Copper Powder Research Articles

Constructing artificial photosynthetic system based on graphdiyne double heterojunction to enhance REDOX capacity and hydrogen evolution efficiency

Although traditional type II heterojunction designs for artificial photosynthesis show promise for photocatalytic hydrogen production, their redox capacity is somewhat limited due to the spatial separation of hydrogen evolution and oxidation reactions at less favorable sites. To overcome this limitation, ohmic junctions based on type II heterojunctions have been designed to enhance hydrogen evolution by transferring electrons to the metal component. In this study, a copper powder graphdiyne (Cu-GDY) composite catalyst with ohmic angle contact was synthesized by coupling copper foil with hexa-hexylbenzene. Incorporating Cu-GDY into CoGdO3 results in an interleaved band structure forming a type II heterojunction at the contact interface. This configuration overcomes the issue of the unfavorable conduction band position of CoGdO3, thereby promoting charge transfer. The internal electric field created by the Fermi level difference between Cu-GDY and CoGdO3, increase in REDOX capacity is the main reason for the increase of carrier separation rate. In addition, the plasmonic properties of copper expand the active reaction sites and promote the hydrogen evolution reaction. The composite catalyst exhibits b a hydrogen production rate that is 10.5 times higher than that of the individual catalysts. This work demonstrates that the formation of two distinct contact interfaces between Cu-GDY and CoGdO3 significantly improves the electron transfer and hydrogen evolution performance.

Flow boiling heat transfer in multi-stage enhanced open microchannels with micro/nano structures

In the realm of flow boiling research, open microchannels heat sink is garnering more attention due to its potential in enhancing heat transfer and mitigating flow instability. Nevertheless, growing heat dissipation needs necessitate further enhancement of the heat removing capability of flow boiling within open microchannels. In this paper, experimental research on flow boiling in open microchannels utilized a new environmentally friendly refrigerant SF-33 and presented a novel heat transfer enhancement strategy, specifically, a multi-region enhancement strategy for diverse flow pattern stages. A copper heat sink with 25 open microchannels was fabricated, and a layer of copper powder particles was sintered on the channel bottom to create a microporous structured surface in about 1/3 of the inlet region. Several layers of copper wire mesh with micropores were sintered in about 1/3 of the outlet region, and the nanostructures were grown on the wire mesh by chemical treatment, resulting in a micro-nanocomposite structure. The final product formed the multi-stage enhanced open microchannels (MSEOM). The heat transfer performance and pressure drop of SF-33 saturated flow boiling in MSEOM under different operating conditions were determined, and the transitions of flow patterns were visualized to analyze the mechanism of two-phase heat transfer. The study demonstrated that despite SF-33 having a low latent heat of vaporization, its flow boiling heat transfer coefficient in MSEOM was high. This was attributed to the enhanced effect of multi-region surface modifications on heat transfer. Additionally, a vapor plug breakup-dispersed bubble flow pattern was observed for the first time, which resulted from the combined influence of the low surface tension property of SF-33 and the boosted nucleate boiling triggered by the micro-nanostructures in the outlet region.

Three-Dimensional Numerical Simulation of High-Speed Shear Crushing of High-Density Fluid

Plasma atomization is a technology that can produce high sphericity, small particle diameters, and high-purity copper powder, which is of great significance for the development of metal additive manufacturing. At present, although plasma atomization can realize the industrial preparation of spherical copper powder, there are still some problems, such as unclear understanding of the atomization process and a lack of theoretical support for powder quality control. This leads to the inability to predict the average particle diameter of powder in advance based on the actual atomization conditions and to optimize the process parameters, which seriously affects the further development of the plasma atomization process. We mainly studied the non-stationary simulation of a DC argon plasma torch. The purpose of this paper was to study the specific influence law of the average particle diameter of the powder in the process of plasma atomization by means of numerical simulation and experimental observation. The aim was to establish the mapping relationship between the atomization condition and the average particle diameter of the powder and realize the controllable preparation of the plasma atomized powder. At the same time, we used industrial-grade plasma atomization equipment to carry out pulverizing experiments to verify the plasma atomization theory and the powder average particle diameter control scheme proposed in this paper, thus proving the reliability of this study.

