Conventional Cavity Research Articles

Antireflective vertical-cavity surface-emitting laser for LiDAR

Multijunction vertical-cavity surface-emitting lasers (VCSELs) have gained popularity in automotive LiDARs, yet achieving a divergence of less than 16° (D86) is difficult for conventional extended cavity designs due to multiple-longitudinal-mode lasing. Our innovation, the antireflective vertical-cavity surface-emitting laser (AR-VCSEL), addresses this challenge by introducing an antireflective light reservoir, where the electric field intensity is substantially higher than the gain region. This reduces the required cavity length for minimal divergence, preserving the single-longitudinal-mode lasing. A 6-junction AR-VCSEL array showcases a halved divergence and tripled brightness compared to its conventional counterpart. Various multijunction AR-VCSEL array designs achieve a divergence range of 8° to 16° (D86). Notably, a 7 μm AR-VCSEL emitter achieves 28.4 mW in single transverse mode lasing. AR-VCSEL stands out among semiconductor lasers, offering a well-balanced power density and brightness, making it a cost-effective solution for long-distance LiDARs. The antireflective cavity concept may inspire diverse applications in photonic devices beyond LiDARs.

Dielectric assist accelerating structures for compact linear accelerators of low energy particles in hadrontherapy treatments

Dielectric Assist Accelerating (DAA) structures based on ultralow-loss ceramic are being studied as an alternative to conventional disk-loaded copper cavities. This accelerating structure consists of dielectric disks with irises arranged periodically in metallic structures working under the TM02-π mode. In this paper, the numerical design of an S-band DAA structure for low beta particles, such as protons or carbon ions used for Hadrontherapy treatments, is shown. Four dielectric materials with different permittivity and loss tangent are studied as well as different particle velocities. Through optimization, a design that concentrates most of the RF power in the vacuum space near the beam axis is obtained, leading to a significant reduction of power loss on the metallic walls. This allows to fabricate cavities with an extremely high quality factor, over 100,000, and shunt impedance over 300 MΩ/m at room temperature. During the numerical study, the design optimization has been improved by adjusting some of the cell parameters in order to both increase the shunt impedance and reduce the peak electric field in certain locations of the cavity, which can lead to instabilities in its normal functioning.

Metasurface-Based Hybrid Optical Cavities for Chiral Sensing

Quantum metasurfaces, i.e., two-dimensional subwavelength arrays of quantum emitters, can be employed as mirrors towards the design of hybrid cavities, where the optical response is given by the interplay of a cavity-confined field and the surface modes supported by the arrays. We show that stacked layers of quantum metasurfaces with orthogonal dipole orientation can serve as helicity-preserving cavities. These structures exhibit ultranarrow resonances and can enhance the intensity of the incoming field by orders of magnitude, while simultaneously preserving the handedness of the field circulating inside the resonator, as opposed to conventional cavities. The rapid phase shift in the cavity transmission around the resonance can be exploited for the sensitive detection of chiral scatterers passing through the cavity. We discuss possible applications of these resonators as sensors for the discrimination of chiral molecules. Our approach describes a new way of chiral sensing via the measurement of particle-induced phase shifts. Published by the American Physical Society 2024

Modal analysis of a half-mode substrate integrated waveguide-fed slot-coupled dual-band patch antenna

This manuscript presents comprehensive modal analysis of a compact, half-mode SIW-fed slot-coupled dual-band antenna. The Characteristic Mode Analysis (CMA) is investigated in detail and presented for the first time to analyze the radiation behavior and frequency domain characteristics of the proposed structure. The number of dominant operative modes supported by the antenna is decided based on the number eigen factors, its corresponding values, and the characteristic angles. The antenna operates at 33 and 38.14 GHz with a return loss of 20.5 and 19.5 dB, a gain of 7.9 and 6.7 dBi, and an efficiency of 90% and 88%, respectively. Measured results are in close resemblance with the CMA, considering the difference between the conventional cavity modes and the characteristic modes of the proposed planar cavity configuration. The methodology can be extended to characterize any arbitrary shape radiating geometry.

