Crestal Bone Level Research Articles

Biomechanical behavior of implants with different diameters in relation to simulated bone loss- an in vitro study.

Bone resorption around implants could influence the resistance of the implant abutment complex (IAC). The present in vitro study aimed to assess the stability to static fatigue of implants presenting different levels of bone losses and diameters. Ninety implants with an internal conical connection with 3 different implant diameters (3.3mm (I33), 3.8mm (I38), and 4.3mm (I43)) and 3 simulated bone loss settings (1.5mm (I_15), 3.0mm (I_30), and 4.5mm (I_45) (n = 10)) were embedded and standard abutments were mounted. All specimens were artificially aged (1,200,000 cycles, 50 N, simultaneous thermocycling) and underwent subsequently load-to-fracture test. For statistical analysis, Kolmogorov-Smirnov test, Kruskal-Wallis test, and Mann-Whitney U test (p < 0.05) were applied. All test specimens withstood the artificial aging without damage. The mean failure values were 382.1 (± 59.2) N (I3315), 347.0 (± 35.7) N (I3330), 315.9 N (± 30.9) (I3345), 531.4 (± 36.2) N (I3815), 514.5 (± 40.8) N (I3830), 477.9 (± 26.3) N (I3845), 710.1 (± 38.2) N (I4315), 697.9 (± 65.2) N (I4330), and 662.2 N (± 45.9) (I4345). The stability of the IACs decreased in all groups when bone loss inclined. Merely, the failure load values did not significantly differ among subgroups of I43. Larger implant diameters and minor circular bone loss around the implant lead to a higher stability of the IAC. The smaller the implant diameter was, the more the stability was affected by the circumferential bone level. Preserving crestal bone level is important to ensure biomechanical sustainability at implant systems with a conical interface. It seems sensible to takethe effect of eventualbone loss around implants into account during implant planning processes and restorative considerations.

Correlation of Serum Vitamin D with Crestal Bone Level in Dental Implant Patients Using CBCT: A Clinical Retrospective Study.

The purpose of this study is to correlate the role of serum vitamin D levels associated with crestal bone in dental implant patients using cone-beam computed tomography (CBCT). This retrospective study enrolled patients among whom implants were placed after a detailed planning using CBCT and the delayed loading protocol was followed. After 3 months and 6 months of loading, CBCT evaluations were carried out, serum vitamin D levels were also tested at the end of 6 months of loading. A total of 30 patients were recruited with 15 patients in each group based on normal and deficient levels of vitamin D to correlate with crestal bone levels using CBCT. Clinically acceptable crestal bone loss (CBL) was visible with all the implants at different time intervals. Statistical analysis was done for intergroup and intragroup comparisons which showed significant p-value (< 0.05) for CBL at the time of loading, at 3 months, and at 6 months follow-up for both normal and deficient serum values. In the deficient group, the mean value at baseline was 9.69 mm ± 1.10 and the CBL at 6 months follow-up was 8.80 mm ± 1.10 whereas for the normal group at baseline, the mean was 9.08 mm ± 1.21 and at 6 months follow-up was 8.12 mm ± 1.25 which showed meaningful difference. There is a positive correlation seen between CBL on CBCT and vitamin D serum levels. The success of the implant is significantly affected by vitamin D as it regulates the bone physiology and has systemic effects on accelerating bone formation around titanium implants. Vitamin D is essential in maintaining the balance of bone minerals and assists to preserve the crestal bone level making the implant treatment more predictable and successful.

Immediate versus Delayed Implant Placement in Patients with Tooth Agenesis: An In-Line Retrospective Pilot Study Comparing Clinical and Patient-Related Outcomes

This retrospective study compared clinical, radiological, and patient- and clinician-reported outcomes between immediate and delayed implants placed in patients with tooth agenesis as part of one-stage implant therapy with a split-mouth design. A total of 12 sites of permanent tooth agenesis in five patients received 12 implants (2.4 implants per patient), six being immediate implants in deciduous teeth post-extraction sites, and six being late implants replacing already extracted or spontaneously lost deciduous teeth. Data reporting was performed descriptively without statistical comparative analysis between study groups. Radiographic crestal bone level changes between the time of surgery and 1-year post-surgery did not indicate any marked difference between treatment groups. Patient-reported outcomes related to post-surgical pain and patient preference indicated less pain in immediately treated sites, resulting in a corresponding patient preference related to this treatment modality. Clinician-rated satisfaction levels did not differ. The results of this pilot study support the use of immediate implant placement as a suitable procedure in cases of tooth agenesis.

