Core-shell Microgels Research Articles

Drying of Soft Colloidal Films.

Thin films made of deformable micro- and nano-units, such as biological membranes, polymer interfaces, and particle-laden liquid surfaces, exhibit a complex behavior during drying, with consequences for various applications like wound healing, coating technologies, and additive manufacturing. Studying the drying dynamics and structural changes of soft colloidal films thus holds the potential to yield valuable insights to achieve improvements for applications. In this study, interfacial monolayers of core-shell (CS) microgels with varying degrees of softness are employed as model systems and to investigate their drying behavior on differently modified solid substrates (hydrophobic vs hydrophilic). By leveraging video microscopy, particle tracking, and thin film interference, this study shed light on the interplay between microgel adhesion to solid surfaces and the immersion capillary forces that arise in the thin liquid film. It is discovered that a dried replica of the interfacial microstructure can be more accurately achieved on a hydrophobic substrate relative to a hydrophilic one, particularly when employing softer colloids as opposed to harder counterparts. These observations are qualitatively supported by experiments with a thin film pressure balance which allows mimicking and controlling the drying process and by computer simulations with coarse-grained models.

Soft and Deformable Thermoresponsive Hollow Rod-Shaped Microgels.

Depending on their aspect ratio, rod-shaped particles exhibit a much richer 2D and 3D phase behavior than their spherical counterparts, with additional nematic and smectic phases accompanied by defined orientational ordering. While the phase diagram of colloidal hard rods is extensively explored, little is known about the influence of softness in such systems, partly due to the absence of appropriate model systems. Additionally, investigating higher volume fractions for long rods is usually complicated because non-equilibrium dynamical arrest is likely to precede the formation of more defined states. This has motivated us to develop micrometric rod-like microgels with limited sedimentation that can respond to temperature and reversibly reorganize into defined phases via annealing and seeding procedures. A detailed procedure is presented for synthesizing rod-shaped hollow poly(N-isopropylacrylamide) microgels using micrometric silica rods as sacrificial templates. Their morphological characterization is conducted through a combination of microscopy and light scattering techniques, evidencing the unconstrained swelling of rod-shaped hollow microgels compared to core-shell microgel rods. Different aspects of their assembly in dispersion and at interfaces are further tested to illustrate the opportunities and challenges offered by such systems that combine softness, anisotropy, andthermoresponsivity.

In Situ Triggered Self-Contraction Bioactive Microgel Assembly Accelerates Diabetic Skin Wound Healing by Activating Mechanotransduction and Biochemical Pathway.

Chronic nonhealing skin wounds, characterized by reduced tissue contractility and inhibited wound cell survival under hyperglycemia and hypoxia, present a significant challenge in diabetic care. Here, an advanced self-contraction bioactive core-shell microgel assembly with robust tissue-adhesion (SMART-EXO) is introduced to expedite diabetic wound healing. The SMART-EXO dressing exhibits strong, reversible adhesion to damaged tissue due to abundant hydrogen and dynamic coordination bonds. Additionally, the core-shell microgel components and dynamic coordination bonds provide moderate rigidity, customizable self-contraction, and an interlinked porous architecture. The triggered in situ self-contraction of the SMART-EXO dressing enables active, tunable wound contraction, activating mechanotransduction in the skin and promoting the optimal fibroblast-to-myofibroblast conversion, collagen synthesis, and angiogenesis. Concurrently, the triggered contraction of SMART-EXO facilitates efficient loading and on-demand release of bioactive exosomes, contributing to re-epithelialization and wound microenvironment regulation in diabetic mice. RNA-seq results reveal the activation of critical signaling pathways associated with mechanosensing and exosome regulation, highlighting the combined biomechanical and biochemical mechanisms. These findings underscore SMART-EXO as a versatile, adaptable solution to the complex challenges of diabetic wound care.