Solving the spectral gap problem with a four-mirror bow-tie cavity in waveguide free-electron laser oscillators

The generation of intense coherent radiation pulses in the far-infrared and terahertz regimes is of considerable interest to the free-electron laser (FEL) radiation user community. At long wavelengths, the diffraction effect can be quite severe, therefore, an optical waveguide is required to confine the radiation field. However, it will also bring about some new phenomena, and the most noteworthy one is the spectral gap phenomenon: at some particular wavelengths, regardless of electron beam adjustments, the coupling efficiency and output power of waveguide FEL oscillators drop significantly. Such spectral gap has an adverse effect on experimental results since numerous experiments require continuous spectral scanning. In this paper, we propose to utilize a bow-tie cavity instead of conventional cavities to the waveguide FEL to solve the spectral gap problem. The simulation was carried out based on the parameters of FELiChEM, a newly built user facility in China. Numerical simulation code OPC combining with modified GENESIS is used to enable the modelling, for the first time, of a bow-tie cavity based FEL in the far-infrared wavelength regime. The simulation results indicate that this novel structure can effectively eliminate the spectral gaps and substantially enhance long-wavelength laser performance.

Design, fabrication, and characterization of a drift tube linac type double gap re-buncher cavity.

The Low Energy High Intensity Proton Accelerator (LEHIPA) at Bhabha Atomic Research Centre, India, has recently been commissioned to the target energy of 20MeV by beam acceleration through a 352MHz radio frequency quadrupole (RFQ) and drift tube linac (DTL). The medium energy beam transport (MEBT) line of LEHIPA matches the 3MeV beam from RFQ to the DTL using four electromagnetic quadrupoles and a re-buncher cavity. In the beam transport lines of high frequency linacs, TM010 mode single gap buncher cavities are conventionally used, while a double gap re-buncher cavity was chosen for the short length LEHIPA MEBT based on beam dynamics simulations. The 352MHz double gap re-buncher cavity has been designed in a DTL type geometry with a cell length of βλ. This double gap cavity is found to be more power efficient with a higher shunt impedance and transit time factor than the conventional single gap buncher cavity. Electromagnetic design simulations, fabrication details, low power and high-power RF test results, and beam test results of the re-buncher cavity are presented in this paper.

A low-frequency normal conducting cavity with higher-order mode damping for fourth-generation synchrotron radiation sources.

The utilization of a low-frequency (<200MHz) RF system in storage facilitates the attainment of ultra-low emittances in synchrotron light sources through on-axis injection. This paper focuses on the development of a low-frequency normal conducting (NC) cavity with higher-order mode (HOM) damping for fourth-generation synchrotron light sources. We propose a novel approach to achieve efficient HOM damping in a NC cavity by optimizing the lowest frequency HOM and implementing a beam-line absorber. Notably, unlike conventional NC cavities, the presence of a large beam tube for the beam-line absorber does not compromise the accelerating performance in a coaxial resonant cavity, enabling effective HOM damping while maintaining a high shunt impedance. Through simulations, the prototype design of a 166.6MHz HOM-damped cavity demonstrates a fundamental mode impedance of ∼8 MΩ, with longitudinal and transverse HOM impedances below 2.0 and 50 kΩ/m, respectively.

