Cross Bedding Research Articles

Lithofacies, Facies Association, and Depositional Environment of 34-1, 33-6, and 33-4 Sandstone, Wida Field, Gita Member, Talang Akar Formation, Asri Basin, Offshore Southeast Sumatra

Three Gita Member reservoirs 34-1, 33-6, and 33-4 produce from solution gas drive with rapid pressure decline and low recovery factor. After successful oil production enhancements through waterflooding injections prompt the need for a reservoir model in further field development. Before such models were built reservoir characterization was carried out to determine facies and depositional environment for facies modeling. The study integrated core, wireline log, petrophysical logs, seismic attribute, petrography, etc. Next, well correlation was carried out to distribute stratigraphic markers. Finally, seismic attribute and well correlation were integrated to construct pie chart and depositional environment map. External geometry from seismic attribute revealed distributary channel with point bars which act as reservoir and consist of medium-fine grained planar tabular cross bedding sandstone, mud drapes sandstone, and ripple-wavy lamination sandstone. The wireline log showed fining-upward pattern and core displayed abundant channel rip up clasts, sharp or erosional contact with underlying lithology. Frequent mud drapes found within channel sandstone indicate tidal influence in proximity to marine environment probably in lower delta plain. Channels are trending west-east (34-1) and north-south (33-6 and 33-4). Other facies associations are shallow marine, swamp, interdistributary bay, and tidally influenced interdistributary bay. Shallow marine FA consists of skeletal limestone (Lm), calcareous mudstone, and calcareous sandstone (Sc). Rootlet mudstone (Fb) and interlamination of carbonaceous mudstone with very fine-grain sandstone (Fl) formed interdistributary bay FA. Swamp FA consists of coal and coaly mudstone. Tidally influenced interdistributary bay FA consists of carbonaceous laminated mudstone high in carbon (Flb), intensely bioturbated carbonaceous mudstone (Flb), very finely laminated mudstone-very fine grain sandstone (Fl) and black fissile shale (Fm).

Geochemistry of the North Gondwana Paleozoic Araba and Naqus formation siliciclastics, Sinai: implications for provenance, paleoweathering, and tectonic setting

ABSTRACT The Araba and Naqus formations in Ras Milan, Sinai, constitute part of the major continuous Paleozoic clastic belt stretching across northern Gondwana. They are sandstone-dominated successions, resting on Precambrian granitic basement, with lowermost thin basal polymictic conglomerate deposits (1–2 m), marking the unconformity. The Araba Formation section is composed mainly of varicoloured violet to reddish brown, fine to coarse-grained laminated and planner and overturned cross-bedded sandstones, while the overlying Naqus Formation is characterized by chaotically distributed poorly sorted quartz pebbles to cobbles within a moderately-sorted coarse- to medium-grained quartz arenite and by abundance and variety of large-scale tabular and trough cross bedding. Modal QFL classification of Araba and Naqus formation sandstones revealed that they are merely quartzose sandstones (quartz arenites). Geochemistry of the succession shows extremely wide compositional ranges for almost all major elements, but the Araba Formation is relatively enriched in SiO2, TiO2, Fe2O3*, Na2O, P2O5, and depleted in Al2O3, MgO, CaO and K2O relative to Naqus Formation. Only the Araba Formation samples are depleted in the transition elements Ni, Cr and Co and oppositely possess extreme enrichment in the HFSEs (i.e. Zr, Hf, Y, Nb, Ta, Th, U), whereas both formations show variable depletion in the LILE Rb, K and Ba, and excessive REE abundances relative to the PAAS and UCC, and LREE-enriched patterns with marked negative Eu anomalies. The provenance of the Naqus and Araba formations could be an earlier felsic magmatic source, which has undergone extensive sedimentary recycling. They possess high compositional maturity and were subjected to intensive to moderate weathering during humid climatic conditions. Passive margin tectonic setting is implied which denotes the derivation of Araba and Naqus formation siliciclastics from stable continental regions or plate interiors and deposition in intracratonic basins.