An Evaluation of the Efficacy and Acceptability of Basal Implants in Traumatically Deficient Ridges of the Maxilla and the Mandible.

Background and objective Rehabilitation of edentulous jaw areas is a complex procedure that has witnessed numerous advancements in technique and materials for better functional and aesthetic outcomes over the years. Dental implants have emerged as a cutting-edge, cost-effective, and non-invasive alternative to traditional removable partial dentures (RPDs), fixed partial dentures (FPDs), and full dentures. In this study, the basal implant was tested in traumatically deficient ridges on the mandible and the maxilla to determine its effectiveness and acceptability. Materials and methods The purpose of this research was to determine whetherbasal implants might be successfully used to restore traumatized ridges in the maxilla and mandible. Eleven individualsaged 20-55 years participated in the trial, and a total of 30 implants were used. All patients were evaluated for pain, soft tissue health around the basal implant, and patient satisfaction, with follow-ups on the third dayand at threeand six months postoperatively. Results The mean pain score measured using the visual analog scale(VAS)of patients during follow-ups was 2.00 ±1.15 on the third day, 0.40 ±0.84 at three months, and 0.00 ±0.00 at six months postoperatively. The mean gingival index score of patients was 1.30 ±0.48 on the third day, 0.10 ±0.31 at three months, and 0.00 ±0.00 at six months postoperatively. The mean patient satisfaction score was 34.77±5.54 on the third day, 41.11 ±6.27 at three months, and 40.7 7±10.91 at six months postoperatively. The mean immediate postoperative marginal bone levelwas 12.33 ±2.26 mm, and it was 10.85 ±2.29 mm after six months postoperatively. The mean preoperative crestal bone level was 10.76 ±1.77 mm and it was 9.70 ±1.79 mm after six months postoperatively. Conclusion Due to the fact that basal implantology does not involve extensive augmentation procedures necessary for the placement of conventional implants, it plays an important role in the rehabilitation of edentulous maxillary and mandibular arches, especially intraumatic, moderate to severely atrophic maxillary and mandibular arches.

Clinical and Radiographic Evaluation of Marginal Bone Level (BL) in Two Implant-Retained Mandibular Overdenture With Lingualized Occlusion (LO): A Six-Year Clinical Trial.

The objective of this research was to assess the marginal bone loss and stability in a lingualized occlusal scheme with implant-supportedmandibular overdenturesas a viable solution for individuals experiencing difficulties with the retention of conventional mandibular dentures. The study assessed the marginal bone level (BL) using radiographic evaluation and clinically by evaluating periodontal health using probing depth indexvalues over a period of 6 years. Ten completely edentulous male patients with a bone height (BH) of 15-25 mm at the mandibular symphyseal region and dissatisfaction with their mandibular conventional complete denture were included in the study. Patients were willing to accept the conditions of the study and provide informed consent. Bleeding index, plaque index (PI), probing depth, and crestal BL were accessed during the follow-up period. Marginal BLs using Wical and Swoop Analysis method were evaluated at baseline (BL) (during loading), 3 yearsand 6 years post-loading. During the observation period, there was no incidence of implant loss, and all patients expressed contentment with the retention, stability, chewing functionality, and esthetic appeal of their dentures.Marginal BLs through clinical and radiographic evaluation, periodontal health using bleeding on probing (BOP), and probing depth were assessed during the follow-up period. Throughout the entire period of observation, no instances of implant displacement were detected. The study found that the use of a lingualized occlusal scheme with two implant-retained mandibular complete overdenture effectively transmitted horizontal loads, reduced stress on individual implants leading to decreased bone loss, and increased stability.

Role of ferroptosis in periodontitis: An animal study in rats.

