Conventional micro-CT Research Articles

Design, In Vitro Evaluation and In Vivo Biocompatibility of Additive Manufacturing Three-Dimensional Printing of β beta-Tricalcium Phosphate Scaffolds for Bone Regeneration

The reconstruction of bone deficiencies remains a challenge due to the limitations of autologous bone grafting. The objective of this study is to evaluate the bone regeneration efficacy of additive manufacturing of tricalcium phosphate (TCP) implants using lithography-based ceramic manufacturing (LCM). LCM uses LithaBone TCP 300 slurry for 3D printing, producing cylindrical scaffolds. Four models of internal scaffold geometry were developed and compared. The in vitro studies included cell culture, differentiation, seeding, morphological studies and detection of early osteogenesis. The in vivo studies involved 42 Wistar rats divided into four groups (control, membrane, scaffold (TCP) and membrane with TCP). In each animal, unilateral right mandibular defects with a total thickness of 5 mm were surgically performed. The animals were sacrificed 3 and 6 months after surgery. Bone neoformation was evaluated by conventional histology, radiology, and micro-CT. Model A (spheres with intersecting and aligned arrays) showed higher penetration and interconnection. Histological and radiological analysis by micro-CT revealed increased bone formation in the grafted groups, especially when combined with a membrane. Our innovative 3D printing technology, combined with precise scaffold design and efficient cleaning, shows potential for bone regeneration. However, further refinement of the technique and long-term clinical studies are crucial to establish the safety and efficacy of these advanced 3D printed scaffolds in human patients.

Daily administration of parathyroid hormone slows the progression of basic multicellular units in the cortical bone of the rabbit distal tibia.

Basic Multicellular Units (BMUs) conduct bone remodeling, a critical process of tissue turnover which, if imbalanced, can lead to disease, including osteoporosis. Parathyroid hormone (PTH 1-34; Teriparatide) is an osteoanabolic treatment for osteoporosis; however, it elevates the rate of intra-cortical remodeling (activation frequency) leading, at least transiently, to increased porosity. The purpose of this study was to test the hypothesis that PTH not only increases the rate at which cortical BMUs are initiated but also increases their progression (Longitudinal Erosion Rate; LER). Two groups (n = 7 each) of six-month old female New Zealand white rabbits were both administered 30 μg/kg of PTH once daily for a period of two weeks to induce remodeling. Their distal right tibiae were then imaged in vivo by in-line phase contrast micro-CT at the Canadian Light Source synchrotron. Over the following two weeks the first group (PTH) received continued daily PTH while the second withdrawal group (PTHW) was administrated 0.9 % saline. At four weeks all animals were euthanized, their distal tibiae were imaged by conventional micro-CT ex vivo and histomorphometry was performed. Matching micro-CT datasets (in vivo and ex vivo) were co-registered in 3D and LER was measured from 612 BMUs. Counter to our hypothesis, mean LER was lower (p < 0.001) in the PTH group (30.19 ± 3.01 μm/day) versus the PTHW group (37.20 ± 2.77 μm/day). Despite the difference in LER, osteonal mineral apposition rate (On.MAR) did not differ between groups indicating the anabolic effect of PTH was sustained after withdrawal. The slowing of BMU progression by PTH warrants further investigation; slowed resorption combined with elevated bone formation rate, may play an important role in how PTH enhances coupling between resorption and formation within the BMU. Finally, the prolonged anabolic response following withdrawal may have utility in terms of optimizing clinical dosing regimens.