Lacustrine sedimentation by powerful storm waves in Gale crater and its implications for a warming episode on Mars

This investigation documents that the Rugged Terrain Unit, the Stimson formation, and the Greenheugh sandstone were deposited in a 1200 m-deep lake that formed after the emergence of Mt. Sharp in Gale crater, Mars, nearly 4 billion years ago. In fact, the Curiosity rover traversed on a surface that once was the bottom of this lake and systematically examined the strata that were deposited in its deepest waters on the crater floor to layers that formed along its shoreline on Mt. Sharp. This provided a rare opportunity to document the evolution of one aqueous episode from its inception to its desiccation and to determine the warming mechanism that caused it. Deep water lacustrine siltstones directly overlie conglomerates that were deposited by mega floods on the crater floor. This indicates that the inception phase of the lake was sudden and took place when flood waters poured into the crater. The lake expanded quickly and its shoreline moved up the slope of Mt. Sharp during the lake-level rise phase and deposited a layer of sandstone with large cross beds under the influence of powerful storm waves. The lake-level highstand phase was dominated by strong bottom currents that transported sediments downhill and deposited one of the most distinctive sedimentological features in Gale crater: a layer of sandstone with a 3 km-long field of meter-high subaqueous antidunes (the Washboard) on Mt. Sharp. Bottom current continued downhill and deposited sandstone and siltstone on the foothills of Mt. Sharp and on the crater floor, respectively. The lake-level fall phase caused major erosion of lacustrine strata that resulted in their patchy distribution on Mt. Sharp. Eroded sediments were then transported to deep waters by gravity flows and were re-deposited as conglomerate and sandstone in subaqueous channels and in debris flow fans. The desiccation phase took place in calm waters of the lake. The aqueous episode we investigated was vigorous but short-lived. Its characteristics as determined by our sedimentological study matches those predicted by an asteroid impact. This suggests that the heat generated by an impact transformed Mars into a warm, wet, and turbulent planet. It resulted in planet-wide torrential rain, giant floods on land, powerful storms in the atmosphere, and strong waves in lakes. The absence of age dates prevents the determination of how long the lake existed. Speculative rates of lake-level change suggest that the lake could have lasted for a period ranging from 16 to 240 Ky.

Gravity-driven flow in a cross-bedded porous rock

Many geological layers include cross bedding, which leads to different values for permeability along and across the bedding planes. We explore how such cross bedding impacts buoyancy-driven flow through an inclined aquifer. For each bedding angle and ratio of the permeability along and across the bedding, a free buoyancy-driven plume rises at a particular angle to the horizontal. If the angle of inclination of the aquifer to the horizontal is smaller than this angle, then the plume rises along the upper boundary, otherwise, somewhat surprisingly, the buoyant plume rises along the lower boundary of the aquifer. We present new laboratory experiments to support these predictions. We also test a model for the effective permeabilities which control the speed and the rate of spread of the plume along one or other boundary of the aquifer. We consider the impact of our results for modelling geological storage of ${\rm CO}_2$ or aquifer thermal energy storage.

Characterization of pore space in Permo-Triassic sandstone from SW-Germany using the anisotropy of magnetic susceptibility

Pore space in siliciclastic rocks is one of the most important petrophysical properties in geothermal and hydrocarbon reservoir rock characterization. We used the anisotropy of magnetic susceptibility (AMS) of ferrofluid-impregnated Permo-Triassic sandstones of different Buntsandstein and Rotliegend facies as a proxy for pore space anisotropy and preferred flow direction as a case study for reservoir characterization. We compared the calculated ferrofluid porosity (2–21%) with He porosity (2–26%) and permeability (0.002–214 mD) and described the sediment microstructure using petrographic point-counting analysis. For water- and oil-based ferrofluid impregnation, we observed a positive correlation with He porosity and mass and susceptibility impregnation efficiency were used to control the quality of the impregnation process. Triaxial to oblate magnetic rock fabrics were mostly mimicked by the magnetic pore fabrics, except for some of the water-based ferrofluid impregnated samples, where magnetic ellipsoid shapes changed from oblate to prolate. AMS of the unimpregnated sandstones reflects well defined primary sedimentary to diagenetic fabrics with grain imbrication and cross bedding along with more laminated sedimentary structures. Deviation in ferrofluid-impregnated AMS axes orientation can be related either to the low anisotropy < 1.07 in sandstones from the Lower and Upper Buntsandstein, or the low impregnation efficiency. The mimicry is mostly better when the magnetic susceptibility of the sandstone is higher due to a higher concentration of phyllosilicates while micro-porosity is controlled by the clay fabric. A comparison of sediment petrography with magnetic pore fabrics suggests that the pore space is controlled by the bedding of the sandstones with mostly no preferred flow direction within the bedding plane.Graphical

Sedimentary facies and chronological study for a Late Pleistocene sand layer with swash cross bedding within a sand hill at north of Poyang Lake, as inferred from sedimentary structure and optical dating of K-feldspar and quartz grains

