the fractured reservoir, and there are many natural fractures distributed in the reservoir. Natural fractures are not only the storage place of natural gas, but also the transportation channel of natural gas. Gas wells mainly increase natural gas production through acid fracturing. In the early stage, Penglai Gas Field mainly used gelled acid fracturing technology to create an artificial fracture in the reservoir by injecting a large amount of acid fluid. However, the stimulation range of gelled acid fracturing is very small. After acid fracturing, gas wells can only produce 120,000 cubic meters of natural gas per day. To obtain higher natural gas production, this paper proposes a multi-stage temporary acid fracturing technology that can greatly improve the effect of acid fracturing. The temporary plugging agent for acid fracturing has been developed to meet the high-temperature requirements of the Penglai gas field. Based on the simulation of fracture propagation, the feasibility of acid fracturing expansion of natural fractures in the Penglai Gas Field is clarified. Fiber and granular temporary plugging agents that meet the plugging strength greater than 20 MPa are selected by using the dynamic temporary plugging instrument. MultiFracS software is used to optimize the multi-stage temporary acid fracturing process parameters. The research results in this paper have been applied to wells PS101, PS102, and PS103. After fracturing, compared with the gelling acid fracturing, the natural gas production has increased by more than three times, and the multi-stage temporary plugging acid fracturing has achieved a very good stimulation effect.

Thermo-economic analysis, energy modeling and reconstructing of components of a single effect solar–absorption lithium bromide chiller for energy performance enhancement

This research includes a thermodynamic analysis of a solar absorption chiller due to design temperatures and pressures. Integration of solar energy and absorption chiller in low capacities is done by: static relations (including point-to-point system behavior variations) ruling absorption chillers, calculating the amount of required heat for the generator of the chiller and how it is supplied with, coding and determining optimal chiller coefficient of performance (COP) in Engineering Equation Solver (EES) software, evaluating the affecting factors on the COP by system analysis method. According to the system analysis of a combined solar-chiller system, the best COP is determined to be 0.77; which is a technically acceptable amount in small-size chillers. Also, the computational model for the economic evaluation of energy and energy-saving from receiving solar heat by using a suitable collector shows a 9-year payback period (considering the subsidized price: 0.01$ (2,500 Rails) per cubic meter of natural gas) and a 2-year payback period (considering FOB price equals 0.16$ per cubic meter natural gas). Therefore, it is proven that the economic feasibility of integrating absorption chillers and solar energy is affected by the price of energy carriers in real or subsidiary form and the bank interest rate.

Іncreasing the efficiency of the use of natural gas in household gas stoves

In Ukraine, about a third of the energy is obtained from burning gas (about 30 billion cubic meters of natural gas per year). More than half of this amount of gas is burned in the communal household sector, which includes the population. The largest number of devices intended for burning gas are installed in the population and are household gas stoves used for cooking. The total consumption of gas used by these devices makes up the main part of the gas used in the country in the summer period of the year. In connection with the significant increase in the price of energy carriers and the transition to paying for gas in units of energy, the issue of energy-efficient gas consumption is becoming more and more relevant. In this work, an analysis of the study of the use of gas at different pressures in domestic gas stoves is carried out. A comparison of the efficiency of gas use compared to the use of electrical energy is made. It has been determined that the optimal pressure in front of the gas stove burner, at which combustion has the most economical effect, is 2400 Pa. At this pressure, compared to electrical energy, efficiency increases by 20.8%. When the gas pressure deviates from 2400 Pa, there is a decrease in combustion efficiency, and at a pressure of 1800, the use of natural gas becomes economically impractical (compared to the use of electrical energy for cooking). Combustion of gas, ensuring the necessary completeness of combustion, has a positive effect on the environment as a result of reducing the content of carbon monoxide both in the indoor air of kitchens and in the environment of populated areas. Increasing the energy efficiency of burning natural gas will lead to a decrease in its consumed amount, and as a result, will positively affect the amount of payment for consumed gas, reduce the need for it and increase the level of energy independence of the state.

