Conventional Resistance Research Articles

Abstract LB020: Extracellular vesicle-mediated intrinsic induction of ferroptosis causes reversal of chemoresistance in lung cancer

Abstract Introduction: Resistance to chemotherapeutic drugs is the major cause of treatment failures and high mortality in lung cancer(LC). Thus, strategies to overcome chemoresistance is the major thrust area of cancer research. Ciplatin (CDDP) is the first line of chemotherapeutic interventions in lung cancer however, the treatment benefit diminishes due to develop resistance against the drug. Dysregulation of apoptosis is the major reason for developing chemoresistance. Ferroptosis is a recently discovered form of non-apoptotic regulated cell death (RCD) that can overcome the apoptosis mediated resistance. To exploit this our laboratory has developed a novel Extracellular Vesicle (EV)-iron oxide nanoparticle (IONP) hybrid system- 'ExoFeR,' that can induce ferroptosis. Experiments conducted on LC cells and patient derived tumoroids (PDTs) have shown reversal of CDDP resistance after ExoFeR treatment. Our study demonstrates the utility of ferroptosis as alternate treatment intervention for treating chemoresistant LC tumors. Materials and methods: EVs derived from normal lung fibroblast cells (MRC9) were loaded with IONPs. The complex was characterized by Transmission electron microscopy (TEM), Inductively coupled plasma mass spectrometry (ICP-MS) and through Zeta potential measurements. The induction ferroptosis by ExoFeR was confirmed in Non-Small Cell Lung Cancer (NSCLC) A549 cells and NSCLC PDTs by Prussian blue, FerroOrange, and Mito-FerroGreen staining. Further, ferroptosis markers like GPX4 and SCL7A11/xCT were evaluated to examine the induction of ferroptosis. Finally, A549 cells and resistant NSCLC PDTs were tested for sensitivity to chemo drugs. Results: Physicochemical characterization indicated the successful formulation of ExoFeR. Reduction in the expression level of SLC7A11/xCT- and GPX4 proteins in ExoFeR-treated NSCLC cells and PDTs suggested induction of ferroptosis which also showed sensitization of chemo drug (cisplatin). Summary/Conclusion: We report here the synthesis of a novel EV-IONP-based system that can intrinsically induce ferroptosis and overcome chemoresistance by circumventing the conventional apoptosis-based resistance. Our finding is expected to develop a potent cancer treatment strategy for efficiently treating resistant NSCLC tumors. Citation Format: Akhil Srivastava, Anjugam Paramananantham, Rahmat Asfiya. Extracellular vesicle-mediated intrinsic induction of ferroptosis causes reversal of chemoresistance in lung cancer [abstract]. In: Proceedings of the American Association for Cancer Research Annual Meeting 2024; Part 2 (Late-Breaking, Clinical Trial, and Invited Abstracts); 2024 Apr 5-10; San Diego, CA. Philadelphia (PA): AACR; Cancer Res 2024;84(7_Suppl):Abstract nr LB020.

Bacterial Leaf Spot Susceptibility Screening of Chili Pepper Cultivars Using qPCR Determination of Xanthomonas euvesicatoria pv. euvesicatoria Titers.

Bacterial leaf spot is a serious disease of chili pepper (Capsicum spp.) caused by Xanthomonas euvesicatoria pv. euvesicatoria. Conventional resistance screening is time and resource intensive. It was considered that a quick and simple determination of cultivar susceptibility could be achieved through estimating bacterial titers of inoculated plants. A SYBR quantitative polymerase chain reaction (qPCR)-based assay was compared with conventional PCR, then used to detect and enumerate pathogen titers in serial dilutions and DNA extracted from infected plant leaves. The qPCR detection limit was approximately 1 CFU µl-1, 10 times more sensitive than conventional PCR. A linear correlation (R2 = 0.994) was obtained from the standard curve comparing plate-truthed serial dilutions of the pathogen with the qPCR cycle threshold. Six strains were used to inoculate cultivars Hugo and Warlock. One strain, X. euvesicatoria pv. euvesicatoria BRIP62403, was consistently the most virulent based on visual symptoms and pathogen titers in planta inferred by qPCR performed on DNA extracted from infected leaves 2 and 6 weeks postinoculation. Visual observations 6 weeks after inoculation were highly correlated (R2= 0.8254) to pathogen titers. The qPCR method was used to categorize 20 chili pepper cultivars 2 weeks after inoculation. A high positive correlation (R2 = 0.6826) was observed between visual scoring and pathogen titers from 20 chili pepper cultivars, facilitating categorization of susceptible, intermediate, and resistant cultivars. The qPCR approach developed here facilitates susceptibility screening of chili pepper cultivars at an early stage of selection and could be readily adapted to a range of other pathosystems.