Super-resolution model-based iterative reconstruction for lens-coupled micro-CT imaging

Lens-coupled high-resolution micro-computed tomography (micro-CT) uses a visible light magnification system behind the x-ray path to achieve higher resolution imaging than conventional micro-CT. However, the spatial resolution is theoretically limited by optical diffraction and mechanical control precision. As a result, the current system resolution is still insufficient for some applications, such as the imaging of biological materials whose structures are on the nanometer scale. To overcome this limitation, a super-resolution algorithm can be employed to improve the image resolution beyond the theoretical upper bound of the ideal spatial resolution of the system. In this work, a super-resolution model-based iterative reconstruction (SR-MBIR) algorithm is proposed based on a lens-coupled high-resolution micro-CT system and a high-precision nano-stage attached to the rotation stage of the system. The algorithm employs a scanning program that dithers the object via the nano-stage to obtain multiple sets of projection images with sub-pixel information. The blur and noise statistical models are introduced into the physical model for iterative reconstruction, allowing for super-resolution, deblurring, and noise suppression. The results of simulation data and actual data show that the SR-MBIR algorithm has a prominent effect in improving image resolution. The reconstructed images have sharper edges, better details, higher signal-to-noise ratio, and can effectively suppress the systematic blur and noise in the imaging process, thus achieving superior interior reconstruction quality.

Visualization of temporomandibular joint articular cartilage using synchrotron-radiation X-ray phase-contrast imaging

X-ray phase-contrast imaging using synchrotron radiation was applied to visualize non-invasively the fine structures of articular cartilage of temporomandibular joint (TMJ). Among various X-ray phase-contrast imaging methods, we chose diffraction enhanced imaging (DEI) and carried out experiments using synchrotron radiation, aiming to visualize TMJ articular cartilage of rats and to identify the optimum X-ray energy. For comparison, the same sample was observed by a conventional laboratory X-ray source and X-ray micro-CT apparatus. DEI was able to visualize the articular cartilage of the mandibular condyle, which was not possible with the conventional laboratory X-ray source and X-ray micro-CT apparatus. DEI could also visualize the fibrous and proliferative layers in the articular cartilage of the mandibular condyle. We found that the optimum imaging energy was 20 keV for our sample. It was shown that DEI is a promising method for non-invasive visualization of TMJ articular cartilage. Our findings will open up new possibilities for applications of DEI with synchrotron radiation for basic medical and preclinical research.

Ultrasensitive US Microvessel Imaging of Hepatic Microcirculation in the Cirrhotic Rat Liver.

Background Liver microcirculation dysfunction plays a vital role in the occurrence and development of liver diseases, and thus, there is a clinical need for in vivo, noninvasive, and quantitative evaluation of liver microcirculation. Purpose To evaluate the feasibility of ultrasensitive US microvessel imaging (UMI) in the visualization and quantification of hepatic microvessels in healthy and cirrhotic rats. Materials and Methods In vivo studies were performed to image hepatic microvasculature by means of laparotomy in Sprague-Dawley rats (five cirrhotic and five control rats). In vivo conventional power Doppler US and ex vivo micro-CT were performed for comparison. UMI-based quantifications of perfusion, tortuosity, and integrity of microvessels were compared between the control and cirrhotic groups by using the Wilcoxon test. Spearman correlations between quantification parameters and pathologic fibrosis, perfusion function, and hepatic hypoxia were evaluated. Results UMI helped detect minute vessels below the liver capsule, as compared with conventional power Doppler US and micro-CT. With use of UMI, lower perfusion indicated by vessel density (median, 22% [IQR, 20%-28%] vs 41% [IQR, 37%-46%]; P = .008) and fractional moving blood volume (FMBV) (median, 6.4% [IQR, 4.8%-8.6%] vs 13% [IQR, 12%-14%]; P = .008) and higher tortuosity indicated by the sum of angles metric (SOAM) (median, 3.0 [IQR, 2.9-3.0] vs 2.7 [IQR, 2.6-2.9]; P = .008) were demonstrated in the cirrhotic rat group compared with the control group. Vessel density (r = 0.85, P = .003), FMBV (r = 0.86, P = .002), and median SOAM (r = -0.83, P = .003) showed strong correlations with pathologically derived vessel density labeled with dextran. Vessel density (r = -0.81, P = .005) and median SOAM (r = 0.87, P = .001) also showed strong correlations with hepatic tissue hypoxia. Conclusion Contrast-free ultrasensitive US microvessel imaging provided noninvasive in vivo imaging and quantification of hepatic microvessels in cirrhotic rat liver. © RSNA, 2022 Supplemental material is available for this article. See also the editorial by Fetzer in this issue.