PEAT IS AN EFFECTIVE ALTERNATIVE FUEL

The article considers peat as an effective alternative fuel. Its reserves and directions of use in the world and in Ukraine presented and analyzed. The analysis showed that the geological reserves of peat in Ukraine are equivalent to 600 billion cubic meters of natural gas. The main reserves of peat are concentrated in the districts of Polissia. Industrial peat extraction can take place in 12 regions: Volyn, Rivne, Zhytomyr, Kyiv, Cherkasy, Poltava, Sumy, Chernihiv, Khmelnytskyi, Ternopil, Lviv, and Ivano-Frankivsk. It has been shown that, compared to traditional energy carriers, peat fuel has a lower heat of combustion and a fairly high ash content, but during combustion it emits almost no toxic substances and, accordingly, pollutes the environment much less. In home furnaces, peat fuel burned with a higher efficiency than coal, and the ash used as fertilizer. The estimated cost of 1Gj of lower heat of combustion of various types of fuel according to the data of recent years shows a noticeable advantage of peat fuels. The cost of thermal energy obtained from burning 1 ton of peat briquettes is 2 times cheaper than when using coal, 3 times cheaper than gas, and 4 times cheaper than fuel oil. Peat fuel is suitable for use in all types of modern solid fuel combustion devices, which increases the prospect of its implementation on the domestic and foreign fuel markets. The technology for using plant biomass as a filler in peat briquettes and granules developed. Special attention paid to wood, buckwheat husk, sunflower and other grain crops, which have a lower ash content and a higher heat of combustion, the potential of which waste is significant, and the fuel characteristics are able to increase the heat of combustion of composite peat briquettes or peat granules and reduce their ash content. Taking into account that peat used in large quantities as fertilizer for agriculture, a technology developed according to which humic substances first removed from peat for fertilizer, and then biomass added to this peat and a composite peat fuel obtained. This technology involves the integration of technology and extraction of humic substances into the production cycle of a peat briquette plant for the production of composite fuel. The wide implementation of the developed technology of composite peat briquettes at peat briquette factories will allow to increase the production of briquettes by almost 2 times without increasing the consumption of peat raw materials and to produce peat fuel in the range of 0.18-0.2% of geological reserves, which is equivalent to the replacement of more than 1 billion m3 of natural gas. All this allows us to draw a conclusion about the positioning of peat fuel as an effective local type of fuel, which is an alternative to gas and coal.

Energy, economic, and environmental (3 E) examinations of the indirect-expansion solar heat pump water heater system: A simulation-oriented performance optimization and multi-objective decision-making

In this paper, a simulation-oriented optimization integrated with the multi-objective decision-making (MODM) model for an indirect-expansion solar-assisted heat pump (IDX-SAHP) water heater is proposed and the energy, economic, and environmental (3 E) aspects of the system are examined. The developed model is verified and its performance is scrutinized in a humid continental climate region of China. Next, the sensitivity analysis is conducted via the one-way analysis of variance (ANOVA) approach. Then, the single-objective optimization (SOO) and multi-objective optimization (MOO) are conducted via the migrating birds optimization (MBO) method to maximize the coefficient of performance (COP) and the collector efficiency (CE), singly and concomitantly. The SOO results indicate the IDX-SAHP design as per the COP-oriented optimization causes the system to operate less for about 120 hours a year in contrast to the system design as per the CE-oriented optimization. Also, the results of MOO integrated with MODM indicate that MOO gives better performance in contrast to the SOOs so that although the CE of the maximized IDX-SAHP reduces a little from 51% to 46%, its COP increases greatly from 2.5 to 7. Therefore, the overall power consumption of the system decreases about 269 hours in contrast to the initial IDX-SAHP. Besides, the environmental examination illustrates the use of IDX-SAHP in Beijing buildings can prevent the burning of 2,877, 000, 000 cubic meters of natural gas per year in the fossil fuel power plants and prevent the release of 8,055,600 tons of CO2 per year into the environment. Furthermore, the economical examination illustrates that Beijing residents may save approximately one billion USD per year on the purchase of electricity if they use the IDX-SAHP. Besides, the Chinese government can achieve about 109 billion USD per year if the equivalent electricity is exported instead of domestic consumption for Electric Water Heaters (EWHs). Moreover, the external costs decrease by 928 million USD per year if the IDX-SAHP is replaced with the EWHs. This paper discloses the significance of energy, economic, and environmental (3 E) examinations, optimization, and MODM during the IDX-SAHP design to increase the system efficiency and decrease the costs and environmental impacts by opting the most appropriate design parameters of the system.