Poyang Lake is the largest freshwater lake in China. Currently, there are several sand hills around Poyang Lake and they were mainly interpreted to be formed by aeolian process. However, by field investigation, it is found that several sand/silt layers with parallel bedding, horizontal bedding and swash cross bedding were preserved within sand hills around Poyang Lake. Compared with recent highest water level in Poyang Lake since 1949, the sand/silt layers with parallel bedding, horizontal bedding and swash cross bedding are higher than 22.63m from several meters to more than 10 m. From the view of sedimentary structure, the sand/silt layers mentioned above should be treated as water-lain sediments. In this study, one sand layer with swash cross bedding at elevation of ∼47.5m within a sand hill at north of Poyang Lake was targeted. The bleaching of K-feldspar IRSL signals and quartz OSL signals during their deposition were further investigated by using optical dating techniques. It is found that both K-feldspar IRSL signals and quartz OSL signals were partially bleached and such phenomenon is very different from typical aeolian sediments. The partially bleaching of both K-feldspar IRSL signals and quartz OSL signals is consistent with interpretations by sedimentary structure of the targeted sand layer, i.e. the sand layer with the swash cross bedding within the sand hill should be interpreted as hydraulic sediments and they were not formed by aeolian process. The OSL ages of targeted sand layer were then analyzed by three different methods, i.e. single aliquot MET-pIRIR dating of K-feldspar, single aliquot OSL dating of quartz as well as single grain OSL dating of quartz. The OSL ages of three methods were all consistent with each other and the age results show that the targeted sand layer was formed during MIS 3a. Although previous studies suggested that previous Poyang Lake (Pengli Ze) was initially formed during mid-Holocene, our study indicates that previous Poyang Lake (Pengli Ze) already existed during MIS 3a and it might experience extremely high water level phase at that time.

Development, sand control mechanism and hydrocarbon accumulation of beach-bar sandstone in a saline lake basin: A case from the Neogene of southwestern Qaidam Basin, NW China

Based on the data of field outcrops, drilling cores, casting thin sections, well logging interpretation, oil/gas shows during drilling, and oil/gas testing results, and combined with modern salt-lake sediments in the Qinghai Lake, the Neogene saline lake beach-bars in southwestern Qaidam Basin are studied from the perspective of sedimentary characteristics, development patterns, sand control factors, and hydrocarbon accumulation characteristics. Beach-bar sand bodies are widely developed in the Neogene saline lake basin, and they are lithologically fine sandstone and siltstone, with wavy bedding, low-angle cross bedding, and lenticular-vein bedding. In view of spatial-temporal distribution, the beach-bar sand bodies are stacked in multiple stages vertically, migratory laterally, and extensive and continuous in NW−SE trending pattern in the plane. The stacking area of the Neogene beach-bar sandstone is predicted to be 3 000 km2. The water salinity affects the sedimentation rate and offshore distance of beach-bar sandstone, and the debris input from the source area affects the scale and enrichment of beach-bar sandstone. The ancient landform controls the morphology and stacking style of beach-bar sandstone, and the northwest monsoon driving effect controls the long-axis extension direction of beach-bar sandstone. The beach-bars have a reservoir-forming feature of “one reservoir in one sand body”, with thick beach-bar sand bodies controlling the effective reservoir distribution and oil-source faults controlling the oil/gas migration and accumulation direction. Three favorable exploration target zones in Zhahaquan, Yingdong−eastern Wunan and Huatugou areas are proposed based on the analysis of reservoir-forming elements.

Characteristics, logging identification and major controlling factors of bedding-parallel fractures in tight sandstones

More and more tight oil and gas exploration practices show that bedding-parallel fractures (BPFs) are closely related to hydrocarbon migration and accumulation. However, there is still a lack of studies on the detailed characterization, the logging identification method and the major controlling factors of BPFs. The tight sandstones in the northern Sanbian of Ordos Basin have developed numerous BPFs which are typical research objects. In this study, the development characteristics and oil-bearing of BPFs were firstly analyzed based on cores, thin sections and image logs. Then, constrained by the BPFs appearing in cores and image logs, the identification method of BPFs was established by conventional log curves. Finally, the major controlling factors for the formation of BPFs were discussed. Resultsshow that the oil-bearing of BPFs is markedly better than high-angle fractures (HAFs), which indicates that BPFs have a great significance to tight oil migration and accumulation in the northern Sanbian. The bedding-parallel fractures index (BPFI), which consists of the composite fracture index (CFI), fracture dip index (FDI) and principal component analysis (PCA), can identify the BPFs of tight sandstones, and the identification rate can reach 85% with the detection result of image logs. Fine sandstones with parallel bedding and cross bedding which easily enriched mica, underwater distributary channel sedimentary microfacies with comparatively strong hydrodynamic conditions, and a certain mudstone thickness that can produce differential compaction overpressure are the major factors affecting the development of BPFs.