This study aimed to investigate (1) the temporal pattern of ferroptosis, an iron-dependent cell death, in ligation-induced rat periodontitis and (2) the effect of ferrostatin-1, a ferroptosis inhibitor, on the model. Ferroptosis may contribute to various diseases. However, the role of ferroptosis in periodontitis is still fully understood. In the first experiment, 25 rats with ligation-induced periodontitis were sacrificed on days 0, 1, 2, 7, and 10. Gingivae were obtained to determine tumor necrosis factor (TNF)-α, interleukin (IL)-1β, and ferroptotic biomarkers, including solute carrier family 3 member 2 (SLC3A2) and solute carrier family 7 member 11 (SLC7A11) and glutathione peroxidase 4 (Gpx4), via immunoblotting. Using microcomputed tomography (μCT) and histology, the periodontal soft and hard tissue lesions, including dental alveolar bone crest level, bony characteristics of the surrounding alveolus, periodontal tissue inflammation, and periodontal tissue losses, were evaluated. In study two, 16 rats with induced periodontitis were grouped according to ferrostatin-1 treatment. The rats were intraperitoneally injected with solvent or ferrostatin-1 (1.5 mg/kg/day) 1 day before ligation and sacrificed on days 7 and 10. Gingival protein changes and periodontal tissue damage were also examined. In study one, SLC3A2/SLC7A11 and Gpx4 decreased since day 1; however, TNF-α/IL-1β increased on days 7 and 10. Moreover, the μCT/histology revealed resorptive bony characteristics, inflamed gingival tissue, and periodontal attachment loss. In study two, ferrostatin-1-injected rats exhibited significantly increased SLC3A2/SLC7A11 and Gpx4 but decreased TNF-α/IL-1β than vehicle rats. They also revealed lessened bone resorption, tissue inflammation, and attachment loss. This study highlights the role of ferroptosis, via the system Xc/Gpx4 pathway, in experimental periodontitis and may serve as a regulatory strategy.

Comparison of crestal bone loss and papilla fill after conventional and immediate implant placement: A 12 month clinical and radiographic prospective study.

The problem of missing teeth persists in all age groups. The main objective of implants in dentistry is to provide a restoration that reconstructs the shape and restores esthetics and functions of edentulous areas. The objectives of this study are to compare the crestal bone level changes and papillary fill after placement of implants in fresh extraction socket, i.e. immediate implant placement, and healed extraction socket, i.e. delayed or conventional implant placement, and to assess other clinical parameters such as modified plaque index (mPI), modified gingival index (mGI) and gingival biotype in between the groups and within the groups. 18 patients were recruited in the study out of which 9 patients received implants as per immediate implant placement protocol (group 1) and 9 patients received implants as per conventional implant placement protocol (group 2). All patients were evaluated for gingival biotype, mPI and mGI and papillary fill was assessed as per Jemt's papilla score as clinical parameters. Implant site was assessed for radiographic bone loss using Image J software. Statistical analysis was performed using independent t test, paired t test and chi square test. At the end of 1 year, results showed that crestal bone loss was seen more in the immediate group than the conventional group. Conventional implants showed better papillary fill than implants placed in fresh extraction sockets. Plaque scores were assessed as per modified plaque index, which showed better results in the conventional group. Modified gingival index was used to assess gingival status which showed better results in the immediate group one year later. Findings from the study suggest that crestal bone loss was found to be increased in the immediate group than the conventional group and papillary fill was better in the conventional group than the immediate group.Registration: CTRI ( CTRI/2019/09/021340).

Effect of post-surgical flap position on soft tissue regrowth and keratinized tissue increase following fibre retention osseous resective surgery: a 6-month randomized study with multilevel analysis

BackgroundThe aim of this randomized split-mouth study was to assess the influence of primary flap position on the amount of coronal soft tissue regrowth and keratinized tissue (KT) 6 months after osseous resective surgery with fiber retention technique (FibReORS).Materials and methodsTwo contralateral posterior sextants in 16 patients were treated with FibReORS and randomly assigned to flap positioning either 2 mm below the bone crest (apical group) or at the level of bone crest (crestal group). Clinical parameters were recorded at 1, 3 and 6 months and patient-related outcomes during the first two post-operative weeks.ResultsHealing period was uneventful. Patient’s discomfort was similar in both groups. The overall soft tissue rebound was higher in the apical than in the crestal group (2.0 ± 1.3 mm versus 1.3 ± 0.7 mm), but the difference was statistically significant only interproximally (2.2 ± 1.3 mm versus 1.6 ± 0.8 mm). Multilevel analyses showed higher soft tissue rebound in sites with normal compared to thin phenotype (1.5 mm, p < 0.0001) and treated with flap positioned 2 mm apically to the bone crest (0.7 mm, p < 0.001). An additional 0.5 mm KT increase was observed at interdental sites in the apical group.ConclusionsApical flap positioning increases soft tissue rebound and KT width, mainly at the interdental sites, with reduced patient discomfort.Trial registrationThe trial was registered at ClinicalTrials.gov (ID: NCT05140681, Registration date: 1/12/2021, retrospectively registered).