Non-close-packed plasmonic Bravais lattices through a fluid interface-assisted colloidal assembly and transfer process

AbstractThe assembly of colloids at fluid interfaces followed by their transfer to solid substrates represents a robust bottom-up strategy for creating colloidal monolayers over large, macroscopic areas. In this study, we showcase how subtle adjustments in the transfer process, such as varying the contact angle of the substrate and controlling deposition speed and direction, enable the realization of all five two-dimensional Bravais lattices. Leveraging plasmonic core–shell microgels as the building blocks, we successfully engineered non-close-packed plasmonic lattices exhibiting hexagonal, square, rectangular, centered rectangular, and oblique symmetries. Beyond characterizing the monolayer structures and their long-range order, we employed extinction spectroscopy alongside finite difference time domain simulations to comprehensively investigate and interpret the plasmonic response of these monolayers. Additionally, we probed the influence of the refractive index environment on the plasmonic properties by two methods: first, by plasma treatment to remove the microgel shells, and second, by overcoating the resulting gold nanoparticle lattices with a homogeneous refractive index polymer film. Graphical Abstract

Volume Phase Transition of Thermoresponsive Microgels Scrutinized by Dynamic Light Scattering and Turbidity: Correlations Depend on Microgel Homogeneity.

Thermoresponsive microgels experience a volume phase transition triggered by temperature changes, a phenomenon often analyzed using dynamic light scattering to observe overall size alterations via the diffusion coefficient. However, local structural changes are typically assessed using more intricate and expensive techniques like small-angle neutron or X-ray scattering. In our research, we investigate the volume phase transition of poly-N-isopropylacrylamide (PNIPAM)-based microgels by employing a combination of temperature-dependent dynamic light scattering and simpler, faster, and more efficient attenuation measurements. We utilize attenuation at a fixed wavelength as a direct measure of dispersion turbidity, linking the absolute changes in hydrodynamic radius to the absolute changes in turbidity. This approach allows us to compare "classical" PNIPAM microgels from precipitation polymerization, charged copolymer microgels from precipitation copolymerization, and core-shell microgels from seeded precipitation polymerization. Our study includes a systematic analysis and comparison of 30 different microgels. By directly comparing data from dynamic light scattering and attenuation spectroscopy, we gain insights into structural heterogeneity and deviations from the established fuzzy sphere morphology. Furthermore, we demonstrate how turbidity data can be converted to swelling curves.

Silica@poly(chitosan-N-isopropylacrylamide-methacrylic acid) microgels: Extraction of palladium (II) ions and in situ formation of palladium nanoparticles for pollutant reduction

Most of the transition metal ions and organic dyes are toxic in nature. Therefore, their removal from water is imperative for human health. For this purpose, various types of systems have been developed to tackle either transition metal ions or organic dyes individually. A core-shell microgel system is introduced which is capable of effectively removing both types (toxic organic dyes and transition metal ions) of pollutants. A long-rod-shaped silica@poly(chitosan-N-isopropylacrylamide-methacrylic acid) S@P(CS-NIPAM-MAA) S@P(CNM) core-shell microgel system was developed by free radical precipitation polymerization method (FRPPM). S@P(CNM) was utilized as an adsorbent for extracting palladium (II) (Pd (II)) ions from water under different concentrations of S@P(CNM), several agitation times, palladium (II) ion content, and pH levels. The adsorption data of Pd (II) ions on S@P(CNM) was evaluated by various adsorption isotherms. The kinetic study was investigated by employing pseudo-2nd order (Ps2O), Elovich model (ElM), intra-particle diffusion (IPDM), and pseudo-1st order (Ps1O). Additionally, palladium nanoparticles (Pd NPs) were generated via in-situ reduction of adsorbed Pd (II) ions within the P(CNM) shell region of S@P(CNM). The resulting Pd NPs loaded S@P(CNM) exhibited the capability to reduce organic pollutants like methyl orange (MeO), 4-nitrophenol (4NiP), methylene blue (MeB), and Rhodamine B (RhB) from aqueous medium. 0.766 min−1, 0.433 min−1, 0.682 min−1, and 1.140 min−1 were the values of pseudo 1st order rate constant (kobs) for catalytic reduction of MeB, 4NiP, MeO, and RhB respectively. The S@Pd-P(CNM) system exhibits significant catalytic potential for various organic transformations.