Analysis of metal and zinc oxide semiconductor interface resistance using transmission line method

The transmission line method (TLM) is modified to analyze the contact resistance between the metal and zinc oxide semiconductor considering interface resistance. TCAD is used to simulate an ideal defect-less state and compare it with experimental result. It is found that the current transfer length can be overestimated in conventional TLM measurement. The importance of interface resistance is shown through interface trap and Schottky contact effect analysis: Resistance comparison between different metal used device, and the activation energy shift measurement after O2 pre-annealing. Based on these, the conventional resistance equation for TLM is corrected by separating channel resistance and non-ideal contact resistance. The mobility and temperature coefficient of resistance (TCR) of ZnO channel are extracted using the suggested method. This shows the importance of metal/semiconductor interface resistance in devices using semiconductor channel.

Stem Rust: An Evolving Threat to Wheat and Strategies for Its Management

Ug99, a menacing strain of stem rust, emerged as a specter haunting wheat fields worldwide. Its arrival in Uganda in 1999 sent shockwaves through the agricultural community, raising alarm bells for the vulnerability of vital wheat crops. This formidable adversary, armed with mutations that defy conventional resistance in wheat, poses a substantial threat to global food security. The super strain, the ability of Ug99 to swiftly overcome resistant varieties propelled an urgent quest for new, innovative defense strategies. Researchers and scientists mobilized in a race against time, collaborating across borders to develop resistant wheat varieties capabale of withstanding Ug99’s destructive might. The battle against this potent rust strain symbolizes a relentless pursuit to protect the world’s wheat supply, ensuring sustenance for generations to come. This review delved into Stem Rust’s past to present: history, life cycle, control measures especially marker assisted selection for controlling its pace.

Multimodal and conventional resistance training interventions improve muscle function in older adults: Findings from the Training IMCT study

Age-associated remodeling processes affect the intramuscular connective tissue (IMCT) network, which may significantly impair muscle function. Thus, we aimed to test whether including exercises shown to efficiently target the IMCT to a conventional resistance exercise intervention (CONV) would result in greater functional gains as compared to CONV alone. Fifty-three men and women (66.2 ± 3.3 years) were assigned to either CONV (n = 15), multimodal training (MULTI; n = 17) or a control (CTRL; n = 21) group. All subjects were tested at baseline, and those assigned to CONV or MULTI underwent a 16-week training intervention. The CONV group followed a progressive resistance training program, in which the number of weekly training sessions gradually increased from 1 to 3. In the MULTI group, one of these sessions was replaced with plyometric training, followed by self-myofascial release. Testing included maximal strength and power, imaging-based muscle volume, architecture, and functional performance. The intervention effects were analyzed using two- or three-way repeated measures ANOVA models (α = 0.05). Briefly, the maximal knee extension isometric contraction, one-repetition maximum, and isokinetic peak torque increased in all groups (p < 0.05), albeit to a lesser extent in CTRL. On the other hand, quadriceps femoris muscle volume (p = 0.019) and vastus lateralis pennation angle (p < 0.001) increased only in the MULTI group. Handgrip strength did not change in response to the intervention (p = 0.312), whereas Sit-to-Stand performance improved in all groups after the first 8-wks, but only in MULTI and CONV after 16-wks (all p < 0.001). In conclusion, we found that a resistance training intervention in which one weekly training session is replaced by plyometric training is feasible and as effective as a program consisting solely of conventional strength training sessions for inducing gains in muscle strength and function in older adults. Muscle size and architecture improved only in the MULTI group. German Clinical Trials: DRKS00015750.