Lithostratigraphy, lithofacies and deposition conditions of the late Olenekian-middle Anisian Alam Formation in the Nakhlak area, central Iran

The present study aims to investigate petrography characteristics and sedimental environments of upper Olenekian–middle Anisian deposits of Nakhlak group in the sedimentary-structural zone of central Iran. To this end, a section of these deposits with a thickness of 720 meters was first selected, and 190 samples were taken from this section for preparing thin sections. Also, quantitative and qualitative laboratory tests were performed and 25 samples of sandstone were selected for point counter analysis. The results indicated that the major deposits of this formation are related to siliciclastic, carbonate, and pyroclastic types, which are in the form of two facies associations. The facies association A at the bottom of the studied section with the thickness of 90 meters has a periodicity of clastic, carbonate, and pyroclastic facies. The clastic facies of this association consists of fine-grained sandstone. In addition, the carbonate facies in association A are characterized by two microfacies consisting of intraclast oolitic grainstone and oolitic grainstone. Further, tuffite is the only pyroclastic facies related to association A, which has a laminate structure, cross-bedding lamination, herringbone bedding, and upward-thinning and thickening cycles. The facies association, B which is deposited later, is more in the middle and top part of the section. The facies association B is 660 meters thick and has a periodicity of clastic and limestone facies. Clastic facies of this association includes four lithofacies such as conglomerate, pebble coarse-grained sandstone, medium-grained sandstone to thin layer siltstone and shale. The carbonate facies consists of four microfacies such as sandy intraclastic wackestone and mudstone. Furthermore, slumping structures, cross bedding, turbulence, boudinage structure, and convolute of sediments, along with the effects of erosional channels are observed in facies B. Field and laboratory studies conducted on this succession indicate the structure of facies association A was deposited in a mixed siliciclastic carbonate ramp. Finally, submarine canyons and submarine fan environments were left by increasing the depth of the facies association B in the deep part of sea and turbidity systems.

Geological and Erodibility Investigations of Rafin Gora area of Niger State, Northern Nigeria

Abstract Geological, geotechnical and geochemical studies were carried out in Rafi Gora area to ascertain the erodibility of the soils. Medium and coarse-grained sandstone and clay stone were mapped with structures like joints, cross bedding (120/18E and azimuth of 190S), Herringbone, clay clasts, lamina and bioturbation. The sand content of the soils is between 59% and 90%, silt ranges from 18% to 1% and clay constitutes between 9.9% and 32%). Using USDA textural classification, the soils were classified into sand (S), Loamy Sand (LM), Sandy Clay (SC) and Sandy Loam. The soil has a mean pH value of 4.73, average Organic Matter (OM) content of 2.72 and the Coefficient of permeability (K) of 0.90 cm/sec. This k is classified to be within moderately rapid flow (FAO, 2010), an indication of base flows which could result in the collapse of river bank and consequently advance the growth of gullies. Erodibility index (EI) ranges between 0.01 and 0.16 with a significant positive relationship with silt content (0.96), clay content (0.30) and organic matter content (0.20) but significant negative relationship with sand content, pH and permeability. It was advised that excavation of vulnerable claystones by the locals for building construction be totally discouraged. Keywords: Geological, Geotechnical, Geochemical Erodibility index.

Impacts of mineralogy and pore throat structure on the movable fluid of tight sandstone gas reservoirs in coal measure strata: A case study of the Shanxi formation along the southeastern margin of the Ordos Basin