Thermosensitive ZnO-PMMA/PEG microgels: A smart sunscreen with adapting SPF to ambient temperature fluctuations

Increasing awareness of the importance of ultraviolet protection has led to the development and utilization of sunscreen products. The sun protection factor (SPF) value of traditional sunscreens is fixed and cannot be flexibly adapted to changing environmental requirements. Herein, we fabricate a series of thermosensitive ZnO-poly (methyl methacrylate)/nonlinear poly(ethylene glycol) (PMMA/PEG) core-shell microgel with different monomer ratios. The PMMA core particle is designed to immobilize ZnO nanoparticles for achieving high loading capacity, and the hydrophilic nonlinear PEG gel shell possesses good biocompatibility and provides adjustable SPF value in response to different environmental conditions. The prepared microgels are monodisperse spherical with a well-defined core-shell morphology. The shell thickness of the microgels can be easily controlled by changing the feeding ratios of shell precursors. The optimized ZnO-PMMA/PEG microgels display significant sun protection properties at a concentration of 10 wt% (SPF 45 ± 5.9, 20 °C) and enhanced UV resistance performance as the temperature increases (SPF 53.1 ± 1.1, 37 °C). Both cell and mouse experiments confirmed the limited skin penetration potential of the microgels and their good compatibility with biological systems. This developed ZnO-PMMA/PEG microgels exhibit promising application potential in intelligent sunscreen technology.

Multiresponsive Core-Shell Microgels Functionalized by Nitrilotriacetic Acid.

Stimuli-responsive microgels with ionizable functional groups offer versatile applications, e.g., by the uptake of oppositely charged metal ions or guest molecules such as drugs, dyes, or proteins. Furthermore, the incorporation of carboxylic groups enhances mucoadhesive properties, crucial for various drug delivery applications. In this work, we successfully synthesized poly{N-vinylcaprolactam-2,2'-[(5-acrylamido-1-carboxypentyl)azanediyl]diacetic acid} [p(VCL/NTAaa)] microgels containing varying amounts of nitrilotriacetic acid (NTA) using precipitation polymerization. We performed fundamental characterization by infrared (IR) spectroscopy and dynamic and electrophoretic light scattering. Despite their potential multiresponsiveness, prior studies on NTA-functionalized microgels lack in-depth analysis of their stimuli-responsive behavior. This work addresses this gap by assessing the microgel responsiveness to temperature, ionic strength, and pH. Morphological investigations were performed via NMR relaxometry, nanoscale imaging (AFM and SEM), and reaction calorimetry. Finally, we explored the potential application of the microgels by conducting cytocompatibility experiments and demonstrating the immobilization of the model protein cytochromec in the microgels.

Conceptualizing flexible papers using cellulose model surfaces and polymer particles.

Cellulose, as a naturally abundant and biocompatible material, is still gaining interest due to its high potential for functionalization. This makes cellulose a promising candidate for replacing plastics. Understanding how cellulose interacts with various additives is crucial for creating composite materials with diverse properties, as it is the case for plastics. In addition, the mechanical properties of the composite materials are assumed to be related to the mobility of the additives against the cellulose. Using a well-defined cellulose model surface (CMS), we aim to understand the adsorption and desorption of two polymeric particles (core-shell particles and microgels) to/from the cellulose surface. The nanomechanics of particles and CMS are quantified by indentation measurements with an atomic force microscope (AFM). AFM topography measurements quantified particle adsorption and desorption on the CMS, while peak force AFM measurements determined the force needed to move individual particles. Both particles and the CMS exhibited pH-dependent charge behavior, allowing a tunable interaction between them. Particle adsorption was irreversible and driven by electrostatic forces. In contrast, desorption and particle mobility forces are dominated by structural morphology. In addition, we found that an annealing procedure consisting of swelling/drying cycles significantly increased the adhesion strength of both particles. Using the data, we achieve a deeper understanding of the interaction of cellulose with polymeric particles, with the potential to advance the development of functional materials and contribute to various fields, including smart packaging, sensors, and biomedical applications.