PenA profile of Neisseria gonorrhoeae in Guangdong, China: Novel penA alleles are related to decreased susceptibility to ceftriaxone or cefixime

Resistance to extended-spectrum cephalosporins (ESCs) has become a public health concern with the spread of Neisseria gonorrhoeae and increasing antimicrobial resistance. Mutation of penA, encoding penicillin-binding protein 2, represents a mechanism of ESC resistance. This study sought to assess penA alleles and mutations associated with decreased susceptibility (DS) to ESCs in N. gonorrhoeae. In 2021, 347 gonococci were collected in Guangdong, China. Minimum inhibitory concentations (MICs) of ceftriaxone and cefixime were determined, and whole-genome sequencing and phylogenetic analysis were performed. Multi-locus sequence typing (MLST) and conventional resistance determinants such as penA, mtrR, PonA and PorB were analysed. penA was genotyped and sequence-aligned using PubMLST. Genome-wide phylogenetic analysis revealed that the prevalence of DS to ESCs was highest in Clade 11.1 (100.0%), Clade 2 (66.7%) and Clade 0 (55.7%), and the leading cause was strains with penA-60.001 or new penA alleles in clades. The penA phylogenetic tree is divided into two branches: non-mosaic penA and mosaic penA. The latter contained penA-60.001, penA-10 and penA-34. penA profile analysis indicated that A311V and T483S are closely related to DS to ESCs in mosaic penA. The new alleles NEIS1753_2840 and NEIS1753_2837 are closely related to penA-60.001, with DS to ceftriaxone and cefixime of 100%. NEIS1753_2660, a derivative of penA-10 (A486V), has increased DS to ceftriaxone. NEIS1753_2846, a derivative of penA-34.007 (G546S), has increased DS to cefixime. This study identified critical penA alleles related to elevated MICs, and trends of gonococcus-evolved mutated penA associated with DS to ESCs in Guangdong.

Pine-like elastic metamaterials for urban seismic Rayleigh wave attenuation

Preventing urban regions from seismic wave destruction is of paramount significance because it is closely related to urban lifeline and prosperity of cities. Almost all conventional seismic resistance approaches rely on the stiffness and strength of buildings, which require excessive structural components with additional self-weights. In this study, we propose a pine-like seismic metamaterial for efficient attenuation of surface Rayleigh waves. The pine arrays in suburban regions demonstrate an ability to convert Rayleigh waves to shear bulk waves or attenuate waves on the surface via local resonation. This property originates from a gradient design of pine arrays, where a scale ratio is defined to tune the geometric properties of each pine unit. Specifically, a gradient pine array with a scale ratio smaller than one can interact with the Rayleigh waves and convert them to shear waves that propagate deep to underground. The transmission ratio of the entire system indicates a broadband wave attenuation at subwavelength scale. It reveals that the pine is able to couple with a certain elastic Rayleigh wave whose wavelength is much larger than the lattice constant, which is rarely achieved in any conventional civil engineering structures such as open trench barriers and filled trench barriers. Additionally, a numerical model of an urban region and suburban pine array is established and analyzed. Infrastructures and structures in a city that suffer direct Rayleigh wave interference run into a high risk of structural destruction as compared to urban structures protected with suburban metamaterial pine arrays. Finally, two real earthquake wave signals are used to validate the efficiency of the pine arrays in dissipating earthquake energy. The approach in this paper can be extended to deal with more complex naturally available structures for examining the elastic wave attenuation abilities of these novel structures.

Niosomal-Based Drug Delivery Platforms: A Promising Therapeutic Approach to Fight Staphylococcus aureus Drug Resistance

Staphylococcus aureus, a prominent bacterial pathogen, presents formidable medical challenges owing to its rapid development of resistance. The emergence of multidrug resistant (MDR) S. aureus strains has become a pressing concern for healthcare systems, driving researchers to explore novel therapeutic strategies for managing infections associated with this pathogen. In this pursuit, niosomal-based platforms have emerged as promising candidates to effectively target S. aureus and fight conventional antimicrobial resistance. Niosomes comprise a bilayer membrane formed by nonionic surfactants, which can encapsulate both hydrophilic and hydrophobic drugs. These nanoparticles are known as vesicular delivery systems and have many advantages, such as low cost, less toxicity, and more flexibility and stability. Moreover, niosomes, being an effective drug delivery system, can directly interact with the bacterial cell envelope, thereby enhancing the pharmacokinetic activities of drugs at infected sites. A niosome-based delivery system can effectively treat S. aureus infections by destroying the biofilm community, increasing intracellular targeting, and enhancing the antibacterial activity. The main mechanisms of action of niosomes against resistant S. aureus strains involve the ability to resist enzymatic degradation, controlled release profile, and targeted drug delivery, which can provide an effective dosage of antimicrobial agents at the site of actions. In addition, niosomes have the potential to transfer wide-spectrum materials from different classes of antibiotics to nonantibiotic antimicrobial agents, such as natural compounds, antimicrobial peptides, and metallic nanoparticles. The combination of polymeric materials in the structure of a niosomal formulation could improve their bioavailability, loading capacity, and therapeutic efficacy for different applications. Furthermore, niosomes could find application in photodynamic therapy, offering a promising alternative to conventional treatments for eradicating drug-resistant S. aureus isolates. Finally, niosomal nanocarriers can be developed for delivering the drugs to desired sites by different routes of administration and could be considered a powerful strategy for overcoming the therapeutic obstacles caused by MDR S. aureus.