Brief Synopses of New Arabic-Language Publications

Brief Synopses of New Arabic-Language Publications

REGULATORY PROVISION OF SAFETY OF GAS TRANSPORT. CONSTRUKTIONAL DESIGN OF MOBILE COMPRESSOR STATIONS

Problem statement. The basis for the safety and efficiency of the main gas transportation in the world is the tightness of the gas transportation system. A component of the level of industrial safety and efficiency of gas transmission enterprises is the emissions of natural gas into the working area, the environment and the associated costs. Numerous methods of repairing pipeline gas transportation facilities, such as enhancing the bearing capacity of pipelines, repairing defects under gas pressure without interrupting the transportation process, etc., are either not devoid of risks from the point of view of industrial safety, or are energy and resource inefficient. The main type of repair that restores the operable state of the gas transmission system is the replacement of defective equipment, but it is still associated with the release of large volumes of natural gas into the environment. In the second decade of the 2000s, thanks to the rapid development of compressor technology and the invention of a sufficient number of ways to connect compressor units (stations) to main gas pipelines, without stopping the gas transportation process, gas transmission enterprises of the world had a real opportunity to evacuate gas from pipeline sections subject to repair (maintenance ) or accumulate it (control gas pressure in local areas), but the analysis of world experience in the development of gas pressure control technology in localized sections of gas pipelines allows us to assert that there are certain disparities between them in terms of operational safety and the complete absence of regulatory support for the transportation process in Ukraine gas using mobile compressor stations. With this approach to the production process, it is difficult to improve the safety and efficiency of the gas transportation process. The potential for reducing natural gas emissions from the world's gas industry reaches billions of cubic meters of natural gas per year. Purpose of the article. Development of technical requirements for mobile compressor units (stations), which will make it possible to design domestic gas compressor units (stations) capable of safely performing work on pumping natural gas from a localized section of the main gas pipeline to an existing main gas pipeline, within no more than 96 hours, without restrictions on gas supply to consumers. Conclusion. The technical requirements developed by us for mobile compressor units (stations) allow us to design domestic compressor units (stations) capable of safely performing work on pumping natural gas from a localized section of the main gas pipeline to the existing main gas pipeline, within no more than 96 hours, without restrictions on gas supply to consumers.

Recent Developments in Natural Gas Flaring Reduction and Reformation to Energy-Efficient Fuels: A Review

Annually billions of cubic meters of natural gas are flared around the globe at various oil and gas production sites. Natural gas flaring practices waste valuable energy resources that can be used for economic support and will also be beneficial to mitigate global warming effects. In this review, an overview of natural gas flaring impacts with respect to the environment with special emphasis on global annual natural gas flaring emissions and their reformation to energy-efficient fuels has been discussed. Initially, natural gas flaring emissions and their impacts in view of environmental pollution and global warming effects have been highlighted. The strategies to mitigate wastage to valuable energy resources through various flaring management strategies are also evaluated. In the main stream, various gas flaring reductions and utilization technologies based on their applications in the oil and gas industry and especially for remote oil and gas fields are discussed. Liquified natural gas (LNG) and compressed natural gas (CNG) technologies have been identified as the main gas flaring reduction methods based on their applicability, commerciality, and economical potential. In addition, gas to liquid (GTL) has been an advancing technology for the past many years toward its utilization of methane as a feed and converting it to useful industrial products such as synthesis crude and methanol. Finally, reformation technologies for synthesis gas (syngas) production such as thermal reforming, plasma reforming, and photoreforming are deliberated. Based on feed gas mixture, different reforming processes such as steam reforming of methane (SRM), dry reforming of methane (DRM), and bi-reforming of methane (BRM) are evaluated for hydrogen-rich syngas production. The future perspectives regarding gas flaring utilization technologies advancement with further improvements in utilization of flared gas to efficient energy fuels are proposed.