Development of a digital zebrafish phantom and its application to dedicated small-fish PET

Objective. We are developing a small-fish positron emission tomography (PET) scanner dedicated to small aquatic animals relevant for biomedical and biological research, e.g. zebrafish. We plan to use Monte Carlo simulations to optimize its configuration and the required water-filled imaging chambers. Our objectives were: (1) to create a digital 3D zebrafish phantom using conventional micro-CT, (2) include the phantom into a simulated PET environment based on the framework GATE, and (3) investigate the effects of the water environment on the reconstructed images. Approach. To create the phantom, we performed ex vivo measurements of zebrafish specimen using a tabletop micro-CT and compared three methods to fixate the specimen. From segmented micro-CT images we created digital emission and transmission phantoms which were incorporated in GATE via tessellated volumes. Two chamber sizes were considered. For reference, a simulation with the zebrafish in air was implemented. The simulated data were reconstructed using CASToR. For attenuation correction, we used the exact attenuation information or a uniform distribution (only water). Several realizations of each scenario were performed; the reconstructed images were quantitatively evaluated. Main results. Fixation in formalin led to the best soft-tissue contrast at the cost of some specimen deformation. After attenuation correction, no significant differences were found between the reconstructed images. The PET images reflected well the higher uptake simulated in the brain and heart, despite their small size and surrounding background activity; the swim bladder (no activity) was clearly identified. The simplified attenuation map, consisting only of water, slightly worsened the images. Significance. A conventional micro-CT can provide sufficient image quality to generate numerical phantoms of small fish without contrast media. Such phantoms are useful to evaluate in-silico small aquatic animal imaging concepts and develop imaging protocols. Our results support the feasibility of zebrafish PET with an aqueous environment.

How to Make a Vampire: Part II. Getting Ready to Feed

The mammalian feeding system is made up of multiple components that influence facial variation, including the masticatory muscles, bony jaw apparatus, and teeth. However, it is not fully understood how the development of these components are coordinated and are impacted by life history and diet.Bats are the only mammals that continue to nurse until they are almost adult size, and often after they become volant. Common vampire bats (Desmodus rotundus) have a relatively prolonged juvenile period among bats, can nurse up to nine months, and later solely subsist off of blood. Feeding system maturity may therefore be delayed in bats, and particularly delayed in Desmodus, as a result of their lengthy juvenile period and liquid diet. In this study, we examine the developmental maturity of the cranium and feeding apparatus in the late fetus of a common vampire bat (Desmodus rotundus) relative to an adult (its mother).The heads of each specimen were microCT scanned twice. Conventional microCT was used to image mineralized tissues. Diffusible iodine‐based contrast‐enhanced CT (diceCT) imaging was used to image soft tissues. Cranial length and palate length measurements were acquired from unstained scans to evaluate size and jaw apparatus development. Masticatory muscles (e.g., medial pterygoid, zygomaticomandibularis) and permanent tooth crypt volumes were acquired from stained tissue scans to evaluate masticatory muscle and tooth development. Developmental maturity of these structures was assessed by calculating a percentage of the growth completed (i.e., [fetal muscle volume/adult muscle volume]*100).In the fetus, permanent tooth crypt volume is already comparable to the adult condition despite cranial length and palate length being &lt;75% of adult size. Masticatory muscle volume maturity is highest in the lateral pterygoid muscle (~35%), whereas other masticatory muscles are far less developed (e.g., medial pterygoid volume maturity, ~20%; temporalis profundus volume maturity, ~20%; temporalis medius volume maturity, ~6%).These results reveal highly precocious permanent tooth development in Desmodus. Although this may facilitate transition to hematophagy, Desmodus do not fly until eight to ten weeks, so the precocious incisors may primarily aid the infant to grip its mother’s skin. Differential development of the masticatory muscles may also be influenced by the need for young bats to use their mouths to help anchor themselves to their mother early in life. This may explain the advanced maturity of the lateral pterygoid muscle, which would protrude the jaw and help to facilitate a more secure grip.