Movable fluid content and permeability are important reference factors for reservoir quality evaluation and recovery enhancement. In this study, based on multiple experimental results, 10 typical samples from a tight sandstone gas reservoir in the coal measure strata of the Shanxi Formation along the southeastern margin of the Ordos Basin were divided into three lithofacies to discuss the factors influencing movable fluid content and permeability. The results show that the fluid has a strong seepage capacity and a high degree of mobility in relatively large pore throats. The relatively large pores in the study area are secondary dissolved pores of various origins. High quartz and feldspar contents are conducive to the formation of secondary pores, while the presence of carbonate minerals and clay minerals play an inhibitory role. The pore throat size range of 0.05–0.1 μm is the critical interval for the conversion of bound fluid to movable fluid. The movable fluid saturation and movable fluid porosity are affected by submicron- and micron-scale pore throats of >0.1 μm, while the permeability is controlled by micron-scale pore throats sizes of >1 μm. The volumetric proportion of the relatively large pore throats is influenced by the mineralogical composition of the rock, the size of the pore throats, and the degree of sorting, which further control the amount of moveable fluid and its percolation capacity. The highest movable fluid content and permeability appear in the massive gravel-bearing coarse to medium sandstone lithofacies (Lm) with a high proportion of submicron- and micron-scale pore throats, whereas the lowest occurs in parallel bedding or ripple laminations，medium to fine sandstone lithofacies (Lpr) with a high proportion of nano-scale pore throats. The lithofacies with cross bedding and medium sandstone (Lc) is also dominated by nano-scale pore throats, which shows the characteristics of low movable fluid content and medium permeability due to the retention of some micron-scale pore throats. This study describes the mobility of fluids with different pore throat sizes in detail and determines the pore throat size range corresponding to the transition from bound fluid to movable fluid, which can provide a reference for the evaluation of movable fluid seepage in other regions.

X- Ray Diffraction Studies of Patti Claystone Member of the Campano-Maastrichtian Patti Formation, Southern Bida Basin, North Central Nigeria

X-ray diffraction and field studies were carried out on the Patti Clay Member of the Patti Formation in the southern Bida Basin. The studies involved field collection of samples and XRD laboratory analysis of clay samples in order to determine the dominant clay type, subordinate associated minerals, geologic processes and paleoenvironment of deposition. Field study involved standard litho-description by noting textural properties, facies type, fossil presence, structure and diagenetic effect. Laboratory XRD analysis procedure included sample grinding, XRD recording condition, selection and measurement of reference minerals, quantification of clay minerals using XRD processing software, XPert-Highscore Plus to generate results indicating clay mineral type and other minerals peaks. Lithostratigraphic section is dominated by the alternation of sandstone and claystone layers. The sedimentary structures are planar parallel and cross bedding in nature. The sandstone at Ahoko and along Lokoja-Abuja highway is characterized by liesegang ring and bioturbation structures. XRD results indicated that the Patti Clay Members are dominated by kaolinite with subordinate illite, montmorillonite and zincite in rare cases. The clay members were suggested to be deposited by moderate to low energy of transportation, moderate to low rate of deposition through prograding mechanism in a marginal marine setting. The kaolinite clay was formed by meteoric water reaction with the shallow-seated clay members through leaching of K+, Na+ and silica ions with resultant kaolinite stable at adequate pH that was not acidic.

Multiscale petrophysical characterization and flow unit classification of the Minnelusa eolian sandstones

Integration of petrophysical and geological information is critical to simulation of subsurface carbon storage (GCS). In this sense, two depositional facies were identified from the core description and well-log interpretation, namely massive (MS) and cross-bedded (CB) facies groups. Additionally, pore-scale characteristics were studied by a combination of techniques, e.g. Nuclear Magnetic Resonance (NMR) and mercury intrusion capillary pressure (MICP). Scanning electron microscope (SEM) and petrographic analyses show that the pore structure is dominantly controlled by the depositional environment and dolomite cementation. NMR-T2 distributions of MS and CB facies show triple and quadruple modes, respectively. In addition, MICP of high- and low-permeability MS facies samples, and their CB facies group mixtures were collected. The MS sample pore-throat size distribution is uni-modal, while the triple-modal characteristic of the mixtures indicates heterogeneous pore structures at the sub-core scale for CB facies. The reliably estimates of porosity and permeability for both facies groups via NMR techniques and the MLR (Multiple Linear Regression) approach demonstrate the applicability of these techniques to eolian sandstone. Moreover, irreducible water saturation via the T2-cutoff method correlates strongly with T2LM instead of porosity. Finally, the rock quality index and flow zone indicator were calculated based on Combinable Magnetic Resonance (CMR) log interpretations. This provides direct connection to properties measured in the well. Four flow units were classified for both facies groups. Results show that better reservoir quality with significant heterogeneities is observed in the CB facies. This study highlights the importance integrating multiscale petrophysical properties including facies, pore architecture and diagenesis analysis with core- to log-scale property characterization. The results herein validate our reservoir characterization and flow unit classification in eolian reservoirs.