Efficacy of customized crown-level position jig in measuring peri-implant crestal bone level on periapical radiographs: An in vitro study

Background/purposeAccuracy of using implant length on periapical radiographs as calibration reference for measurements has not been verified. This study aimed to verify the measurements of peri-implant crestal bone level (piCBL) on periapical radiographs taken by the paralleling technique and using the implant length for calibration; and to propose a customized crownlevel position (CLP) jig to improve the measurement accuracy of piCBL. Materials and methodsA typodont installed an implant and a screw-retained crown at maxillary central incisor was used. To simulate piCBL, a metal post was placed near the implant at the same height of implant platform. The CLP jig was designed and 3-dimensionally printed out to allow implant projected orthogonally on periapical film. Thirty periapical radiographs were taken using paralleling technique with and without the jig by three examiners. The implant axis and implant length on radiographs were acquired by image segmentation. The discrepancy of piCBL determination (ΔD) from these measurements were compared and further analyzed when using the implant length for calibration. ResultsThe piCBL measurement errors were smaller when the jig was used for all examiners (P < 0.001). The inter-rater differences were insignificant. After calibration, ΔD with and without jig were 0.09 (0.07–0.11) and 0.43 (0.38–0.49) mm, respectively. ConclusionConventional long-cone paralleling technique using true implant length for calibration demonstrated imprecise piCBL measurement on periapical radiographs. Transferring the implant axis to the CLP jig allowed orthogonal projection of radiography which provided reliable measurements of piCBL with an accuracy of less than 0.1 mm.

Clinico-Radiographic Research Evaluating Crestal Bone Level and Bone Density Surrounding Dental Implants.

Planning the surgical operation, choosing the type of implant, and the effectiveness of the implant all heavily rely on the quantity and quality of the accessible bone. This study's goal was to determine how promptly inserted dental implants affected postoperative changes in bone density and crestal bone level by Cone bean computed tomography (CBCT) gray-scale value during a follow-up of three to six months. A prospective clinical-radiographic investigation was conducted. Twenty participants with a partly edentulous arch who were also systemically healthy were chosen from the OPD of the Department of Periodontics and Oral Implantology. Each patient's oral hygiene status was noted, and a preoperative CBCT was performed to assess bone density. The following clinical parameters were noted before surgical procedures: plaque index (PI) (Silness and Loe, 1964), gingival index (GI) (Loe and Sillness, 1964), probing pocket depth (PPD), and primary stability. A weak connection between Hounsfield unit (HU) in three months and six months was found. Moreover, a slender positive connection between baseline primary stability and three months was found. PI was shown to have a statistically significant difference between the means at several follow-ups (P value of 0.0001). PI and probing depth were not statistically different between baseline and six months (P values = 0.0001) or between three months and six months (P values = 0.050), respectively. The main outcome of this study shows that insertion torque is directly proportional to bone density and crestal bone level.

Comparison between Measurements of Clinical Attachment Level and Transgingival Probing with Alveolar Bone Crest Level in Chronic Periodontitis Patients