Follow Your Nose: Ontogeny of the Olfactory Duct in Primates

Most primates are characterized by orbital convergence, the displacement of the orbits toward the rostral midline. In platyrrhine primates and tarsiers, this convergence is so extreme that orbits meet in the midline at the apical interorbital septum. This produces a spatial separation of the anterior cranial fossa and the nasal cavity. The olfactory bulbs of the brain pass dorsal and then rostral to the orbits to reach the nasal cavity via a bony tube, the olfactory duct. Nerves are expected to constrain growth of musculoskeletal structures. We hypothesized that the network of olfactory nerves effectively tethers the olfactory bulbs to the mucosa of the nasal cavity, and the growth of facial structures in these primates results in rostral displacement of the olfactory bulbs through ontogeny. In addition, growth of the midface may be constrained by this functional relationship.This comparative analysis was based on 3D reconstructions of cranial structures in newborns and adults from representative platyrrhine species (e.g., Aotus nancymaae and Cebuella pygmaea) and tarsiers (Tarsius syrichta). Spatial relationships of the olfactory duct were estimated using endocasts based on conventional microCT scans. In addition, diffusion iodine contrast‐enhanced CT (diceCT) images were used to study Aotus nancymaae at multiple stages of ontogeny. DiceCT allowed us to reconstruct the actual position of olfactory bulbs relative to the olfactory duct and the distribution of olfactory nerves in the nasal cavity. 3DSlicer and Blender software were used to render 3D models. These data confirm our hypothesis that the rostral projection of the olfactory bulbs relative to the frontal lobes of the brain increases through ontogeny. In addition, the paths of olfactory nerves are diverted around the convergent eyes. The ontogenetic relationships occurring in platyrrhine and tarsier olfactory ducts have evolutionary implications for biological variation in the primate skull.

Diffusible contrast-enhanced micro-CT improves visualization of stented vessels

In this report, we showcase diffusible iodine-based contrast-enhanced computed tomography (DICE-CT) as a method for improving soft tissue visualization and reducing beam hardening artifact within a stented vessel. This technique is commonly used in our pathology lab to image soft tissue specimens with dense metal implants and to ensure reliable morphological analysis through clear delineation of tissue structures. For this report, a porcine right coronary artery with an implanted metal stent was scanned using both conventional and DICE-CT methods. Upon reconstruction, DICE-CT produced less beam hardening artifact in comparison to traditional micro-CT; furthermore, DICE-CT produced results with morphometric similarity to histology. Accordingly, these differences illustrated the clear advantage of using DICE-CT over conventional micro-CT when imaging soft tissue specimens with dense metal implants.

Photon Counting CT and Radiomic Analysis Enables Differentiation of Tumors Based on Lymphocyte Burden.

The purpose of this study was to investigate if radiomic analysis based on spectral micro-CT with nanoparticle contrast-enhancement can differentiate tumors based on lymphocyte burden. High mutational load transplant soft tissue sarcomas were initiated in Rag2+/− and Rag2−/− mice to model varying lymphocyte burden. Mice received radiation therapy (20 Gy) to the tumor-bearing hind limb and were injected with a liposomal iodinated contrast agent. Five days later, animals underwent conventional micro-CT imaging using an energy integrating detector (EID) and spectral micro-CT imaging using a photon-counting detector (PCD). Tumor volumes and iodine uptakes were measured. The radiomic features (RF) were grouped into feature-spaces corresponding to EID, PCD, and spectral decomposition images. The RFs were ranked to reduce redundancy and increase relevance based on TL burden. A stratified repeated cross validation strategy was used to assess separation using a logistic regression classifier. Tumor iodine concentration was the only significantly different conventional tumor metric between Rag2+/− (TLs present) and Rag2−/− (TL-deficient) tumors. The RFs further enabled differentiation between Rag2+/− and Rag2−/− tumors. The PCD-derived RFs provided the highest accuracy (0.68) followed by decomposition-derived RFs (0.60) and the EID-derived RFs (0.58). Such non-invasive approaches could aid in tumor stratification for cancer therapy studies.