Shale gas potential in China: A production forecast of the Wufeng-Longmaxi Formation and implications for future development

Developing the abundant shale gas in China is a potential means to address the country’s challenges in air pollution and carbon emissions. The purpose of this paper is to evaluate the production potential of the most promising shale gas play—the Wufeng-Longmaxi Formation (WL) in China. We use a Difference-Index analogy method and well-level U.S. shale gas drilling data to estimate the production potential and use a scenario simulation method to propose optimal drilling plans. The results show that the Wufeng-Longmaxi Formation has the potential to produce 70 billion cubic meters of natural gas per year (Bcm/yr), which is 60% of the gas imported into China in 2018. With technology improvement and drilling of more wells, the target of 80–100 Bcm/yr set by the government can be achieved solely by extraction from WL. We find that shale gas drilling is profitable with a well-head price of 1.5 Chinese Yuan per cubic meter. The study indicates that a shale gas boom in China is possible, depending on a more competitive market both upstream and downstream. The successful development of shale gas will change the country’s energy mix to become cleaner and lower-carbon.

A Spatial-Based Integration Model for Regional Scale Solar Energy Technical Potential

One of the main objectives of human society in the present century is to achieve clean and sustainable energy through utilization of renewable energy sources (RESs). In this paper, the main purpose is to identify the locations that are suitable for solar energy in the Kurdistan province of Iran. Initially, solar-related data are collected, and suitable criterion and assessment methods are chosen according to the available data. Then, the theoretical potential of solar energy is assessed and the solar radiation map is prepared. Moreover, the technical potential of various solar technologies is evaluated in that study area. These technologies include concentrating solar power (CSP) and photovoltaic (PV) in power plant applications, and rooftop PV panels and solar water heaters in general applications. The results show that the Kurdistan province has the potential capacity for 691 MW of solar photovoltaic power plants and 645 MW of CSP plants. In the case of using solar water heaters, 283 million cubic meters of natural gas and 1.2 million liters of gasoline could be saved in fuel consumption. The savings in the application of domestic PV will be 10.2 MW in power generation.

Frequencies Rotation at High Sound Pressure Levels Toward Low Frequencies

Today, analyzing of sound pressure level and frequency is considered as an important index in human society. Sound experts believe that analyzing of these parameters can help us to better understanding of work environments. Sound measurements and frequency analysis did to fix the harmful frequency in all sections in Shiraz gas power plant with sound analyzer model BSWA 308. The sound pressure levels (LP) and the one and one-third octave band were continuously measured in A and C weighting networks and slow mode for time response. Excel 2013 and Minitab 18.1 software used for statistical calculations. Results analyzed by Minitab 18.1 software. The highest harmful frequency in Shiraz Gas Power Plant (SGPP) was 50 Hz with 115 dB. The sound pressure level (SPL) ranged from 45 dB to 120 dB in one-third octave band and weighting network C. The maximum sound pressure level was in Craft electricity generator with 105.3 dB and 67 Hz. Sound pressure level in surrounded environment was 120 dB. According to the results, in this industry the sound pressure level exceeded the Occupational Exposure Level of Iran (OEL). The value of sound pressure level were higher than the Standard of occupational health. SGPP consumes 47000 cubic meters of natural gas per hour to produce 100 MW (Mega Watt) of electricity. It is very high and it is not economical and cost effective. These numbers indicate that the power plant’s efficiency is low. It could be concluded that the noise pollution is an important issue in these industries. Moreover, SGPP produce noise with loss energy. Frequencies rotation at high sound pressure levels toward low frequencies were happened.