Spark Plasma Sintering of a Cu-Cu2O powder obtained by partial oxidation of electrolytic copper

Studies of consolidation of pre-oxidized powders are interesting from the viewpoint of gaining an understanding of the features of sintering of metallic core-oxide shell particles and the formation of oxide-reinforced composites. If spark plasma sintering (SPS) is selected as a consolidation method, the possibility of the oxide interacting with graphite tooling/foil should be taken into account in the development of metal-oxide composites. In the present work, materials fabricated by SPS of a partially oxidized copper powder containing Cu2O were studied. The pre-oxidized powder obtained by annealing an electrolytic copper powder in air was subjected to SPS in contact with a graphite foil. Pressureless SPS at 700 °C resulted in the formation of a porous structure, in which the morphology of the ligaments was similar to that of the particles of the oxidized powder. The grain structure of the oxide layers could be well distinguished. After SPS at 700 °C and 40 MPa; the Cu2O phase was preserved even in the subsurface layer of the compact. The oxide reduction to metal was observed after SPS at 900 °C and occurred only in the vicinity of the graphite foil. The Cu-Cu2O composites sintered under a pressure of 40 MPa at 700 °C and 900 °C had a porosity of 5% and a Vickers hardness of 140±5 HV0.3 and 120±5 HV0.3, respectively. A reduction in hardness of the composites can be explained by grain growth in the material sintered at a higher temperature.

Study of the Sintering Process Behavior on Some Structural and Physical Properties of (Ni-47Ti-3Cu) Alloy Prepared by Powder Metallurgy

This research aims to prepare the alloy (Ni-47Ti-3Cu) using powder metallurgy techniques and study the sintering behavior of this alloy at different temperatures. Powders of nickel, titanium, and copper, were mixed to ensure homogeneity, then compacted under a pressure of (5ton) for (2 min) to obtain cohesive samples. The sintering process was carried out at temperatures of (1050, 950, 850, 750, 650) °C for 1 hour. The structural properties were studied using X-ray diffraction (XRD), and the physical properties (apparent density, bulk density, porosity, and water absorption) were examined using Archimedes' principle-based tests. The XRD results indicated the emergence of a new phase with a different crystalline structure from the elements used in the preparation of the models, identified as (TiCuNi2) with a rhombohedral crystal system, while the constituent elements of the alloy exhibited face-centered cubic (F.C.C) structures for nickel and copper and a hexagonal close-packed (H.C.P) structure for titanium. The physical examination results showed that both apparent and bulk densities increased with increasing sintering temperature, while porosity and water absorption decreased with increasing sintering temperature.

A comparative study of flow boiling performance in smooth and multi-stage enhanced open microchannels

Flow boiling in open microchannels is currently one of the research focuses in the field of phase-change heat transfer. The present paper described a comparative and experimental research on flow boiling heat transfer of SF-33, an environmentally friendly working fluid, in smooth surfaces open microchannels (SOM) and multi-stage enhanced open microchannels (MSEOM). The study investigated the flow boiling performance of SF-33 in two open microchannels with different mass fluxes, heat fluxes and inlet subcooling. The different boiling flow patterns in two open microchannels were analyzed with high-speed visualization. The results indicated that under different inlet cooling conditions, the MSEOM improved the flow boiling heat transfer performance significantly and improved the wall temperature uniformity. The visualization images indicated that the flow pattern transition was different due to the different surface structures of two open microchannels. The SOM experienced plug-stratified flow at high heat flux, while MSEOM transformed into churn flow due to its sintered copper powder and wire mesh micro-nanocomposite structures. The multi-stage enhanced structures exhibited excellent hydrophilicity and wicking capability, leading to a less pressure drop in the MSEOM compared with that in SOM. The pressure drops for both open microchannels decreased as inlet subcooling increased.