Background: Periodontitis is an inflammatory disease of the supporting tissues of the teeth that leads to crucial changes in the bony architecture. Early detection is of great practical significance so that treatment may be administered before irreversible destruction could occur. Differences exist between different diagnostic methodology concerning the relationship between the measurements and the level of the lesion. The aim of this study was to assess relationship between clinical attachment level (CAL) and alveolar bone crest level (ABCL), reliability of transgingival bone probing level (TBL) for ABCL measurement, and clinical biologic width (CBW) measurement in chronic periodontitis patients. Methods: An analytical cross-sectional study was conducted on 238 periodontal sites in 25 chronic periodontitis patients, aged 20–60 years who were planned for periodontal flap on residual pocket depth of 5-8mm after four weeks of non-surgical therapy. Stent was used for coronal fixed reference point. The relative attachment level (RAL), relative transgingival bone probing level (RTBL), relative alveolar bone crest level (RABCL), and CBW were measured at six sites per tooth excluding third molars. Descriptive and inferential statistical analysis was done. Probability of significance (p-value) was set at 5%. Results: Overall RAL, RTBL and RABCL (mean ± SD) were 8.08 ± 1.23, 10.82 ± 1.1, and 11.15 ± 1.36 mm respectively. Overall CBW (mean ± SD) was 3.06 ± 0.634 mm. Conclusions: There was a significant positive correlation of CAL and TBL with ABCL. Also, the CBW was greater than that of standard histologic BW.

The Potential of a Saliva Test for Screening of Alveolar Bone Resorption.

Oral health screening is important for maintaining and improving quality of life. The present study aimed to determine whether patients with a certain level of alveolar bone resorption could be screened by salivary bacterial test along with their background information. Saliva samples were collected from 977 Japanese patients, and the counts of each red-complex, that is, Porphyromonas gingivalis, Treponema denticola, and Tannerella forsythia, were measured using quantitative polymerase chain reaction analysis. Mean bone crest levels (BCLs) were measured using a full-mouth periapical radiograph. Multiple logistic regression analysis was used to determine associations between BCLs (1.5-4.0 mm in 0.5 mm increments) and explanatory variables, such as the number of each red-complex bacteria and the patients' age, sex, number of teeth, stimulated saliva volume, and smoking habits. When the cutoff BCL value was set at 3.0 mm, the area under the curve, sensitivity, and specificity values were optimal at 0.86, 0.82, and 0.76, respectively. In addition, all tested explanatory variables, except sex and T. denticola count, were significantly associated with BCLs according to a likelihood ratio test (p < 0.05). Additionally, the odds ratio (OR) was substantially increased when a patient was >40 years old and the bacterial count of P. gingivalis was >107 cells/µL (OR: >6). Thus, P. gingivalis count and patients' background information were significantly associated with the presence of a certain amount of bone resorption, suggesting that it may be possible to screen bone resorption without the need for radiography or oral examination.

Influence of disclusion time reduction on changes in posterior implant prosthesis occlusion and its association with crestal bone loss: A clinical study

Statement of problemA prolonged period of high magnitude occlusal contact can be associated with rapid changes of the occlusal surfaces and, in turn, may lead to overloading of an implant-supported prosthesis. Crestal bone loss may be one of the repercussions of overloading, but the influence of disclusion time (DT) reduction (DTR) is unclear. PurposeThe purpose of this clinical study was to evaluate the role of DTR in preventing the occlusal changes and crestal bone loss at progressive time intervals of 1 week, 3 months, and 6 months in posterior implant-supported prostheses. Material and methodsTwelve participants with posterior implant-supported prostheses and opposing natural teeth were enrolled in the study. Occlusion time (OT) and DT were evaluated with the T-scan Novus (version 9.1). By performing immediate complete anterior guidance development (ICAGD) coronoplasty, prolonged contacts were selectively ground to achieve OT ≤0.2 seconds and DT ≤0.4 seconds in maximum intercuspal position and laterotrusion after cementation and during follow-up visits after 1 week, 3 months, and 6 months. Crestal bone levels were evaluated after cementation and at the 6-month follow-up. Repeated measures ANOVA and Bonferroni post hoc analysis were done for OT and DT. Student paired t test was done for crestal bone level evaluation (α=.05 for all tests). ResultsA significant decrease in OT from 0.59 ±0.24 seconds to 0.21 ±0.06 seconds (P<.001) and in DT from 1.51 ±0.6 seconds to 0.37 ±0.06 seconds (P<.001) were detected in posterior implant-supported occlusion immediately after attaining ICAGD and at the 6-month follow-up period. The mean crestal bone levels at the mesial and distal sides of the implant from day 1 (0.4 ±0.13 mm, 0.36 ±0.20 mm) to 6 months (0.40 ±0.13 mm, 0.37 ±0.19 mm) showed no significant changes (P>.05). ConclusionsMinimal occlusal changes in implant prosthesis and negligible crestal bone loss were observed up to 6 months by achieving DTR according to the ICAGD protocol.