A phase-contrast micro-CT system for non-destructive testing of light materials

High-resolution computed tomography (micro-CT) plays a crucial role in material science. The conventional micro-CT method, which is based on x-ray absorption, performs well when imaging hard and dense materials, but for objects with weak x-ray absorption the contrast is poor. If the phase shift is detected alongside absorption, the image contrast can be increased. We here present a propagation-based phase-contrast micro-CT system, based on a MetalJet x-ray source, and show an application of phase-contrast micro-CT for imaging a carbon-fibre composite. Individual carbon fibres could be visualised, and also small air cavities within the material. This enables high-resolution three-dimensional inspection of light materials, such as carbon composites and plastics.

When the Utility of Micro-Computed Tomography Collides with Insect Sample Preparation: An Entomologist User Guide to Solve Post-Processing Issues and Achieve Optimal 3D Models

Many techniques are used today to study insect morphology, including light and electron microscopy. Most of them require to specifically prepare the sample, precluding its use for further investigation. In contrast, micro-CT allows a sample to be studied in a non-destructive and rapid process, even without specific treatments that might hinder the use of rare and hard-to-find species in nature. We used synchrotron radiation (SR) micro-CT and conventional micro-CT to prepare 3D reconstructions of Diptera, Coleoptera, and Hymenoptera species that had been processed with 4 common preparation procedures: critical-point drying, sputter-coating, resin embedding, and air-drying. Our results showed that it is possible to further utilize insect samples prepared with the aforementioned preparation techniques for the creation of 3D models. Specimens dried at the critical point showed the best results, allowing us to faithfully reconstruct both their external surface and their internal structures, while sputter-coated insects were the most troublesome for the 3D reconstruction procedure. Air-dried specimens were suitable for external morphological analyses, while anatomical investigation of soft internal organs was not possible due to their shrinking and collapsing. The sample included in resin allowed us to reconstruct and appreciate the external cuticle and the internal parts. In this work, we demonstrate that insect samples destined to different analyses can be used for new micro-CT studies, further deepening the possibility of state-of-the-art morphological analyses.

Calcified cartilage revealed in whole joint by X-ray phase contrast imaging

ObjectiveX-ray Phase Contrast Imaging (PCI) is an emerging modality that will be in the next few years available in a wider range of preclinical set-ups. In this study, we compare this imaging technique with conventional preclinical modalities in an osteoarthritis mouse model. MethodPhase contrast technique was performed on 6 post-mortem, monoiodoacetate-induced osteoarthritis knees and 6 control knees. The mice knees were then imaged using magnetic resonance imaging and conventional micro computed tomography. Examples of imaging surrogate markers are reported: local distances within the articular space, cartilage surface roughness, calcified cartilage thickness, number, volume and locations of osteophytes. ResultsThanks to PCI, we can show in 3D calcified cartilage without contrast agent by a non-invasive technique. The phase contrast images reveal more details than conventional imaging techniques, especially at smaller scales, with for instance a higher number of micro-calcifications detected (57, 314 and 329 for MRI, conventional micro-CT and phase contrast imaging respectively). Calcified cartilage thickness was measured with a significant difference (p ​< ​0.01) between the control (23.4 ​± ​17.2 ​μm) and the osteoarthritis induced animal (46.9 ​± ​19.0 ​μm). ConclusionsX-ray phase contrast imaging outperforms the conventional imaging modalities for assessing the different tissue types (soft and hard). This new imaging modality seems to bring new relevant surrogate markers for following-up small animal models even for low-grade osteoarthritis.