EXTREMELY DEFORMED SINTERED COPPER NANOCOMPOSITES STRUCTURE AND PROPERTIES EVOLUTION

The purpose of the work is to determine the structure and mechanical properties of sintered copper (including those containing carbon nanotubes) after intensive plastic deformation by torsion. Methodology: The research objects are samples of copper powder PMS-1 (GOST 4960-75), copper powder with a 45 microns’ fraction, copper powder PMS-1 with the carbon nanotubes addition 1 % by weight, manufactured by double pressing − sintering, with a 700 MPa final pressure, temperature of 950 °C, and subjected to intensive plastic deformation by torsion on a Bridgman anvil. The structure is investigated using a Tescan Micra 3 LMU scanning electron microscope. Micromechanical tests were carried out using the “Micron – Gamma” device. Originality. At first, the microstructure and mechanical properties of sintered copper and nanomaterial “copper − carbon nanotubes” after intensive plastic deformation by torsion were investigated. It has been established that intensive plastic deformation by torsion significantly affects the sintered copper samples structure and mechanical properties. The sintered copper grain shape changes from approximately spherical to elongated in the deformation direction, and the grain size decreases by 5−7 times. In the case of “copper + 1 % CNT” nanomaterial intensive deformation, the grain refinement effect is significantly less pronounced. A significant increase in the mechanical properties of sintered copper during intensive plastic deformation has been established. The highest indicators were obtained for the “copper + 1 % CNT” nanomaterial. Practical value. The results of the work can be used in the manufacture of copper products for electrical and thermal purposes with increased wear resistance.

Effect of mixing-ratio and current on Mo-Cu-WC-Si coating via EDC

The present study investigates the influence of the mixing ratio of copper (Cu) and molybdenum (Mo) powders in Mo-Cu-WC-Si composite powder metallurgy (P/M) briquettes on the performance of coatings produced on Al-2014 alloy using electrical discharge coating. Three mixing ratios of Cu and Mo are selected during briquette preparation, by varying Cu in 5 wt.% decrements and Mo in 5 wt.% increments: 50Cu:30Mo, 45Cu:35Mo, and 40Cu:40Mo, with fixed 15WC:5Si. The results indicate that even a 5 wt.% variation of copper significantly affects the coating output responses. At 3 A current the 50Cu:30Mo combination shows lowest roughness of 2.4 μm, followed by 3.2 μm, and 5.4 μm roughness with 45Cu:35Mo and 40Cu:40Mo. Coating with 50Cu:30Mo ratio shows the highest wear reduction, achieving a 3-fold decrease compared to the uncoated Al-2014. Furthermore, coated samples depict a 42% reduction in corrosion rate compared to uncoated sample. Experimental results suggest that the briquette with a higher copper percentage (50 wt.%) provides a more suitable coating.

Ionic Liquid-Modified Copper for the Enhanced Thermal Conductivity and Mechanical Properties of Epoxy Resin/Expanded Graphite Composites.

In this study, diglycidylether of bisphenol A (DGEBA)/expanded graphite (EG)/copper (Cu) powder composites with high thermal conductivity were prepared for use as thermal interface materials. To construct an excellent thermally conductive network, the Cu surface was modified using the ionic liquid 1-ethyl-3-methyl imidazolium dicyanamide. In addition, the effect of the Cu content on the thermal conductivity, thermal stability, flexural properties, impact strength, and morphologies of the DGEBA/EG/Cu composites was investigated. The results indicated that the addition of 10 wt % Cu increased the thermal conductivity of the composites from 7.35 to 9.86 W/(m·K). Conversely, the thermal stability of the composites decreased with the addition of Cu. The flexural strength and impact strength of the composites increased from 27.9 MPa and 0.81 kJ/m2 to 39.6 MPa and 0.96 kJ/m2, respectively, as the Cu content increased from 0 to 10 wt %. Moreover, the flexural modulus of the composites increased from 9632 to 11,309 MPa with the addition of 10 wt % Cu. Scanning electron microscopy analysis of the DGEBA/EG/Cu composites revealed sheet-shaped blocks with numerous microcracks on the fracture surfaces.

Laser Powder Bed Fusion of Copper-Tungsten Powders Manufactured by Milling or Co-Injection Atomization Process.

The processing of pure copper (Cu) has been a challenge for laser-based additive manufacturing for many years since copper powders have a high reflectivity of up to 83% of electromagnetic radiation at a wavelength of 1070 nm. In this study, Cu particles were coated with sub-micrometer tungsten (W) particles to increase the laser beam absorptivity. The coated powders were processed by powder bed fusion-laser beam for metals (PBF-LB/M) with a conventional laser system of <300 watts laser power and a wavelength of 1070 nm. Two different powder manufacturing routes were developed. The first manufacturing route was gas atomization combined with a milling process by a planetary mill. The second manufacturing method was gas atomization with particle co-injection, where a separate W particle jet was sprayed into the atomized Cu jet. As part of the investigations, an extensive characterization of powder and additively manufactured test specimens was carried out. The specimens of Cu/W powders manufactured by the milling process have shown superior results. The laser absorptivity of the Cu/W powder was increased from 22.5% (pure Cu powder) to up to 71.6% for powders with 3 vol% W. In addition, a relative density of test specimens up to 98.2% (optically) and 95.6% (Archimedes) was reached. Furthermore, thermal conductivity was measured by laser flash analysis (LFA) and thermo-optical measurement (TOM). By using eddy current measurement, the electrical conductivity was analyzed. In comparison to the Cu reference, a thermal conductivity of 88.9% and an electrical conductivity of 85.8% were determined. Moreover, the Vickers hardness was measured. The effect of porosity on conductivity properties and hardness was investigated and showed a linear correlation. Finally, a demonstrator was built in which a wall thickness of down to 200 µm was achieved. This demonstrates that the Cu/W composite can be used for heat exchangers, heat sinks, and coils.