Dual stimuli-responsive upconversion nanoparticle-poly-N-isopropylacrylamide/DNA core-shell microgels.

Stimuli-responsive upconversion nanoparticle (UCNP)-poly-N-isopropylacrylamide (pNIPAM)/DNA core-shell microgels with tunable sizes and programmable functions have been prepared. Thanks to the near-infrared (NIR)-responsive UCNP cores and thermosensitive polymeric shells, functional DNA-incorporated microgels with high DNA activity and loading efficiency are obtained, and the activity of the loaded DNA structures can be smartly regulated by NIR illumination and temperature simultaneously.

A polyampholyte core-shell microgel as an environmentally sensitive drug carrier

In this study, we investigate a polyampholyte degradable core-shell (CS) microgel, with an anionic pH-sensitive core and a cationic pH- and temperature-sensitive shell, as a model system for drug delivery. The core was based on crosslinked poly(acrylic acid) and was synthesized through distillation precipitation polymerization. Then, the shell, based on cross-linked poly(poly(ethylene glycol) methyl ether methacrylate - N-(3-aminopropyl)methacrylamide), were built over the core via the seed polymerization. N,N′-bis(acryloyl)cystamine was used as the linker for cross-linking both core and shell to give the core-shell particles the ability to degrade in the presence of reducing agent. The swelling characteristics of the core-shell microgels were studied using dynamic light scattering (DLS). The core-shell particles exhibited sensitivity to pH due to the presence of carboxylic and amine groups in the core and shell, respectively. The degradation of the core-shell particles was examined using electron microscopy and DLS. In the presence of glutathione, which acts as a reducing agent for the -S-S- bridges, commonly found in cancer cells, the particles underwent complete degradation. Our findings also demonstrate that the presence of the positively charged shell still enables efficient uptake of a drug in the form of a cation (doxorubicin DOX) into the anionic core and the drug can be released through the cationic shell. The release of DOX from the carrier was studied under different pH conditions to mimic the environment found in cancer cells. The results showed that at pH 7.4, the carrier exhibited the lowest release of DOX. However, under conditions mimicking the acidic and reducing environment typically for tumor microenvironment (pH 5.0 and cGSH = 40 mM), the CS particles demonstrated the highest cumulative and sustained release of DOX. The results showed that the DOX-loaded particles exhibited increased cytotoxicity against MCF-7 cells, indicating enhanced anti-cancer activity. At the same time, these particles demonstrated reduced toxicity towards healthy MCF-10A cells, which suggests improved selectivity and reduced side effects. It is worth noting that the gel nanoparticles alone did not inhibit cell growth. Overall, these findings suggest that the DOX-loaded core-shell particles hold promise as a targeted drug delivery system, capable of preferentially releasing the drug in the acidic and reducing tumor microenvironment while minimizing toxicity towards healthy cells.

A novel bioartificial pancreas fabricated via islets microencapsulation in anti-adhesive core-shell microgels and macroencapsulation in a hydrogel scaffold prevascularized in vivo.

Islets transplantation is a promising treatment for type 1 diabetes mellitus. However, severe host immune rejection and poor oxygen/nutrients supply due to the lack of surrounding capillary network often lead to transplantation failure. Herein, a novel bioartificial pancreas is constructed via islets microencapsulation in core-shell microgels and macroencapsulation in a hydrogel scaffold prevascularized in vivo. Specifically, a hydrogel scaffold containing methacrylated gelatin (GelMA), methacrylated heparin (HepMA) and vascular endothelial growth factor (VEGF) is fabricated, which can delivery VEGF in a sustained style and thus induce subcutaneous angiogenesis. In addition, islets-laden core-shell microgels using methacrylated hyaluronic acid (HAMA) as microgel core and poly(ethylene glycol) diacrylate (PEGDA)/carboxybetaine methacrylate (CBMA) as shell layer are prepared, which provide a favorable microenvironment for islets and simultaneously the inhibition of host immune rejection via anti-adhesion of proteins and immunocytes. As a result of the synergistic effect between anti-adhesive core-shell microgels and prevascularized hydrogel scaffold, the bioartificial pancreas can reverse the blood glucose levels of diabetic mice from hyperglycemia to normoglycemia for at least 90 days. We believe this bioartificial pancreas and relevant fabrication method provide a new strategy to treat type 1 diabetes, and also has broad potential applications in other cell therapies.