Impact of contracted endodontic access cavity designs on root canal disinfection using diode laser: An “In-Vitro” Study

Introduction: New approaches for minimal invasive endodontic access cavity designs had been introduced for preserving the structural integrity of the offending tooth. Diode laser has been now widely used in root canal disinfection and showing highly promising results. Aim: to evaluate the impact of contracted endodontic access cavity designs on root canal disinfection using diode laser. Materials and Methods: Fifty-four intact freshly extracted human mandibular first molars were selected for the use in this study. Only the mesial roots of the selected samples were included in this study. Samples were randomly divided into three equal groups (n=18) according to the type of access cavity performed. Group (1): conventional access cavities, Group (2): Ninja access cavities, and Group (3): truss access cavities. Isolates of Enterococcus Faecalis (E.Fecacalis) were introduced in the root canals of the mesial roots of the selected samples. Samples were further sub-divided into two equal sub-groups (n=9) according to the disinfection method. Sub-group (a): Diode laser disinfection, and Sub-group (b): NaOCl 2.5% followed by EDTA 17% irrigation. Bacterial evaluation was performed using confocal laser scanning electron microscope. Results: The results showed that using Diode laser disinfection have shown higher bacterial reduction in comparison to NaOCl irrigation, but with no statistically significant difference. For access cavity designs, regardless of the type of disinfection used, conventional access cavities have shown the highest bacterial reduction, with the least bacterial reduction with Ninja access cavities. Conclusion: Contracted endodontic access cavities did not offer any advantages in comparison with the conventional endodontic access cavities regarding bacterial reduction. Diode laser can be used as an effective adjunct tool in root canal disinfection.

Guided endodontics versus conventional access cavity preparation: an ex vivo comparative study of substance loss

BackgroundTo compare the outcomes of conventional access cavity preparation (CONV) versus guided endodontics (GE) for access cavity preparation in anterior teeth with pulp canal calcification (PCC) regarding root canal detection, substance loss, procedural time, and need for additional radiographs.MethodsExtracted, sound human teeth with PCC (n = 108) were matched in pairs, divided into two groups and used to produce 18 models. An independent endodontist and a general dentist performed access cavity preparation under simulated clinical conditions on nine models each (54 teeth). The endodontist used the conventional technique and the general dentist GE. Time needed to access the root canals and the number of additional radiographs were recorded. Pre- and postoperative cone-beam computed tomography scans were obtained to measure substance loss. Statistical significance was tested by examining the overlap of 95% confidence intervals (CIs) between the groups.ResultsAll root canals were successfully accessed by both methods. There were no significant differences in substance loss (CI: CONV 15.9–29.6 mm3 vs. GE 17.6-27.5mm3) or procedural time (CI: CONV 163.3-248.5 s vs. GE 231.9-326.8 s). However, 31 additional radiographs were required for GE compared to none for CONV.ConclusionsFor access cavity preparation in teeth with PCC, both CONV by a specialist and GE by a general dentist produce good results in terms of substance loss and time requirements.

Tunable Localization of Higher‐Order Bound States in Non‐Hermitian Optical Waveguide Lattices

AbstractHigher‐order corner‐bound states in a 2D structure have been found to possess robust and exotic properties beyond the “ordinary” topological edge states, giving rise to a promising applicative potential. For example, the topological nanocavity designed based on the corner states exhibits much better performance than that of the conventional photonic crystal cavity. However, the corner states in the finite Hermitian system are usually coupled with each other, which results in the weakening of their localization. As such, the contradiction between the performance and footprint of topological devices is vexing. Here, it shows that introducing non‐Hermiticity in the higher‐order topological insulators is an effective strategy to enhance the localization of corner states in finite systems. By designing and analyzing the 2D finite Su‐Schriffer‐Heeger optical lattices with two types of non‐Hermitian configuration, the localization degree of higher‐order corner states is found to depend on the gain/loss strength. This is experimentally demonstrated by observing the distribution of corner states in the femtosecond‐laser‐writing loss‐controlled waveguide arrays. This scheme tuning localization of higher‐order corner‐bound states by non‐Hermiticity may offer a new avenue to design robust and compact devices, such as topological nano‐lasers with an ultra‐low threshold.