Effect of crown stiffness and prosthetic screw absence on the stress distribution in implant-supported restoration: A 3D finite element analysis.

This in-silico investigation evaluated the mechanical impact of Morse tape implant-abutment interface and retention system (with and without screw) and restorative materials (composite block and monolithic zirconia) by means of a three-dimensional finite element analysis (3D-FEA). Four 3D models were designed for the lower first molar. A dental implant (4.5 × 10 mm B&B Dental Implant Company) was digitized (micro CT) and exported to computer-aided design (CAD) software. Non-uniform rational B-spline surfaces were reconstructed, generating a 3D volumetric model. Four different models were generated with the same Morse-type connection, but with a different locking system (with and without active screw) and a different crown material made of composite block and zirconia. The D2 bone type, which contains cortical and trabecular tissues, was designed using data from the database. The implants were juxtaposed inside the model after Boolean subtraction. Implant placement depth was simulated for the implant model precisely at crestal bone level. Each acquired model was then imported into the finite element analysis (FEA) software as STEP files. The Von Mises equivalent strains were calculated for the peri-implant bone and the Von Mises stress for the prosthetic structures. The highest strain values in bone tissue occurred in the peri-implant bone interface and were comparable in the four implant models (8.2918e-004-8.6622e-004 mm/mm). The stress peak in the zirconia crown (64.4 MPa) was higher than in the composite crown (52.2 MPa) regardless of the presence of the prosthetic screw. The abutment showed the lowest stress peaks (99.71-92.28 MPa) when the screw was present (126.63-114.25 MPa). Based on this linear analysis, it is suggested that the absence of prosthetic screw increases the stress inside the abutment and implant, without effect on the crown and around the bone tissue. Stiffer crowns concentrate more stress on its structure, reducing the amount of stress on the abutment.

Estimating Crestal Thickness of Alveolar Bones on Intra-oral Ultrasonograms.

Alveolar crestal bone thickness and level provide important diagnostic and prognostic information for orthodontic treatment, periodontal disease management and dental implants. Ionizing radiation-free ultrasound has emerged as a promising clinical tool in imaging oral tissues. However, the ultrasound image is distorted when the wave speed of the tissue of interest is different from the mapping speed of the scanner and, therefore, the subsequent dimension measurements are not accurate. This study was aimed at deriving a correction factor that can be applied to the measurements to correct for discrepancy caused by speed variation. The factor is a function of the speed ratio and the acute angle that the segment of interest makes with the beam axis perpendicular to the transducer. The phantom and cadaver experiments were designed to validate the method. The comparisons agree well with absolute errors not more than 4.9%. Dimension measurements on ultrasonographs can be properly corrected by applying the correction factor without recourse to the raw signals. The correction factor has reduced the measurement discrepancy on the acquired ultrasonographs for the tissue whose speed is different from the scanner's mapping speed.

Non-surgical treatment of peri-implantitis with and without erythritol air-polishing a 12-month randomized controlled trial

BackgroundA variety of interventions have been explored in the non-surgical management of peri-implantitis. In spite of extensive testing of various study protocols, effective treatments largely remain unavailable. The objective of the present 12-month single-centre, examiner-masked, randomized controlled clinical trial was to explore whether a low-abrasive erythritol air-polishing system produces added clinical benefit when used adjunctive to conventional non-surgical management of peri-implantitis and to record any associated patient-centered outcomes.MethodsForty-three patients with mild to severe peri-implantitis including at least one implant either received ultrasonic/curette subgingival instrumentation and erythritol air-polishing (test) or ultrasonic/curette instrumentation only (control) at baseline and at 3, 6, 9, and 12 months. Probing depth (PD), bleeding on probing (BoP), dental plaque, suppuration (SUP), crestal bone level (CBL), and peri-implant crevicular fluid (PCF) were recorded at baseline, 6 and 12 months. Visual Analogue Scale (VAS) scores were collected immediately following subgingival interventions at all time-points.ResultsA reduction in PD was observed from baseline to 6 months for the test (p = 0.006) and control (p < 0.001) and from baseline to 12 months for the control (p < 0.001). No intergroup differences were observed for primary outcome variables PD or CBL over time (p > 0.05). At 6 months, a intergroup difference in PCF was observed in favor of the test (p = 0.042). Moreover, a reduction in SUP from baseline to 6 and 12 months was observed in the test (p = 0.019). Overall, patients in the control group experienced less pain/discomfort compared with the test (p < 0.05), females reporting more pain/discomfort than males (p = 0.005).ConclusionsThis study confirms that conventional non-surgical management of peri-implantitis produces limited clinical improvement. It is shown that an erythritol air-polishing system may not produce added clinical benefits when used adjunctive to conventional non-surgical management. In other words, neither approach effectively resolved peri-implantitis. Moreover, the erythritol air-polishing system produced added pain/discomfort particularly in female patients.Trial registrationThe clinical trial was prospectively registered in ClinicalTrials.gov with registration NCT04152668 (05/11/2019).