Direct Assessment of Rabbit Cortical Bone Basic Multicellular Unit Longitudinal Erosion Rate: A 4D Synchrotron-Based Approach.

Cortical bone remodeling is carried out by basic multicellular units (BMUs), which couple resorption to formation. Although fluorochrome labeling has facilitated study of BMU formative parameters since the 1960s, some resorptive parameters, including the longitudinal erosion rate (LER), have remained beyond reach of direct measurement. Indeed, our only insights into this spatiotemporal parameter of BMU behavior come from classical studies that indirectly inferred LER. Here, we demonstrate a 4D in vivo method to directly measure LER through in-line phase contrast synchrotron imaging. The tibias of rabbits (n=15) dosed daily with parathyroid hormone were first imaged in vivo (synchrotron micro-CT; day 15) and then ex vivo 14 days later (conventional micro-CT; day 29). Mean LER assessed by landmarking the co-registered scans was 23.69 ± 1.73 μm/d. This novel approach holds great promise for the direct study of the spatiotemporal coordination of bone remodeling, its role in diseases such as osteoporosis, as well as related treatments. © 2022 The Authors. Journal of Bone and Mineral Research published by Wiley Periodicals LLC on behalf of American Society for Bone and Mineral Research (ASBMR).

Co-Registration of Peripheral Atherosclerotic Plaques Assessed by Conventional CT Angiography, MicroCT and Histology in Patients with Chronic Limb Threatening Ischaemia

To co-register conventional computed tomography angiography (CTA), with exvivo micro-computed tomography (microCT) and histology of popliteal atherosclerotic plaques. Improving the non-invasive imaging capabilities may be valuable to advance patient care with peripheral arterial obstructive disease towards lesion and individual based treatment. In this prospective observational study, 12 popliteal arteries from 11 symptomatic patients who had undergone transfemoral amputations for chronic limb threatening ischaemia and who had pre-operative CTA, were analysed exvivo by microCT and histology. A total of 353 histological cross sections were co-registered with microCT and CTA, and classified as: lipid rich (LP, n=26), fibrous (FP, n=80), or calcific (CP, n=247) plaques. CTA and microCT plaque density was calculated in 791 regions of interest as Hounsfield units (HU). CTA and microCT could identify plaque components that were confirmed by histology such as fibrous tissue (FP), lipid pool/core (LP), and calcification (CP). MicroCT densities were 77.8 HU for FP (IQR 52.8, 129.5 HU),-28.4 HU for LP (IQR-87.1, 13.2 HU), and 3826.0 HU for CP (IQR 2989.0, 4501.0 HU). CTA densities of the three components of the plaque were: 78.0 HU for FP (IQR 59.5, 119.8 HU), 32.5 HU for LP (IQR 15.0, 42 HU), and 641.5 HU for CP (IQR 425.8, 1135 HU). The differences were statistically significant between the HU densitometric characteristics among the three groups (p<.0001) for both imaging modalities. Overall, microCT performed better diagnostically than conventional CTA for the three types of plaques: areas under the receiving operator characteristics curve were greater for microCT than CTA for FP (0.97 vs. 0.90), for LP (0.88 vs. 0.67), and for CP (0.97 vs. 0.90). CTA and microCT can be used to identify histological atherosclerotic plaque components, with better diagnostic performance for microCT. This study demonstrates the feasibility of using microCT to assess plaque morphology lesions in a manner that approaches histology thus becoming a useful tool for exvivo assessment of atherosclerosis and towards lesion based treatment.