Comparison of Two Different Intraoral Scanners for Determination of Caries Related Volume Loss in Caries Removal

Objective: The study aimed to compare cavity volume data obtained with two different intraoral scanners. Methods: One hundred extracted molar teeth were divided into groups according to ICDAS-II classification, and scanned with Cerec Omnicam (Dentsply Sirona) and iTero Element Flex (Align Technology). The caries-infected tissues were removed regarding either minimally invasive or conventional cavity principles. Samples were scanned again and volumetric data were assessed by Meshmixer 3.5 (Autodesk) 3D modeling software. Statistical evaluations were performed with Mann Whitney U test and Spearman’s Correlation test. The significance level was α=0.05. Results: Although there was a significant difference between obtained initial volume readings of two scanners for 3M and 3C groups (p &lt; 0.05), no significant difference was observed among other groups (p ≥ 0.05). Regarding the comparison of final volume readings of two scanners, a significant difference was found for 5M group (p = 0.036), whereas no significant difference was observed for other groups (p ≥ 0.05). Percentage of volume loss between two scanners was statistically similar (p ≥ 0.05). Conclusion: Data obtained with Cerec Omnicam and iTero Element Flex were compatible with volumetric assessments. Both intraoral scanners may be considered effective for calculating caries-related cavity volumes. Minimally invasive cavity principles may provide less volume loss compared to conventional cavity principles.

Hydrothermal impact of multiwall carbon nanotube diameter in a conventional square cavity

This study aimed to computationally examine the effect of the average diameter of multiwall carbon nanotubes (MWCNTs) on the hydrothermal properties of a square cavity. A conventional square cavity filled with MWCNT–water was used for the experiment. The left and right walls of the cavity are maintained as hot and cold respectively, whereas the top and bottom walls were assumed to be adiabatic. Mathematical models were developed using the Navier–Stokes equations by applying the thermophysical properties of the MWCNT–water nanofluid. A newly proposed correlation between the effective thermal conductivity and the diameter of carbon nanotube was utilized to analyze the impact of the average diameter on the natural convection of nanofluid inside the cavity. The governing equations were non-dimensionalized using suitable variables and then solved using the Galerkin finite element technique. The combined effects of the Rayleigh number (103<Ra<106) and the average diameter of the MWCNTs (10 nm to 30 nm) on the streamlines, isolines, velocity, local Nusselt number, and mean Nusselt number were examined in detail. It is found that the flow and heat transfer rate inside the cavity can be effectively controlled by increasing the average diameter of MWCNTs at higher Rayleigh numbers compared to lower Rayleigh number. A larger MWCNT diameter dominated the impact of the buoyancy force inside the square cavity.

Topological magnon-photon interaction for cavity magnonics

The study of cavity magnonics and topological insulators has made significant advances over the past decade, however the possibility of combining the two fields is still unexplored. Here, we explore such connection by investigating hybrid cavity systems that incorporate both a ferromagnet and a topological insulator. We find that electrons in the topological surface state efficiently mediate the effective electric dipole coupling between the spin of the ferromagnet and the electric field of the cavity, in contrast with the conventional cavity magnonics theory based on magnetic dipole coupling. We refer to this coupling as topological magnon-photon interaction, estimating it one order of magnitude stronger than the conventional magnon-photon coupling, and showing that its sign can be manipulated. We discuss the potential of our proposed device to allow for scaling down and controlling the cavity system using electronics. Our results provide solid ground for exploring the functionalities enabled by merging cavity magnonics with topological insulators.

The effects of laser and ultrasonic irrigation activation methods on smear and debris removal in traditional and conservative endodontic access cavities.