Simultaneous electro-chemical detection of Pb and Fe by copper-modified carbon paste electrode in the portion of soil

A carbon graphite and copper powder paste electrode (CPE-Cu) was successfully designed as a working electrode for electrochemical analysis. The structural characteristics of this electrode were revealed by X-ray diffraction. Voltammetric techniques and electrochemical impedance spectroscopy were used to assess the electroactivity of the proposed working electrode. X-ray diffraction showed that the composite material has a slightly different crystalline structure to pure graphite, since the copper modification influenced the angles of reflection so that they fluctuated towards slightly larger values. The study of the electrochemical behaviour of the CPE-Cu electrode using cyclic voltammetry showed that the redox phenomena at the electrode surface are almost reversible. Analysis of the soil portion using cyclic voltammetry showed that lead (II) and iron (II) showed current peaks at potentials −0.36 V and +0.12 V respectively. These potentials were confirmed by square-wave voltametry. Cyclic voltammetry and square wave voltammetry showed linearity between the portion of soil in the soil and the electrochemical response. In addition, the study of the effect of the scanning speed showed that the reactions at the working electrode are controlled by a diffusion phenomenon at the surface of the working electrode. Electrochemical impedance spectroscopy showed that the electrode material had a low resistance to charge transfer, with a complete analysis of around 80 ohm.cm2. The heavy metals Cd2+, Pb2+ and Fe2+ were detected simultaneously at trace levels. Calculations of the detection limits for Pb2+ and Fe2+ gave 0.709 ppm and 0.821 ppm respectively. At the end of this work, it can be said that the proposed sensor can be used as an instrument for monitoring the metals studied, as the detection limits were relatively low despite the complexity of the detection medium (portion of soil).

The efficiency of solar stills with copper-coated sponge cubes for water desalination: A comparative study

Water scarcity within the world may be an enormous threat to living beings. Potable water can be produced by renewable energy using solar desalination. In the quest for efficient water desalination methods, researchers have turned to solar stills as a promising solution. One approach to enhancing the productivity of solar stills is the utilization of copper-coated sponge cubes. These cubes, when integrated into the still, provide extended heating periods, leading to higher temperature differences. This, in turn, improves freshwater production by improving the performance of the modified still. In this work, three basin-type solar stills of each 0.5 m2 area have been studied experimentally in the location of Coimbatore, Tamil Nadu. Comparative studies were done between the solar still modified with sponge materials and the modified solar still with sponges coated with copper powder. In these experimental studies, the various performance characteristics related to solar still efficiency have been examined. The sponges were placed inside the water of the basin. The commercially available copper powder was prepared like a paste and coated in the sponges, and it was increased in size to 0.005 m on all sides. The sponges pasted with copper powder reduce the energy losses from the still due to its high thermal conductivity and the evaporation rate also increased by the capillary action of the sponge. High heat transfer to water also occurred due to the addition of copper powder. From the comparative studies, the solar still with sponge materials coated with copper powder gives a higher yield. The proposed solar still with modifications improves efficiency. The solar still without modification gives a yield of 1.3 kg/day, the modified still with sponges gives an output of 1.5 kg/day and the modified still with copper-coated sponges gives an output of 2.35 kg/day. The copper-coated sponge cubes placed still produced an efficiency of 60.07%.