Sharp-based, mixed carbonate–siliciclastic shallow-marine deposits (upper Miocene, Betic Cordillera, Spain): The record of ancient transgressive shelf ridges?

Isolated sharp-based sedimentary bodies in shelf settings can develop via the reworking of regressive deposits during transgressions. An example of these are shelf ridges, formed under a wide range of processes, and widely studied due to their high reservoir potential. However, there is still a lack of examples in mixed (carbonate–siliciclastic) successions. This study presents an outcrop example from the Upper Miocene of the Betic Cordillera (Spain), with the aim to propose a model for the development of transgressive sharp-based mixed carbonate–siliciclastic deposits, and to provide criteria to differentiate these from their regressive counterparts. The studied succession is ca. 300 m-thick, and shows a cyclic alternation of coarse and fine-grained mixed deposits. Depositional cycles start with siliciclastic-dominated offshore to offshore transition deposits, progressively replaced by lower shoreface deposits. These are abruptly truncated by sharp erosive contacts bioturbated by passively-infilled large burrows; their ichnological features allow assignation to the Glossifungites ichnofacies. These contacts are interpreted as ravinement surfaces. They are overlain by mixed carbonate–siliciclastic barforms, rich in skeletal fragments and extraclasts, and displaying large-scale cross bedding. These form several m-thick and hundreds of m-long depositional elements interpreted as mixed shelf ridges. These ridges formed in a fine-grained, shallow-water shelf, which occasionally received coarse siliciclastic sediment supply via gravity flows, but had a coeval offshore carbonate factory, which provided the skeletal fragments. The sharp-based, coarser-grained nature and lithological break at the base of these mixed carbonate–clastic deposits could lead to their misinterpretation as forced-regressive wedges. However, the nature of their lower contact, combined with the reworked offshore skeletal fragments, and their stacking pattern are consistent with these mixed units forming during transgression. Other studies in relatively time-equivalent deposits have demonstrated the existence of coeval regressive, coarser siliciclastic-dominated shoreline systems in relatively close localities. These evidence a complex basin configuration in the area during the upper Miocene, with the development of local depocentres and relatively narrow corridors or seaways in the Mediterranean–Atlantic connection, which could have favoured shelf reworking processes, but also promoted the development of diverse stacking patterns, reflecting the differential interaction between active tectonics and sedimentation across the region.

Research on Drilling and Sealing Technology for Cross Bedding of Superthick Coal Seam

Gas disasters have been affecting coal mine safety production. With the gradual deepening of coal resources development, whether gas extraction meets the standard is particularly important. In view of the low extraction efficiency, through theoretical and numerical simulation combined with field measurement, the upper and lower cross bedding drilling is studied. Through the simulation and comparison of gas pressure at different extraction time and the gas pressure changes when the spacing of boreholes is 8 m, 10 m, and 12 m, the results show that, under the designed parameters, when the pressure value at the middle of the two boreholes starts to be less than 0.74 Mpa, the standard extraction time of the upper and lower cross strata boreholes is 160 days, and the most suitable spacing of boreholes is 10 m. Combined with the actual situation of Baode Mine, the extraction effect of cross drilling and parallel drilling was compared. The research shows that the predrainage effect of cross drilling is obviously better than that of parallel drilling. Cross drilling improves the predrainage effect, prolongs the action time of gas extraction by drilling, and effectively eliminates the risk of coal seam outburst.

Depositional and diagenetic controls on reservoir heterogeneity and quality of the Bhuban formation, Neogene Surma Group, Srikail Gas Field, Bengal Basin, Bangladesh

This study aims to investigate the controls on reservoir heterogeneity and quality of Miocene Bhuban Formation of the Neogene Surma Group at the Srikail Gas Field, Bengal Basin, Bangladesh. The study integrates wireline log data from two wells with core description as well as petrophysical and petrographic data obtained from 24 core plug samples retrieved from three gas bearing zones. The three zones, namely (from shallower to deeper): D-upper, D-lower, and E-sands, were identified from wireline log interpretation. Based on the extracted cores, the sandstones are classified into three main facies association: 1) coarse grained facies association (CFA) composed of sandstone with parallel lamination, trough, and planar cross bedding; 2) medium grained facies association (MFA) comprises of wavy and flaser bedded sandstone; and 3) fine grained facies association (FFA) consisting of siltstone and shaly sandstone. CFA sandstones, mostly abundant in D-lower and E-sands, were deposited in a high energy distributary channel environment with strong tidal influence while the finer-grained sandstones, mainly present in D-upper sand, were deposited in a low energy distributary channel. The results obtained by integrating core plugs and wireline logs show that best reservoir quality rocks are associated with CFA sandstones which are characterized by GR below 105 API, 15–25% porosity, and 30–100 mD permeability. In contrast, FFA sandstones have lower porosity (<10%) and higher shale content (GR > 125 API). The high energy and strong tidal influence on sandstones of CFA resulted in coarser grain size (and thus larger pores), better sorting and less clay content than the finer-grained, high clay bearing, low energy sediments of FFA. Additionally, petrographic and core plug analyses revealed that mechanical compaction is an important factor that reduces the porosity and permeability with increasing proportions of ductile mineral grains. Other less important diagenetic factors include quartz overgrowth and cement. The findings of this study show that the reservoir quality of the studied field is principally controlled by both depositional environment and mechanical compaction.