State-private partnership - the growth factor of gasification of Russian region

The gasification of Russian regions is one of the most important problems for the national economy. The development of the gas supply system contributes to the socio-economic development of the regional economy, to the increase increasing the level and quality of life, and to the solution of the key environmental issues. The Krasnoyarskiy Kray is the only region in the east of the country that has a significant resource potential of natural gas but at the same time, it can’t be connected to the trunk gas pipeline in the short and long term perspective. The purpose of the study is to assess the efficiency of investments in the construction of gas supply facilities, gasification, and their exploitation in the southern and central regions of the Krasnoyarskiy Kray. In this study authors solved the following objectives: we systematized information about the current state of the Krasnoyarskiy Kray gasification and the prerequisites for its development (resource base and transport infrastructure); we assessed economic efficiency of the investments in the construction, gasification, and exploitation of gas supply facilities in the southern and central regions of the Krasnoyarskiy Kray; we formulated proposals to ensure economic efficiency using the mechanism of public-private partnership. The authors recommend an option according to which federal budget investments will amount to 70% of their total investment in the Krasnoyarskiy Kray gasification program. Under this option, the selling price of gas will drop to 4708 rubles per 1000 cubic meters of natural gas excluding VAT. Organization of production, preparation for transport, and transportation of natural gas in the central regions of the Krasnoyarskiy Kray will create new highly paid jobs, significantly increase the GRP, and improve the demographic situation.

Techno-economic assessment and environmental impact of concentrating solar power plants in Iran

This study aims to assess the technical, economic, and environmental aspects of parabolic trough and solar tower power plants under the climatic conditions of south-central regions of Iran with an average direct normal irradiation of about 6 kWh/m2/day. The effects of power plant capacity, cooling system, solar multiple, and hours of thermal energy storage on the techno-economic performance of the power plants are examined. In addition, the environmental metrics including reduction of CO2 emissions, fossil fuel saving, and energy payback time are evaluated. Four power plant capacities of 20, 50, 100, and 200 MWe along with two cooling options, including dry and wet are investigated. Besides, the solar multiple and capacity of thermal energy storage are varied from 1.0 to 4.0 with a step of 0.1, and from 0 to 18 h with a step of 1 h, respectively. The ground weather data from the meteorological organization of Iran are used as input data in the System Advisor Model software. Based on the results, the optimal configurations for the studied power plants concerning the techno-economic parameters are determined. It is revealed that the dry-cooled solar tower power plant with a capacity of 100 MWe, 14 h storage system, and solar multiple of 3.0 is the most efficient configuration under the studied climatic conditions. For this concentrating solar power plant, the levelized cost of electricity and solar-to-electricity efficiency are 11.3 ¢/kWhe and 14.7%, respectively. Furthermore, the energy payback time is about 15 months, annual CO2 emissions reduction is 399 kilotons, and annual fossil fuel saving is 190 million cubic meters of natural gas.

Mastering technology of blast furnace iron smelting using pulverized-coal fuel in the PAO NLMK BF shop № 2

Application of pulverized-coal fuel (PCF) for coke saving is strategic direction of energy costs decreasing for iron smelting in PAO NLMK blast furnaces, which allows to change the structure of coals supply to the plant and to decrease their summarized consumption. Stages of the technology mastering considered, including period of adjusting the PCF preparation and their supplying to the blast furnaces and at the stage of charging system selection and blast regime adjustment ensuring the maximum degree of CO utilization and the specified performance. Analysis of the dynamics of coke consumption and fuel additives showed that the consumption of total carbon fuel remained almost unchanged, despite the difference in the amount of carbon supplied with natural gas and with the PCF. Calculations made by the mathematical model showed that with an increase in the PCF consumption and a decrease in the consumption of natural gas, the replacement rate of coke with natural gas increased by an average of 0.09 kg of coke per 1 cubic meter of natural gas. As a result of the iron smelting technology mastering, in the PAO NLMK BF № 2 a specific coke consumption decrease reached by more than 80 kg/t of iron and natural gas consumption decrease by more than 60 m3/t of iron. The conditions were revealed for the blast furnaces to operate as with minimum coke consumption and with maximum intensity. The blast furnaces operation in the determined regime parameters allow to decrease the fuel costs for iron production.

Analysis of the interannual variability of ice conditions along the route "Sabetta – Murmansk» for the period 1997-2018

«Вестник Санкт-Петербургского университета. Науки о Земле» — научно-теоретический рецензируемый журнал, обобщающий результаты исследований в области геологии, гидрогеологии и геохимии, петрологии и экологии, ландшафтного планирования и геоморфологии, экономической и социальной географии.