Analysis of Wear Resistance of Metallic-Reinforced Polyurethane Resin Composites for Sheet Metal Forming

Abstract The paper presents the results of testing the wear resistance and coefficient of friction (COF) tools made of SikaBeresin® F50 polyurethane resin intended for dies and punches for the cold sheet metal forming process. Seven sets of composite tools (rotating rings) additionally reinforced with waste metallic powders from Al and Cu alloys (5-20% by volume) from the dry cutting process of pipes and rods were tested. Wear resistance tests and determination coefficient of friction were carried out using the T-05 block-on-ring tribotester. The tests were performed for heat and corrosion resistant sheets made of nickel alloy AMS5599 (Inconel 625), iron alloy AMS5510 (321) and aluminum alloy sheets AMS4026 (6061-T4). Composite tools with the addition of 20% aluminum powder (A+B+C+20%Al) tested with a specimen of steel alloy AMS5510 and nickel alloy AMS5599 were characterized by the lowest wear resistance. In each case, the composite rotating ring without reinforcements was characterized by the lowest coefficient of friction. The use of Cu powder reinforcements in each case had a positive effect on increasing wear resistance. The best wear resistance of 0.011% was obtained for composite rotating ring with the addition of 10% copper powder paired with specimen of nickel alloy AMS5599 sheet.

On The Potential Use of Copper-Modified Geopolymer Incorporating Lead-Smelter Slag for Thermal Energy Storage

Thermal energy storage (TES) system has been widely employed in concentrated solar power (CSP) plants to ensure the system efficiency. With excellent thermal characteristics, electrolytic copper powder (ECP), graphene oxide (GO) and lead-smelter slag (LSS) aggregate – a mining waste material, have been utilised in this study, aiming to fabricate metallurgical geopolymer material as a storage medium in the TES system. This paper investigated the effect of ECP contents (0, 5%, 10%, 15%, 20%) on the strength, specific heat, thermal conductivity and thermal stability of GO-engineered geopolymer mixes incorporating LSS aggregate. With 10% ECP inclusion, the flow rate and compressive strength improved significantly. Increasing ECP content improved the thermal conductivity but reduce specific heat of geopolymers. The results revealed that ECP was a promising component to be incorporated into geopolymer to enhance its physio-mechanical characteristics and thermal stability. The combination of ECP, GO and LSS to produce geopolymer materials for TES system can provide an eco-friendly solution to the CSP plants and the industry waste recovery.

Peridynamics simulation of microparticle impact: Deformation, jetting, and the influence of surface oxide layer

Over the past decade, cold spraying (CS) has become a significant additive manufacturing technology for creating metallic structures and repairing damaged components. This study uses a novel peridynamic model to investigate the behavior of 12 μm copper particles impacting a copper substrate during CS deposition. The model examines deformation behavior, material jetting, and the effect of a native particle oxide layer. Two oxide thicknesses, 6 nm and 30 nm, were considered. The 6 nm oxide, typical for gas-atomized copper powders, had a negligible effect on deformation, while the 30 nm oxide showed a notable influence. For the 30 nm oxide, the experimentally observed coefficient of restitution (COR) deviated from theoretical predictions in the velocity range of 400–600 m/s due to cracking and fracturing of the oxide layer at higher impact velocities, reducing particle rebound velocity without sufficient metal-to-metal contact for permanent bonding. Permanent adhesion requires significant oxide fragmentation and separation. The study also identified threshold velocities for material jetting from the substrate and particle, showing that oxide presence delays particle jetting by impeding plastic deformation at the edges. Quantifying the oxide volume at the particle-substrate interface clarifies the effect of jetting on COR and bonding strength. The analysis includes effects of deflected jets at extremely high velocities (e.g., 870 m/s), compared with existing literature. Overall, the results demonstrate the efficacy of the peridynamics-based simulation in accurately representing material behavior during high-velocity impacts, effectively predicting oxide breakup, detachment, and removal in CS, and their effects on deposition characteristics.

Enhanced compressive strength of graphene strengthened copper (G/Cu) composites

This study explores the compressive mechanical properties of copper composites reinforced with graphene. Graphene was synthesized on copper powders via plasma-enhanced chemical vapor deposition. Multilayer graphene formation has been substantiated by Raman analysis. Graphene-coated copper (G/Cu) powders were then subjected to pressing and sintering to fabricate G/Cu composites. The mechanical properties of G/Cu composites were investigated under compression from room temperature up to 400 °C in air. The results demonstrated a substantial improvement in the mechanical properties of G/Cu composites compared to monolithic copper. Specifically, the yield strength in compression of the G/Cu composite increased by 203% at room temperature and by 190% at 200 °C. At 400 °C, the yield strength enhancement exceeded 370%. Microstructural analysis suggests that the observed enhancements in G/Cu composites can be attributed to reduced porosity, smaller grain size, and inhibited dislocation motion at the increased grain boundary area (due to refined grain size) and graphene-copper interfaces.