Mechanical loading prevents bone destruction and exerts anti-tumor effects in the MOPC315.BM.Luc model of myeloma bone disease

Bone continually adapts to changing external loading conditions via (re)modeling (modeling and remodeling) processes. While physical activity is known to beneficially enhance bone mass in healthy individuals, little is known in how physical stimuli affect osteolytic bone destruction in patients suffering from multiple myeloma bone disease. Multiple myeloma (MM) is caused by malignant plasma cells in the bone marrow, shifting the balance in bone remodeling towards massive resorption. We hypothesized that in vivo tibial mechanical loading has anabolic effects in mice with locally injected MOPC315.BM.Luc cells. Conventional microCT analysis revealed enhanced cortical bone mass and microstructure in loaded compared to nonloaded mice. State-of-the-art time-lapse microCT based image analysis demonstrated bone (re)modeling processes at the endosteal and periosteal surfaces as the underlying causes of increased bone mass. Loading prevented the progression and development of osteolytic destruction. Physical stimuli also diminished local MM cell growth and dissemination evidenced by quantification of MM cell-specific immunoglobulin A levels in the serum of mice and by bioluminescence analysis. These data indicate that mechanical loading not only rescues the bone phenotype, but also exerts cell-extrinsic anti-myeloma effects in the MOPC315.BM.Luc model. In conclusion, the use of physical stimuli should be further investigated as an anabolic treatment for osteolytic bone destruction in patients with MM.

Innovations in laboratory-based dynamic micro-CT to accelerate in situ research.

In the past few years, dynamic computed tomography (CT) approaches or uninterrupted acquisitions of deforming materials have rapidly emerged as an essential technique to understand material evolution, facilitating in situ investigations ranging from mechanical deformation to fluid flow in porous materials and beyond. Developments at synchrotron facilities have led this effort, pointing to the future of the technique. In the laboratory, recent developments at TESCAN XRE have made it possible to image, reconstruct and inspect dynamic processes in the laboratory with a temporal resolution below 10 s, meaning that an entire acquisition from 0 to 360° is completed within 10 s. The aim of this study is to explore the challenges and innovations that have led to the ability to perform high speed, dynamic acquisitions. A unique horizontally rotating gantry based micro-CT system was developed to facilitate complex in situ experiments. In doing so, the sample stays fixed while source and detector are uninterruptedly rotating around a vertical axis. In this work, the dynamic CT method with this rotating gantry based system will be described by two application examples: (1) deformation and collapse of a delicate beer foam and (2) in situ baking process of pastry. For the pastry baking process, an oven was needed to reach baking temperature. In a conventional micro-CT system, where the sample rotates, it is not so obvious to rotate an oven with sensor and heating cables. On the other hand, the delicate foam of a collapsing beer head is able to rotate, but because of the tangential convection during fast rotation (<10 s), it could influence the bubble detachment and liquid drainage and thus also the foam degradation. To investigate both processes, a horizontally rotating gantry based micro-CT is required. For both examples it was possible to quantify the key parameters such as pore size and distribution to better understand the rise and fall of porous foams. These examples will highlight the recent progress in adapting micro-CT workflows to accommodate uninterrupted imaging of dynamic events and point to opportunities for future continued development. LAY DESCRIPTION: Micro-CT allows the nondestructive visualisation of internal structures and is being used routinely in the field of Material Science, Geoscience, Life Science and more. Because of its nondestructive aspect, micro-CT is optimal to take repetitive scans of the same sample over time. The combination of taking different scans over time is so called time-resolved CT. By doing so, crucial insights can be obtained on how materials form, deform and perform over time or under certain external conditions. TESCAN XRE have made it possible to image, reconstruct and inspect dynamic processes in the laboratory with a temporal resolution below 10 s. The dynamic CT method will be described through the lens of two application examples: (1) deformation and collapse of a delicate beer foam and (2) in situ baking process of pastry. These examples will highlight the recent progress in adapting micro-CT workflows to accommodate imaging of dynamic events and point to opportunities for future continued development.

Synchrotron MicroCT Reveals the Potential of the Dual Contrast Technique for Quantitative Assessment of Human Articular Cartilage Composition.