Geology of Zagros metamorphosed volcaniclastic sandstones: a key for changing the Mawat Ophiolite Complex to a metamorphic core complex, Kurdistan Region, NE-Iraq

Mawat Ophiolite Complex is located about 36 km to the northeast of Sulaimani city and directly to the east-northeast of Mawat town near the border of Iran in the northeastern Iraq. The complex has about 600-km2 surface area and consists of high mountain terrains that subjected to intense geological investigations from the fiftieth of previous century till now. According to previous studies, the complex contains tens of igneous rocks such as basalt, metabasalt, tuff, diabase, metadiabase, diorite dykes, periodotite, serpentinite, serpentinite-matrix mélange, gabbro, metagabbro, harzbergite, pyroxenite, plagiogranite, pegmatite, granitiod rocks and dunite. They added occurrences of the volcanic and subvolcanic rocks in the form of dykes or basaltic flows. The present study tries to change the petrology and tectonics of whole complex from Ophiolite Complex to Metamorphic Core Complex. The revision includes refusal of all the above igneous rocks, instead they considered as medium grade regional metamorphism of different types of volcaniclastic sandstones (volcanic wackes), arenites and greywackes (impure sandstones) which sourced predominantly from remote volcanic source area inside Iran. The revision depended on several conjugate field and laboratory evidences inside the complex. These evidences such as absence of pillow basalt, volcanic flows, glass shards, volcanic cones, dykes, sills, contact metamorphism, dilatational structures and flow structures. Other evidences are presence of cross beddings, erosional surfaces, lensoidal channel fills, metamorphosed conglomerate, exposures of thousands of laminated planar beds and transition from fresh volcaniclastic sandstones to its medium grade metamorphosed counterparts, which previously considered as igneous rocks of ophiolite types. Another, evidence, in contrast to ophiolite section, the basalt location is at the base of the claimed ophiolite section while plutonic (dunite and peridotite) rocks located at its top. These locations of the two rocks contradict the definition of ophiolites. Accordingly, the present study changed the geological map of the whole Mawat area from igneous outcrops to metamorphosed volcaniclastic sandstones, arenites and greywackes that belong to Walash-Naoperdan Series. The parent rocks of the series transformed to different types of regionally metamorphosed rocks by deep burial during Eocene. During the burial, diageneses and metamorphisms enhanced by complex mixture of materials from different source areas and seawaters environments. Later, they uplifted, unroofed and exhumed during Pliocene as a core complex.

Re-examining models of shallow-water deltas: Insights from tank experiments and field examples

Shallow-water deltas remain enigmatic in terms of placing the observed facies within a coherent process-based depositional model. Here we report tank experiments on mouth-bar formation from shallow water pure and stratified jets that, combined with recent flume experiments on bedforms, suggest new interpretations of field observations from shallow-water delta outcrops.Our experiments imply that the height, geometry and bedforms of the mouth bars depend on the jet properties and grain size of the supplied sediment. Pure jets with very coarse-grained sediment formed a high and steep mouth bar that is characterised by steep angle-of-repose cross bedding with related avalanche processes (grain flows) on the lee side. The experiments with stratified jets imply that mouth-bar deposition and growth are dominated by supercritical density flows that evolve from the initial jets on the lee side of the growing mouth bar. In stratified jets with very coarse-grained sediment, deposition on the mouth-bar lee side was both from grain-flow avalanches and density flows. While deposition on the upper lee slope was dominated by grain flows, a concentric field of low relief, asymmetric, downflow-migrating bedforms evolved on the lower slope and beyond the mouth bar. In the stratified jet with medium-grained sediment a very low relief mouth bar formed within a concentric field of low, asymmetric, downflow-migrating bedforms covering the entire lee slope and the area beyond.Many previous field studies show that mouth bars deposited from dense stratified jets (hyperpycnal flows) are characterised by a distinct facies assemblage of coarse-grained cross-stratified or low-angle cross-stratified sandstone passing downslope into finer-grained plane-parallel, or “quasi-parallel” laminated sand and into climbing-ripple cross-laminated sandstone. Comparison to flume and tank experiments suggests that the proximal coarse-grained planar and trough cross-stratified sandstones could represent deposition by supercritical dunes that pass downslope into antidunes, characterised by sinusoidal stratification and/or low-angle cross stratification. The repeated vertical transition between antidune deposits and climbing-ripple cross-laminated sandstone may indicate the superposition of ripples onto antidunes in finer-grained sediments, indicating ripple formation under supercritical flow conditions. Similar bedforms/sedimentary structures have previously been interpreted as hummocky cross-stratification or swaley cross-stratification and attributed to combined flows in storm-dominated settings, which probably in some cases must be revised.