Improved thermal conductivity of high‐density polyethylene by incorporating hybrid fillers of copper powders and silicon carbide whiskers

AbstractIn this paper, highly electrically and thermally conductive copper powders (Cu) and electrically insulative yet thermally conductive silicon carbide whiskers (SiCw) were selected as functional fillers and high‐density polyethylene (HDPE) was used as the matrix to prepare thermal conductive composites. By controlling the amount of Cu at 30 vol% which is below percolation threshold, the volume resistivity of the composites is maintained above 1014 Ω cm. The results showed that SiCws entered the area which was not occupied by Cu particles and they played a bridging effect among Cu particles, thereby promoting the formation of intact thermal conductive pathways that contributed to improving the thermal conductivity of corresponding composites. The combination of SiCw:Cu = 3:1 at a filler content of 30 vol% resulted in a thermal conductivity as high as 1.921 W/mK, which is 380% higher than pure HDPE.

RETRACTED: Vorotilo et al. Manufacturing of Conductive, Wear-Resistant Nanoreinforced Cu-Ti Alloys Using Partially Oxidized Electrolytic Copper Powder. Nanomaterials 2020, 10, 1261.

The Nanomaterials Editorial Office retracts the article, "Manufacturing of Conductive, Wear-Resistant Nanoreinforced Cu-Ti Alloys Using Partially Oxidized Electrolytic Copper Powder" [...].

Study on Energy Transfer Mechanism of Grinding Balls in a Planetary Ball Milling System

Planetary ball milling systems (PBMSs) have become novel and high-energy milling equipment with wide applications. The present study explores the energy transfer mechanisms of grinding balls in these systems. A theoretical model has been developed by considering essential factors such as the diameter of the grinding balls and milling conditions, based on previous models and molecular dynamics simulations. To validate and improve the theoretical model, experimental data was collected by examining the impact of different grinding ball diameters on the change in copper powder particle size under controlled milling conditions. The mechanisms under particle size changes have been revealed, providing a deeper understanding of energy transfer in PBMSs and establishing a direct connection between the grinding ball diameter and the particle size of the resulting product. This research method makes it possible to predict the particle size and performance of the ball-milled product.

Experimental study of the optimal mixing ratio of metallic additives for improving the performance of the solar activated carbon-methanol adsorption refrigeration system

An activated carbon–methanol system can run on low heat (70–100°C). Methanol is dependable and works well with activated carbon because of several benefits, including an appropriate latent heat of evaporation, a low freezing point, and negligible copper corrosion and steel at temperatures below 100 °C. An experimental study of the thermal performance by increasing the adsorption bed thermal conductivity was conducted. Using0 10 % 20 and %30 % of metallic copper powder with activated carbon to improve the bed thermal conductivity. A sample is prepared with 20 % copper powder to find out the improvement of heat transfer characteristics to the cooling effect. The temperature gradient has been tested with two flow rates to examine the coolant performance and increase. Solar energy can be effectively utilized based on low-grade temperature consumption in such systems. This work aims to make an experimental investigation of the thermal performance of an activated carbon-methanol adsorption refrigeration system to study the effect of the enhanced thermal conductivity of the adsorbing bed. Using 0 %, 10 %, 20 %, 30 % of metallic copper powder with activated carbon to enhance the thermal conductivity of the bed, providing a significant improvement in the system efficiency, specific cooling power (SCP), and coefficient of performance of adsorption cooling. It is found that copper filing with a mass concentration of 20 % are appeared the optimal ratio metallic additive to enhance the thermal performance of the system. Moreover, the effect of the hot water flow rate is studied. Results indicated that the addition of 20 % metallic copper filings to the activated carbon lowered the evaporator temperature to reach -5 and -10 °C for heating water flow rates 3 and 2 LPM, respectively. Also, the addition of copper filing enhances the cycle COP of the system by 49 % and 46 % at hot water flow rates of 2and 3 LPM, respectively. The highest cycle COP of the current system reached was 0.92 for the condition 20 % additives at 3 LPM hot water flow rate. Owning the feature of great solar energy availability and the long daily sunny hours, solar-powered adsorption cooling systems have promising potential applications in Egypt. A mathematical model of the system performance is also studied.