In this study, it was aimed to evaluate the smear and debris removal efficiency of laser and ultrasonic irrigation activation methods in traditional and conservative endodontic access cavity preparations. 60 freshly extracted human mandibular molar teeth were randomly divided into 2 groups according to the access cavity preparation (n = 30): Traditional endodontic access cavities (TEC) and Conservative endodontic access cavity (CEC). After the access cavity preparation, the mesiobuccal root canals were prepared to 35/0.4 with the VDW Rotate file system. Teeth with completed root canal preparation were randomly divided into 3 subgroups according to the final irrigation activation protocol (n = 30): Conventional needle irrigation, passive ultrasonic activation and laser activation. The crowns of the teeth were removed and the mesiobuccal roots were divided longitudinally into two halves, mesial and distal. Samples were scanned with scanning electron microscopy. Photomicrographs in the coronal, middle, and apical thirds of each specimen were taken at a magnification of 200 for debris and 1000 for evaluation of the smear layer. Data were analysed using the three-way Robust Anova test and Bonferroni test.The effect of access cavity design on remaining smear (p = 0.057) and debris (p = 0.5) was not statistically significant. The effect of the interaction of access cavity and irrigation activation on the remaining smear and debris was not statistically significant (p = 0.556, p = 0.333). Significantly fewer smears were detected in the laser activation group than in the ultrasonic activation and control groups. Conservative access cavities did not differ from conventional access cavities in terms of debris and smear.

Design and low-power measurement of 1.5 GHz TM020-type harmonic cavity for KEK future synchrotron light source

We designed a normal-conducting (NC) 1.5 GHz harmonic cavity that can be used in a future synchrotron light source at High Energy Accelerator Research Organization (KEK). By utilizing a higher TM020 mode for beam acceleration, this cavity has lower R/Q and higher unloaded Q as compared to those of conventional NC cavities. These features are advantageous in reducing the fluctuations in harmonic RF voltages when the bunch gaps are introduced. Harmful parasitic modes other than the TM020 mode can be heavily damped using coaxial slots located at the node of the TM020 mode. We made a concerted effort to lower the coupling impedances of parasitic modes while maintaining high Q value of the accelerating mode. We found that maintaining the axial symmetry of the cavity is essential for minimizing the leakage power of the accelerating mode into the coaxial slots. In this article, we present the optimization of the cavity shape, low-power measurement, and the basic design of a high-power model.

Numerical Investigation on the Ventilated Supercavity around a Body under Free Surface Effect

Reducing vessel resistance by using ventilated cavities has been a highly researched topic in the marine industry. There is limited literature on ventilated supercavities near the free surface, which indicates that their dynamic behavior is more complex than conventional ventilated cavities due to the effect of the free surface. This paper employs numerical simulations to study the dynamic behavior of the ventilated supercavity, taking into account the effect of the free surface. Numerical simulations can predict gas leakage behaviors, cavity geometry, and internal flow structures. The influence of the free surface shortens the length of the ventilated cavity and increases the diameter. The presence of the free surface mainly changes the vertical velocity distribution between the free surface and the cavity. The results show that there are two typical gas leakage mechanisms under different immersion depths: twin-vortex tube leakage mode and re-entrant jet leakage mode. The internal flow field of ventilated supercavity is classified into three regions: the internal boundary layer, the ventilation influence region, and the reverse flow region. As the distance between the free surface and the ventilated supercavity decreases, the ventilated supercavity is affected by both the free surface effect and the gravity effect.

The effect of ultrasonic access cavity preparation on dentinal inner walls: a micro-CT study on cadaveric samples.

The objective of this study is to evaluate the occurrence of coronal dentinal micro-cracks after access cavity refinement using high-speed burs and ultrasonic tips by means of micro-computed tomography (micro-CT) analysis. In this study, 18 mandibular cadaveric incisors were divided into two groups according to the protocol of the preparation of the conventional access cavity. The diamond bur 802 # 12 was used until the perforation of the pulp roof. Then, the Endo-Z bur was used for the group #1 and the ultrasonic tip Start-X # 1 for the group #2 to finish and refine the access cavity. The preparation time of each access cavity has been recorded. The teeth underwent a micro-CT scan before and after the preparation of the access cavity. Fisher's exact test, the Chi-square test, the Kolmogorov-Smirnov test, the Mann-Whitney test, and the Student's test were used for statistical evaluation. The percentage of teeth with new micro-cracks is not significantly different between the two groups (-p-value < 0.5). The number of newly formed micro-cracks and extension size were not significantly different between the two groups. The direction of extension of the micro- cracks was occluso-apical. The average duration of the access cavity is significantly smaller with the Endo-Z system (-p- value < 0.001). The roughness of walls surfaces has no statistically difference between the two groups. The use of ultrasound, although slower, is considered safe in the creation of dentinal micro-cracks, in the preparation of the access cavity.