A novel indirect optical method for rock stress measurement using micro-deformation field analysis

Stress measurement plays a crucial role in geomechanics and rock engineering, especially for the design and construction of large-scale rock projects. This paper presents a novel method, based on the traditional stress relief approach, for indirectly measuring rock stress using optical techniques. The proposed method allows for the acquisition of full-field strain evolution on the borehole's inner wall before and after disturbance, facilitating the determination of three-dimensional (3D) stress information at multiple points within a single borehole. The study focuses on presenting the method's theoretical framework, laboratory validation results, and equipment design conception. The theoretical framework comprises three key components: the optical imaging method of the borehole wall, the digital image correlation (DIC) method, and the stress calculation procedure. Laboratory validation tests investigate strain field distribution on the borehole wall under varying stress conditions, with stress results derived from DIC strain data. Remarkably, the optical method demonstrates better measurement accuracy during the unloading stage compared to conventional strain gauge methods. At relatively high stress levels, the optical method demonstrates a relative error of less than 7% and an absolute error within 0.5 MPa. Furthermore, a comparative analysis between the optical method and the conventional contact resistance strain gauge method highlights the optical method's enhanced accuracy and stability, particularly during the unloading stage. The proposed optical stress measurement device represents a pioneering effort in the application of DIC technology to rock engineering, highlighting its potential to advance stress measurement techniques in the field.

Effect of Electrical Resistance Heating on Recrystallization of Cold-Rolled Low-Carbon Steel

The “electron wind effect” has long been cited as a potential catalyst of solid-state transformations in metals, particularly when high current densities are involved. However, the literature exploring similar effects at lower current densities, such as those occurring during Gleeble thermomechanical simulation, remains scarce. The present work compares recrystallization activity in cold-rolled low-carbon steel during heat treatment by conventional furnace versus direct resistance heating (Gleeble). Multiple levels of cold work, annealing durations, and soak temperatures were examined, allowing for an in-depth comparison of recrystallization rates and activation energies between samples subjected to identical time–temperature profiles in the furnace and Gleeble. In addition to the expected increase in recrystallization behavior with the increases in temperature and cold-reduction levels, the use of the Gleeble system as the heating method resulted in faster initial microstructural transformation than a conventional furnace. The variability in recrystallized fractions persisted until the microstructures had saturated to their nearly fully recrystallized levels, at which point the microhardness and electron backscatter diffraction (EBSD) revealed convergence to equivalent behavior irrespective of the heating method. Analysis of the recrystallization kinetics by fitting to a JMAK relationship reflected the increased transformation activity during Gleeble treatment, with the value of the kinetic exponent also indicating greater grain growth activity at higher temperature.

Shoulder vibratory exercises improves shoulder external rotation muscle strength and shoulder function: Randomized comparison trial.

Based on electromyography measurements, shoulder vibratory exercises efficiently stimulate shoulder muscles activity. Yet very few studies have supported that shoulder vibratory exercises increased shoulder muscles strength and function, and the noninferiority compared with conventional elastic resistance exercises remains unknown. This study investigated the effect of vibratory exercises versus conventional elastic resistance exercises with elastic bands on shoulder external rotation muscles strength and functional performance in young adults. 26 young adults (7 males and 19 females, with age 23.89 ± 3.02) were recruited and randomly allocated to shoulder vibratory exercises with FLEXI-BAR (FLEXI-BAR group) or conventional resistance exercises with elastic band (TheraBand group) for 3 times/week, 4 weeks totally. Shoulder external rotator muscles strength test and Underkofler softball distance throw test (USDTT) were performed before and after the training period. After 4 weeks training, shoulder external rotator muscles strength increased 22.25 ± 15.06 N (P= 0.004, effect size = 1.48) within FLEXI-BAR group and 22.81 ± 14.94 N (P= 0.007, effect size = 1.53) within TheraBand group. There were no statistically significant differences between groups in the three muscle strength tests (P> 0.65). Regarding shoulder function, FLEXI-BAR exercises increased the throw distance 0.81 ± 0.92 meters in USDTT (P= 0.041, effect size = 0.88) while TheraBand exercise did not (P= 0.284), yet there was no statistically significant between group effects (P= 0.608). These findings suggest that shoulder vibratory exercises can improve shoulder muscles strength in young adults and can be a useful alternative to the conventional elastic resistance exercises to improve the shoulder muscles strength and function. This provides therapists with more options in terms of choosing training equipment for rehabilitation programs.