A Simple and Fast Compression‐Based Method to Fabricate Responsive Gold‐pNIPAM Hybrid Materials: From Thin Films to Anisotropic Microgels

AbstractIn recent years, hydrogel‐based soft materials with hybrid properties have found widespread use in various technological fields, including tissue engineering, soft actuators, and flexible electronics. The proper implementation of these smart multifunctional materials into real‐world applications requires the development of simple, cost‐effective, and large‐scale fabrication methods. Herein, a simple compression‐ and colloid‐based method is presented to fabricate responsive Au‐poly(N‐isopropylacrylamide) (pNIPAM) hybrid films using photopolymerizable resin containing Au‐pNIPAM core–shell microgels as building blocks. Uniform Au‐pNIPAM hybrid films of 25 × 25 mm with adjustable thickness in the micron‐size range (2.3–1.2 µm) w ere successfully fabricated on glass substrates and flexible commercial acetate sheets. The resulting flexible Au‐pNIPAM films exhibit robust optical and mechanical properties, even after repeated edge‐to‐edge bending cycle tests. Additionally, using patterned light to polymerize the Au‐pNIPAM films allows synthesizing of anisotropic Au‐pNIPAM microgels with high width‐to‐height aspect ratios, such as square, circular, and rectangular microgels, adding a new dimension to the proposed fabrication method.

Wrapping anisotropic microgel particles in lipid membranes: Effects of particle shape and membrane rigidity

Cellular engulfment and uptake of macromolecular assemblies or nanoparticles via endocytosis can be associated to both healthy and disease-related biological processes as well as delivery of drug nanoparticles and potential nanotoxicity of pollutants. Depending on the physical and chemical properties of the system, the adsorbed particles may remain at the membrane surface, become wrapped by the membrane, or translocate across the membrane through an endocytosis-like process. In this paper, we address the question of how the wrapping of colloidal particles by lipid membranes can be controlled by the shape of the particles, the particle-membrane adhesion energy, the membrane phase behavior, and the membrane-bending rigidity. We use a model system composed of soft core-shell microgel particles with spherical and ellipsoidal shapes, together with phospholipid membranes with varying composition. Confocal microscopy data clearly demonstrate how tuning of these basic properties of particles and membranes can be used to direct wrapping and membrane deformation and the organization of the particles at the membrane. The deep-wrapped states are more favorable for ellipsoidal than for spherical microgel particles of similar volume. Theoretical calculations for fixed adhesion strength predict the opposite behavior-wrapping becomes more difficult with increasing aspect ratio. The comparison with the experiments implies that the microgel adhesion strength must increase with increasing particle stretching. Considering the versatility offered by microgels systems to be synthesized with different shapes, functionalizations, and mechanical properties, the present findings further inspire future studies involving nanoparticle-membrane interactions relevant for the design of novel biomaterials and therapeutic applications.