A Comparative Evaluation of Soft and Hard Tissue Changes Around Dental Implants Placed With and Without Platelet-Rich Fibrin.

A patient's ability to maintain a healthy bone-implant interface seems to be a major predictor of implant longevity over the long term. The implant surface is protected from the oral environment, the bone, and the implant itself by the peri-implant tissues. Platelet-rich fibrin (PRF) has been shown to help in the regeneration of bone and other connective tissues. Since there has been inadequate information on the role of PRF in maintaining soft tissue integrity and crestal bone changes, the present study aimed to evaluate these challenges clinically and radiographically in human patients who had dental implants placed with PRF. There were a total of 15 patients who were recalled for the analysis, and they were split into two groups. PRF was used to complete the implant procedure in the experimental group, but PRF was not used in the control group. Cone beam computed tomography (CBCT)was used to evaluate the amount of alveolar bone prior to dental implant placement and intra-oral periapical radiograph (IOPAR) for postoperativeassessment. Gingival index, plaque index, probing depths, papilla bleeding index, and crestal bone changes were used to document clinical limits. IOPAR using a similar approach was used to evaluate the crestal bone level alterations. Patients were evaluated clinically and radiographically for changes in the peri-implant soft tissue and crestal bone during implant placement, sixand nine monthspostoperatively. From baseline (p=0.02) to six months (p=0.04) and nine months (p=0.04), both groups showed changes in crestal bone loss and soft tissue although the changes in the test group were smaller. Soft tissue changes showed significant differences for probing depth and papilla index score at baseline and at the end of the six and nine months (p<0.05), whereas no significant difference was noted with bleeding index and plaque index score during the follow-up (p>0.05). To conclude, the provided data demonstrated that the local injection of PRF during implant placement has the potential to favorably stimulatebone formation, and may be used as a therapeutic adjuvant in the clinical setting of implant placement.

A Cone Beam CT Study on the Correlation between Crestal Bone Loss and Periapical Disease

The aim of this study was to determine whether the degree of bone loss around teeth can be linked to the loss of vitality of adjacent teeth and periapical disease, which necessitates root canal treatments. Three hundred and twenty-one full maxilla cone-beam computed tomography scans were examined. The parameters investigated included the degree of crestal bone loss in relation to the cementoenamel junction, the presence/absence of apical periodontitis, and the presence/absence of root canal treatments. Out of the 2001 teeth examined, 696 (34.8%) showed evidence of crestal bone loss. The degree of crestal bone loss was classified as mild, moderate, or severe. A significant association (p < 0.001) was found between the presence of crestal bone loss around a tooth and root canal treatment of that tooth. It was found that it is more likely for teeth with crestal bone loss to be root canal treated compared to teeth with existing root canal treatment and healthy crestal bone levels. Furthermore, teeth with buccal or lingual crestal bone loss were significantly associated with a higher rate of periapical disease than teeth without crestal bone loss (p < 0.001). CBCT identified the severity of bone loss on all surfaces of the teeth, and the most common presentation was bone loss to the mid-root level. Teeth with crestal bone loss were significantly more likely to be associated with a higher rate of periapical disease. Teeth with crestal bone loss were more likely to be root treated than teeth with healthy crestal bone levels.

A Novel Approach of Periodontal Osseous Wall Piezosplitting and Sequential Bone Expansion in Management of Localized Intra-Bony Defects with Wide Angulation-A Randomized Controlled Trial.