The rapid densification behavior of powder metallurgy Ti alloys by induction heating sintering

Micropores are decisive to mechanical properties and thermal deformation capabilities of powder metallurgy (P/M) Ti alloys sintered compacts. As a result, achieving express densification is of prime importance and has attracted increasing attention recently. Induction heating owns the merits of high efficiency, short process, and low cost, and thus has huge potential to be used as a sintering approach for the fabrication of P/M Ti alloys. Nevertheless, the facilitated densification behavior associated with induction heating sintering remains unclear so far. To address it, powder metallurgy Ti6Al4V is manufactured via induction heating sintering with which the underlying sintering mechanism is investigated in-depth. It is found that induction heating could generate a fully densified compact in a remarkably shortened time, demonstrating its superior sintering efficiency as compared with conventional resistance furnace heating. COMSOL finite element analysis reveals that the maximum current density during induction heating can reach 106 A m–2 though the magnetic field strength is solely 0.02 T, leading to a slight temperature difference of approximately 30 °C between the interior and exterior of the billet. Furthermore, the rapid heating essentially starts at sharp corners of particles due to the potent current concentration effect, which facilitates the cracking of the particle surface oxide film and thus enhances the direct contact between them. Moreover, the electromigration effect caused by induction current promotes the diffusion capability of elements, giving rise to expedited densification, alloying, and chemical homogenization. This work provides not only critical insight into the sintering mechanism of induction heating sintering but also significant guidance for low-cost powder metallurgy materials preparation.

Construction and functional verification of size-reduced plasmids based on TMP resistance gene dfrB10.

Plasmid size is one of the factors affecting transfection efficacy in most of the molecular genetic research studies. One effective approach for reducing plasmid size is to replace relatively large, conventional antibiotic resistance genes with the short-size dfrB10 gene. The successful construct of a series of dfrB10-based tool plasmids and their functional validation, via comparison with original plasmids, suggest that dfrB10 is a potent drug resistance selection marker. The antibiotic trimethoprim offers convenient usage comparable to that of ampicillin or kanamycin. Additionally, fluorescence analysis has demonstrated the compatibility of TMP with protein expression in various host cells. Based on these findings, TMP-dfrB10 could be an alternative choice for future use in molecular genetic research studies that require miniature plasmids to achieve optimal results.

Muscle Mass and Muscle Strength Following 6 Weeks of Blood Flow Restriction Combined with Low-Intensity Strength Training in Overweight Adolescents

Background and Study purpose. Blood flow restriction training is a new training technique that involves low-intensity exercise and can generate physiological changes equivalent to high-intensity exercise. The aim of this study is to assess the impact of blood flow restriction in conjunction with low-intensity resistance exercise on muscle mass and muscle strength among overweight adolescents, in comparison to conventional resistance exercise. Materials and methods. The study involved two randomized groups: an experimental group, which performed 40% of one repetition maximum (1RM) resistance exercise combined with 60% of arterial occlusion pressure (AOP), and a traditional resistance exercise group, which performed 70% of 1RM resistance exercise. All participants underwent pre-test and post-test evaluations for body composition, 1RM, and muscle circumference. The training program lasted for six weeks and consisted of upper and lower body training, including exercises such as leg press, leg curl, arm curl, and arm extension. Results. The group that underwent low-load blood flow restriction (LLBFR) training showed a notable increase in muscle mass (p&lt;0.049) as well as arm and leg circumference (p&lt;0.047 and p&lt;0.046, respectively) compared to before the training program, similar to the results of high-intensity resistance exercise. Conclusions. Combining blood flow restriction with low-intensity resistance training is a potentially effective approach to increase muscle size and strength, especially in overweight adolescents. Moreover, this type of training can decrease the amount of exercise load, making it a feasible option for individuals who may not tolerate high loads due to certain medical conditions or other limitations.