Core-shell chitosan/Porphyridium-exopolysaccharide microgels: Synthesis, properties, and biological evaluation

Advanced materials used in the biomedicine field comprises a diverse group of organic molecules, including polymers, polysaccharides, and proteins. A significant trend in this area is the design of new micro/nano gels whose small size, physical stability, biocompatibility, and bioactivity could lead to new applications. Herein a new synthesis route is described to obtain core-shell microgels based on chitosan and Porphyridium exopolysaccharides (EPS) crosslinked with sodium tripolyphosphate (TPP). First, the synthesis of EPS-chitosan gels through ionic interactions was explored, leading to the formation of unstable gels. Alternatively, the use of TTP as crosslinker agent led to stable core-shell structures. The influence of reaction temperature, sonication time, and exopolysaccharide concentration, pH and TPP concentration were determined as a function of particle size and polydispersity index (PDI). The obtained EPS-chitosan gels were characterized by TEM, TGA, and FTIR; followed by the assessment of protein load capacity, stability upon freezing, cytotoxicity, and mucoadhesivity. Experimentation revealed that the core-shell particles size ranges 100–300 nm, have a 52 % loading capacity for BSA and a < 90 % mucoadhesivity, and no toxic effects in mammalian cell cultures. The potential application of the obtained microgels in the biomedical field is discussed.

Synthesis and characterization of PNM@IAM core-shell microgels through inverse emulsion polymerization and its application for heavy metal ions capture

In this study, thermo and pH-sensitive multifunctional poly (N-isopropylacrylamide-co- N,N’-methylenebisacrylamide, Poly(NIPAAm-co-MBA) - (N-4-amino-2-methylene-4-oxobutanoic acid, IAM) named as (PNM@IAM) core-shell microgels are synthesized by inverse microemulsion polymerization technique using two monomers, N-isopropylacrylamide (NIPAAm) and N-4-amino-2-methylene-4-oxobutanoic acid (IAM). The formation of the microgels are confirmed by 1H nuclear magnetic resonance (1H NMR) and attenuated total reflection fourier transform infrared (ATR-FTIR) spectra. The light transmittance study shows that the microgels prepared at different concentrations and pHs exhibit different physical properties. The phase transition temperature is increased with the addition of IAM. Dynamic light scattering (DLS) analysis reveals that the swelling of the microgels at basic environment is due to the deprotonation of the weak acid groups in IAM. The metal ion chelating test shows that the core-shell PNM@IAM could effectively absorb metal ions in highly basic environment. The absorption and release of heavy metal ions from aqueous solution could be controlled by adjusting the pH of the reaction environment.

Bactericidal and biocatalytic temperature responsive microgel based self-cleaning membranes for water purification

The present study focuses on creating an antimicrobial and biocatalytic smart gating membrane by synthesizing unique core–shell microgels. The core–shell microgels are synthesized by grafting short chains of poly(ethylenimine) (PEI) onto a poly((N-isopropyl acrylamide)–co-glycidyl methacrylate)) (P(NIPAm-co-GMA)) core. Subsequently, the produced microgels are utilized as a substrate for synthesizing and stabilizing silver nanoparticles (Ag NPs) through an in-situ approach. These Ag NPs immobilized microgels are then suction filtered over a polyethylene terephthalate (PET) track-etched support to create cross-linked composite microgel membranes (CMMs). After structural and permeation characterization of the prepared CMMs, the laccase enzyme is then covalently grafted to the surface of the membrane and tested for its effectiveness in degrading Reactive red-120 dye. The laccase immobilized biocatalytic CMMs show effective degradation of the Reactive red-120 by 71%, 48%, and 34% at pH 3, 4, and 5, respectively. Furthermore, the immobilized laccase enzyme showed better activity and stability in terms of thermal, pH, and storage compared to the free laccase, leading to increased reusability. The unique combination of Ag NPs and laccase on a thermoresponsive microgel support resulted in a responsive self-cleaning membrane with excellent antimicrobial and dye degradation capabilities for environmentally friendly separation technology.