An Angular Radial Extended Interaction Amplifier at the W Band

In this paper, an angular radial extended interaction amplifier (AREIA) that consists of a pair of angular extended interaction cavities is proposed. Both the convergence angle cavity and the divergence angle cavity, which are designed for the converging beam and diverging beam, respectively, are investigated to present the potential of the proposed AREIA. They are proposed and explored to improve the beam-wave interaction capability of W-band extended interaction klystrons (EIKs). Compared to conventional radial cavities, the angular cavities have greatly decreased the ohmic loss area and increased the characteristic impedance. Compared to the sheet beam (0°) cavity, it has been found that the convergence angle cavity has a higher effective impedance and the diverging beam has a weaker space-charge effect under the same ideal electron beam area; the advantages become more obvious as the propagation distance increases. Particle-in-cell (PIC) results have shown that the diverging beam (8°) EIA performs better at an output power of 94 GHz under the condition of lossless, while the converging beam (-2°) EIA has a higher output power of 6.24 kW under the conditions of ohmic loss, an input power of 0.5 W, and an ideal electron beam of 20.5 kV and 1.5 A. When the loss increases and the beam current decreases, the output power of the -2° EIA can be improved by nearly 30% compared to the 0° EIA, and the -2° EIA has a greatly improved beam-wave interaction capacity than conventional EIAs under those conditions. In addition, an angular radial electron gun is designed.

Design of Miniaturised Circular Polarisation-Reconfigurable and Frequency Agile Slow-Wave SIW Based Microstrip Antenna for Wireless Applications

ABSTRACT Maintaining acceptable radiation performance over the entire operation bandwidth is a significant challenge in development of a miniaturized reconfigurable antenna To address this issue, a new Substrate Integrated Waveguide (SIW) based reconfigurable antenna using slow wave structure is presented in this study. The proposed SIW antenna is based on a layered construction with metallic blind vias connecting to ground plane of SIW. The multi-layer structure of SIW with blind vias helps to separate magnetic and electric fields in the SIW cavity. Thus, a slow wave effect is also utilized and it leads to 36% reduction in the antenna size as compared to conventional SIW cavity. To attain the polarization and frequency reconfiguration, a cross slot is introduced in the top metallic layer of the SIW cavity and four PIN diodes are connected into the cross-slot arms. Experimental results exhibit frequency reconfigurability in different operating regions with resonant frequencies 4.35, 5, 5.8, 6.4, and 9.6 GHz. The polarization reconfigurability of the proposed antenna is achieved at 5 GHz with LP/RHCP/LHCP. The proposed antenna exhibits 3-dB axial ratio bandwidth of 4.8 to 5.2 GHz with peak gain of 4.2 dBi.

Multi-mode analysis of surface losses in a superconducting microwave resonator in high magnetic fields.

This paper reports on a surface impedance measurement of a bulk metal niobium-titanium superconducting radio frequency (SRF) cavity in a magnetic field (up to 10T). A novel method is employed to decompose the surface resistance contributions of the cylindrical cavity end caps and walls using measurements from multiple TM cavity modes. The results confirm that quality factor degradation of a NbTi SRF cavity in a high magnetic field is primarily from surfaces perpendicular to the field (the cavity end caps), while parallel surface resistances (the walls) remain relatively constant. This result is encouraging for applications needing high Q cavities in strong magnetic fields, such as the Axion Dark Matter eXperiment because it opens the possibility of hybrid SRF cavity construction to replace conventional copper cavities.