Increase of electrode life in resistance spot welding of aluminum alloys by the combination of surface patterning and thin-film diffusion barriers

When resistance spot welding aluminum alloys, high electrode forces are required to reduce the electrical contact resistances between the electrodes and the sheet metals. The high contact resistances and the resulting thermal load cause extensive degradation of the electrode working faces. Weld spatter occurs after only a few weld cycles, significantly reducing the quality of the weld. Conventional resistance welding machines are limited in terms of maximum electrode force and weld current. As a result, weld quality and electrode life are inadequate. The aim is to increase the achievable electrode life by surface patterning the electrode working faces and creating thin-film diffusion barriers by physical vapor deposition (PVD). Patterning is intended to penetrate the oxide layers of the aluminum sheets and increase the proportion of electrically conductive contact areas. The different influences of patterning by particle blasting and contour turning will be investigated. As a further approach, thin-film diffusion barriers of up to 3 μm are deposited on the electrodes to prevent direct Al-Cu contact. Therefore, metallic coating materials (Ni and W) and an electrically highly conductive ceramic coating material (TiB2) are investigated. The combination of electrode patterning and thin-film diffusion barriers is tested in electrode life studies. It is shown that these modified electrode working faces can limit degradation effects and contribute to an increase in electrode life. In addition, the weld quality can be improved compared to the reference condition.

Effects of blood-flow restricted exercise versus conventional resistance training in musculoskeletal disorders—a systematic review and meta-analysis

ObjectiveTo compare the effect of low-load blood flow restricted resistance training (BFR-RT) versus high-load resistance training (HL-RT) on muscle strength, muscle mass, physical function, patient-reported outcomes, and adherence to training in clinical musculoskeletal populations.Data sourcesWeb of Science, Cochrane Central, Medline, Embase, SportDiscus was searched on the 30th May 2022.Review methodsThis study was conducted as a systematic review and meta-analysis. Randomized Controlled Trials (RCTs) were included if they (i) included patients, (ii) comprised of a BFR-RT intervention protocol and a group who performed HL-RT (≥ 70%1RM) for at least eight exercise sessions, and (iii) involved at least 1 exercise that targeted the lower limbs. The Cochrane Risk of Bias tool was used to evaluate the risk of bias. The meta-analyses were performed using a random effects model with an adjustment to the confidence interval.ResultsSeven RCTs comprising 303 participants (BFR-RT: n = 151; HL-RT: n = 152) were identified. HL-RT and BFR-RT showed similar gains in dynamic (1-10RM) knee extensor strength and leg press strength, quadriceps cross sectional area, sit-to-stand performance, and patient reported pain and function. There was a moderate effect favoring BFR-RT for increasing maximal isometric knee extensor strength. The grading of certainty in evidence was low-to-very low for all outcome variables.ConclusionThis systematic review and meta-analysis extends our current knowledge about BFR-RT and HL-RT as equally effective exercise methods for inducing gains in maximal muscle strength in healthy populations, by now also comprising patients suffering from various clinical musculoskeletal conditions. The certainty in the estimates was low-to-very low, prompting the inclusion of future higher-quality trials.Trial registrationPROSPERO ID (CRD42022337173). Registered June 18th 2022.

Study on modified VAc-VeoVa10 latex prepared by soap-free emulsion polymerization

Modified latex is prepared via the soap-free emulsion polymerization of ethyl acetate (VAc) and vinyl versatate (VeoVa10). DFHMA is used as modified monomers. The composite surfactants of SR-10 and ANPEO-10 are used as the composite emulsifiers. The polymerization is initiated by potassium sulfate (KPS). The structure of latex film was characterized by Fourier transform infrared spectroscopy (FTIR). The latex films were tested by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and contact angle (CA) determinator. The particle size of the latex emulsion particle size is determined by the Zetatrac dynamic light scatter. Results show that the optimum condition of preparing the modified latex can be obtained, i.e. the amount of emulsifier is 4.0%; the mass ratio of SR-10 to ANPEO-10 is 1:1; the amount of initiator is 0.5%; the mass ratio ofVAc to VeoVa10 is 1:1; the amount of DFHMA is 5.0%. The appearance of the latex is blue and translucent with a small particle size. The conversion rate is more than 98%. Compared with the conventional latex, the hydrophobicity and heat resistance of the film have been improved. Moreover, the latex has good chemical stability and mechanical stability.