Bioprinting microporous functional living materials from protein-based core-shell microgels

Living materials bring together material science and biology to allow the engineering and augmenting of living systems with novel functionalities. Bioprinting promises accurate control over the formation of such complex materials through programmable deposition of cells in soft materials, but current approaches had limited success in fine-tuning cell microenvironments while generating robust macroscopic morphologies. Here, we address this challenge through the use of core-shell microgel ink to decouple cell microenvironments from the structural shell for further processing. Cells are microfluidically immobilized in the viscous core that can promote the formation of both microbial populations and mammalian cellular spheroids, followed by interparticle annealing to give covalently stabilized functional scaffolds with controlled microporosity. The results show that the core-shell strategy mitigates cell leakage while affording a favorable environment for cell culture. Furthermore, we demonstrate that different microbial consortia can be printed into scaffolds for a range of applications. By compartmentalizing microbial consortia in separate microgels, the collective bioprocessing capability of the scaffold is significantly enhanced, shedding light on strategies to augment living materials with bioprocessing capabilities.

Extraction of iron (III) ions by core-shell microgel for in situ formation of iron nanoparticles to reduce harmful pollutants from water

Since the most transition metal ions and organic dyes are hazardous, it is crucial to remove them from water. For this purpose, various systems are reported for removal of only transition metal ions or organic dyes. I have introduced a new system which is suitable for removal of both metal ions and organic dyes. The free radical precipitation polymerization method was used to create the spherical system of silica surrounded by poly(N-vinylcaprolactam-acrylic acid) S@P(NVCP-AA) core shell microgels and then characterized by using FTIR, DLS, XRD, and STEM. The S@P(NVCP-AA) microgel system was applied as adsorbent to extract iron (III) ions from water under various concentrations of S@P(NVCP-AA), iron (III) ions content, pH, and agitation time. The adsorption process of iron (III) ions on S@P(NVCP-AA) microgels was investigated by different adsorption isotherms. The kinetics of adsorption of iron (III) ions on S@P(NVCP-AA) microgel system was also examined by intra-particle diffusion model (InPDM), pseudo-1st order (P1O), pseudo-2nd order (P2O) and Elovich model (EM). Iron nanoparticles were formed by in-situ reduction of iron (III) ions that had been adsorbed in the P(NVCP-AA) shell region of the S@P(NVCP-AA) microgel. The organic pollutants and toxic transition metal ions like 4-nitrophenol (4NiP), methyl red (MeR), methylene blue (MeB) and chromium (VI) ions (CMI) were reduced from an aqueous medium by using the iron nanoparticles loaded in S@P(NVCP-AA) microgels. The pseudo 1st order rate constant values for the catalytic reduction of 4NiP, MeR, MeB and CMI were found to be 0.778 min−1, 0.928 min−1, 0.943 min−1 and 0.142 min−1 respectively. The resulting S@Fe-P(NVCP-AA) system can act as an efficient catalyst for a wide range of additional organic transformations.

Fluid-solid transitions in photonic crystals of soft, thermoresponsive microgels.

Microgels are often discussed as well-suited model system for soft colloids. In contrast to rigid spheres, the microgel volume and, coupled to this, the volume fraction in dispersion can be manipulated by external stimuli. This behavior is particularly interesting at high packings where phase transitions can be induced by external triggers such as temperature in the case of thermoresponsive microgels. A challenge, however, is the determination of the real volume occupied by these deformable, soft objects and consequently, to determine the boundaries of the phase transitions. Here we propose core-shell microgels with a rigid silica core and a crosslinked, thermoresponsive poly-N-isopropylacrylamide (PNIPAM) shell with a carefully chosen shell-to-core size ratio as ideal model colloids to study fluid-solid transitions that are inducible by millikelvin changes in temperature. Specifically, we identify the temperature ranges where crystallization and melting occur using absorbance spectroscopy in a range of concentrations. Slow annealing from the fluid to the crystalline state leads to photonic crystals with Bragg peaks in the visible wavelength range and very narrow linewidths. Small-angle X-ray scattering is then used to confirm the structure of the fluid phase as well as the long-range order, crystal structure and microgel volume fraction in the solid phase. Thanks to the scattering contrasts and volume ratio of the cores with respect to the shells, the scattering data do allow for form factor analysis revealing osmotic deswelling at volume fractions approaching and also exceeding the hard sphere packing limit.