Controls of aeolian dune height on cross-strata architecture: White Sands Dune Field, New Mexico, U.S.A.

ABSTRACT The stratal types composing aeolian dunes preserve a record of the transport and sorting of grains and are categorized into: 1) grainflow strata, 2) grainfall laminae, and 3) wind-ripple laminae. The arrangement of these deposits in the cross beds of a formative dune is largely unexplored. Here, field results from White Sands Dune Field, New Mexico, USA, are used to test the hypothesis that dune height controls the arrangement, abundance, and geometry of cross-stratification types. Grainflow thicknesses and deposit widths were measured on wind-scoured stoss-side exposures of seven crescentic dunes with heights ranging from 1.7 m to 11.2 m. Dozens of grainflow thickness measurements were taken along transverse-oriented strata normal to the crest on each dune. The results show that grainflow thickness averages from 1 cm to 4 cm. These data show a positive trend between mean grainflow thickness and dune height but only for the grainflow thicknesses measured at the bases of dunes. The tallest dune (11.2 m) produced many thick grainflow packages of 10 cm to 30 cm in which individual grainflow strata were indistinguishable from each other. This amalgamation was also found to be characteristic of larger dunes—the product of a lack of grainfall deposits separating individual grainflows. These differences in grainflow strata at the bases of dune lee slopes are linked to the temporary storage of sediment along the upper parts of lee slopes. In taller dunes with longer lee slopes, amalgamated grainflows which require multiple avalanche events and take longer time to reach the base transport temporarily stored sediment at upper parts of the slope. This allows time for wind ripples to rework accumulations near the base, where grainfall deposition is also limited. Shorter dunes lack this temporary storage mechanism, as individual grainflows can move across the entire lee slope in a single event, and grainfall accumulates across the entire lee slope. These stratigraphic measurements and process-based understanding will be useful in estimating original dune height in ancient cross-strata and will lead to a better interpretation of aeolian stratigraphy.

Paleoarchean terrestrial to shallow marine sedimentation on Singhbhum Craton, eastern India (the Western Iron Ore Group)

Distinguishing shallow-marine and terrestrial (fluvial) sedimentary deposits is often difficult in the absence of fossils and challenging in deformed and metamorphosed early Precambrian terrains. Herein we report for the first time a > 3.4 Ga shallow marine to terrestrial deposit from the Western Iron Ore Group (WIOG), Singhbhum Craton, India. The WIOG sedimentary succession, lying below a ~ 3.4 Ga banded iron formation, has been divided into three facies associations: a lower alluvial fan-fluvial association, a middle shallow-marine association, and an upper fluvial association. The bottommost conglomerate–very coarse- to coarse-grained sandstone constitutes the alluvial fan-braided fluvial association. Sandstones of the facies association two bears mud drapes and herringbone cross-stratification and thus indicates tidal influence. These shallow-marine sandstones bear wave ripples, ladderback ripples, and adhesion structures and indicate an intertidal depositional environment. The overlying fluvial facies association is characterized by several fining-upward cycles of conglomerate–coarse- to medium-grained sandstones with large-scale trough cross beds, parallel lamination and penecontemporaneous deformation structures and minor shale, indicating the braided nature of the postulated river system. The WIOG succession indicates an overall shallowing-up trend because of sea level fall. The sedimentary structures and texture of the WIOG fluvial deposit are very similar to recent fluvial deposits and are likely to have formed by similar sediment transportation and depositional processes in a tectonically stable sedimentary basin.