ABSTRACTDual contrast micro computed tomography (CT) shows potential for detecting articular cartilage degeneration. However, the performance of conventional CT systems is limited by beam hardening, low image resolution (full‐body CT), and long acquisition times (conventional microCT). Therefore, to reveal the full potential of the dual contrast technique for imaging cartilage composition we employ the technique using synchrotron microCT. We hypothesize that the above‐mentioned limitations are overcome with synchrotron microCT utilizing monochromatic X‐ray beam and fast image acquisition. Human osteochondral samples (n = 41, four cadavers) were immersed in a contrast agent solution containing two agents (cationic CA4+ and non‐ionic gadoteridol) and imaged with synchrotron microCT at an early diffusion time point (2 h) and at diffusion equilibrium (72 h) using two monochromatic X‐ray energies (32 and 34 keV). The dual contrast technique enabled simultaneous determination of CA4+ (i.e., proteoglycan content) and gadoteridol (i.e., water content) partitions within cartilage. Cartilage proteoglycan content and biomechanical properties correlated significantly (0.327 < r < 0.736, p < 0.05) with CA4+ partition in superficial and middle zones at both diffusion time points. Normalization of the CA4+ partition with gadoteridol partition within the cartilage significantly (p < 0.05) improved the detection sensitivity for human osteoarthritic cartilage proteoglycan content, biomechanical properties, and overall condition (Mankin, Osteoarthritis Research Society International, and International Cartilage Repair Society grading systems). The dual energy technique combined with the dual contrast agent enables assessment of human articular cartilage proteoglycan content and biomechanical properties based on CA4+ partition determined using synchrotron microCT. Additionally, the dual contrast technique is not limited by the beam hardening artifact of conventional CT systems. © 2019 The Authors. Journal of Orthopaedic Research® published by Wiley Periodicals, Inc. on behalf of Orthopaedic Research Society. J Orthop Res 38:563–573, 2020

Application of a robotic THz imaging system for sub-surface analysis of ancient human remains

We used a robotic-based THz imaging system to investigate the sub-surface structure of an artificially mummified ancient Egyptian human left hand. The results obtained are compared to the results of a conventional CT and a micro-CT scan. Using such a robotic THz system promises new insights into the sub-surface structure of human remains. The depth resolution of the THz images exceeds the resolution of a conventional CT scan and is comparable with a micro-CT scan. The advantage of THz measurements over micro-CT scans is the fact that even comparatively large samples, like complete bodies, can be scanned. These would not fit into a conventional micro-CT scanner.

Evaluation of flow and filling of root canal sealers using different methodologies

Abstract Introduction Flow and filling ability of root canal sealers are indispensable for hermetic sealing of the root canal. Micro-computed tomography (micro-CT) can be used as a complementary methodology to evaluate such properties. Objective To evaluate the flow and filling ability of AH Plus, Endofill and Sealapex by conventional methodology and micro-CT. Material and method The flow of the sealers was analyzed according to ISO 6876/2012 and complemented by the area evaluation. Glass plates were manufactured with diameters of 1×1×2 mm and 1×1×1 mm (length, width and height), with a central cavity and four grooves in the horizontal and vertical directions. Each material was placed in the central cavity. Another glass plate and a metal weight were placed on the cement and kept for 10 minutes. The glass plate/sealer set was scanned using micro-CT. The flow was calculated by linear measurement of the material in the grooves. The central filling (mm3) was calculated in the central cavity and the lateral filling was measured up to 2 mm from the central cavity. Data were submitted to ANOVA/Tukey tests (α=0.05). Result All evaluated sealers presented flow according to ISO 6876 standards. The materials showed central cavity filling capacity higher than 80% and lateral filling greater than 75%. There was no difference in flow (mm and mm2) and in the filling ability (mm3) provided by the materials (p&gt;0.05). Conclusion All evaluated root canal sealers showed adequate flow and filling capacity, suggesting their clinical application.