Effect of Succinamic Acid Derivative on the Growth Kinetics and Induction of Apoptosis in a Cancer Cell Line.

Introduction Head and neck cancers are heterogeneous malignancies associated with significant morbidity. Oral cancers are related to the use of tobacco products. Smokeless tobacco usage is a health problem worldwide, and its carcinogenic mechanism is largely unknown. Despite advances in conventional treatments, side effects and drug resistance remain unsolved. Therefore, novel therapeutic agents with minimal side effects using plant derivatives should be explored. An active antihyperglycemic and antioxidant compound known as FIIc was isolated from the fruit pulp of Eugenia jambolana (US Patent No.: 2,30,753). Although E. jambolana is reported to have anticancer activity, no study has been reported on its growth kinetics andapoptotic potential in the human head and neck cancer cell line (SCC4). The present study evaluated the effect of an herbal compound isolated from the fruit pulp of E. jambolana and chemically synthesized the same compound, α-hydroxy succinamic acid (α-HSA), on SCC4 proliferation and apoptotic gene expression. Methods The SCC4 cell line was cultured in Dulbecco's Modified Eagle Medium (DMEM). The dosages of smokeless tobacco extract (STE), herbal compound, and synthetic compound were determined by cell viability assay, and their effect on mRNA expression of apoptotic genes was measured by real-time polymerase chain reaction. Results The present study observed significant therapeutic effects of the natural and synthetic compounds from the fruit pulp of E. jambolana at the concentration range of 100-200 μg/mL on the SCC4 cell line. α-HSA had antiproliferative action; upregulated apoptotic genes like p53, p21, and Bax; and downregulated anti-apoptotic genes like survivin in the SCC4 cell line. Conclusion The therapeutic potential of α-HSA and the putative mechanisms involved may be explored to provide the basis for future therapeutic interventions in oral cancer mediated by smokeless tobacco.

Dynamics Analysis of Droplets Collision with the Wall Driven by Buoyancy

Dynamics analysis of the oil droplet in water impacting on a rigid wall in the range of Re=9.3 ∼ 231.39, We=0.003 ∼ 0.637 was carried out by combining microscopic experiment with theoretical study. In the oil droplet’s force equation, we consider the added mass force and the water film induced force, in addition to the conventional forces, i.e. buoyancy and resistance to flow. Stokes-Reynolds drainage equation (i.e. SR model) and Young-Laplace equation (i.e. YL model) are combined with the force equation to numerically solve the motion law of oil droplets near the wall for different control parameters. The study indicates that coupled model would expect oil droplet velocities, motion trajectories and capture the kinetic behaviors of the water-film drainage evolution. The interfacial deformation of oil droplets causes changes in the pressure and the pressure distribution pattern has an important relationship with the shape of the oil droplet interface. These two forces play a dominant role in droplet motion during the collision and the maximum value of these two forces increases with increasing droplet size and Re number. Future research should shift towards complex oil-water systems and consider the effects of chemicals on oil droplets so that the application of the model will be more generalisable. At the same time, computer technology should be used to transfer the two-dimensional view to a three-dimensional view to analyse the deformation of the oil-water interface and to better understand the drainage process of the water film.

Detailed evaluation of electric demand load shifting potential of heat pump water heaters in a hot humid climate

Heat pump water heaters (HPWH) are a proven method of reducing water heating energy use over prevailing electric resistance systems (ERWH). Both technologies lend themselves to enhanced control for peak load reduction. Laboratory tests were conducted in Central Florida using the CTA-2045 standard to evaluate load shifting strategies with connected water heaters. Four HPWHs from three manufacturers, including two different tank volumes, were tested alongside an ERWH in a garage-like environment. Tests aimed to shift energy use away from utility peak load periods to off-peak times when excess renewable energy resources are often available. Two load-shifting strategies were shown effective, Shed and Critical Peak, with variation by manufacturer. Beyond draw volume, other factors influenced HPWH load shifting: Florida winter conditions, which increase the energy used per draw, provided the greatest challenges to complete load shift. Inlet water temperature had a large impact on the success of load reduction. Ground temperatures in which water pipes were buried largely determined inlet water temperatures. HPWH efficiency setting: Heat pump water heaters often default to a “hybrid” mode that may use some electric resistance heat to minimize risk of running out of hot water. Operational mode can impact load shifting potential.