Piezoelectric surgical instruments with various mini-sized tips and cutting technology offer a precise and thin cutting line that could allow the wider use of periodontal osseous wall swaging. This randomized controlled trial was designed to investigate the use of a minimally invasive piezo knife to harvest vascularized interseptal bone pedicles in treating intra-bony defects. Sixteen non-smoking patients (mean age 39.6 ± 3.9) with severe chronic periodontitis were randomly assigned into one of two groups (N = 8). The Group 1 (control) patients were treated by bone substitute grafting of the intra-bony defect, whereas the Group 2 patients were treated by intra-bony defect osseous wall swaging (OWS) combined with xenograft filling of the space created by bone tilting. In both groups, the root surfaces were treated with a neutral 24% EDTA gel followed by saline irrigation. Clinical and radiographic measurements were obtained at baseline and 6 months after surgery. The sites treated with osseous wall swaging showed a statistically significant probing-depth reduction and increase in clinical attachment compared with those of the Group 1 patients. The defect base level was significantly reduced for the OWS group compared to that of the Group 1 control. By contrast, the crestal bone level was significantly higher in the OWS group compared to Group 1. The crestal interseptal bone width was significantly higher in Group 2 at 6 months compared to the baseline value and to that of Group 1 (<0.001). The osseous wall swaging effectively improved the clinical hard- and soft-tissue parameters. The use of mini inserts piezo-cutting, sequential bone expanders for osseous wall redirection, and root surface EDTA etching appears to be a reliable approach that could allow the use of OWS at any interproximal dimension.

Comparative Evaluation of the Crestal Bone Level Around Pre- and Post-loaded Immediate Endoosseous Implants Using Cone-Beam Computed Tomography: A Clinico-Radiographic Study.

Introduction Dental implants replacemissing teeth. Dental implants are surgically placed tooth root replacements that secure prosthetic teeth and bridges. Branemark's original dental implant technique included a mesiobuccal flap and a two-stage approach, needing 6-8 months of recovery following extraction, sterile conditions, machined titanium implants, 3-6 months without stress for osseointegration, and a detachable temporary prosthesis. The restoration would usually be ready a year following the implant surgery. Implant treatment seeks the best function, aesthetics, and complication risk. Implant therapy with low patient morbidity and fast extraction-to-restoration times is asecondary target. Instantaneous implant insertion has made implant dentistry more convenient for patients and clinicians. This study measures bone height before, after, and one month after implant placement using cone-beam computed tomography (CBCT). Materialsand Methods Participants were selected from oral evaluation candidates. This investigation included 11 people missing front maxillary or mandibular teeth or root components. Diagnostic castings determined the interarch connection before surgery. Alginate maxillary and mandibular arch imprints were cast in Type III dental stone for diagnosis. CBCT scans were taken pre-operatively, post-implant, and post-prosthesis. After the tooth was removed, the empty socket was cleaned up with curettes. An intraoral periapical radiographand manual probing were done to determine the implant's size. The implant was removed for examination after three months, and healing abutments and gingival formers were placed. Finally, fins were placed. The CBCT images also captured the bone height around the implants. The soft tissue parameters were recorded and evaluated at baseline and one-month following prosthetic loading as plaque index (PI). Radiographic evaluation was done at baseline and one-month following functional loading using CBCT. After one month following functional loading, crestal bone levels were measured again with the help of CBCT using Image J software (National Institutes of Health, Bethesda,Maryland, US). Results The sample population had an average age of 42.81 years, with a standard deviation of 13.44 years. Using a paired t-test, we found that the mean PI dropped significantly from pre-loading levels to one-month post-loading levels, with a p-value of less than 0.001. The mean crestal bone level (mesial) evaluated by CBCT at baseline and one-month post-loading was 2.52 ± 1.97 mm and 1.17 ± 1.31 mm, respectively. The mean difference between mean crestal bone loss (distal) at baseline and one-month post-loading was 0.94 ± 1.89 mm, which was not statistically significant. The mean difference between mean crestal bone loss (buccal) at baseline and one-month post-loading was 1.82 ± 1.60 mm, which was statistically significant. The mean difference between mean crestal bone loss (lingual) at baseline and one-month post-loading was 1.91 ± 1.53 which was statistically significant. Conclusion CBCT provides all the diagnostic data needed for implant placement; hence, it is recommended.